Professional Documents
Culture Documents
com
Ϡ)Preliminary Specifications
(Ϡ
( )Final Specifications
Kelly Kao
_________________________________ ____________________________________
Eugene CC Chen
____________________________________
Reviewed By Project Leader
Alain Wu
____________________________________
Prepared By PM
Hubert Liu
____________________________________
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
7 INTERNATIONAL STANDARD
7-1 SAFETY
7-2 EMC
8 PACKING
9 PRECAUTION
9-5 STORAGE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Record of Revision
Version Date Page Description
0.1 2012/02/17 First release
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1. General Description
This specification applies to the 32.0 inch Color TFT-LCD Module T320XVN02.2. This LCD module has a TFT
active matrix type liquid crystal panel 1,366x768 pixels, and diagonal size of 32.0 inch. This module supports
1,366x768 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in
horizontal stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for
each dot.
The T320XVN02.2 has been designed to apply the 8-bit 1 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
* General Information
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
3. Electrical Specification
The T320XVN02.2 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT
array and liquid crystal. The other is to power Back Light Unit.
3.1.1: DC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC
Power Supply Input Current IDD -- 0.39 0.44 A 1
Power Consumption PC -- 4.68 5.28 Watt 1
Inrush Current IRUSH -- 3 A 2
Permissible Ripple of Power Supply Input Voltage VRP -- -- VDD * 5% mVpk-pk 3
LVDS Differential Input High Threshold Voltage VTH +100 -- +300 mVDC 4
Interface
Differential Input Low Threshold Voltage VTL -300 -- -100 mVDC 4
3.1.2: AC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
Receiver Clock : Spread Spectrum
Modulation range ʳ Fclk_ss ʳ Fclk
-3% ʳ -- ʳ Fclk
+3% ʳ MHzʳ 7
LVDS
Receiver Clock : Spread Spectrum
Modulation frequency ʳ Fss ʳ 30 ʳ --ʳ 200ʳ KHzʳ 7
Interface
Receiver Data Input Margin ʳ
Fclk = 85 MHz tRMG ʳ -0.4 --ʳ 0.4 ns ʳ 8
Fclk = 65 MHz ʳ -0.5 ʳ --ʳ 0.5 ʳ
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
*1'
μs
3. Test Condition:
(1) The measure point of VRP is in LCM side after connecting the System Board and LCM.
(2) Under Max. Input current spec. condition.
4. VICM = 1.25V
LVDS -
V IC M V TH
|V ID |
V TL
LVDS +
GND
|V ID |
0V
|V ID |
5. The measure points of VIH and VIL are in LCM side after connecting the System Board and LCM.
6. Input Channel Pair Skew Margin
Note: x = 0, 1, 2, 3, 4
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
)66
)FONB
)FONBVV
VVPD[
PD[
)FON
)FONB
)FONBVV
VVPLQ
PLQ
W5,3
W5,3
W5,3
W5,3
W5,3
W5,3
W5,3
/9'65[
5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[ 5[
,QSXW'DWD
/9'65[
,QSXW&ORFN 9GLII
9
)FON 7
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ÎNS
LVDS Option = High/OpenÎ
& OR FN
& + [B 5 5 * 5 5 5 5 5 5 *
& + [B
& + [B * * % % * * * * * %
& + [B
& + [B
& + [B % % '( 1$ 1$ % % % % '(
& + [B
& + [B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
ÎJEIDA
LVDS Option = LowÎ
3 UH YLR X V & \F OH & X UUHQ W& \FOH 1 H [ W& \FOH
& OR FN
&+ [B 5 5 * 5 5 5 5 5 5 *
&+ [B
&+ [B * * % % * * * * * %
&+ [B
G7
&+ [B
% % '( 1$ 1$ % % % % '(
&+ [B
&+ [B
&+ [B 5 5 1$ % % * * 5 5 1$
Note: x = 1, 2, 3, 4…
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1366 DCLK or less than 768 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
&+
'(
&/.
'(
'DWD
5*%
3L[HO
0
/LQH
3L[HO
0
1
3L[HO
0
7FON
3L[HO
0
,QYDOLG'DWD
7EONY
,QYDOLG'DWD
/LQH
3L[HO
7K
3L[HO
7Y
/LQH
3L[HO
3L[HO
/LQH
7GLVSK
7K
3L[HO
7GLVSY
3L[HO
/LQH
3L[HO
0
3L[HO
0
3L[HO
0
/LQH
1
7EONK
,QYDOLG'DWD
,QYDOLG'DWD
1 / LQ H
0SL[HO
3L[HO
3L[HO
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
W W W W W
W W
%DFNOLJKWRQ RII
FRQWUROVLJQDO
9%/2 1 *1'
&0 2 6,QWHUIDFH6LJQDO W W
/9' 6 B 6( /
* 1'
Values
Parameter Unit
Min. Type. Max.
t1 0.4ʳ ---ʳ 30ʳ ms
t2 0.1ʳ ---ʳ 50ʳʳ ms
t3 450ʳʳ ---ʳ ---ʳ ms
*1
t4 0 ʳ ---ʳ ---ʳ ms
t5 0ʳ ---ʳ ---ʳ ms
*2
t6 ---ʳ ---ʳ --- ʳ ms
t7 500ʳ ---ʳ ---ʳ ms
*3
t8ʳ 10 ʳ ---ʳ 50ʳ msʳ
t9ʳ 0ʳ ---ʳ ---ʳ msʳ
Note:
(1) t4=0 : concern for residual pattern before BLU turn off.
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
(3) When CMOS Interface signal is N.C. (no connection), opened in Transmitted end, t8 timing spec can be
negligible.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Spec
Item Symbol Condition Unit Note
Min Typ Max
ON 2 - 5.5 -
On/Off control voltage VBLON VDDB=24V VDC
OFF 0 - 0.8 -
External PWM
I_EPWM VDDB=24V - - 2 mADC -
Control Current
External PWM
F_EPWM VDDB=24V 140 180 240 Hz -
Frequency
ΰ к
Note 1 : Dimming ratio= 100% (MAX) Ta=25±5 , Turn on for 45minutes α
Note 2 : Measurement condition Rising time = 20ms (VDDB : 10%~90%);
Note 3 :For External PWM application, no backlight shutdown when 0% dimming hold time <10sec
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
CN3:CI0114M1HRL-NH (Cvilux)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
24V(typ.)
90% 90%
10% 10%
Power Input for BLU
(VDDB)
7 7 7 7 7
Valid Dimming
Control Signal
(V_IPWM,V_EPWM) 7
7
Dip condition
VDDB(typ.)*0.8
Value
Parameter Units
Min Typ Max
*1
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 - - ms
T8 - - 10 ms
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a
dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a
viewing angle of ij and ș equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 2400 3000 -- 1
2
Surface Luminance (White) LWH 280 350 -- cd/m 2
Luminance Variation įWHITE(9P) -- -- 1.33 3
Response Time (G to G) TȖ -- 6.5 -- ms 4
Color Gamut NTSC 72 %
Color Coordinates
Red RX 0.640
RY 0.330
Green GX 0.290
GY 0.600
Typ.-0.03 Typ.+0.03
Blue BX 0.150
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 5
x axis, right(ij=0°) șr -- 89 -- degree
x axis, left(ij=180°) șl -- 89 -- degree
y axis, up(ij=90°) șu -- 89 -- degree
y axis, down (ij=270°) șd -- 89 -- degree
Note:
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. From more information see FIG 2. When lamp current IH = 15mA. LWH=Lon5 where Lon5 is
the luminance with all pixels displaying white at center 5 location.
3. The variation in surface luminance, įWHITE is defined (center of Screen) as:
įWHITE(9P)= Maximum(Lon1, Lon2,…,Lon9)/ Minimum(Lon1, Lon2,…Lon9)
4. Response time 7 ӫʳ is the average time required for display transition by switching the input signal for five
luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
ӫ
7 is determined by 10% to 90% brightness difference of rising or falling period. (As illustrated)
The response time is defined as the following figure and shall be measured by switching the input signal for
“any level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
Photodetector
Output
T ӫ (F) T ӫ (R)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG3.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T320XVN02.2. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 760.0 mm
Vertical 450.0 mm
Outline Dimension
Depth (Dmin) 32.5 mm To rear
Weight 5,300 g
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Front View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Back View
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
(3) EN 60950 : 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical
Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology
Equipment Including Electrical Business Equipment.
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AU Optronics
(2) For RoHs compatible products, AUO will add RoHS for identification.
Note: The green Mark will be present only when the green documents have been ready by AUO internal green
team. (definition of green design follows the AUO green design checklist.)
B. Carton Label:
QTY : 4
7;91
;;;;;;;;;;
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4pcs Modules
” H ” Tape
Cushion set
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Specification
Total Packing
Item
Quantity Dimension Weight Remark
(kg)
Carton=1.79kg
1 Packing BOX 4pcs/box 832(L)mm*283(W)mm*545(H)mm 23.83kg
Cushion=2.04kg
2 Pallet 1 1150(L)mm*840(W)mm*132(H)mm 15kg
A. 4 boxes/pallet
3 Boxes per Pallet
B. 8 boxes/pallet
Panels per A. 16pcs/pallet
4
Pallet B. 32 pcs/pallet
Pallet after
A. 1150(L)*840(W)*677(H) A. 110.32kg
5 packing (40’ 56
B. 1150(L)*840(W)*1222(H) B. 205.64kg
container)
Stretch film
Corner angle
Pallet
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
12. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
(2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied
to module. And the case on which a module is mounted should have sufficient strength so that
external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit
broken by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the
surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials
like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the
adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 к and 35к at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com