Professional Documents
Culture Documents
Typical Applications
Figure 1 Schematic
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 1
SY8286A
Pinout (top view)
(QFN3x3-20)
Top Mark: AWRxyz, (Device code: AWR, x=year code, y=week code, z= lot number code)
Pin Name Pin Number Pin Description
Boot-strap pin. Supply high side gate driver. Decouple this pin to LX pin with
BS 1
0.1uF ceramic capacitor.
IN 2,3,4,5 Input pin. Decouple this pin to GND pin with at least 10uF ceramic cap
LX 6,19,20 Inductor pin. Connect this pin to the switching node of inductor
GND 7,8,18,EP Ground pin
Power good Indicator. Open drain output when the output voltage is within 90% to
PG 9
120% of regulation point.
NC 10, 16 Not connected
EN 11 Enable pin. Pull this pin high to turn on IC. Do not leave this pin floating.
Operating mode selection under light load. Pull this pin low for PFM operating,
MODE 12
and pull this pin high for PWM operation. Do not leave this pin floating
ILMT 13 Output current limit threshold selection.
FB 14 Output feedback pin. Connect to the center point of resistor divider.
External 3.3V bypass power supply input. Decouple this pin to GND with a 1uF
BYP 15
ceramic capac tor. Leave this pin floating if it is not used.
Internal 3.3V LDO output. Power supply for internal analog circuits and driving
VCC 17
circuit. Decouple this pin to GND with a 2.2uF ceramic capacitor.
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 2
SY8286A
Block Diagram
IN
Input
UVLO
Current Sense
PG
BS
EN
ILMT
MODE
PWM LX
Control &
Protection Current Sense
Internal
SST Logic
OTP
0.6V
GND
FB
IN
BYP 3.1V
3.3V LDO VCC
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 3
SY8286A
Electrical Characteristics
(VIN = 12V, TA = 25°C unless otherwise specified)
Parameter Symbol Test Conditions Min Typ Max Unit
V
Input Voltage Range IN 4 23 V
V
Input UVLO Threshold UVLO VIN Rising 3.9 V
V
UVLO hysteresis HYS 0.1 V
Quiescent Current IQ IOUT=0, VOUT=VSET*105% 120 145 µA
I
Shutdown Current SHDN EN=0, 6 10 µA
V
Feedback Reference REF 0.594 0.6 0.606 V
Voltage
R
Top FET RON DS(ON)1 38 mΩ
R
Bottom FET RON DS(ON)2 19 mΩ
I
Output Discharge Current DIS 70 mA
I
Top FET Current Limit LMT,HSFET 17 A
I
Bottom FET Current LMT, LSFET ILMT=Low 6.7 7.8 8.9 A
Limit ILMT=Floating 9.3 10.6 11.9 A
ILMT=High 12 13.3 14.8 A
t
Soft Start Time SS 1.3 ms
V
EN/MODE Rising ENH 1 V
Threshold
V
EN/MODE Falling ENL 0.4 V
Threshold
V
ILMT Rising Threshold ILMTH Vcc-0.5 V
V
ILMT Falling Threshold ILMTL 0.5 V
F
Switching Frequency OSC 510 600 690 kHz
T V =V
Min ON Time ON,MIN IN INMAX 50 ns
T
Min OFF Time OFF,MIN 150 ns
V
VCC Output Voltage CC With 1mA Lo d 3.2 3.3 3.4 V
V %V
Output Over Voltage OVP VFB Rising 115 120 125 REF
Threshold
V %V
Output Over Voltage OVP,HYS 1.5 REF
Hysteresis
t
Output OVP Delay OVP,DLY 20 µs
V %V
Output Under Voltage UVP VFB Falling 57.5 62.5 67.5 REF
Protection Threshold
t
Output UVP Delay UVP,DLY 200 us
V %V
Power Good Threshold PG VFB Rising (Good) 92 REF
V %V
Power Good Hysteresis PG,HYS 1.5 REF
t
Power Good Delay PG,RISING Low to high 200 µs
t
PG,FALLING High to low 10 µs
V
Bypass Switch Turn -on BYP 2.97 3.1 3.21 V
Voltage
V
Bypass Switch BYP,HYS 0.15 V
Switchov r Hysteresis
V
Bypass Switch OVP BYP,OVP 120 %VCC
T
Thermal Shutdown SD 150 °C
Temperature
Thermal Shutdown THYS 15 °C
hysteresis
Note 1: Stresses beyond the “Absolute Maximum Ratings” may cause permanent damage to the device. These are
stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated in the
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 4
SY8286A
operational sections of the specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability
Note 2: Package thermal resistance is measured in the natural convection at TA = 25°C on a four-layer Silergy
Evaluation Board.
Note 3: The device is not guaranteed to function outside its operating conditions.
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 5
SY8286A
Typical Performance Characteristics
Efficiency vs. Load Current Efficiency vs. Load Current
(VBYP=3.3V, MODE=Low) (VBYP=3.3V, MODE=High)
100 100
90
90
80
80 70
60
70
50
60
40
VIN=5V,VOUT=1.2V
50 VIN=12V,VOUT=1.2V 30
VIN=5V,VOUT=1.2V
VIN=19V,VOUT=1.2V 20 VIN=12V,VOUT=1.2V
40 VIN=23V,VOUT=1.2V VIN=19V,VOUT=1.2V
10 VIN=23V,VOUT=1.2V
30 0
0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10
90
90
80
80 70
60
70
50
60
40
VIN=5V,VOUT=1.8V
50 VIN=12V,VOUT=1.8V 30
VIN=5V,VOUT=1.8V
VIN=19V,VOUT=1.8V 20 VIN=12V,VOUT=1.8V
40 VIN=23V,VOUT=1.8V VIN=19V,VOUT=1.8V
10 VIN=23V,VOUT=1.8V
30 0
0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10
95 90
90 80
85 70
80 60
75 50
70 40
VIN=5V,VOUT=3.3V
65 30
VIN=12V,VOUT=3.3V VIN=5V,VOUT=3.3V
60 VIN=19V,VOUT=3.3V
20 VIN=12V,VOUT=3.3V
VIN=23V,VOUT=3.3V VIN=19V,VOUT=3.3V
55 10 VIN=23V,VOUT=3.3V
50 0
0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 6
SY8286A
95 90
90 80
85 70
80 60
75 50
70 40
VIN=7.4V,VOUT=5V
65 VIN=12V,VOUT=5V 30 VIN=7.4V,VOUT=5V
60 VIN=19V,VOUT=5V 20 VIN=12V,VOUT=5V
VIN=23V,VOUT=5V VIN=19V,VOUT=5V
55 10 VIN=23V,VOUT=5V
50 0
0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10
5.020 5.020
5.010 5.010
5.000 5.000
4.990 4.990
VIN=7.4V,VOUT=5V
4.980 4.980 VIN=7.4V,VOUT=5V
VIN=12V,VOUT=5V VIN=12V,VOUT=5V
VIN=19V,VOUT=5V VIN=19V,VOUT=5V
4.970 VIN=23V,VOUT=5V 4.970
VIN=23V,VOUT=5V
4.960 4.960
0.0 1.0 2.0 3.0 4.0 5.0 6.0 0.0 1.0 2.0 3.0 4.0 5.0 6.0
Output Current (A) Output Current (A)
5.020 5.020
5.010 5.010
5.000 5.000
4.990 4.990
4.980 4.980
IO=0.001A, VO=5V IO=0.001A, VO=5V
4.970 IO=3A, VO=5V 4.970 IO=3A, VO=5V
IO=6A, VO=5V IO=6A, VO=5V
4.960 4.960
6.0 11.0 16.0 21.0 23.0 6.0 11.0 16.0 21.0 23.0
Input Voltage (V) Input Voltage (V)
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 7
SY8286A
Load Transient Load Transient
(VIN=12V, VOUT=3.3V, IOUT=0.6-6A, MODE=Low) (VIN=12V, VOUT=3.3V, IOUT=0.6-6A, MODE=High)
I 5A/div
L IL 5A/div
∆Vo 20mV/div
∆Vo 20mV/div
VLX 5V/div
VLX 5V/div
IL 2A/div
IL 2A/div
IL 5A/div
IL 5A/div
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 8
SY8286A
Startup from VIN Shutdown from VIN
(VIN=12V, VOUT=3.3V, IO=6A) (VIN=12V, VOUT=3.3V, IO=6A)
IL 5A/div IL 5A/div
EN 5V/div EN 5V/div
IL 5A/div IL 5A/div
IL 5A/div IL 5A/div
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 9
SY8286A
Short Circuit Protection Short Circuit Protection
(VIN=12V, VOUT=3.3V, IO=0A~ Short, ILMT: Floating) (VIN=12V, VOUT=3.3V, IO=6A~ Short, ILMT: Floating)
IL 5A/div IL 5A/div
IL 5A/div
IL 5A/div
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 10
SY8286A
output inductor L and feedback resistors (R1 and R2) where Fsw is the switching frequency and IOUT,MAX is
need to be selected for the targeted applications the maximum load current.
specifications.
The SY8286A regulator IC is quite tolerant of different
Feedback resistor dividers R1 and R2: ripple current amplitude. Consequently, the final choice
of inductance can be slightly off the calculation value
Choose R1 and R2 to program the proper output voltage. without significantly impacting the performance.
To minimize the power consumption under light load, it
is desirable to choose large resistance values for bo h R1
2) The saturation current rating of the inductor must be
and R2. A value of between 10kΩ and 1MΩ is highly
selected to be greater than the peak inductor current
recommended for both resistors. If Vout is 1.2V,
under full load conditions.
R1=100k is chosen, then using following equat on, R2
can be calculated to be 100kΩ: VOUT (1-VOUT/VIN,MAX)
ISAT , MIN > IOUT ,MAX +
VOUT 2 ⋅ FSW ⋅ L
R1
3) The DCR of the inductor and the core loss at the
0.6V 0.6VFB switching frequency must be low enough to
achieve the desired efficiency requirement. It is
R2 = VOUT − 0.6V R1 . R2 desirable to choose an inductor with DCR<10mΩ
GND
to achieve a good overall efficiency.
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 11
SY8286A
Soft-start Light Load Operation Mode Selection
The SY8286A has a built-in soft-start to control the PFM or PWM light load operation is selected by MODE
output voltage ramp up speed during start up to limit the pin. Pull MODE pin low for PFM operation, and pull
input inrush current. The typical soft-start time is 1.3ms. this pin high for PWM operation.
CBS
100nF
Layout Design:
LX
The layout design of SY8286A regulator is relatively
simple. For the best efficiency and minimum noise
promblem, we should place the following components
VCC LDO and BYP Input close to the IC: CIN, CVCC, L, R1 and R2.
The 3.3V VCC LDO provides the power supply for 1) It is desirable to maximize the PCB copper area
internal control and drive circuit. Bypass this pin to connecting to GND pin to achieve the best thermal and
ground with a 2.2uF ceramic capacitor. The control and noise performance. If the board space allowed, a ground
drive circuit can also be powered by external 3.3V power plane is highly desirable.
supply. When a 3.3V external power supply is connected
to the BYP pin, the VCC LDO is turned off and the 2) CIN must be close to Pins IN and GND. The loop area
switch between BYP and VCC is turn d on. The overall formed by CIN and GND must be minimized.
efficiency may be improved by connecting the BYP pin
to external 3.3V switching power supply. Leave BYP pin 3) The PCB copper area associated with LX pin must be
floating if this feature is ot used. minimized to avoid the potential noise problem.
.
4) The components R1 and R2, and the trace connecting
to the FB pin must NOT be adjacent to the LX net on the
PCB layout to avoid the noise problem.
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 12
SY8286A
PCB Layout Suggestion
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 13
SY8286A
QFN3x3-20 Package Outline
Bottom view
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 14
SY8286A
Notes: All dimension in millimeter and exclude mold flash & metal burr.
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 15
SY8286A
Taping & Reel Specification
11.7/12.3
Feeding direction
Reel
Size
Package Tape width Pocket Reel size Trailer Leader length Qty per
type (mm) pitch(mm) (Inch) length(mm) (mm) reel
3. Others: NA
AN_SY8286A Rev. 0.9C Silergy Corp. Confidential- Prepared for Customer Use Only 16