Professional Documents
Culture Documents
- Password protection for programming mode ESM-7710 Note-1: If input type is selected PTC or NTC (BC = 12, 15, 18, 19 ),
ESM series temperature controllers are designed for measuring and Temperature sensor is given with the device. For this reason,
PTC, NTC
controlling temperature. They can be used in many applications with On/Off If input type is selected as PTC, sensor type (V = 0, 1 or 2) or 48 mm/ 1.89 inch
OUTPUT-2 OUTPUT-1 11 ± 1 mm /0.43 inch 84 mm / 3.31 inch
control form and heating and cooling selection. PT100 7A@250VV 7A@250VV If input type is selected as NTC, sensor type (V = 0, 3 or 4) must be
PT1000
They are mainly used in glass, plastic, petro-chemistry, textile, automotive and Maximum 15mm / 0.59 inch
declared in ordering information.
machine production industries. TC C NO C NO NC Supply ESM-7710
1 2 3 4 5 6 7 8 9 10
Voltage E Output-1 ESM-7710
SPECIFICATIONS Switch
INPUT Temperature L N 230VV 1 Relay Output(7A@250VVat resistive load,1NO+1NC)
Thermoresistance(RTD): 2 or 3-wire PT100, PT1000 (IEC 751) (ITS90) ESM 7710 with SSR Outputs:
Measurement Range: It is in ordering information 00 None SET
c Y CAT II
P
c
ESM-7710 : 14 mm Red 3 digits LED Display PT100 7A@250VV 7A@250VV Before beginning installation of this product, please read
PT1000
ESM-9910 : 20 mm Red 3 digits LED Display
Supply
the instruction manual and warnings below carefully. 96mm / 3.78 inch
LED Display : TC C NO NC C NO NC 12 ± 1 mm / 0.47 inch 84 mm / 3.31 inch
Voltage
Device with 1 Output : SET(Green), OUT(Red), PROG(Red) 1 2 3 4 5 6 7 8 9 10 11 Switch
In package ,
Device with 2 Outputs : SET1(Green), SET2(Green), OUT1(Red), Temperature L N 230VV - One piece unit 2
115VV
OUT2(Red), PROG(Red) Sensor Input
24VV - Two pieces mounting clamps PANEL MOUNTING 1
(TC, PTC, NTC Output-2 Output-1 24 V W
POWER SUPPLY PT100 or PT1000) 1AVT Fuse
- One piece instruction manual
Note-1
230 V V ( ±15% ) 50/60 Hz - 3 VA ESM 9910 with SSR Outputs: A visual inspection of this product for possible damage occured during
115 V V ( ±15% ) 50/60 Hz - 3 VA shipment is recommended before installation. It is your responsibility to 1-Insert the unit in the panel
24 V V ( ±15% ) 50/60 Hz - 3 VA c Y CAT II ensure that qualified mechanical and electrical technicians install this cut-out from the front side.
24 V W ( - %15, + %10 ) 50/60 Hz - 3 VA ESM-9910 product. 2- Insert the mounting clamps
(Supply voltage must be determined in order) If there is danger of serious accident resulting from a failure or defect in to the holes that located top
PTC, NTC
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS this unit, power off the system and separate the electrical connection of and bottom sides of device and
OUTPUT-2 OUTPUT-1
Operating Temperature : 0...50°C PT100
the device from the system. screw up the fixing screws until
PT1000 SSR Driver Out SSR Driver Out
Humidity : 0-90%RH (none condensing) Max.
10mA@5V Z
Max.
10mA@5V Z
the unit completely immobile
Protection Class : IP65 at front, IP20 at rear Supply The unit is normally supplied without a power switch or a fuse. Use within the panel
TC Voltage
1 2 3 4 5 6 7 8 9 10 11 Switch
power switch and fuse as required.
DEVICE WEIGHT DIMENSION PANEL CUT-OUT Temperature L N 230VV
115VV
Be sure to use the rated power supply voltage to protect the unit against
ESM-4410 160 gr 48x48 mm, Depth:95 mm 46 x 46 mm Sensor Input
24VV damage and to prevent failure.
(TC, PTC, NTC Output-2 Output-1 24 V W
ESM-7710 210 gr 72x72 mm, Depth:95.5 mm 69 x 69 mm PT100 or PT1000) Note-1 1AVT Fuse Keep the power off until all of the wiring is completed so that electric
ESM-9910 280 gr 96x96 mm, Depth:96 mm 92 x 92 mm Note-1:Output-2 exists in only ESM-7710 and ESM-9910 Devices shock and trouble with the unit can be prevented. Introduction Brochure. ENG ESM-xx10 01 V03 10/11
Front Panel ESM-xx10 with Two Relays Entering to Programming Mode, Changing and Saving Parameters Hysteresis Parameter For Output-2
Main Operation 1 to 100 °C for TC Type Devices,
Temperature Display Adjustment of SET1 Value Screen 1 to 100 °C for PT100 (0°C , 400°C),PT1000 (-50°C , 400°C),
ESM-7710 Hysteresis for
When SET1 button is pressed
P
1.0 to 10.0 °C for PT100, Pt1000 (-19.9°C, 99.9°C),
Led indication of OUTPUT-1 is active, Main for 10 seconds PROG led Output-2
Programming mode is active, Operation starts to blink. If 1 to 100 °C for PTC (-50°C, 150°C),
°C
OUTPUT-2 is active Screen °C
programming mode entering 1.0 to 10.0 °C for PTC and NTC(-19.9°C, 99.9°C),
°C OUT1 PROG OUT2
password is different from 0 1 to 20 °C for NTC(-50°C, 100°C)
°C
OUT1 PROG OUT2 Led indication of SET1/2 value OUT1 PROG OUT2
SET1 SET2
programming mode
SET1 SET2
changing mode SET1 SET2 SET1 SET2 entering screen OUT1 PROG OUT2 Operation type selection parameter of output-1
P SET1 SET2
SET1 SET2 Press SET1
P button will be observed.
SET1
P
SET2
P SET1 SET2 Operation Type of Output-1 relay can be adjusted
P
Programming Mode
as “HEATING”. Normally energised.
Temperature Controller Entering Screen Operation Type of Output-1 relay can be adjusted
Operation Form Selection as “COOLING”. Normally de-energised.
SET1 value °C for Output-1
OUT1 PROG OUT2 Operation type selection parameter of output-2
SET1 LED lights SET1 SET2
Press button This parameter is not active in devices with one relay.
°C on SET1 SET2 for accessing to the
OUT1 PROG OUT2 P
password entering screen °C Operation Type of Output-2 relay can be adjusted
It is used for entering to SET1 value changing mode
SET1
P
SET1 SET2 OUT1 PROG OUT2 as “HEATING”. Normally energised.
and programming mode Change SET1 SET1 SET2
SET1
P
SET2
value with Password Entering Operation Type of Output-2 relay can be adjusted
SET1 SET2
Screen as “COOLING”. Normally de-energised.
SET2 It is used for entering to SET2 value changing mode and buttons P
°C
Minimum Pulling Time Parameter for Output-1
SET1 SET2
P When Output-1 is inactive this time must be expired for
Main OUT1 PROG OUT2
SET1 SET2 °C °C
SET1 SET2
SET1 SET2 OUT1 PROG OUT2 P
P
Press SET2
button OUT1 PROG OUT2
SET1 SET2
SET1 SET2
SET value
SET1 SET2 SET1 SET2 Temperature Controller
P P
SET LED lights on
°C Warranty
SET2 value
OUT PROG Hysteresis for Programming Mode EMKO Elektronik warrants that the equipment delivered is free from
SET Output-1 Accessing Password
Change SET
SET2 LED lights on defects in material and workmanship. This warranty is provided for a
°C
SET
P value with °C period of two years. The warranty period starts from the delivery date.
OUT1 PROG OUT2
and buttons SET1 SET2
OUT1 PROG OUT2 This warranty is in force if duty and responsibilities which are determined
Change SET2 °C
SET1 SET2
in warranty document and instruction manual performs by the customer
SET1 SET2 value with OUT1 PROG OUT2
P
SET1
P
SET2
SET1 SET2
completely.
and buttons
SET1
P
SET2 Maintenance
°C
If Repairs should only be performed by trained and specialized personnel.
button is pressed again, device
SET2
OUT PROG
turns to parameter beginning of
Cut power to the device before accessing internal parts.
SET
the programming mode.
Do not clean the case with hydrocarbon-based solvents (Petrol,
SET
Save SET value °C
P with button Parameters Trichlorethylene etc.). Use of these solvents can reduce the mechanical
OUT1 PROG OUT2
SET1 SET2 Minimum Set Value Parameter reliability of the device. Use a cloth dampened in ethyl alcohol or water to
Save SET2 value
Main SET1 SET2
with button
SET2
Set value can not be lower than this value. This parameter clean the external plastic case.
P
Operation value can be adjusted from minimum value of devices scale Other Information
Screen to maximum set value parameter
°C Main Producer Firm Information:
OUT PROG Operation Maximum Set Value Parameter Emko Elektronik Sanayi ve Ticaret A.Þ.
SET Screen Set value can not be greater than this value. This parameter Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA
SET
°C value can be adjusted from minimum set value to Tel : (224) 261 1900
P OUT1 PROG OUT2
maximum value of device scale Fax : (224) 261 1912
SET1 SET2
SET1 SET2
Hysteresis Parameter For Output-1
P 1 to 100 °C for TC Type Devices, Repair and maintenance service Firm information:
1 to 100 °C for PT100 (0°C , 400°C),PT1000 (-50°C , 400°C), Emko Elektronik Sanayi ve Ticaret A.Þ.
1.0 to 10.0 °C for PT100, Pt1000 (-19.9°C, 99.9°C), Demirtaþ Organize Sanayi Bölgesi Karanfil Sk. No:6 16369 BURSA
If no operation is done in programming or Set value mode for If no operation is done in programming or Set value mode for
i i
1 to 100 °C for PTC (-50°C, 150°C),
20 seconds, device turns to main operation screen 20 seconds, device turns to main operation screen Tel : (224) 261 1900
1.0 to 10.0 °C for PTC and NTC(-19.9°C, 99.9°C),
automatically. automatically. Fax : (224) 261 1912
1 to 20 °C for NTC(-50°C, 100°C)