Professional Documents
Culture Documents
,Ltd
The downhole motor is suitable for high-temperature, high oil base mud system. In the
conditions of less than 180°C and high oil, specially formulated stator elastomer owns high
retention rates of strong force strength, tear strength and other properties. The oil-resistant
elastomer with reasonable magnitude of interference has better using effect in the
high-temperature, high oil base mud.
Corrosion-resistance:
After corrosion spraying to form special coating, the rotor is better corrosion, erosion and
abrasion-resistant. And downhole motor is suitable for long time in the corrosive fluid.
Air Drilling:
Air drilling can protect reservoir well, improve rate of penetration, significantly shorten drilling
period, take precaution against mud loss and borehole collapse, now is gradually widely used. Air
drilling downhole motor is driven by gas, foam and other compressible fluids, provide power for the
downhole and drives bit to penetrate rock. Air drilling downhole motor has higher technical
requirements of the assembly structure,linear design of the motor stator andoperation specification.
-1-
BRJ
Technical parameters
W.P. Max.
Rotary Output Max.
OD Con. Flow Rate Pre. W.P.
Speed Loss Torque Torque
Lobe Stage Loss
4 3/4 3 1/2REG
5:6 5 171-342 140-280 585 1730 824 2442 10803
3 1/2REG
4 1/2REG
6 3/4 7:8 5 312-625 84-168 585 5293 824 7476 22000
4 1/2REG
5 1/2REG
8 7:8 5 295-650 75-150 585 5324 824 7520 34100
5 1/2REG
6 5/8REG
9 5/8 7:8 5 600-1200 68-135 585 11760 824 17720 48400
6 5/8REG
11 7 5/8REG
3:4 4 750-1500 97-196 466 8731 655 12300 67500
1/4 7 5/8REG
We offer several options for IBS, in both alloy steel and non-magnet materials:
Hardfacing type;
Fixed diameter hole openers are used for expanding the drilled hole. The
cutters are manufactured under the severe quality control. All our hole
openers are field maintainable, with easy assembly and disassembly. They
are all equipped with 3 or 4 cutters, as well as mud nozzles precisely located
to clean the cutters and the hole simultaneously.
They are used for the following purposes:
1. When drilling of the big hole is not possible because of the rig
capacity.
2. When a satisfied penetration rate is not obtained in case of the big
-3-
BRJ
hole drilling, it is used after drilling with smaller bit.
3. When the hole direction must be controlled.
When ordering please specify:
Hole size to desire;
Pilot hole size;
Top and bottom connections;
Fishing neck and bottom neck O.D and length;
Type of cutters.
Technical Parameters
Fishing Top Bottom
Product Hole open Qty of Min. pilot Overall
model neck I.D connection connection
code diameter cutters hole length
diameter (pin) (box)
-4-
BRJ
Model “TLQ” Hydraulic thruster can change the pressure drop of bit nozzle or down-hole motor
into drill pressure, not only can solve the problems that drill pressure is difficult for appling in
directional well, horizontal well, but also has the acting of heave compensator in off-land drilling.
And it can be capable of improving the stressed state of drilling tool and reducing fatigue damage of
drilling tool, and also increasing the drilling rate.
Technical parameters
Piston
O.D I.D Connection Length Max.Working Load
Model Area Max.stroke mm/in Piston amount
mm/in mm/in API Mm/in kN/lb
Cm2/in2
89 32 6517 93. 300 500
TLQ 89 NC26 5
3-1/4 1.25 256.6 14.5 11.8 112400
121 45 4415 133 300 561
TLQ121 NC38 3
4-3/4 1.77 173.8 20.6 11.8 126000
TLQ 165 50 5405 208 400 1500
NC46 3
165 6-1/4 2 212.8 32.2 15.7 337200
TLQ 203 71.4 5410 446 600 1600
6 5/8REG 3
203 8 2.8 213 69.1 23.6 359700
TLQ 254 76.2 5192 410 600 4000
8 5/8REG 2
254 10 3 204 63.6 23.6 899200
TLQ 340 102 5130 880 800 5000
8 5/8REG 2
340 13-3/8 4 202 136.4 31.5 1124000
Above list some models, other models also can be supplied as follows:TLQ172(6-3/4),TLQ17
8(7),TLQ229(9),TLQ241(9-1/2),TLQ245(9-5/8).
-5-
BRJ
Two-action Drill Accelerator Type SZJQ can be stored energy by hydraulic spring. It shouldbe
applied with Model QYⅡ Hydraulic Drilling Jar jointly. The drill collar and Hydraulic Jar(below the
Drill Accelerator ) can function an accelerated effect when jarring operates as formaking the stuck
point gain more jarring force.Meanwhile, it can decrease the damage of tremor produced
byup-down jarring for drill tools above DrillAcxelertor.
Technical parameters
Hole Seal Overall
Model O.D I.D Con. Max.stroke Tension of full Max.Working MaX.Torque
Pressure Length
mm/in mm/in API mm/in Stroke kN/lbf f load kN/lbf kN·m/lbf·f
Mpa/psi mm/in
95 32 178 178 35 600 4 6651
SZJQ95 NC26
3-3/4 1-1/4 7 7 5000 135000 3000 261 7/8
121 50 178 178 35 1100 15 7185
SZJQ121 NC38
4-3/4 2 7 7 5000 247000 11000 282 3/4
6
203 70 203 203 35 2600 30 8000
SZJQ203 5/8RE
8 2-3/4 8 8 5000 585000 22100 315
G
Above list some models, other models also can be supplied as follows:SZJQ165(6-1/2"),ZJQ1
97(7-3/4").
-6-
BRJ
Model “ZJQ” Drilling Accelerator can be stored energy by hydraulic spring as to increase
thejarring force for Hydraulic Jar. It should be applied with Hydraulic Drilling Jar Type QYⅡ
jointly.The drill collar and Hydraulic Jar (below the Drill Accelerator ) can function an accelerated
effectwhen jarring operates as for making the stuck point gain more jarring force that can increase
forcefor two times at the highest. Meanwhile, it can decrease the bounce-back shock after jarring
as to protect the drill tools above Drill Accelerator.
Technical Parameters
Hole Seal Overall
Model O.D I.D Connection Max.stroke Tension of full Max.Working MaX.Torque
Pressure Length
mm/in mm/in API mm/in Stroke kN/lbf f load kN/lbf kN·m/lbf·f
Mpa/psi Mm/in
121 50 350 350 30 1100 15 7430
ZJQ46 NC38
4-3/4 2 13-3/4 78700 4350 247000 11000 292.5
159 57 350 700 30 1900 25 7780
ZJQ62 NC50
6-1/4 2-1/4 13-3/4 157400 4350 42000 18400 306.25
203 76.2 350 1000 30 3000 45 7752
ZJQ80 6 5/8REG
8 3 13-3/4 224800 4350 674400 3300 305..19
241 76 350 1200 30 4000 60 6752
ZJQ95 7 5/8REG
9-1/2 3 13-3/4 270000 4350 900000 44200 265.81
Above list some models, other models also can be supplied as follows:ZJQ64(6-1/2),ZJQ76(7-3/4)
-7-
BRJ
Hydraulic Shock Absorber YJ
Technical Features
Model “YJ” Hydraulic Shock Sub should be mounted on the drilling string near the bit, absorbing or
reducing axial vibration and thrust load of the drilling string. And it has a good results for prolonging
the service life of the bit and protecting the drilling tools and the surface equipment.
Working principle
The hydraulic shock absorber is connected between drill bit and drill collar, the torque is
transferred from top drill string to mandrel. The spline transfers torque to spline outer barrel, oil
cylinder and lower sub , then drive drill bit to rotate.
The bit weight is from the which of top drill tool so that drill bit insert drill into formation to break
rock into pieces. The drilling mud is fed through bore of drill pipe and drill collar into mandrel of
shock absorber, tailpipe, lower sub bore and ejected into bottom well .Because of the uneven
bottom well conditions and special structure of cone bit, the drill bit and drill string during drilling
operation would produce severe vibration. The hydraulic shock absorber, by means
ofcom-pressible deformation of compressed liquid under the function of pressure, absorb the
energy from drill bit and drill string vibration. Thus, the shock absorber can reduce the vibration and
impact load of drill tools.
-8-
BRJ
Technical parameters
Max.Workin Yield Workin Overal
O.D Connectio Max.Workin Yield Max.Workin
Model I.D g Torque g l
mm/i n g Pull g pressure
mm/in Torque kN·m/lbf·f Stroke Length
n API load kN/lbf kN/lbf kN/lbf
kN·m/lbf·ft t mm/in Mm/in
96 38 400 530 8 10 120 100 2880
YJ95 NC26
3-3/4 1-1/2 90000 120000 5900 7400 26000 3.9 113.3
YJ12 121 38 1500 2200 15 50 265 100 4116
NC38
1 4-3/4 1-1/2 340000 490000 11000 36000 60000 3.9 162
YJ16 165 50 2000 2700 35 95 390 125 4070
NC50
5 6-1/2 2 450000 600000 25800 70000 87000 4.9 160
68
YJ20 203 2000 2700 35 95 490 140 4040
2-11/1 6 5/8REG
3 8 450000 600000 25800 70000 110000 5.5 159
6
71.4 5000
YJ25 254 3000 55 200 600 140 4100
2-13/1 8 5/8REG 112000
4 10 670000 40000 147000 130000 5.5 161
6 0
19000
YJ35 356 76 8000 150 1000 600 150 4000
8 5/8REG 427000
6 14 3 1800000 110000 740000 130000 5.9 157.4
0
Above list some models, other models also can be supplied as follows:YJ178(7"),YJ229(9"),Y
J279(11"),YJ305(12"),Also provide Mechanical-Hydraulic shock absorbers type DHJ.
-9-
BRJ
Double-way Shock Absorber SJ
Technical Features
Model “SJ” Two-Way Shock Sub should be mounted on drill string which is near the bit. It can
slow or sorbs the longitudinal bounce and peripheral torque impact of drill bit (drill string)
simultaneously. It should realize the best fitting of drill pressure and rotation rate as to reduce the
drill cost and improve the drilling efficiency. It can be used for the drill-in or coring of hard layer,
gravel layer and soft-hard interlayer.
Working principle
The torsion of bottom hole will be changed with changes in bit structure ,formation and bit
weight .When the drilling speed reaches up to a certain value ,torque and resonance will be
happened to drill string .During rotation drilling , the lower part of drilling tool simultaneously bear
axially pressure and torque. When bit weight exceed the limit value, the drilling tool will produce a
- 10 -
BRJ
transverse bending (it means lose steadiness) and torque can also make the drilling tool to lose
steadiness to be turned into a twist shape. Two positions are very typical:
1. The lower bit is suddenly frozen and then torque bumping will be produced unless the cut
down rotary energy.
The vertically damping unit is made of mandrel, piston assembly, annular space damping unit
and liquid spring of working chamber . Working mechanism: To absorb or release the vibration
energy of bit and drill string by means of compressible liquid producing spring deformation in
working chamber under the function of pressure. The mandrel moves axially relative to outer barrel
when liquid spring is in compression or explanation. Meanwhile ,the non-compressible liquid in
damping chamber flows through damping space and produces a large number of friction heat so
that some vibration and bumping energy are used up . The vertical bumping unit thus can absorb or
reduce the drilling tools’ energy in vertical vibration and bumping.
The piston change-over unit is composed of spline outer barrel which is connected with piston
by rectangular spline pair and the piston inner hole which is connected with mandrel by
ladder-shaped spiral pair. Such a group unit can turn the torque vibration and impact load into
vertical component of force in working chamber in a twinkling of an eye so that a constant torque is
maintained on.
Technical Parameters
Max.Working Max.Drill Overall
Model O.D I.D Connection Max.Working Max.Working Rigidity
Torque pressure Length
mm/in mm/in API load kN/lbf Stroke mm/in kN/cm
kN·m/lbf·ft kN/lbf Mm/in
121 38 1000 10 300 100 4208
SJ121 NC38 3.0~5.0
4-3/4 1-1/2 224800 7300 67000 3-15/16 165.66
165 48 1500 15 350 120 5494
SJ165 NC46 3.0~5.0
6-/2 1-7/8 337200 11000 78600 4-3/4 216.29
203 65 2000 20 450 120 6080
SJ203 6 5/8REG 3.0~5.0
8 2-1/2 449000 14000 101000 4-3/4 239.37
254 71.4 2500 25 600 120 6400
SJ254 8 5/8REG 3.0~5.0
10 2-3/4 562000 18000 134000 4-3/4 251.96
279 76.2 3000 30 600 160 5580
SJ279 8 5/8REG 3.0~5.0
11 3 674000 22000 134000 6-1/4 219.68
Above list some models, other models also can be supplied as follows:SJ159
(6-1/4"),SJ178(7"),SJ229(9").
- 11 -
BRJ
Full-Hydraulic Drilling Jar QY
Full-Hydraulic drilling jar type QY is a double-acting hydraulic jar and is used to free equipment
stuck down hole. It can be used with a down hole motor, because it is capable of torque
transmission, and is ideal for use in coiled tubing operations, snubbing, rotary drilling and fishing
applications. By adjusting the amount of surface push or pull (no torque or external adjustments are
required) the operator can deliver very light or maximum impacts in either direction.
Features:Model “QY” Hydraulic Drilling Jar can be acted hydraulically, realizing the stepless
control of up-down jarring tonnage.
- 12 -
BRJ
It can protect the drill string effectively and improve the using life.The hydraulic stored energy
mechanism has the advantage of reliable property and good stability. The scope of time delay
interval: 30S~240S; the scope of service temperature: -40°C~180°C. The scope of outer
diameter: 80mm~241mm.
It can adopt the new special material for higher property and safety.
It can normally used for drilling, coring, work over and fishing etc.
Technical Parameters
Tensie
Max.Upward Max.Downward Max.Working Overall
Model O.D I.D Connection Max.Working Yield
jarring force jarring force kN/lbf Torque Length
mm/in mm/in API load kN/lbf strength
kN/lbf f kN·m/lbf·f Mm/in
kN/lb
80 25.4 150 60 350 600 3 5550
QY80 2 3/8REG
3-1/8 1 34000 13500 78000 130000 2200 218.5
121 50 350 180 930 1400 15 9801
QY121 NC38
4-3/4 2 79000 40000 209000 315000 11000 385.86
165 57 700 350 600 2450 25 9830
QY165 NC50
6-1/2 2-1/4 160000 79000 360000 550000 18000 387
203 71.4 1000 500 2800 4450 35 9918
QY203 6 5/8REG
8 2-13/16 225000 112000 630000 1000000 25800 390.47
241 76 1250 650 3500 8100 40 9908
QY241 7 5/8REG
9-1/2 3 280000 146000 787000 1820000 29500 390.47
Above list some models, other models also can be supplied as follows:QY95(3-3/4”),
QY159(6-1/4” ),QY178(7”),QY229(9”).
- 13 -
BRJ
BXJ Lubricated Fishing Bumper Sub
Technical Features
Lubricated fishing bumper sub is one of the jars which produce jarring force by means of the
energy caused by heavy weight objects when moving down, its inner chamber is full of hydraulic oil
so as to ensure a longer service life. The tool is suitable for deep hole and middle deep hole
operation. With some advantages: Can produce strong one way down jarring force, maximum
jarring force, continuous down jarring force. Medium jarring force; continuous up jar, low-grade
jarring force; can release fishing tool; can act as constant pressure drill tool, simply structure, easy
operation, all these make it widely used jarring tool.
Working principle
- 14 -
BRJ
Jarring downward is made by means of conversion. Rasing drill stem shall make bumper jar to
be pull down at a certain height to produce potential energy. Go on raising drill stem, the drill stem
has a strain energy due to spring strain. When drill stem is lowered suddenly, the energy stored in
drill stem the force the drill stem to move downward in acceleration. When bumper sub reaches a
closed position, the above energies at this instant change into a large downward jarring force.
Technical Parameters
Parameters/Model BXJ31B BXJ34B BXJ36B BXJ42B BXJ44B BXJ46B BXJ62B BXJ64B BXJ70B BXJ80B
Product Code 1101000 1102000 1103000 1105000 1106000 1108000 1110000 1111000 1113000 1115000
Sealing pressure
30 30 30 30 30 30 30 30 30 30
(MPa)
Max .tensile load
30 40 50 70 80 90 143 143 153 220
(tf)
Work stroke (mm) 394 394 394 394 394 400 460 460 465 465
2 6
Connection NC26 NC26 NC31 NC31 NC38 NC50 NC50 NC50
3/8REG 5/8REG
Closed length
2355 2400 2514 2450 2450 2446 2730 2730 2950 3108
(mm)
Releasing spear
Technical features
Releasing spear provide a positive means to engage and
retrieve an internal fish form the well. It is ruggedly built to
withstand severe jarring and pulling strains. It engages the fish
over a large area without the damage of the fish. The simple
design avoids the problem of small parts lost or damaged in the
hole when operation. It may be used with other equipment such
as pack-off assemblies and internal cutters. If the fish can not
be pulled, the spear may easily be released and disengaged.
Construction
The releasing spear consists of a mandrel, grapple, releasing ring, and a bull nose nut. The
mandrel is made of specially heat treated high strength alloy steel; and may be ordered either as a
flush type to enter completely into a fish or as a shoulder type to provide a positive landing position
on top of the fish. Size and type of the upper box connection is provide according to customer’s
exact specification.
When order please specify:
The model of the releasing spear
Top connection
The exact size and weight of the fish
Plush or shoulder type mandrel
Technical parameters
model Product code Mandrel O.D (mm) Catch size (mm) Thread conn. Allowed load (KN)
- 17 -
BRJ
Taper Tap
Technical Features
The taper tap is a special fishing tool making thread in tubular dropped objects
such as drill pipe and tubing. It is a high effective tool in fishing of tubular dropped
objects especially with union. The taper tap can be used for different fishing
operation when equipped with left hand thread drill pipes and other tools. The
taper taps are made from high strength alloy steel forging material and heat
treated. It is made with chip groove so as to make threads.
Technical Parameters
Fishing OD of Fishing OD Overall
Product
model small of mall end ID (mm) OD (mm) length Overall length (mm)
code
end(mm) (mm) (mm)
Die Collar
Technical Features
The die collar is a special external fishing tool which is tapping on the outside
wall of tubing objects such as tubing and drill pipe.
The die collar is long cylindrical integral structure which is consisting of sub and
tap body with threads in interior of cone as shown in the fig I. The die collar is made
of high strength alloy ans is made with a cutting groove in the fishing threads.
- 18 -
BRJ
Technical Parameters
Fishing
Fishing
OD of Max. OD of Overall Catch size
model Product code OD of big
small end OD(mm) joint(mm) length(mm) (mm)
end (mm)
(mm)
Impession Block
- 19 -
Junk Mills
Flat-Bottom Junk MillConcave-Bottom Junk MillSkirted Junk Mill
- 20 -
BRJ
CD Elevator
Technical Features
Model CD side door elevator with square shoulder are suitable
for handling tubing, casing ,drill pipe and drill collar in oil and natural
gas drilling, well construction. The products shall be designed and
manufactured according to the requirements in API Spec 8C
Specification for Drilling and Production Hoisting Equipment.
Technical parameters
Rated Cap.
Model (in)Size
(short tons)
TA Elevator
Technical Features
Model TA center latch elevator with square shoulder are suitable
for handling drill pipe, drill collar, casing and tubing. The products
shall be designed and manufactured according to the requirements in
API Spec 8C Specification for Drilling and Production Hoisting
Equipment.
Technical Parameters
(in)Size
Rated Cap.
Model Tubing
DC Casing (short tons)
NU EU
- 21 -
CDZ Elevator
Technical Features
CDZ drilling pipe elevator is mainly used in the holding and
hoisting of drilling pipe with 18 degree taper and tools in oil and
natural gas drilling, well construction. The products shall be
designed and manufactured according to the requirements in
API Spec 8C Specification for Drilling and Production Hoisting
Equipment .
Technical Parameters
Rated Cap.
Model (in)Size
(short tons)
DDZ Elevators
Technical Features
DDZ series elevators are center latch elevator with 18
degree taper shoulder, applied in handling the drilling pipe and
drilling tools, etc. The load ranges from 100 tons to 750 dons. The
size ranges are from 2 to 6. The products shall be designed and
manufactured according to the requirements in API Spec 8C
Technical Parameters
(short tons)
Model (in)Size Remark
Rated Capacity
DD Elevator
Technical Features
Model DD center latch elevator with square shoulder are
suitable for handling drill collar, casing and tubing. The load ranges
from 150 tons to 350 dons. The size ranges are from 2 to 51/2. The
- 22 -
products shall be designed and manufactured according to the requirements in API Spec 8C
Specification for Drilling and Production Hoisting Equipment.
Technical parameters
(in)Size Rated Cap.
Model
(DP) (Casing) (Tubing) (short tons)
- 23 -
Technical parameters
Size Range(mm(in)) Rated Torque
No.of Latch Lug jaw
mm in kN·m
1# 60.3-95.25 2.3/8-3.3/4
2# 88.9-117.48 3.1/2-4.5/8
3# 114.3-146.05 4.1/2-5.3/4 48
4# 133.35-184.15 5.1/4-7.1/4
5# 174.6-219.1 6.7/8-8.5/8
6# 228.6-273.05 9-10.3/4 35
Technical parameters
Size Range(mm(in)) Rated Torque
No.of Latch Lug jaw No. of Short Jaw No.of Hinge Jaw
in mm kN·m
1 4-5.1/2 101.6-139.7
Ⅰ
2 5.1/2-5.3/4 139.7-146
1 5.1/2-6.5/8 139.7-168.3
1# Ⅱ
2 6.1/2-7.1/4 165.1-184.2
2# 2 9.1/2-10.3/4 241.3-273
Ⅱ
2 10.3/4-12 273-304.8
Ⅰ 1 12-12.3/4 304.8-323.8
- 25 -
Workover Tong
Technical parameters
Technical parameters
Size Range (mm(in)) Rated Torque
No. of Hinge Jaw
in mm kN·m
9、8 133/8~141/2 340~368.3
8、7 141/2~16 368.3~406.4
8、9、9 16~171/2 406.4~444.5
8、9、7 171/2~19 444.5~482.6
7、8、7 19~20 482.6~508
9、8、9、7 20~211/2 508~546.1
35
9、7、8、7 211/2~23 546.1~584.2
9、9、8、7、7 24~251/2 609.6~647.7
9、8、7、7、7 251/2~27 647.7~685.8
8、7、7、7、7 27~281/2 685.8~723.9
9、9、8、7、7、8 281/2~30 723.9~762
9、7、7、7、7、8 30 762
- 26 -
Manual Tongs Type DB
Technical parameters
Size Range (mm(in))
No. of Latch lug jaw No. of Hinge Pin Hole Rated Torque (kN.m)
in mm
I 31/2~6 88.9~152
1# II 53/4~7 146~178
III 65/8~81/4 168~210 90
I 8~95/8 203~244
2#
II 105/8~111/4 270~286
I 113/4~123/4 298~324
3#
II 133/8~143/8 340~365 55
4# II 16~17 406~432
- 27 -
Single-arm Elevator Link
- 28 -
Technical Parameters
Model WQ-175-5 1/2 WQ-205-5 1/2 WQ-275-5 1/2 WQ-375-5 1/2
MPa 0.6-0.9
Working Pressure
Psi 87-130
- 29 -
ZQ203-125 Drill Pipe Power Tong
Technical Features
The drill pipe power tong is an ideal oil drilling wellhead
tools, widely used in marine, land drilling and workover
operations on unloading column threaded operations. Use of
this clamp can play safety, effort to improve the ergonomics
of the role. The series clamp, open type, be free to disengage
the column, the mobile; set torque clamp and spinner clamp
at one shackle on alternative catwork, tongs and spin rope.
The tongs are in line with norms SY/T5074 standards and
API Spec 7K.
Technical Parameters
Model ZQ127-25 ZQ162-50 ZQ203-100 ZQ203-125 Model
Air pressure
- 30 -
TQ340-35Y Casing Tong
The casing tong is used to make up and break out for
casingoperation in oil fields.The power tong has the
following feature as well:
Opening type, double swing head jaws, convenient to
assemble and disassemble;
Brake belt assembly, open gear supporting
structure,improving the strength and rigidity;
Wholly hydraulic mode and mechanical gear shift;
With torque gaugeoptional torque control system to display,
control and record the make-up torque;
Technical Parameter
Model TQ178-16 TQ178-16Y TQ340-35 TQ356-55Y TQ508-70Y TQ340-85Y
MPa 18 16 18 20 20 18
Max. Pressure
psi 2610 2320 2610 2900 2900 2610
stroke in 67 55 65 59 59 59
Wire rope mm 16 20 22 20 26 26
Swivel
Technical Features
Series travelling blocks conform to API
Spec 8A, and are granted the right to
use API monogram.
Conform to industry standard
SY/T5527.
Double pin threaded alloy steel sub is
optional.
Wash pipe and packing device are integral type structure, convenient for replacing.
Complete with API 4LP hose joint.
- 32 -
Technical Parameters
Model SL135 SL170 SL225 SL450
Stem I. D mm 64 64 75 75
To stem API 4 1/2” REG, LH 4 1/2” RWG,LH 6 5/8” RWG,LH 7 5/8” RWG,LH
Sub thread
To Kelly API 6 5/8” RWG,LH 6 5/8” RWG,LH 6 5/8” RWG,LH 6 5/8” RWG,LH
- 33 -
ZQ203-125 Drill Pipe Power Tong
Technical Features
The drill pipe power tong is an ideal oil drilling wellhead tools,
widely used in marine, land drilling and workover operations on
unloading column threaded operations. Use of this clamp can
play safety, effort to improve the ergonomics of the role. The
series clamp, open type, be free to disengage the column, the
mobile; set torque clamp and spinner clamp at one shackle on
alternative catwork, tongs and spin rope. The tongs are in line
with norms SY/T5074 standards and API Spec 7K.
Technical Parameters
Model ZQ127-25 ZQ162-50 ZQ203-100 ZQ203-125 Model
Air pressure
- 34 -
Elevator/Spider
Technical Features
Slip Type Elevators/Spiders are mechanized tools with air operating.
They can handle casings up to 24.1/2inch. They are easy to operate
and dependable enough. Also they can reduce workload. They are
designed and manufactured according to API Spec 8C.
applicable diameter of
Model Rated capacity(tons) Work pressure(MPa) Max. pressure (MPa)
tubulars(in)
- 35 -
mechanism is used between the body and bonnets,so it
is not necessary to apply too much pretightening force
to secure the reliability of sealing, It is very convenient
to lift and transport the BOPs with the four lifting rods,
The new sealing mechanism of ram shaft secures the
sealing reliability under the high pressure, The ring
grooves of flanges are all lined with the corrosion
resistant alloy, Matched-manufacturing is not
necessary for the bonnets and body,so the diserepancy could be eliminated by thestructure.And it
is convenient for the maintenance in the future.
According to the latest API Spec 16A standard
According to the latest API Spec Q1 , quality standard of IOS9001 and NACE-MR-01-75 ,H2st Trim
According to user requirements and the use of environmental can choose casting or forging.
BOP Parts
DQST140-J Electro-Pneumatic
Technical Features
DQST140-J electro-pneumatic high pressure test unit is a newly developed wireless remote
control product. T has two sets of power system, one is electric triplex water pump and the other is
pneumatic pump. Electric pump is used for enlarging displacement and pneumatic pump or
pressurization. Electric pump, whose displacement reaches 50L/min. is driven by 3 phase AC
power. And pneumatic pump is driven by compressed air. The stop pressure can be preset value,
- 36 -
air source of pneumatic pumps stop working. As
air source pressure is directly proportional to
output liquid pressure, the output liquid pressure
can be adjusted within a definite range through
adjusting air source pressure reach balance,
pneumatic pump stops and output liquid pressure
remain on preset value.
This unit is equipped with wireless remote
control panel, and it can be controlled remotely
and also can monitor, record, print and look back
the pressurizing process. Additionally, an A4 paper printer is delivered with the unit, which can print
the data curve directly. This unit can has high pressure alarm function and judge whether the
pressure test is qualified, so safety and practicability of the unit is highly improved.
Technical parameters
Item Specifications
Displacement 21 L/min
Triplex water pump
Nominal working pressure 35MPa
1:60 pneumatic pump 90ml/stroke
Pneumatic pump displacement
1:200 pneumatic pump 14mL/stroke
Transmitter signal 4~20mA
Size 2900L*1560W*2260H
weight 3t
- 37 -
3. Application standard: API Spec 16D SY/T5053.2-2002
Technical parameters
Operating time
Nominal (min)with
Outer dia. of hose Operating Min. burst Min. bending
inner Thread fire-resisting at
assembly(mm) pressure(MPa) pressure(MPa) radius(mm)
dia.(mm) 750℃
Normal Limit
44 35 105
19 280
50 70 175
47 35 105
22 320
53 70 175
50 35 105
25 360 NPT LP 5 25
56 70 175
56 35 105
31.5 460
62 70 175
63 35 105
38 560
69 70 175
Choke Manifod&Manifold
When the well head pressure going up, the
drilling fluid can be pumped into well with the
killing manifold in order to balance the well
bottom pressure, to prevent well from kicking and
blow-out; the blowout pipeline which connected to
blowout directly can be used to release the well
bottom pressure; to inject mud cementing
operation by injecting water and extinguishing
agent into the well head as well. It only can inject
heavy fluid or other fluid into well by check valve,
but the backflow and other operation. Killing
manifold consists of check valve, gate valve,
pressure gage, connection pipeline, etc. One of its ends is connected with BOP cross, the other
end is connected with injection pump, both killing manifold and choke manifold are designed and
mating used according to API 16C requirement.
The grades of kill manifold made in our company as followings: 14MPa、21MPa、35MPa、70MPa、
105MPa, etc.
(1)The working pressure of all the pipelines, gate valves, check valves must be matched with
the working pressure of the BOP assembly which it adopts.
(2)Kill manifold cant be used as the common priming drilling fluid pipeline.
- 39 -
Technical parameters
Description Chock manifold Killing manifold
Model JG/S2-35 JG/SY-35 JG/SY2-70 JG/S2Y2-105 YG-35 YG-70 YG105
W.T.℃(℉) P.U-29~121(-20~250)
Working
Mud/Oil/(W/H2S)
medium
Double Double
Wing Wing Three-way
Four-way double
structure structure structure Double-wing structure
Control type hydraulic/manual
manual manual hydraulic/manual pneumatically controlled
throttle valve
throttle throttle throttle valve
valve valve
- 40 -
Plug valve
The plug valve is indispensable and vital equipment, used to
connect high pressure manifold in well cementation and
crushing operating for oil field, high pressure liquid control field
is available also. The plug valve holds compact structure,
easy-maintain, low torque, open quickly, ending connections
( Union, threaded type ). So it is the ideal valve for well
cementation and crushing manifold.
Specifications
Bore size: 2”~4”
Working Pressure Rating: 5000psi~15,000psi
Material Class: AA-FFProduct Specification Level: PSL1~PSL3
Temperature Class: PU (-29~121℃)Performance Requirement Level: PR1~PR2
- 41 -
High-pressure hammer union
Th
e high-pressure union is made of forged high-strength alloy steel with advanced technology
introduced from abroad. Strict heat treatment ensures that the joints provide uniform metallographic
structure and good load-carrying capacity. All the materials used fully comply with the standard of
ASTM and AISI,and the technological specifications fully comply with the API Spec 16A standards.
The products are reliably sealed. And can be easily and quickly connected to or removed from the
pipeline. Furthermore ,these unions can be used interchangeably with the others of a similar kind.
The products can be connected to the pipes by using different end connections such as pipe thread,
tubing thread,butt welding and pressure-seal end connections.
The models of high pressure union are as followings: model 100, model 200, model 206,
model 207, model 211, model 300, model 402, model 600, model 602, model 1002, model 1003,
model 1502, model 2002, and model 2202.
70MPa(10000psi) √ √ √
L type joint F*M、M*M
105MPa(15000psi) √ √
F*M、M*M 42Mpa(6000psi) √ √ √
FMF、FMM 42Mpa(6000psi) √ √ √
FFFF、FFMF 42Mpa(6000psi) √ √ √
42Mpa(6000psi) √ √ √
105MPa(15000psi) √ √
70MPa(10000psi) √ √
Fishtall joint (cross manifold) M*F*F*F
105MPa(15000psi) √ √
Casing heads
The casing head ,a component connecting the casing to
the wellhead assembly of various types and sizes ,is used to
support the both the intermediate (protective) string and the
production string ,and to seal up the annular space between the
casing, thus providing a crossover connection for the installation
- 43 -
of the bop ,the tubing head, theChristmas tree and other top wellhead components. It is also used
to inject additional cement slurry or balance fluid,monitor the well sink,and execute other operatins
through both of the two bypass holes in the casing head body.
The YYPMC casing head ,which is of standard structure ,is fitted with a complete set of
casing head hangers manufactured by YYPMC,which areAvailable for choice according to different
requirements of casing procedure and wellhead conditions.the top part of the body is API6B or
API6BX flanged.
Options of casing head
there are four options for the bottom connection of the casinghead:API NPT box ,API CSG
box,sow type and slip-type.
YYPMC can supply you with welded support yoke.
there are two types of side outlets:threaded and studded,the latter of which is processed with VR
female threads for VR plug.
2000~15000
Working pressure psi(Mpa) Nominal Size in( mm) 2 1/16~4 1/16 (52~103)
(14~105)
Rated Working
Performance Requirement Level PR1~2 P.U -29~121℃
Temperature
Applicable Medium Crude oil,Natural gas Connection Type Flange or Clamp
Casing Spool
The casing spool features a versatile straight bore design that
can accept a wide variety of slip and mandrel type casing hangers,
minimizes risk of damage to sealing areas by drilling tools, and
prevents test-plug and blowout preventer wedging problems when
pressure is applied.
It can be equipped lock screws, outlets (line pipe or studded
side with VR thread) or secondary seal structure, test port.
Technical parameters
Bore size: 16-3/4”Max.
- 44 -
Working Pressure Rating: 3000psi~15,000psi
Material Class: AA-FF
Temperature Class: PU (-29~121℃)
Product Specification Level: PSL1~PSL3
Performance Requirement Level: PR1~PR2
Kelly Valve
Kelly valve is a manually operated ball type drill stem valve; it is divided
into upper Kelly valve and lower Kelly valve. The upper Kelly valve is
connected between lower end of swivel and upper end of Kelly; the lower
Kelly valve is connected between upper end of drill pipe and lower end of
Kelly or connected between lower end of Kelly saver subs. The Kelly valve
can be opened on or closed off by only turning the special operating wrench at
90° according to indicating direction. During drilling operation, the Kelly valve
shall be connected at upper end and lower end of Kelly.The sealing principle
for Kelly valve is that the ball is positioned and provided with proceeding
stress by the lower seat supported by spring load and a close seal between
ball and ball seat is provided. During normal drilling operation, the hole is kept
unblocked by turning the stem to be “on” position; In case of kick or blowout,
turn the operating stem to be “off” position to close off the internal bore of drill
string, the kick or blowout accident is avoided due to a high pressure sealing
situation between ball and ball seat.
When ordering please specify:
● Upper or Lower type;
● Tool OD;
● Working Pressure: 5,000 / 10,000 / 15,000 PSI;
● Tool connection.
Specifications - Upper Kelly Valve
Product O.D. Thread connection I.D. Max.sealing
Model
Code (mm) (LH) (mm) pressure(Mpa)
CS
F021461 146 4 1/2 REG 50 68.6
146K
CS
F022001 200 6 5/8 REG 76.2 68.6
200K
Specifications - Lower Kelly Valve
O.D. Thread connection I.D. Max.sealing
Model Product Code
(mm) (LH) (mm) pressure(Mpa)
XS105K F021051 105 NC31 40 68.6
XS121K F021211 121 NC38 44.5 68.6
XS127K F021271 127 NC38 44.5 68.6
XS140K F021402 139.7 NC40 57.2 68.6
XS159K F021591 159 NC46 61 68.6
XS165K F021653 165 NC46 61 68.6
F021782 ,
XS178K 178 NC50 , 5 1/2FH 71.4 68.6
F021782
- 45 -
Full Opening Safety Valve
Full Opening Safety Valve (short for FOSV) is a ball type safety valve
used to stop flow through the drill string when the drill string is being withdrawn
from the well. FOSV is dual body full-opening safety valve, so it does not
interfere with the running of tools such as core barrels or survey instruments. It
is designed to be stabbed into the top joint of drill pipe or tubing string at the
rig floor and closed quickly in case a well kicks.
The ball-type design permits the valve to be compact, easy to handle,
and yet have great strength. Standard test pressure is 10,000PSI, but higher
pressure ratings are available.FOSV and operating wrench be should be
maintained on the rig floor at all times.When ordering please
specify:Connection.O.D. and I.D.
- 46 -
Top Drive Valve(TDS Corker)
Top Drive Valve includes Upper IBOP for Top Drive and Lower IBOP for
Top Drive. They are used for top drive drilling system joined one by one. The
IBOP for Top Drive allows free passage of drilling fluid without pressure loss
in the course of work. The valves can control blowout pressures, or as a valve
to prevent loss of fluid when the pipe is disassembly.The valve seals in both
directions with metal to metal seals. Availablein 10,000 psi/15,000 psi working
pressure with corresponding 15,000psi/22,500psi testing pressure before
they are released to end users.
Specifications
O.D I.D OVERALL LENGTH
Type CONNECTION
mm(inch) mm(inch) mm(inch)
6 5/8REG BOX 572
DSS187 Upper IBOP
187 77.8 6 5/8REG BOX (22 1/2)
(7 23/64) (3 1/16) 6 5/8REG BOX 523
DSS187 Lower IBOP
6 5/8REG PIN (20 19/32)
572
DSS197 Upper IBOP 6-5/8REG
197 77.8 (22-1/2)
(7-3/4) (3-1/16) 523
DSS197 Lower IBOP 6-5/8REG
(20-19/32)
DSS216 Upper IBOP 7-5/8REG (25-5/8)
216 77.8
512
DSS216 Lower IBOP (8-1/2) (3-1/16) 7-5/8REG
(20-5/32)
Technical Parameters
Working
Model Product Code O.D.(mm) Connection I.D.(mm)
Pressure(MPa)
FJ229 F042291 229 7 5/8 REG 82 70(35)
FJ203 F042031 203 6 5/8 REG 82 70(35)
FJ178 F041784 178 5 1/2 FH 82 70(35)
FJ168 F041681 168 NC50 82 70(35)
FJ165 F041652 165 NC50 82 70(35)
FJ159 F041591 159 NC46 70 70(35)
FJ121 F041211 121 NC38 56 70(35)
FJ105 F041051 105 NC31 44 70(35)
FJ89 F040891 89 NC26 33 70(35)
- 48 -
Inside Bop
Inside blowout preventer (Inside BOP) is a special tool, which can be striped
through the BOP preempt to be connected with the added drilling tools as soon
as possible, when the blowout is happened during lifting the drilling tools, the
inside blowout preventer has many advantages such as high-pressure, sealed
reliable, easy to operate, switch quickly and so on.
During the drill tool is coming out of hole, the blowout is happened because of
suction result, When the fluid, oil, steam or water comes out from discharged drill
pipe, the inside blowout preventer should be quickly connected to the drill pipe,
The inside blowout preventer can be easily connected to the drill pipe due to the
fact that the valve of blowout preventer is at open position and the fluid in down
hole can flow out of inside blowout preventer is at open position and the fluid in
down hole can flow out of inside blowout preventer, The relief rod can close the
valve by screwing out the locking bolt, right now, the inside blowout preventer
allows the fluid to be pumped in hole from top to bottom, but the in hole fluid is not
able to flow into drill string and finally flow out of inside blowout preventer Then the purpose of
blowout prevention van be reached by the following steps, Discharge the relief sub regulate the
fluid and start the pump circulation.
When ordering please specify the connection of drillstring.
Technical Parameters
Inside Blowout Preventer
Thread Working
Product Code O.D.(in) I.D.(in) Length(in)
connection Pressure(MPa)
2 3/8IF F0108900 3 3/8~3 3/4 1 1/4 27~28 70(35)
Lift Sub
A Lift Sub enables the safe, efficient handling of straight OD tubulars such as drill collars, shock
tools, jars, directional equipment and other tools by using the drill pipe elevators,default length 36".
- 49 -
Saver Sub
Saver Sub is used to extend the life of the Kelly by taking the connection
wear each time it is make-up to a drill stem component. The saver sub
connection is sacrificed because it can be easily repaired or
inexpensively replaced. The saver sub can be equipped with a rubber
protector to reduce BOP equipment and casing wear resulting from
contact damage with a lower Kelly connectiondefault long,default length
24".
Straight OD Sub
Straight OD Sub is used to connect drill stem members that have a
similar outside diameter. The drill bit, downhole tools, heavy weight
drill pipe and drill pipe can be crossed over using a straight OD
sub,,default length 36".
By-Pass Vavle
During drilling operation, when well kick is taken place and bit
bore is blocked. The by-pass valve can be opened to go fluid
circulation and well killing .Before drilling in flow gas formation, the
by –pass valve shall be located near or on the bit.When take
place well kick and pump pressure is too high or blocked, the
following steps can be taken to open the by-pass valve :
● Discharge Kelly and drop in a steel ball (or a Nylon ball) which is
carried by tool;
● Connect with Kelly;
● Put ball into retainer by pump circulation;
● When fluid is closed, the shear pin can be sheared off with
adding 0.5~1.5Mpa pump pressure than original pump pressure;
● After pin is sheared, the seal sleeve move down to open the
discharge hole and pump pressure come to drop down , then
- 50 -
normal circulation and well killing operation can be started.When ordering please specify:
● O.D. of body;
● Connection;
● Pump pressure to shear off pin if other than standard.
Specifications
Pump
Top O.D. of
Product O.D. Seal sleeve Bottom Pressure of
Model Connection Steel ball
Code (mm) (mm) connection shear-off
(BOX) (mm)
shear pin
PTF105 F061053 105 32 NC31 NC31(PIN) 3-10MPa 35
PTF121A F061213 121 38 NC38 NC38(PIN) 3-10MPa 45
PTF127 F061273 127 38 NC38 NC38(PIN) 3-10MPa 45
3 1/2
PTF127C F061272 127 38 NC38 3-10MPa 45
REG(BOX)
PTF159 F061591 159 49 NC46 NC46(PIN) 3-10MPa 54
4 1/2
PTF159B F061594 159 49 NC46 3-10MPa 54
REG(BOX)
PTF168 F061681 168 50.8 NC50 MC50(PIN) 3-10MPa 57
6 5/8
PTF203 F062031 203 62 6 5/8 REG 3-10MPa 65
REG(PIN)
- 51 -
Technical Parameters
Product Code Product Code
Sub O.D. Valve
Model ( with arrow type ( with plate type Joint connection I.D.(mm)
(mm) O.D.(mm)
float valve) float valve)
FFJT241 J0917110 J1017110 Φ241.3 7 5/8REG B×B Φ121(5F6R) Φ76.2
- 52 -
Technical Feature
AJ type safety joint is a specialized joint consisting of two parts. The specialized
joint takes protective effect for drilling stem in drilling , repairing and test oil (gas)
engineering, etc. It is used to treat well bottom accident and used to be on -the
-way test in drilling and coring operation. It is connected to the required position of
drilling stem to protect drilling stem without any influence on the normal working
of drilling tool.
Technical parameters
Model Product Code O.D. (mm) I.D. (mm) Thread Conn
Lifting Cap
The lifting caps are tools for lifting of drilling tools, such as drill collars, stabilizers.
specifications
Pump
Seal Top Bottom O.D. of
Product O.D. Pressure of
Model sleeve Connection connectio Steel ball
Code (mm) shear-off
(mm) (BOX) n (mm)
shear pin
Product O.D. Length Product O.D. Length
Connection Connection
Code (mm) (mm) Code (mm) (mm)
7 5/8 REG Pin J061501 210 290 7 5/8 REG Box J061601 230 290
6 5/8 REG Pin J062301 190 280 6 5/8 REG Box J061301 200 280
4 1/2 REG Pin J062201 145 260 4 1/2 REG Box J060805 160 270
3 1/2 REG Pin J060401 100 220 3 1/2 REG Box J062103 110 260
2 3/8 REG Pin J060102 80 190 2 3/8 REG Box J062102 110 200
NC50 Pin J060802 155 270 NC50 Box J060804 160 260
NC46 Pin J060801 150 270 NC46 Box J060803 160 260
NC38 Pin J060501 115 260 NC38 Box J060602 120 270
NC31 Pin J060402 100 210 NC31 Box J060601 120 220
NC26 Pin J060201 89 200 NC26 Box J062101 110 200
200
2 7/8 EUE Pin J060105 80 220 2 7/8 EUE Box J060303 95
- 53 -
Thread Protector
Product Main Material:Steel
Quality Control:Follow the API Q1 quality inspectionstandard. Base
on the API 5CT Annex I when design the product.
Applications:Products are the required parts for oildrill pipes and
drill color that can protect the thread of each side of pipe.Mainly
Thread protectors can prevent your connector threads and pipe end
fromdamaging during handling, transportation and storage .
When ordering please specify:
● O.D. of body;
● Connection Type(NC\REG\IF\FH).
48.26 1.9"NUE ▄ ▄
2 3/8"NUE ▄ ▄
60.33
2 3/8"EUE ▄ ▄
2 7/8"NUE ▄ ▄
70.3
2 7/8"EUE ▄ ▄
88.9 3 1/2"NUE ▄ ▄
- 54 -
3 1/2"EUE ▄ ▄
4"NUE ▄ ▄
101.6
4"EUE ▄ ▄
4 1/2"NUE ▄ ▄ ▄
4 1/2"EUE ▄ ▄ ▄
114.1 4 1/2"STC ▄ ▄ ▄
4 1/2"LTC ▄ ▄ ▄
4 1/2"BTC ▄ ▄ ▄
5LTC" ▄ ▄ ▄
127.0
5"BTC ▄ ▄ ▄
5 1/2"STC ▄ ▄ ▄
139.7 5 1/2"LTC ▄ ▄ ▄
5 1/2"BTC ▄ ▄ ▄
6 5/8" STC ▄ ▄ ▄
6 5/8" BTC ▄ ▄ ▄
7"STC ▄ ▄ ▄
7"BTC ▄ ▄ ▄
7 5/8 LTC" ▄ ▄ ▄
193.7
7 5/8 BTC" ▄ ▄ ▄
8 5/8"STC ▄ ▄ ▄
219.7 8 5/8"LTC ▄ ▄ ▄
8 5/8"BTC ▄ ▄ ▄
9 5/8"STC ▄ ▄ ▄
244.5 9 5/8"LTC ▄ ▄ ▄
9 5/8"BTC ▄ ▄ ▄
13 3/8"STC ▄ ▄ ▄
339.7 13 3/8"LTC ▄ ▄ ▄
13 3/8"BTC ▄ ▄ ▄
51/2"FH
6 5/8"REG
- 55 -
PetroLeum Equipment Thread Gauge
BRJ supplies all kinds of Thread Gauges listed in the API Spec.5B and API Spec 7-2.
when ordering,please specify:
1. Type of the Thread.
2. Size of Gauge.
3. Reference master or working gauges or smooth taper gauges.
4. Bos or Pin or both;Ring or plug or both.
5. Right hand or left hand,in case API Spec 7-2 Thread gauges.
Mud Pump
- 56 -
Technical Parameters
Mud pump mode F-500 F-800 F-1000 F-1300 F-1600
- 57 -
Quintuplex Plunger Pump
Model Q230 is a single acting quintuplex plunger pump rated
at 230 HP in continuous duty services and up to 285 HP in
intermittent duty. This versatile pump is offered with a variety
of material and design options that make it ideal for general
industrial, reverse osmosis, and typical applications involved
in the production of oil and natural gas.
Specifications
Model T3, T8, T13, T18, T40, T50, T60, T65, T85, T120, T145, T165, T170, T185, T200, T265,
T270, T285 can also be supplied.
- 58 -
High G Drying Shaker
Technical Features
force up to 8.0 adjustable for drying solids
discharge.
Mechanical shaker deck angle adjustable while
working
Patent tighten rubber sealing for shaker deck and
screen, long life and easy replacement.
Shaker bottom deck made from Stainless Steel for
long service life.
Heat treatment on complete shaker deck for High G force operation.
4 Panel Pretensioned Shaker screen for fast screen replacement.
Famous Brand Vibration Motors: IEC Ex, ATEX and UL Certified
Low Profile Hopper Feeder for easier cuttings transfer.
Technical parameters
Model CNZS594HGE-LD
EX Standard ExdIIbt4/IECEX/ATEX
- 59 -
Desilter
Technical parameters
Model GNZJ752E-8N/12N GNZJ703E-8N/12N GNZJ703E-16N GNWSE-12N-16N
240
Capacity (M3/H) 120/240 360 (1584GPM) 240/360
(1056GPM)
Desander Size (Inch) 4
Technical Parameters
Model GNZJ752E-1S/2S GNZJ703E-D2S GNZJ703E-3S GNWSE-2S/3S
240
Capacity (M3/H) 120/240 360 (1584GPM) 240/360
(1056GPM)
Desander Size (Inch) 10
EX Standard ExdIIBt4/IEcex/A-TEX
- 61 -
Desander Cemtrifuge(High Configuration)
Patent Design with the highest configuration and best material
for long and reliable service.
Bowl Material form Duplex Stainless Steel 2205 by centrifugal
casting.
Screw protection: Tungsten Carbide Tiles for longer life and
easier replacement.
Screw flow distribution port and bowl solids discharge port
protected by special ceramic insert.
Easily adjustable liquid discharge weir height for flexible application.
Bowl assembly supported by tighten belt for protection of bearing in moving.
Pressurized EX Proof VFD control cabinet with PLC controlled.
Genuine SKF bearing for longer and reliable operation.
Technical Parameters
Model GNLW363CG GNLW363CG-VFD GNLW453C-VFD GNLW553C-VFD
- 62 -
Mud Pump parts
- 63 -
- 64 -
Model Dsc Single Plug Cement Head
Special tool for pumping slurry and releasing plug.
The DSC Single-Plug Cement Head can be connected with casing.
Technical Features
Main parts are made from AISI4145H alloy steel. Quick-latch adapter is
designed to offer easier, faster and safer makeup for two-stage cementing.
The Balance Pipe eliminates the sucking to plug due to U-Tube effect and
ensures easy release of the plug retainer..
The Plug Indicator indicates the plug release action.
It is manufactured utilizing API grade steels with connections for API 8 round,
buttress and premium threads. LCSG (LTC) CSG (STC) BCSG (BTC) TP-CQ
TS3SB TP-NF VAM TOP NEW VAM.
Technical Parameters
Working Plunger
Specifications I.D. of Plug Length of Plug
Pressure Assembly
in. Container mm Container, mm
MPa Number
4" 35,50,70 90 300 Single
4½" 35,50,70 100 320 Single
5" 35,50,70 110 400 Single
5½" 35,50,70 125 400 Single
6⅝" 35,50,70 150 450 Single
7" 35,50,70 160 450 Single
7⅝" 35,50,70 175 450 Single
8⅝" 35,50,70 200 500 Single
9⅝" 35,50,70 225 550 Single
10¾" 21,35,50 250 550 Single
11¾" 21,35,50 275 550 Double
13⅜" 21,35,50 320 600 Double
16" 14,21,35 386 650 Double
18⅝" 14,21,35 452 650 Three
20" 14,21,35 485 650 Three
- 65 -
Model Ssc Double Plug Cement Head
Special tool for pumping slurry and releasing plug. It can couple with two plugs
simultaneously, and makes the drilling fluid fill into casing in turn and quickly.
This can simplify the cementing operation, prevent cement pollution.
Technical Features
Quick-latch adapter is designed to offer easier, faster and safer makeup for
two-stage tool cementing.
Double balance pipe is developed.
Positive lever indicates plug releasing.
Main parts are made from AISI4145H alloy steel
Top cover and union nut with large trapezoidial-threaded, it makes the tool
convenient to disassemble and carry.
It is manufactured utilizing API grade steels with connections for API 8 round,
buttress and premium threads. LCSG (LTC) CSG (STC) BCSG (BTC) TP-CQ TS3SB TP-NF
VAM TOP NEW VAM
Technical Parameters
Working I.D. of Plug Length of Plug Container, mm
Specifications
Pressure Container Top& Bottom Plug Stage Tool
in.
MPa mm One Two One Two
4" 35,50,70 90 240 240 300 300
4½" 35,50,70 100 240 240 320 320
5" 35,50,70 110 260 260 400 400
5½" 35,50,70 125 260 260 400 400
6⅝" 35,50,70 150 290 290 450 450
7" 35,50,70 160 310 310 450 450
7⅝" 35,50,70 175 310 310 450 450
8⅝" 35,50,70 200 310 310 500 500
9⅝" 35,50,70 225 330 330 550 550
10¾" 21,35,50 250 360 360 550 550
11¾" 21,35,50 275 360 360 550 550
13⅜" 21,35,50 320 410 410 600 600
16" 14,21,35 386 510 510 650 650
18⅝" 14,21,35 452 510 510 650 650
20" 14,21,35 485 510 510 650 650
- 66 -
Cup Tester
Technical Parameters
Applicable casing dimensions Rubber Rubber
Max.bearing
Product I.D. cup cup
Model O.D. pressure Length
Code O.D. O.D.
Wallthickness (MPa)
(in) mm) ppf (mm) (mm)
(mm)
- 67 -
Model Dct Casing Centralizer
Super-strengthen spring steel is applied to centralize casing in wellbore,
and improves cementing quality.
Technical Features
Every attachment is pressed into shape by moulding instead of
welding and rivet.
3-Section structure for easy transport.
Starting force and restoring force conform to API standards.
Easy-and-convenient to use.
Alternative turbulence plates can effectually improve displacement
efficiency.
Technical Parameters
Specifications 20" 18⅝" 16" 14" 13⅜" 12¾" 10¾" 9⅝" 7⅝" 7" 6⅝" 5½" 5" 4½"
Casing Size 20" 18⅝" 16" 14" 13⅜" 12¾" 10¾" 9⅝" 7⅝" 7" 6⅝" 5½" 5" 4½"
Open Hole 24" 22" 20" 8
18" 17½" 17½" 12¼" 12¼" 9⅞" 8½" 8½" 6½" 6"
Size 26" 24" 22" ½"
650 590 550
O.D., mm 484 470 466 370 375 273 252 245 256 190 181
714 680 613
Casing Spring Centralizer
Technical Parameters
Type Inside diameter Height Total height Largest diameter
- 68 -
Cementing Plugs
The Top Cementing Plug and Bottom Cementing Plug comply
with API standards. Top Cementing Plug, also known as Plug,
can be individually applied to single plug cementing. Top
Cementing Plug is solid, Bottom Cementing Plug is hollow
and has a rubber membrane separated.
Plug body material is nitrile rubber, Plug core material is aluminum alloy, can be used PDC drill bit
or rock bit addition.
Technical Features
The cementing plugs can effectively isolate cement slurry from drilling fluid, eliminating slurry
contamination.
The non-rotating design saves drill-out time.
Cementing Plug rubber material can withstand oil, acid, alkali.
Technical parameters
Size O.D., Length Bottom Cementing Plug Rubber
inch mm mm membrane burst pressure, MPa
4½" 114 210 1~2
Float Collar
Technical Features
The Float Collar is run in a casing assembly, usually several joints above
the Float Shoe. It serves as an extra back pressure valve sealing against
pressures from blow while running the assembly and after the cementing
job. Internal latch and valve are readily drillable. Its capability of
back-pressure is over 25MPa.
Technical Parameters
20"、16"、13⅜"、10¾"、9⅝"、7"、6⅝"、5½"、5"、4½"、4"、3½".
- 69 -
Float Shoe
Technical Features
Like the Float Collar, the FS float shoe also has a back-pressure valve to prevent back flow. It
permits cement to run through side ports when the nose of the shoe is on the bottom. Inner valve
and bottom guides are all made of drillable material. Its capability of back-pressure is over 25mpa.
Technical Parameters
20"、16"、13⅜"、10¾"、9⅝"、7"、6⅝"、5½"、5"、4½"、4"、3½"
- 70 -