You are on page 1of 2

MITSUMI

Compact, AM/FM Automotive Electronic Tuner


FAE372-A02/E02/J01
AM/FM Electronic Tuners

FEATURES
1. Car AM/FM all-in-one electronic tuner with
built-in PLL.
2. FM three gang tuning, F.E+IF+NC+MPX
structure.
3. LW~MW receiving without band switching
circuit, due to the AM double conversion
method.
4. With IF selectivity switching function.
Improved reception performance relative to
adjacent station interference.
5. Good radiation due to built-in PLL.
6. FM-DET pin allows use in sets with RDS
(European) function.
7. Ideal for mid-and high quality car stereo
systems.
8. Supports various bands (normal overseas,
North American, European).

SPECIFICATIONS
Item FAE372-A02/E02/J01 FAE372-A02/E02/J01 FAE372-E01
FM MW LW
MPX VCC 8.0 ± 0.5V 8.0 ± 0.5V 8.0 ± 0.5V
Supply Voltage LPF VCC 9.0 ± 0.5V 9.0 ± 0.5V 9.0 ± 0.5V
PLL VDD 5.0 ± 0.5V 5.0 ± 0.5V 5.0 ± 0.5V
Current Consumption 170mA max. 170mA max. 170mA max.
A02 : 530~1710kHz
A02/E02 : 87.5~108MHz A02 : —— J01: ——
Tuning Range E02 : 522~162kHz
J01 : 76.0~90MHz E02 : 153~279kHz
J01 : 522~1629kHz
Input Impedance 75Ω unbalanced ——— ———
1st IF=10.7MHz 1st IF=10.7MHz
Center IF 10.7MHz
2nd IF=450kHz 2nd IF=450kHz
10dBµ max. (5.0dBµ typ.) 37dBµ max. (33dBµ typ.) 39dBµ max. (35dBµ typ.)
Usable Sensitivity
S/N 30dB S/N 20dB S/N 20dB
Image Rejection 43dB min. 45dB min. 55dB min.
IF Rejection 70dB min. 40dB min. 38dB min.
54dB min. (mono) 44dB min. 44dB min.
S/N Ratio
(1kHz, 22.5kHz dev.) (400Hz, 30% mod.) (400Hz, 30% mod.)
100mV/rms typ. 100mV/rms typ. 100mV/rms typ.
Output Level
(1kHz, 22.5kHz dev.) (400Hz, 30% mod.) (400Hz, 30% mod.)
23dB min.
Separation ——— ———
(Input 60dB, 40kHz dev.+Pilot 10%)

*Note Specifications subject to change without notice.

This datasheet has been downloaded from http://www.digchip.com at this page


MITSUMI
Compact, AM/FM Automotive Electronic Tuner

DIMENSIONS
S. Meter

15 max.

67.5 max. (typ.14)

42.2 max.
(typ. 41.4)
MITSUMI

3.6
Sepa.
1 1112 22 4
0.4
25 5 25
3.6

4.6
64.2
4.5
4.65
4.25

9.35

1 1
64.6
4.5

4.5

10 2.5=25 5 10 2.5=25

EXTERNAL TERMINALS 4.5


1. GND 12. SD/ST-IND
2. AM ANT 13. PLL VDD
3. AM VCC 14. CE ø1 22
4. FM VCC 15. DI
4.8
4.8

5. FM ANT 16. CL
6. GND 17. DO
7. PLL VSS 18. MRC SENSOR
Terminal hole layout
8. CF BW Monitor 19. FM/AM S.METER
9. LPF VCC 20. MPX VCC (DIP Side)
10. Lch 21. MUTE DRIVE Reference only
11. Rch 22. FM/AM DET * S=1/1

Unit: mm
General Tolerance: ±0.2

You might also like