Professional Documents
Culture Documents
WIT-PE 500
Approved for:
Concrete C20/25 to C50/60, cracked
Suitable for:
Concrete C12/15, Natural stone with dense structure
Applications
WIT-PE 500 M
68
Basic loading data (for a single anchor)
All data in this section applies to: • Concrete C 20/25, fck,cube = 25 N/mm²,
• Correct setting (See Installation instruction). Concrete C 50/60, fck,cube = 60 N/mm².
• No edge distance and spacing influence. • Temperate range I (min. base material temperature
• Base material thickness, as specified in the table. -40°C, max. long term/short term base material
• Embedment depth, as specified in the table. temperature: +24°C/40°C).
• Anchor material, as specified in the tables, • Dry or wet conditions of drill hole, hammer drilling
steel grade 5.8. • Installation temperature range +5°C to +40°C.
Characteristic resistance
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Effective anchorage depth hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
Non-cracked concrete
Tensile C20/25 NRk [kN] 18.3 29.0 42.1 70.6 111.9 153.7 187.8 224.0 262.4 302.7 344.9
C50/60 NRk [kN] 18.3 29.0 42.1 77.6 123.1 169.0 206.5 246.5 288.6 333.0 379.4
Shear ≥ C20/25 VRk [kN] 9.2 14.5 21.1 39.2 61.2 88.1 114.8 140.1 173.4 204.2 243.9
Cracked concrete
Tensile C20/25 NRk [kN] 31.1 40.8 64.1 87.1 112.0 140.0
C50/60 NRk [kN] 34.2 44.9 70.5 95.8 123.2 154.0
WIT-PE 500 M
Shear ≥ C20/25 VRk [kN] 21.1 39.2 61.2 88.1 114.8 140.1
Design resistance
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Effective anchorage depth hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
Non-cracked concrete
Tensile C20/25 NRd [kN] 12.2 19.3 28.1 39.2 53.3 73.2 89.4 106.7 125.0 144.2 164.3
C50/60 NRd [kN] 12.2 19.3 28.1 43.1 58.6 80.5 98.4 117.4 137.5 158.6 180.7
Shear ≥ C20/25 VRd [kN] 7.4 11.6 16.9 31.4 49.0 70.5 91.8 112.1 138.7 163.3 195.2
Cracked concrete
Tensile C20/25 NRd [kN] 17.3 22.7 30.5 41.5 53.3 66.6
C50/60 NRd [kN] 19.0 25.0 33.6 45.6 58.6 73.3
Shear ≥ C20/25 VRd [kN] 16.9 31.4 49.0 70.5 91.8 112.1
69
WIT-PE 500 WITH THREADED ROD (METRIC)
Recommended / Allowable loads1)
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Effective anchorage depth hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
Non-cracked concrete
Tensile C20/25 Nrec [kN] 8.7 13.8 20.1 28.0 38.1 52.3 63.9 76.2 89.3 103.0 117.3
C50/60 Nrec [kN] 8.7 13.8 20.1 30.8 41.9 57.5 70.3 83.8 98.2 113.3 129.1
Shear ≥ C20/25 Vrec [kN] 5.3 8.3 12.1 22.4 35.0 50.3 65.6 80.1 99.1 116.7 139.4
Cracked concrete
Tensile C20/25 Nrec [kN] 12.3 16.2 21.8 29.6 38.1 47.6
C50/60 Nrec [kN] 13.6 17.8 24.0 32.6 41.9 52.4
Shear ≥ C20/25 Vrec [kN] 12.1 22.4 35.0 50.3 65.6 80.1
1)
Material safety factor yM and safety factor for action y L = 1.4 are included. The material safety factor depends on the failure mode.
WIT-PE 500 M
70
Design Method (simplified)
Simplified version of the design method according ETAG 001, TR 029. Design resistance
according data given in ETA-09/0040, issue 2013-06-14:
• Influence of concrete strength.
• Influence of edge distance.
• Influence of spacing.
• Valid for a group of anchors. (The influencing factors must then be considered for each edge distance and spacing.
The calculated design loads are then on the save side. They will be lower than the exact values according
ETAG 001, Annex C. To avoid this, it is recommended to use the anchor design software of Würth).
• The design method is based on the following simplification: No different loads are acting on individual anchors
(no eccentricity).
• Temperate range I (min. base material temperature -40°C, max. long term/short term base material temperature:
+24°C/40°C).
• Dry or wet conditions of drill hole, hammer drilling.
• Installation temperature range +5°C to +40°C.
• M33, M36, M39 not part of ETA, data based on in-house testing according to guideline.
Tension loading
The decisive design resistance in tension is the lowest value of the following failure modes:
Steel failure:
WIT-PE 500 M
Concrete cone failure:
steel grade Thread M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
size
5.8 NRd,s [kN] 12.2 19.3 28.1 52.2 81.6 117.5 153.1 186.9 231.2 272.2 325.3
8.8 NRd,s [kN] 19.5 30.9 44.9 83.6 130.6 188.0 245.0 299.0 369.9 435.6 520.4
10.9 NRd,s [kN] 26.1 41.4 60.2 111.9 174.9 251.8 328.1 400.4 495.4 583.4 697.0
A4-70 NRd,s [kN] 13.7 21.7 31.5 58.6 91.6 132.2 172.3 210.2 260.1 306.3 365.9
71
WIT-PE 500 WITH THREADED ROD (METRIC)
Design combined pull-out and concrete cone resistance of a single anchor
Basic design combined pull-out and concrete cone resistance of a single anchor
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
Non-cracked concrete
N0Rd,p [kN] 16.8 23.6 34.6 48.9 66.1 90.5 116.3 145.4 162.9 195.5 231.0
Cracked concrete
N0Rd,p [kN] 17.3 22.7 30.5 41.5 53.3 66.6
1)
strength at 28days of 150mm diameter by 300mm cylinders.
2)
strength at 28days of 150mm cubes.
72
Characteristic edge distance ccr,p and spacing scr,p
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
scr,p [mm] 226 270 330 375 510 607 683 759 799 872 945
ccr,p [mm] 113 135 165 188 255 304 342 379 400 436 472
Number of
fixing per s/scr,p1) 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
direction
2 fsx,p, fsy,p 0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
3 fsx,p, fsy,p 0.40 0.43 0.47 0.50 0.53 0.57 0.60 0.63 0.67 0.70 0.73 0.77 0.80 0.83 0.87 0.90 0.93 0.97 1.00
4 fsx,p, fsy,p 0.33 0.36 0.40 0.44 0.48 0.51 0.55 0.59 0.63 0.66 0.70 0.74 0.78 0.81 0.85 0.89 0.93 0.96 1.00
5 fsx,p, fsy,p 0.28 0.32 0.36 0.40 0.44 0.48 0.52 0.56 0.60 0.64 0.68 0.72 0.76 0.80 0.84 0.88 0.92 0.96 1.00
1)
Choose always the lowest value of the spacing s, when there are different spacings in one row.
WIT-PE 500 M
;
c/ccr,p 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
fcx,1,p 0.73 0.75 0.76 0.78 0.79 0.81 0.82 0.84 0.85 0.87 0.88 0.90 0.91 0.93 0.94 0.96 0.97 0.99 1.00
fcx,2,p
0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
fcy,p
73
WIT-PE 500 WITH THREADED ROD (METRIC)
Basic design concrete cone resistance of a single anchor
Anchor type: WIT-PE 500 M
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
Non-cracked concrete
N0Rd,c [kN] 20.1 24.0 32.4 39.2 53.3 73.2 89.4 106.7 125.0 144.2 164.3
Cracked concrete
N0Rd,c [kN] 14.3 17.1 23.1 28.0 38.1 52.3 63.9 76.2 89.3 103.0 117.3
1)
strength at 28days of 150mm diameter by 300mm cylinders.
2)
strength at 28days of 150mm cubes.
WIT-PE 500 M
74
Concrete cone failure
Characteristic edge distance ccr,N and spacing scr,N
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
scr,N [mm] 240 270 330 375 510 630 720 810 900 990 1080
ccr,N [mm] 120 135 165 188 255 315 360 405 450 495 540
Above characteristic spacing and edge distances are given for the typical effective anchorage depth. Calculating for
smaller depths is leading to conservative load capacities. For calculation with bigger depths use the following:
and .
Number of
fixing per s/scr,N1) 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
direction
2 fsx, fsy 0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
3 fsx, fsy 0.40 0.43 0.47 0.50 0.53 0.57 0.60 0.63 0.67 0.70 0.73 0.77 0.80 0.83 0.87 0.90 0.93 0.97 1.00
4 fsx, fsy 0.33 0.36 0.40 0.44 0.48 0.51 0.55 0.59 0.63 0.66 0.70 0.74 0.78 0.81 0.85 0.89 0.93 0.96 1.00
5 fsx, fsy 0.28 0.32 0.36 0.40 0.44 0.48 0.52 0.56 0.60 0.64 0.68 0.72 0.76 0.80 0.84 0.88 0.92 0.96 1.00
WIT-PE 500 M
1)
Choose always the lowest value of the spacing s, when there are different spacings in one row.
c/ccr,N 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
fcx,1 0.73 0.75 0.76 0.78 0.79 0.81 0.82 0.84 0.85 0.87 0.88 0.90 0.91 0.93 0.94 0.96 0.97 0.99 1.00
fcx,2
0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
fcy
75
WIT-PE 500 WITH THREADED ROD (METRIC)
Concrete splitting failure
Characteristic edge distance ccr,sp and spacing scr,sp
Anchor type: WIT-PE 500 M
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
scr,sp [mm] 360 420 528 600 816 1008 1152 1296 1440 1584 1728
ccr,sp [mm] 180 210 264 300 408 504 576 648 720 792 864
hmin [mm] 110 120 134 157 210 258 294 330 366 402 438
Above characteristic spacing and edge distances are given for the typical effective anchorage depth. Calculating for
smaller depths is leading to conservative load capacities. For calculation with bigger depths use the following:
and
Number of
fixing per s/scr,sp1) 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
WIT-PE 500 M
direction
2 fsx,sp, fsy,sp 0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
3 fsx,sp, fsy,sp 0.40 0.43 0.47 0.50 0.53 0.57 0.60 0.63 0.67 0.70 0.73 0.77 0.80 0.83 0.87 0.90 0.93 0.97 1.00
4 fsx,sp, fsy,sp 0.33 0.36 0.40 0.44 0.48 0.51 0.55 0.59 0.63 0.66 0.70 0.74 0.78 0.81 0.85 0.89 0.93 0.96 1.00
5 fsx,sp, fsy,sp 0.28 0.32 0.36 0.40 0.44 0.48 0.52 0.56 0.60 0.64 0.68 0.72 0.76 0.80 0.84 0.88 0.92 0.96 1.00
1)
Choose always the lowest value of the spacing s, when there are different spacings in one row.
c/ccr,sp 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 ≥ 1.0
fcx,1, sp 0.73 0.75 0.76 0.78 0.79 0.81 0.82 0.84 0.85 0.87 0.88 0.90 0.91 0.93 0.94 0.96 0.97 0.99 1.00
fcx,2, sp
0.55 0.58 0.60 0.63 0.65 0.68 0.70 0.73 0.75 0.78 0.80 0.83 0.85 0.88 0.90 0.93 0.95 0.98 1.00
fcy, sp
76
Concrete splitting failure - Influence of concrete member thickness
h/hmin 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 ≥2.90
fh 1.00 1.07 1.13 1.19 1.25 1.31 1.37 1.42 1.48 1.53 1.59 1.64 1.69 1.74 1.79 1.84 1.89 1.94 1.99 2.00
Shear loading
The decisive design resistance in shear is the lowest value of the following failure modes:
Steel failure:
WIT-PE 500 M
10.9 VRd,s [kN] 12.2 19.3 28.1 52.2 81.6 117.5 153.1 186.9 231.2 272.2 325.3
A4-70 VRd,s [kN] 8.3 12.8 19.2 35.3 55.1 79.5 103.4 126.1 156.1 183.8 219.5
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,typ [mm] 80 90 110 125 170 210 240 270 300 330 360
k [-] 2 2 2 2 2 2 2 2 2 2 2
77
WIT-PE 500 WITH THREADED ROD (METRIC)
Design concrete edge resistance
Verification of concrete edge failure may be omitted for single fasteners and groups with an edge distance in all
directions . For anchorages with more than one edge, the resistance for all edges shall be
calculated. The smallest value should be used in the verification.
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Non-cracked concrete
V0Rd,c [kN] 5.2 7.5 10.1 16.4 24.3 33.7 40.3 46.3 52.6 59.1 65.7
Cracked concrete
V0Rd,c [kN] 3.7 5.3 7.1 11.6 17.1 23.7 28.3 32.6 37.0 41.6 46.3
1)
strength at 28days of 150mm diameter by 300mm cylinders.
2)
strength at 28days of 150mm cubes.
hef /d 4 5 6 7 8 9 10 11 ≥ 12
fhef,V 0.87 0.91 0.94 0.97 1.00 1.02 1.05 1.07 1.08
78
Influence of load direction
α1) 0 10 20 30 40 50 60 70 80 90
fα,V 1.00 1.01 1.05 1.11 1.20 1.34 1.51 1.72 1.92 2.00
1)
For α ≥ 90° the component of the shear load acting away from the edge may be neglected and the verification may
be done with component acting parallel to the edge only.
Influence of spacing
In groups loaded perpendicular to the edge only two adjacent anchors closest and parallel to the edge carry the load.
The smallest spacing should be used for the verification.
s/c11) 0.50 0.60 0.70 0.80 0.90 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00
fs,V 1.17 1.20 1.23 1.27 1.30 1.33 1.40 1.47 1.53 1.60 1.67 1.73 1.80 1.87 1.93 2.00
1)
Choose always the lowest value of the spacing s, when there are different spacings in the row closest to the edge.
WIT-PE 500 M
c2/c11) 1.00 1.10 1.20 1.30 1.40 1.50
fc,V 0.75 0.80 0.85 0.90 0.95 1.00
1)
Distance to the second edge: c1 ≤ c2.
h/c1 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 1.10 1.20 1.30 1.40 ≥ 1.50
fh,V 0.26 0.37 0.45 0.52 0.58 0.63 0.68 0.73 0.77 0.82 0.86 0.89 0.93 0.97 1.00
79
WIT-PE 500 WITH THREADED ROD (METRIC)
Structural Verification
Tension
Shear
80
Service temperature
Temperature range Base material Maximum long term base Maximum short term base
temperature material temperature material temperature
Temperature range I -40 °C to +40 °C +24 °C +40 °C
Temperature range II -40 °C to +60 °C +43 °C +60 °C
Temperature range III -40 °C to +72 °C +43 °C +72 ° C
Non-cracked concrete
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Design bond strength according to ETA-09/0040 / dry and wet concrete / hammer drilling
Temperature range I τRd,ucr [N/mm2] 8.3 8.3 8.3 7.8 6.2 5.7 5.7 5.7 5.2 5.2 5.2
Temperature range II τRd,ucr [N/mm ]
2
5.3 5.3 5.0 4.7 3.8 3.6 3.6 3.6 3.3 3.3 3.3
Temperature range III τRd,ucr [N/mm2] 4.7 4.7 4.4 4.2 3.3 3.3 3.1 3.1 2.9 2.9 2.9
Design bond strength according to ETA-09/0040 / flooded concrete / hammer drilling
Temperature range I τRd,ucr [N/mm2] 7.1 6.7 6.2 4.8 4.5 4.0 3.6 3.3
Temperature range II τRd,ucr [N/mm ]
2
4.5 4.5 4.3 4.0 3.6 3.3 3.1 2.9
Temperature range III τRd,ucr [N/mm2] 4.0 4.0 3.8 3.6 3.3 2.9 2.6 2.6
Design bond strength according to ETA-11/0398 / dry and wet concrete / diamond drilling
WIT-PE 500 M
Temperature range I τRd,ucr [N/mm2] 7.3 5.6 5.6 5.3 5.0
Temperature range II τRd,ucr [N/mm ]
2
4.7 3.6 3.3 3.3 3.1
Temperature range III τRd,ucr [N/mm ]
2
4.0 3.3 3.1 2.8 2.8
Design bond strength according to ETA-11/0398 / flooded concrete / diamond drilling
Temperature range I τRd,ucr [N/mm2] 6.0 5.6 5.3 5.3 4.7
Temperature range II τRd,ucr [N/mm2] 3.7 3.6 3.3 3.3 3.1
Temperature range III τRd,ucr [N/mm ]
2
3.3 3.3 2.8 2.8 2.8
Cracked concrete
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Design bond strength according to ETA-09/0040 / dry and wet concrete / hammer drilling
Temperature range I τRd,cr [N/mm2] 4.2 3.6 2.9 2.6 2.6 2.6
Temperature range II τRd,cr [N/mm ]
2
2.5 2.2 1.7 1.7 1.7 1.7
Temperature range III τRd,cr [N/mm2] 2.2 1.9 1.4 1.4 1.4 1.4
Design bond strength according to ETA-09/0040 / flooded concrete / hammer drilling
Temperature range I τRd,cr [N/mm2] 3.6 2.9 2.4 2.1 1.9 1.9
Temperature range II τRd,cr [N/mm ]
2
2.1 1.9 1.7 1.7 1.7 1.7
Temperature range III τRd,cr [N/mm2] 1.9 1.7 1.4 1.4 1.4 1.4
81
WIT-PE 500 WITH THREADED ROD (METRIC)
Reduction factor for different use categories
Non-cracked concrete
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Reduction factor strength according to ETA-09/0040 / dry and wet concrete / hammer drilling
Temperature range I fτ.red 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00
Temperature range II fτ.red 0.63 0.63 0.60 0.61 0.62 0.63 0.63 0.63 0.64 0.64 0.64
Temperature range III fτ.red 0.57 0.57 0.53 0.54 0.54 0.58 0.54 0.54 0.55 0.55 0.55
Reduction factor according to ETA-09/0040 / flooded concrete / hammer drilling
Temperature range I fτ.red 0.86 0.80 0.74 0.61 0.73 0.71 0.63 0.58
Temperature range II fτ.red 0.54 0.54 0.51 0.52 0.58 0.58 0.54 0.50
Temperature range III fτ.red 0.49 0.49 0.46 0.46 0.54 0.50 0.46 0.46
Reduction factor according to ETA-11/0398 / dry and wet concrete / diamond drilling
Temperature range I fτ.red 0.88 0.67 0.71 0.85 0.88
Temperature range II fτ.red 0.56 0.43 0.43 0.54 0.53
Temperature range III fτ.red 0.48 0.40 0.39 0.45 0.49
Reduction factor according to ETA-11/0398 / flooded concrete / diamond drilling
Temperature range I fτ.red 0.72 0.67 0.68 0.85 0.83
Temperature range II
WIT-PE 500 M
Cracked concrete
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Reduction factor according to ETA-09/0040 / dry and wet concrete / hammer drilling
Temperature range I fτ.red 1.00 1.00 1.00 1.00 1.00 1.00
Temperature range II fτ.red 0.60 0.62 0.58 0.64 0.64 0.64
Temperature range III fτ.red 0.53 0.54 0.50 0.55 0.55 0.55
Reduction factor according to ETA-09/0040 / flooded concrete / hammer drilling
Temperature range I fτ.red 0.86 0.79 0.83 0.82 0.73 0.73
Temperature range II fτ.red 0.51 0.53 0.58 0.64 0.64 0.64
Temperature range III fτ.red 0.46 0.46 0.50 0.55 0.55 0.55
82
Anchor characteristics
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
hef,min [mm] 60 60 70 80 90 96 108 120 132 144 156
Effective anchorage depth
hef,max [mm] 96 120 144 192 240 288 324 360 396 432 468
Nominal drill hole
d0 [mm] 10 12 14 18 24 28 32 35 37 42 46
diameter
Drill depth h0 / h1 [mm] = hef
Clearance-hole in fixture
df [mm] 9 12 14 18 22 26 30 33 36 39 42
to be attached
Wrench size SW [mm] 13 17 19 24 30 36 41 46 50 55 60
Required torque Tinst [Nm] 10 20 40 80 120 160 180 200 350 500 700
Min. thickness of
hmin [mm] = hef + 30mm ≥ 100mm = hef + 2d0
concrete member
Minimum spacing smin [mm] 40 50 60 80 100 120 135 150 165 180 195
Minimum edge distances cmin [mm] 40 50 60 80 100 120 135 150 165 180 195
WIT-PE 500 M
df
d0
83
WIT-PE 500 WITH THREADED ROD (METRIC)
Mechanical characteristics
steel grade Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Stressed As [mm²] 37 58 84 157 245 352 459 561 694 817 976
cross section
Section Modulus W [mm³] 31 62 109 277 540 933 1389 1872 2576 3292 4299
Yield strength fy [N/mm2] 400 400 400 400 400 400 400 400 400 400 400
Tensile strength fu [N/mm ] 2
500 500 500 500 500 500 500 500 500 500 500
5.8
Design bending
M0Rd,s [Nm] 15 30 52 133 259 448 667 899 1237 1580 2064
moment
Yield strength fy [N/mm2] 640 640 640 640 640 640 640 640 640 640 640
Tensile strength fu [N/mm ] 2
800 800 800 800 800 800 800 800 800 800 800
8.8
Design bending
M0Rd,s [Nm] 24 48 84 212 415 717 1067 1438 1979 2528 3302
moment
Yield strength fy [N/mm2] 900 900 900 900 900 900 900 900 900 900 900
Tensile strength fu [N/mm ] 1000 1000 1000 1000 1000 1000 1000
2
1000 1000 1000 1000
10.9
Design bending
M0Rd,s [Nm] 25 50 87 221 432 747 1111 1498 2061 2634 3439
moment
Yield strength fy [N/mm2] 450 450 450 450 450 450 450 450 450 450 450
Tensile strength fu [N/mm ] 2
700 700 700 700 700 700 700 700 700 700 700
A4-70
Design bending
M0Rd,s [Nm] 17 34 59 149 292 504 750 1011 1391 1778 2322
WIT-PE 500 M
moment
84
Material specification of anchor
WIT-PE 500 M
≤ M24: Property class 70 EN ISO 3506
Material 1.4529 / 1.4565, EN 10088,
2 Hexagon nut, EN 24032 > M24: Property class 50 (for class 50 rod)EN ISO 3506
≤ M24: Property class 70 (for class 70 rod)EN ISO 3506
Washer, EN ISO 7089,
3 Material 1.4529 or 1.4565, EN 10088
EN ISO 7093 or EN ISO 7094
85
WIT-PE 500 WITH THREADED ROD (METRIC)
Properties of adhesive
Stability
UV-resistance (sunlight) resistant
Temperature resistance 72 °C
Water resistancy resistant
Water absorption ASTM D 570 0.109 %
Cleaning agents 1% tenside solution: no effects
Physical properties
Flexural strength DIN EN 196-1 after 24 hours: 42 N/mm2
Modulus of Elasticity (Young's UNI EN ISO 178 after 24 hours: 4.11 GPa
Flexural Properties Modulus)
Flexural stress at break UNI EN ISO 178 after 24 hours: 86 MPa
Flexural strain at break UNI EN ISO 178 after 24 hours: 2.0 %
Compressive strength DIN EN 196-1 after 24 hours: ≥ 120 N/mm2
after 7 days: 169 MPa
Compressive strength UNI EN ISO 604
after 2 days: 166 MPa
Compressive Properties
Modulus of Elasticity ASTM D 695 after 24 hours: 5.97 GPa
Yield stress ASTM D 695 after 24 hours: 5129 GPa
Deformation beyond yield point ASTM D 695 3.6 %
WIT-PE 500 M
86
Working time and curing time
Temperature Gelling - working time Minimum Curing time Minimum Curing time
of Concrete in dry concrete in wet concrete
5°C to 9°C 60 min 72 h 142 h
10°C to 19°C 45 min 45 h 90 h
20°C to 29°C 30 min 10 h 20 h
30°C to 39°C 20 min 6 h 12 h
≥ 40°C 12 min 4 h 8h
Filling Quantity
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
WIT-PE 500 M
87
WIT-PE 500 WITH THREADED ROD (METRIC)
Installation instruction
Installation Control
Drill hole to the required embedment depth with a hammer Working length of drill bit must be
drill set in rotation-hammer mode using an appropriately bigger than the given drill hole
sized carbide drill bit.(for drill bit diameter and drill hole depth.
depth (see table „Anchor characteristics“)
Blow out at least 2x from the back of the bore hole until The compressed air without oil.
return air stream is free of noticeable dust.
If the back of the bore hole is not reached an extension
shall be used.
The hand-pump can be used for anchor sizes up to bore
hole diameter 20 mm. For bore holes larger than 20 mm
WIT-PE 500 M
Brush 2x with the specified brush size by inserting the The brush must produce natural
brush to the back of the hole in a twisting motion and resistance as it enters the drill hole -
removing it. if not, the brush is too small and
must be replaced with the proper
brush diameter (use the brush
diameter gauge).
or Blow out at least 2x from the back of the bore hole until
return air stream is free of noticeable dust.
If the back of the bore hole is not reached an extension
shall be used.
The hand-pump can be used for anchor sizes up to bore
hole diameter 20 mm. For bore holes larger than 20 mm
or deeper 240 mm, compressed air (min. 6 bar) must be
used.
Prior to inserting the anchor rod into the filled bore hole, Before use, verify that the anchor
the position of the embedment depth shall be marked on element is dry and free of oil and
the anchor rods. other contaminants.
88
Installation Control
Tightly attach mixing nozzle to cartridge. Only use mixing nozzle and
Place the cartridge into dispensing gun. dispensing gun of the system.
Do not modify the mixing nozzle.
Inject the adhesive starting at the back of the hole, slowly Marking the mixing nozzle makes
withdrawing the mixer with each trigger pull. it easier to fill every hole with the
Fill holes approximately 2/3 full, or as required to ensure same volume.
that the annular gap between the anchor and the concrete
is completely filled with adhesive along the embedment
length.
For embedment larger than 190mm an extension nozzle
shall be used.
For overhead and horizontal installation in bore holes
larger than ∅ 20mm a injection adapter and extension
nozzle shall be used.
Press the marked anchor element down to the bottom of If these requirements (excess mortar
WIT-PE 500 M
the hole, turning it slightly while doing so. and the embedment depth) are not
After inserting the anchor element, excess mortar must maintained, the application has to
emerge from the annular gap. be renewed.
For overhead installation fix
embedded part (e.g.wedges).
After required curing time, the anchor element can be Check the max. torque by using a
loaded. calibrated torque wrench.
The applied installation torque shall not exceed. (see table
„Anchor characteristic“)
89
WIT-PE 500 WITH THREADED ROD (METRIC)
Accessoires
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Required torque Tinst [Nm] 10 20 40 80 120 160 180 200 350 500 700
Hammer Drills
Drill Bits
Brush
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Blow-out (manual)
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
90
Compressed-air cleaning
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
Injecting
Thread size M8 M10 M12 M16 M20 M24 M27 M30 M33 M36 M39
WIT-PE 500 M
91
WIT-PE 500 WITH THREADED ROD (METRIC)
Chemical resistance
92
93