UNDERSTANDING EXTRUSIONS: WHAT YOU NEED TO KNOW
DANNY VARLEY
NT
USAT
J
ul
MUN TSC TU east
THE PROCESS EXPLAINED
Extrusion is a technique where heated materials such as aluminium are forced through an
opening to form a shaped profile.
To produce an aluminium extrusion, an aluminium billet (a solid block/log of aluminium) is
heated to the required temperature then loaded into the container of the press, it is then then
forced through a shape created in a specially manufactured tool called a die, Once the
aluminium has been pushed through the container by the ram within the press, it will form
the extruded profile which will be the same shape as the opening in the die
The size of an extrusion is measured by the size of its cross-sectional dimension. This is it's,
BWC Q
PROFILESSeveral factors dictate as to what size press the profile can
be extruded on. Overall size is one, but also there can be
multiple cavities within one die. There are significant forces
generated when pushing a billet through the die, so it may be |
necessary to create more cavities within the die, therefore |
increasing the overall weight/mtr across the die. This enables \
the aluminium to flow through the die without too much
negative pressure. a
In simple terms it is a bit like holding your thumb on the end of a toothpaste tube and trying
to squeeze it out. It will not come out, but if you move your thumb slightly, the toothpaste will
flow more freely.
The variety of shapes which can be extruded is almost endless, however there are factors
which put limits to what can be achieved. The factors which need to be considered include;
* Size
* Shape
* Alloy - Chemical composition of other elements added to pure aluminium to enhance
its properties such as strength, etc.
~ Area of the billet/area of the shape.
* Extrusion Rat
* Tongue Ratio - Width of the gap vs. its depth.
* Tolerance - Limits of variation in which a part or product can be produced to
* Finish ~ Treatments used to enhance the end look & feel of the profile.
* Factor - Perimeter of Shape/ Weight per metre.
A profile which is designed beyond these limits may possibly not be extruded successfull.
All the above factors are interrelated in the extrusion process along with extrusion speed,
temperature of billet, extrusion pressure and the alloy being used for extrusion.
These will all contribute to and determine the cost of your extrusion.
The speed of an extrusion varies depending on the temperature, pressure and alloy being
used for the shape being extruded. (See selecting the right aluminium alloy for more
information.)
The lower the temperature, the higher the pressure that's required. Lower temperature
extrusions typically produce shapes that have a better surface quality and dimensions which
are more accurate
profile is unsuccessful.EXTRUSION RATIO: AREA OF THE BILLET/AREA OF THE
SHAPE.
Extrusion (A;) Extrusion (A,)
Work Billet (Ao)
The extrusion ratio is the ratio of the area of the work billets cross section (Ao) to that of the
extrusion's cross section (Af). The extrusion ratio, or reduction ratio, can be expressed as
(Ao/Af)
There is a general rule that if an alloy has higher mechanical properties the extrusion rate
needs to be lower.
The extrusion ratio will be a clear indication to the amount of mechanical working that will
occur as the shape is being extruded.
If the extrusion ratio of a profile section is low, then parts of the shape will have less
mechanical work performed on it, especially the shapes largest mass of metal.
‘Shapes with an extrusion ratio of less than 10:1 are not to guaranteed to mechanical
properties.
When the extrusion ratio is higher, greater pressure will be needed to force the metal through
the smaller opening in the die, this means that intense mechanical working will occur.
Acceptable Extrusion Ratios Range;
Hard Alloys: 10:1 - 35:1
Soft Alloys: 10.1 -100:1
The above ranges all depend on the shape of the extrusionFACTOR: PERIMETER OF SHAPE/ WEIGHT PER METRE.
Performance is also defined by the parts difficulty factor.
The weight per metre will determine the size of the press you will need to extrude your
profile but again this all depends on a number of considerations;
The size of the press will determine how large an extrusion profile can be produced.
Usually, the lighter a section is, the smaller the press you will need to extrude it unless you're
extruding a large, hollow shape with thin walls. The higher the factor is, the harder itis to
extrude,
TONGUE RATIO: WIDTH OF THE GAP VS. LENGTH OR HEIGHT.
Easy / 3:1 Ratio Challenging / 5:1 Ratio Extremely Dfficult / 8:1 Ratio
owl
The parts Tongue ratio will also be will a factor to the success of your parts performance.
&
Tongue ratios can be worked out by doing the following; square the smallest opening to the
void, calculate the total area of the shape, and then divide the opening squared by the area.
The higher the tongue ratio the more difficult it is to extrude.
LEARN MORE...
You can learn more about the factors involved in the extrusion process in our Aluminium
Ge BWC
atumintum | [ acavemy[| RELATED PosTS
18-NOV-2020 16:50:37
BENEFITS OF USING ALUMINIUM
18-Nov-2020 16:59:36
PLASTIC EXTRUSION 101
18-NOV-2020 17:08:58
BENEFITS OF USING PLASTIC
ABOUT US
lished in 1999, UK b:
manufacturing gr ponent design and
supply. Special
sts in aluminium extrusion, plastic extrusion & injection moulding,
LATEST POSTS
Plasti
Extrusion Materials
Cookie Policy
SOCIALS