Professional Documents
Culture Documents
Cytec Rtca 10683
Cytec Rtca 10683
TEST SPECIFICATIONS:
ENVIRONMENTAL CONDITIONS
AND
THE FOLLOWING ''MEETS'' Section 16, Section 17, Section 18, Section 19, Section 20, & Section 21
TEST PROCEDURE(S) OF THE ABOVE TEST SPECIFICATION
Test Configuration: 8x1 Nine Pole Multiplexer (Tested at 115 vac, 400 Hz)
Date of Tests: March 27, 29, 30, 31 and April 2, 3, 5, 6, & 7, 2004
NOTICE: “This report must not be used by the client to claim product endorsement by NVLAP or any
agency of the U.S. Government”. Please see the "Additional Description of Equipment Under Test" page
listed inside of this report. This report must not be reproduced (except in full), without the approval of
D.L.S. Electronic Systems.
Page -1-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SIGNATURE PAGE
Arnom C. Rowe
Test Engineer
EMC-001375-NE
Jack Prawica
Lab Manager
EMC-002412-NE
Brian J. Mattson
General Manager
Mail Order
CYTEC Corporation
Company Official:
CYTEC Corporation
Page -2-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -3-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -4-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -5-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -6-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -7-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -8-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -9-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -10-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -11-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -12-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
TABLE OF CONTENTS
i. Cover Page................................................................................................................................................ 1
ii. Signature Page ...................................................................................................................................... 2
iii. NVLAP Certificate of Accreditation .................................................................................................... 3
iv. NVLAP Scope of Accreditation ........................................................................................................... 4
v. Table of Contents................................................................................................................................ 13
1.0 Introduction......................................................................................................................................... 16
2.0 Test Equipment ................................................................................................................................... 16
3.0 Test Set-Up ......................................................................................................................................... 17
4.0 Operating Conditions of Test Sample................................................................................................. 18
5.0 Performance Monitored ...................................................................................................................... 19
6.0 Description of Test Sample................................................................................................................. 20
7.0 Additional Description of Equipment Under Test.............................................................................. 23
8.0 Photo Information and Test Setup ...................................................................................................... 24
9.0 Photos Taken During Testing ............................................................................................................. 25
10.0 References....................................................................................................................................... 26
11.0 Test Results..................................................................................................................................... 27
12.0 Conclusion of Immunity Tests........................................................................................................ 27
Page -13-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
TABLE OF CONTENTS
Page -14-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
TABLE OF CONTENTS
Page -15-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
1.0 INTRODUCTION:
On March 27, 29, 30, 31 and April 2, 3, 5, 6, & 7, 2004, a series of susceptibility tests was made to
demonstrate that the Ruggadized 9 Pole Switching Multiplexer, Model Number(s) RS/8-S-R
Mainframe, Serial Number 136906, manufactured by CYTEC Corporation, ''meets'' the emissions
and susceptibility requirements of RTCA/DO-160D, Change Number 2 (June 12, 2001),
Environmental conditions and Test Procedures for Airborne Equipment, using the following test
procedure(s): Section 16, Section 17, Section 18, Section 19, Section 20, & Section 21. The tests
were performed by personnel of D.L.S. Electronic Systems, Inc., who are responsible to Donald L.
Sweeney, Senior EMC Engineer.
This test report relates only to the items tested and contains the following number of pages:
A list of the test equipment used, along with identification and calibration data, is included in the
Table of each Appendix of this report. All primary equipment was calibrated against known
reference standards with a verified traceable path to NIST.
Page -16-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
All susceptibility tests were performed at D.L.S. Electronic Systems, Inc. The Ruggadized 9 Pole
Switching Multiplexer was placed on a non-conductive table. The following describes the various
Labs that are used for testing:
LAB B 20' long x 10' wide x 10' high double-walled, shielded enclosure (this shielded
enclosure is broken into two 10' x 10' x 10' identical size rooms).
LAB C 26' long x 16' wide x 16' high semi-ferrite lined enclosure.
LAB E 26' long x 16' wide x 16' high semi-ferrite lined enclosure.
LAB F 34' long x 24' wide x 13' high anechoic/ferrite tiled lined enclosure.
LAB H 20' long x 10' wide x 10' high screen shielded enclosure.
LAB J 21' long x 10' wide x 10' high screen shielded enclosure.
LAB K 16' long x 10' wide x 10' high screen shielded enclosure.
LAB L 20' long x 10' wide x 10' high ferrite tiled lined enclosure.
LAB M 20' long x 12' wide x 12' high screen shielded enclosure.
LAB Q* 36' long x 25' wide x 20' high screen shielded enclosure.
LAB R* 36' long x 25' wide x 20' high screen shielded enclosure.
LAB S* 36' long x 25' wide x 20' high screen shielded enclosure.
*Electromagnetic field absorbers were strategically placed according to Figure 21-7 of the
RTCA/DO-160 Standard. All lines leaving the room were filtered. The load banks were located
outside the main room. The shielded load bank room measured 6' x 6' x 8'.
Page -17-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
All test measurements were made at a laboratory temperature of 72°F at 40% humidity with the
following mode of operation:
Loop communication was established from external PCU to the “I/O Signal” Port on the EUT and
than from Port “O” to external PCU. RS-232 communication was continued during the tests.
Page -18-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The RS-232 communication cable was monitored during all of the performed tests. Any
interruptions in data flow would be considered abnormal.
Page -19-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
6.1 DESCRIPTION:
Page -20-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Corcom 5EFLA2S
Clock Frequencies:
11.0592 MHz
Page -21-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page - 22 -
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
I certify that the above, combined with paragraph 6.0, describes the equipment tested and that the equipment
will be manufactured as stated.
by________________________________________ ____________________________________
Signature Title
for________________________________________ ____________________________________
Company Name Date
Page -23-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -24-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -25-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10.0 REFERENCES:
Page -26-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The Ruggadized 9 Pole Switching Multiplexer was subject to the test procedure(s) Section 16,
Section 17, Section 18, Section 19, Section 20, & Section 21. A detailed explanation of how these
tests and their measurements were made is shown in Appendix(es) A-G at the end of this report.
The Ruggadized 9 Pole Switching Multiplexer, Model Number(s) RS/8-S-R Mainframe, ''meets''
RTCA/DO-160D (July 29, 1997), Environmental conditions and Test Procedures for Airborne
Equipment using test procedure(s) Section 16, Section 17, Section 18, Section 19, Section 20, &
Section 21. See the Appendix(es) A-G for a detailed explanation of the test results.
Page -27-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX A
RTCA/DO-160D
SECTION 16
Power Input
Page -28-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test defines the test procedures for the electrical input power applied to the terminals of the
equipment under test.
When equipment requires only AC input power and is tested to the AC input parameters, the
equipment is identified as Category E.
Page -29-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The AC Voltage Surge test set up as shown in Figure 16-3 is shown below:
Page -30-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
For voltage and frequency, single phase equipment was operated according to the test procedures in
paragraph 16.5.1.1b. The equipment was operated at a maximum duty cycle for at least 30 minutes
with the primary power adjusted to 122 Vrms at 420 Hz. The voltage was then decrease to 100 Vrms
at 380 Hz with the duty cycle set at the maximum for 30 minutes.
For voltage and frequency, single phase emergency electrical system equipment was operated at
maximum duty cycle for 30 minutes with the primary power adjusted to 100 Vrms at 360 Hz. Then
the test was repeated with voltage adjusted to 122 Vrms at 360 Hz for 30 minutes. The test was then
set up with the voltage adjusted to 122 Vrms at 440 Hz with a maximum duty cycle for at least 30
minutes. After 30 minutes the voltage was decreased to 100 Vrms at 440 Hz with a maximum duty
cycle
Page -31-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
For voltage and frequency, three phase equipment was operated according to the test procedures in
paragraph 16.5.1.1c. The equipment was operated at a maximum duty cycle for at least 30 minutes with the
primary power adjusted to 120.5 Vrms at 420 Hz. The voltage was then decrease to 101.5 Vrms at 380 Hz
with the duty cycle set at the maximum for 30 minutes.
For voltage and frequency, three phase emergency electrical system equipment was operated at
maximum duty cycle for 30 minutes with the primary power adjusted to 101.5 Vrms at 360 Hz. Then
the test was repeated with voltage adjusted to 120.5 Vrms at 360 Hz for 30 minutes. The test was
then set up with the voltage adjusted to 120.5 Vrms at 440 Hz with a maximum duty cycle for at
least 30 minutes. After 30 minutes the voltage was decreased to 101.5 Vrms at 440 Hz with a
maximum duty cycle
For voltage modulation, the equipment under test was operated according to the test procedures in paragraph
16.5.1.2 using the limits from Figure 16-1, the modulation envelope was applied for two minutes with the
voltage modulation set at 3.5 volts maximum peak-to-valley difference between the minimum and the
maximum voltage.
For frequency modulation, the equipment under test was operated according to the test procedures in
paragraph 16.5.1.3 defined by Figure 16-2, the modulation envelope was within the narrow frequency limits
and occurs as a result of speed variations in a generator coupling and drive speed regulation. The variations
of the primary system frequency, due to frequency modulation during any two-minute period was within a
band about the mean frequency as shown in Figure 16-2.
For momentary power interruptions, the equipment under test was operated according to the test procedures
in paragraph 16.5.1.4 using the test conditions from Table 16-1. The equipment under test was fully
operational with the nominal voltage and frequency applied prior to each test condition. The test conditions
from Table 16-1 was repeated twice for each operating mode of the equipment.
For normal Surge Voltage (AC), the equipment was set up as shown in Paragraph 16.5.1.5, Figure
16-3. The equipment under test was operated at a voltage 115V rms ±1 Vrms for five minutes. The
voltage is then cycled three times from 115 Vrms to 160 Vrms ±2Vrms for 30 minutes, returning the
voltage to 115 Vrms for five seconds. Then the voltage is decrease to 60 Vrms.
Page -32-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
For AC:
The frequency components of the voltage modulation envelope waveform does not exceed
the limits of Figure 16-1. The equipment was subjected to the above test conditions and
operates within the applicable equipment performance standards.
Page -33-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The variations of primary system frequency due to the frequency modulation does remain
within a band about the mean frequency defined by Figure 16-2.
Page -34-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The envelope of equipment step function of AC voltage surges does remain within the limits
defined by Figure 16-5.
Page -35-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The test conditions in Table 16-1 was applied twice to each operating mode of the equipment
under test.
Page -36-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.2 RESULTS:
Page -37-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 16
Page -38-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -39-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -40-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -41-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -42-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -43-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 16
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -44-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX B
RTCA/DO-160D
SECTION 17
Voltage Spike
Page -45-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test determines whether the equipment can withstand the effects of voltage spikes arriving at
the equipment on its power leads, either AC or DC. The main adverse effects to be anticipated are:
Category A
Equipment intended primarily for installation where a high degree of protection against damage by
voltage spikes is required is identified as Category A.
Page -46-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The transient generator used produced the waveform shown in Figure 17-1 of the test specification.
A typical test setup is shown in Figure 17-2. Any method of generating the spike may be used if the
waveform complies with Figure 17-1. The generator was inserted in series with the Ruggadized 9
Pole Switching Multiplexer.
Page -47-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
With the equipment under test disconnected, the transient wave shape was verified to be within
specification. The Ruggadized 9 Pole Switching Multiplexer was set to its designated voltage. A
series of positive and negative spikes (described in Figure 17-1 of the Standard) were injected to
each of the primary inputs of the equipment under test. A minimum of 50 transients of each polarity
were injected within a period of one minute. The test was repeated for each operating mode or
function of the equipment.
In order to thoroughly test AC power lines, the pulse positioning function of the Spike Generator
was used. The generator was connected to the same 400 Hz power source as the power input line
under test in order to sync to the line. Using the Pulse Position Control in conjunction with the
Polarity Reversing Switch, the spike was injected through the entire 360° of the sine wave. The
generator injects at a rate of 6.2 pulses per second when set to sync to 400 Hz lines, resulting in
372 pulses in 60 seconds.
Page -48-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
FIGURE 17-1
5.2 RESULTS:
The AC Power Line was tested with no problems found at these levels.
Page -49-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160C
Section 17
Page -50-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -51-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160C
Section 17
Page -52-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -53-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -54-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -55-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -56-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -57-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -58-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160C
Section 17
Page -59-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -60-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -61-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
Page -62-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
IMPEDANCE VERIFICATION
Page -63-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -64-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 17
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -65-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 17
TEST EQUIPMENT
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Spike Generator Solar 7054-1 980705 2x10us
600V
Pulse Solar 2201-1 DLS# 2x10us
Transformer 000386 600V
Capacitor DLS JSU23X NA 10 uF
230V
Isolation Hammond 171E DLS# 115 Vac
Transformer 000396
Resistor DLS DLS50 N/A 50 Ohms
Assembly ½ Watt
Page -66-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX C
RTCA/DO-160D
SECTION 18
Page -67-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test determines whether the equipment will accept frequency components of a magnitude
normally expected when the equipment is installed in the aircraft. These frequency components are
normally harmonically related to the power source fundamental frequency.
When equipment requires only AC input power and is tested to the AC input parameters, the
equipment is identified as Category E.
Page -68-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -69-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
For AC:
The equipment was set up as shown in Figure 18-1, Paragraph 3.0. A sine wave audio frequency
signal was applied successively in series with each ungrounded AC input power lead. The frequency
of the applied signal was varied between 750 Hz and 15 kHz.
Page -70-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The amount of voltage injected over the frequency range is shown below:
For AC:
The rms amplitude of the signal was maintained at not less than five percent of the nominal
AC input voltage. While injecting the signal, compliance with the standard was determined.
5.2 RESULTS:
The AC Power Line was tested with no problems found at this level.
Page -71-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 18
Page -72-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Freq(Hz) 30W Cal - Gen Setting 115VACLimit (Vp-p) Level Applied (Vp-p) Suscept./Threshold 30W (Y or N)
750 20.05 16.3 16.3 None N
800 19.99 16.3 16.3 None N
900 19.98 16.3 16.3 None N
1000 19.88 16.3 16.3 None N
2000 19.84 16.3 16.3 None N
3000 19.69 16.3 16.3 None N
4000 19.63 16.3 16.3 None N
5000 19.61 16.3 16.3 None N
6000 19.63 16.3 16.3 None N
7000 19.75 16.3 16.3 None N
8000 19.65 16.3 16.3 None N
9000 19.65 16.3 16.3 None N
10000 19.64 16.3 16.3 None N
11000 19.76 16.3 16.3 None N
12000 19.62 16.3 16.3 None N
13000 19.78 16.3 16.3 None N
14000 19.75 16.3 16.3 None N
15000 19.85 16.3 16.3 None N
Page -73-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 18
Page -74-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
4.24 VOLTS ACROSS .6 OHMS = 30 WATTS
Page -75-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 18
Page -76-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -77-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -78-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
6.0 AUDIO FREQUENCY POWER INPUTS PHOTOS TAKEN DURING TESTING: (CON’T)
Page -79-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 18
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -80-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 18
TEST EQUIPMENT
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Audio Isolation Solar 6220-1A DLS# 10 Hz – 250 kHz
Transformer 000392
Power Isolation Hammond 171E DLS# 115v, 50/60 Hz
Transformer Manufacturing 000396
Calibration/ DLS CSVR 0506 DLS# .6 Ohms
Impedance 000711
Verification
Resistor
Power DLS RA18 DLS# 200 Hz – 150 kHz
Resistor 000707
Assembly
Capacitor Mallory SPU25Z106 N/A 10 uF
AQSD
Digital Multi- Wavetek 2005 000707435 DC – 1 kHz
Meter
Page -81-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX D
RTCA/DO-160D
SECTION 19
Page -82-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test determines whether the equipment interconnect circuit configuration will accept a level of
induced voltages caused by the installation environment. This section relates specifically to
interfering signals related to the power frequency and its harmonics, audio frequency signals, and
electrical transients that are generated by other on-board equipment or systems and coupled to
sensitive circuits within the EUT through its interconnecting wiring.
Category C
Equipment intended primarily for operation in systems where interference-free operation is required
and where severe coupling occurs due to long wire runs or minimum wire separation is identified as
Category C.
Page -83-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This section consists of four different configurations: 1) Magnetic Fields Induced Into the
Equipment; 2) Magnetic Fields Induced into Interconnecting Cables; 3) Electric Fields Induced into
Interconnecting Cables; and 4) Spikes Induced into Interconnecting Cables.
The Magnetic Field induced into the equipment consisted of a straight wire radiator located within
0.15m of the periphery of the equipment under test. The field generated is shown in Table 19-1.
19.3.2 Magnetic fields I x L = 30 A-m at I x L – 18 A-m Not applicable I x L – 120 A-m from
induced into 400 Hz reducing from 380 to 420 Hz 380 to 420 Hz, and 60
interconnecting to 0.8 A-m at 15 A-m at 400 Hz
cables kHz (as shown in reducing to 1.6 A-m at
Figure 19-1(a)) 15 kHz (as shown in
Figure 19-1(a))
19.3.3 Electric fields V x L –1800 V-m V x L – 360 V-m Not applicable V x L – 5400 V-m
induced into from 380 to 420 from 380 to 420 Hz from 380 to 420 Hz,
interconnecting Hz and 5400 V-m at 400
cables Hz reducing to 135
V-m at 15 kHz (as
shown in Figure
19-1(b))
19.3.4 Spikes Figure 19-4 Figure 19-4 Figure 19-4 Figure 19-4
induced into L = 3.0m L = 3.0m L = 1.2m L = 3.0m
interconnecting
cables
Table 19-1
Page -84-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -85-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -86-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -87-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -88-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The Audio Frequency Magnetic Fields are shown in Figure 19-1(a) using Category C:
The Audio Frequency Electric Fields are shown in Figure 19-1(b) using Category C:
Page -89-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
5.2 RESULTS:
The AC Power Line was tested with no problems found at this level.
Page -90-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Page -91-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Section 19.3.1
Page -92-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Arms-m) Limit for 3m (Arms) Measured I (Arms) Susceptibility/Threshold
0.38 120 40 40 None
0.39 120 40 40 None
0.4 120 40 40 None
0.41 120 40 40 None
0.42 120 40 40 None
Section 19.3.2
CONTROL
Page -93-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Arms-m) Limit for 3m (Arms) Measured I (Arms) Susceptibility/Threshold
0.38 120 40 40 None
0.39 120 40 40 None
0.4 120 40 40 None
0.41 120 40 40 None
0.42 120 40 40 None
Section 19.3.2
O Output
Page -94-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Arms-m) Limit for 3m (Arms) Measured I (Arms) Susceptibility/Threshold
0.38 120 40 40 None
0.39 120 40 40 None
0.4 120 40 40 None
0.41 120 40 40 None
0.42 120 40 40 None
Section 19.3.2
SIGNAL I/O
Page -95-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Vrms-m) Limit for 3m (Vrms) Measured V (Vrms) Susceptibility/Threshold
0.38 5400 1800 1800
0.39 5400 1800 1800
0.40 5400 1800 1800
0.41 5400 1800 1800
0.42 5400 1800 1800
Section 19.3.3
CONTROL
Page -96-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Vrms-m) Limit for 3m (Vrms) Measured V (Vrms) Susceptibility/Threshold
0.38 5400 1800 1800
0.39 5400 1800 1800
0.40 5400 1800 1800
0.41 5400 1800 1800
0.42 5400 1800 1800
Section 19.3.3
O Output
Page -97-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Results: Record any susceptibility noted and the threshold level or enter "None"
List any additional ranges and thresholds of susceptibility noted throughout the sweep
Freq. (kHz) Limit (Vrms-m) Limit for 3m (Vrms) Measured V (Vrms) Susceptibility/Threshold
0.38 5400 1800 1800
0.39 5400 1800 1800
0.40 5400 1800 1800
0.41 5400 1800 1800
0.42 5400 1800 1800
Section 19.3.3
SIGNAL I/O
Page -98-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Cable Bundle Under Test: Control L - Radiator Wire Length (m): 3.0
Positive Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.3
Burst Duration (microseconds) 50 to 1000 270
Duration of Test (minutes) >2 2:10
Negative Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.8
Burst Duration (microseconds) 50 to 1000 238
Duration of Test (minutes) >2 2:10
Section 19.3.4
CONTROL
Page -99-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Positive Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.3
Burst Duration (microseconds) 50 to 1000 268
Duration of Test (minutes) >2 2:10
Negative Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.8
Burst Duration (microseconds) 50 to 1000 267
Duration of Test (minutes) >2 2:10
Section 19.3.4
O OUTPUT
Page -100-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Positive Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.3
Burst Duration (microseconds) 50 to 1000 345
Duration of Test (minutes) >2 2:10
Negative Polarity
Spike Parameter Specification Applied
Voltage Spike Amplitude (Vp-p) >600 >600
Spike Repetition Period (microseconds) .2 to 10 1.8
Burst Duration (microseconds) 50 to 1000 282
Duration of Test (minutes) >2 2:10
Section 19.3.4
SIGNAL I/O
Page -101-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.1
Page -102-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.1
Page -103-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -104-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.2
Page -105-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.2
Page -106-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CONTROL CABLE
Page -107-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
O OUTPUT
Page -108-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SIGNAL I/O
Page -109-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.3
Page -110-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.3
Page -111-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CONTROL CABLE
Page -112-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
O OUTPUT
Page -113-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SIGNAL I/O
Page -114-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.4
Page -115-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.4
Page -116-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
TOTAL DURATION POSITIVE
Page -117-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
TOTAL DURATION NEGATIVE
Page -118-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
REPETITION RATE POSITIVE
Page -119-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
REPETITION RATE NEGATIVE
Page -120-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
REPETITION PERIOD POSITIVE
Page -121-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
REPETITION PERIOD NEGATIVE
Page -122-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
DURATION AND AMP POSITIVE
Page -123-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CALIBRATION
DURATION AND AMP NEGATIVE
Page -124-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 19.3.4
Page -125-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
POSITIVE
CONTROL
Page -126-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
NEGATIVE
CONTROL
Page -127-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
POSITIVE
O OUTPUT
Page -128-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
NEGATIVE
O OUTPUT
Page -129-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
POSITIVE
SIGNAL I/O
Page -130-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CATEGORY C
NEGATIVE
SIGNAL I/O
Page -131-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.1
Page -132-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
CONTROL
Page -133-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
O OUTPUT
Page -134-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
SIGNAL I/O
Page -135-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.3
CONTROL
Page -136-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.3
O OUTPUT
Page -137-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.3
SIGNAL I/O
Page -138-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.4
CALIBRATION
Page -139-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.4
CONTROL
Page -140-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
O OUTPUT
Page -141-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.4
SIGNAL I/O
Page -142-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.1
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -143-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.1
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Current Hevi-Duty H522F3A DLS# 380 – 15 kHz
Step-Up 000397 20:1
Transformer
Straight Wire N/A N/A N/A AWG8
Radiator
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -144-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
TABLE 3
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -145-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.2
TABLE 4
Model Serial
Description Manufacturer Number Number Range
Current Hevi-Duty H522F3A DLS# 380 – 15 kHz
Step-Up 000397 20:1
Transformer
Magnetic Field N/A N/A N/A AWG8
Radiating Wire
Page -146-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.3
TABLE 5
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -147-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.3
TABLE 6
Model Serial
Description Manufacturer Number Number Range
Audio Isolation Solar 6220-1A DLS# 10 Hz – 250 kHz
Transformer 000393
High Voltage Transco 4B15N3-02 DLS# 125:1
Transformer 000395
Impedance Solar 7033-1 DLS# 30 Hz – 150 kHz
Matching 000394
Transformer
Radiating Wire NA NA NA 3.5 meter AWG 24
Page -148-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.4
TABLE 7
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -149-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 19.3.4
TABLE 8
Page -150-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX E
RTCA/DO-160D
SECTION 20.4
Conducted Susceptibility
10 kHz – 400 MHz
Page -151-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test determines whether the equipment under test will operate within performance specifications
when the equipment and its interconnecting wiring are exposed to a level of RF modulated power by
injection probe induction onto the power lines and interface circuit wiring.
From 10 kHz to 400 MHz, the equipment under test (EUT) is subjected to RF signals coupled by
means of injection probes into its cable bundles.
Equipment with special signal, frequency, modulation or bandpass characteristics may require test
variations as specified by the applicable performance standards.
The result of this test is to permit categories to be assigned defining the conducted and RF test levels
of the equipment. This test, along with the radiated susceptibility, is sufficient to obtain
environmental qualification for radio frequency susceptibility of the equipment. Additional tests may
be necessary to certify the installation of systems in an aircraft dependent on the functions performed.
Page -152-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Categories designate the RF test levels and establish the EUT minimum RF susceptibility level. The
categories may be given in the applicable equipment performance standard.
The category to be applied to a system or equipment frequently must be chosen before the internal RF
environment of the aircraft is known. Further, many systems or equipments are designed with the
intent that they will be installed in several different types of aircraft. Therefore, if a category is not
identified in the equipment specification, the equipment manufacturer should design, test and qualify
the equipment to the category level consistent with expected location, exposure and use.
Category designation for equipment consists of three characters. Conducted susceptibility test levels
are designated with the first category character. Continuous wave (CW) and square wave (SW)
modulated radiated susceptibility test levels are designated with the second category character. Pulse
modulated radiated susceptibility test levels are designated with the third category character.
To aid the equipment manufacturer in selecting appropriate test limits for the equipment and its
interconnecting wiring, categories have been defined below. The descriptions are for guidance only.
Equipment location, anticipated exposure and location of interconnecting wiring, aircraft size and
construction determine the test level.
Page -153-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The Ruggadized 9 Pole Switching Multiplexer is set up according to Figure 20-9 shown below. The
induced current monitor probe is installed 5cm from the EUT. If the EUT connector plus backshell
length exceeds 5cm, the probe shall be placed as close to the connector backshell as possible and the
position noted. Support and center the probe. Install the injection probe 5cm from the face of the
monitor probe.
Page -154-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Proper probe locations, software installation, modes of operation and stability of the EUT, test
equipment and all monitoring circuits and loads were established.
Set the signal generator to 10 kHz, unmodulated. Establish the forward power to the injection probe
on amplitude measurement instrument #2 at 10 kHz at the power determined in the probe calibration
procedure for the selected category of Figure 20-6. The frequency range was scanned slowly at the
proper forward power. Both CW and square wave modulation were applied. The RF carrier was
amplitude modulated with a 1 kHz square wave at greater than 90 percent depth, with optional 1 to 3
Hz superimposed. When modulation was applied, the peak amplitude complies with the definitions
of Figure 20-5.
Also consider applying other modulations associated with the EUT, such a clock, data, IF, internal
processing or modulation frequencies. Consider any possible low frequency response characteristic
of the EUT, for example, a flight control equipment's response to 1 to 3 Hz modulation in the 2 to 30
MHz HF range. When using 1 Hz to 3 Hz modulation, ensure that sweeping and/or frequency
stepping is suspended during the "off" period of the modulation. As an option, tests can be run using
only the modulation to which the EUT is most susceptible.
Slowly scan the frequency range to 400 MHz at the forward power amplitude using the proper probes
and modulations. Dwell at internal modulation, data or clock frequencies, as required.
Monitor the induced cable bundle current with the amplitude measurement instrument and data
recorder to capture resonances. When necessary, adjust and control the forward power to limit
induced current on the bundle:
Cat Y – 1 A;
Cat W – 500 mA;
Cat V – 250 mA;
Cat U and R – 100 mA;
Cat T – 25 mA
Cat S – 5 mA
While scanning, evaluate EUT operation and DETERMINE COMPLIANCE WITH APPLICABLE
EQUIPMENT PERFORMANCE STANDARDS.
Page -155-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -156-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The Ruggadized 9 Pole Switching Multiplexer was subjected to Category V. The level is shown
below in Figure 20-6.
5.2 RESULTS:
The AC Power Line was tested with no problems found at this level.
Page -157-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 20.4
CONDUCTED SUSCEPTIBILITY
Page -158-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 "A C C a b le " C W 0 4 -0 3 -0 4
1000
100
10
T e s t C u rre n t (m A )
C a lib ra tio n c u rre n t L im it (m A )
M a x im u m C u rre n t L im it (m A )
0 .1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z)
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 "A C C a b le " C W 0 4 -0 3 -0 4
100
10
L a b S c a lib ra tio n fo rw a rd p o w e r le v e l (d B m )
1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z)
Page -159-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 " A C C a b le " C W 0 4 -0 3 -0 4
100
10
C a lib ra tio n le v e l (m A )
L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F r e q u e n c y (H z )
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 " A C C a b le " C W 0 4 -0 3 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
Page -160-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
100
10
Page -161-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 "0 " C W 0 4 -0 2 -0 4
1000
100
10
T est C urrent (m A )
C alibration current Lim it (m A )
M axim um C urrent Lim it (m A )
0.1
10000 100000 1000000 10000000 10000 0000 1000000000
F req u en cy (H z)
Page -162-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 "0 " C W 0 4 -0 2 -0 4
100
10
L a b S c a lib ra tio n fo rw a rd p o w e r le v e l (d B m )
1
1 0 0 00 1 0 0 00 0 1 00 0 00 0 1 0 0 00 0 00 1 00 0 00 0 0 0 1 00 0 00 0 0 00
F re q u e n c y (H z)
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " 0 " C W 0 4 -0 2 -0 4
100
10
C a lib ra tio n le v e l (m A )
L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
Page -163-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " 0 " C W 0 4 -0 2 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F r e q u e n c y (H z )
100
Page -164-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
10
Page -165-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
1
Test Current (m A)
Calibration current Lim it (m A)
M axim um Current Lim it (m A)
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
10
Page -166-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " S ig n a l I/O " C W 0 4 -0 2 -0 4
100
10
C a lib ra tio n le v e l (m A )
H S L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
C Y T E C R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 D 9 " S ig n a l I/O " C W 0 4 -0 2 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
Page -167-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
100
Amplitude (mA)
10
Page -168-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
100
10
1
Test C urrent (m A )
C alibration current Lim it (m A )
M axim um C urrent Lim it (m A )
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
Page -169-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
CYTEC RS /8 -S M a infr a m e
S N 1 3 6 9 0 6 D2 5 " Control Conne c tor" CW 0 4 -0 3 -0 4
100
Amplitude (dBm)
10
C Y T E C R S /8 - S M a in f r a m e
SN 1 3 6 9 0 6 D 2 5 " C o n tr o l C o n n e c to r " C W 0 4 -0 3 -0 4
100
Amplitude (mA)
10
C a lib ra t io n le ve l (m A )
L a b S m e a s u re d c a lib ra t io n le ve l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
Fr e q u e n c y ( Hz )
Page -170-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C YT EC R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 D 2 5 " C o n tr o l C o n n e c to r " C W 0 4 -0 3 -0 4
1000
Amplitude (dBuV)
100
C a lib ra t io n L a b S L e ve ls (d B u V )
C a lib ra t io n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
Fr e q u e n c y ( Hz )
CYTEC RS/8-S M ainfr am e
SN 136906 D25 "Co ntr ol Con ne ctor " CW 04-03-04
1000
Amplitude (dBuA)
100
Page -171-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
10
1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
Page -172-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
1
Test Current (m A)
Calibration current Lim it (mA)
Maxim um Current Limit (mA)
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
10
Page -173-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 " A C C a b le " S W 0 4 -0 3 -0 4
100
10
C a lib ra tio n le v e l (m A )
L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F r e q u e n c y (H z )
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 " A C C a b le " S W 0 4 -0 3 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
Page -174-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
100
10
Page -175-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
100
10
Test Current (m A)
Calibration current Lim it (m A)
M axim um Current Lim it (m A)
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
Page -176-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " 0 " S W 0 4 -0 2 -0 4
100
10
C a lib ra tio n le v e l (m A )
L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
Page -177-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " 0 " S W 0 4 -0 2 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z )
100
Page -178-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
10
Page -179-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
10
Test C urrent (m A )
C alibration current Lim it (m A )
M axim um C urrent Lim it (m A )
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
C Y T E C R S /8-S M a in fra m e
S N 13 6 90 6 D 9 "S ig n a l I/O " S W 04 -0 2-0 4
100
10
Page -180-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fra m e
S N 1 3 6 9 0 6 D 9 " S ig n a l I/O " S W 0 4 -0 2 -0 4
100
10
C a lib ra tio n le v e l (m A )
L a b S m e a s u re d c a lib ra tio n le v e l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
F re q u e n c y (H z)
C Y T E C R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 D 9 " S ig n a l I/O " S W 0 4 -0 2 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F r e q u e n c y (H z )
Page -181-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100
100
10
Page -182-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
100
10
1
Test C urrent (m A )
Calibration current Lim it (m A )
M axim um Current Lim it (m A )
0.1
10000 100000 1000000 10000000 100000000 1000000000
Frequency (Hz)
Page -183-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10
C YT EC R S /8 -S M a i n fra m e
S N 1 3 6 9 0 6 D 2 5 "C o n tro l C o n n e c to r" S W 0 4 -0 2 -0 4
100
Amplitude (mA)
10
C a lib ra t io n le ve l (m A )
L a b S m e a s u re d c a lib ra tio n le ve l (m A )
1
10000 100000 1000000 10000000 100000000 1000000000
Fr e q u e n c y ( Hz )
Page -184-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
C Y T E C R S /8 -S M a in fr a m e
S N 1 3 6 9 0 6 D 2 5 " C o n tr o l C o n n e c to r " S W 0 4 -0 2 -0 4
1000
100
C a lib ra tio n L a b S L e v e ls (d B u V )
C a lib ra tio n L im it (d B u V )
10
10000 100000 1000000 10000000 100000000 1000000000
F r e q u e n c y (H z )
100
Page -185-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
10 0
10
10
Page -186-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
AC CABLE
Page -187-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
D9 INPUT PORT
Page -188-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
D9 SIGNAL I/O
Page -189-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -190-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 20.4
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -191-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 20.4
TEST EQUIPMENT
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Amplifier Amplifier 50W 23419 80 MHz – 400 MHz
Research 1000A
Amplifier Amplifier 150A100 14331 10 kHz – 80 MHz
Research
RF Coupler Amplifier DC6180 303130 80 MHz – 400 MHz
Research
RF Coupler Amplifier DC2035 301080 10 kHz – 80 MHz
Research
Software Dell Dimension N/A 10 kHz – 400 MHz
Computer L100R
RF Injection Solar 9142-1N 945013 80 MHz – 400 MHz
Probe
RF Injection Solar 9144-1N 974512 10 kHz – 80 MHz
Probe
Page -192-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX F
RTCA/DO-160D
SECTION 20.5
Radiated Susceptibility
100 MHz – 18 GHz
Page -193-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
This test determines whether equipment will operate within performance specifications when the
equipment and its interconnecting wiring are exposed to a level of RF modulated power by a radiated
RF field.
For frequencies between 100 MHz and the upper frequency limit, the Ruggadized 9 Pole Switching
Multiplexer is subjected to radiated RF fields.
Equipment with special signal, frequency, modulation or band pass characteristics may require test
variations as specified by the applicable performance standards.
The result of this test is to permit categories to be assigned defining radiated RF, along with the
conducted test levels of the equipment. These tests are sufficient to obtain environmental qualification
for radio frequency susceptibility of the equipment. Additional tests may be necessary to certify the
installation of systems in an aircraft dependent on the functions performed.
Page -194-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Categories designate the RF test levels and establish the EUT minimum RF susceptibility level. The
categories may be given in the applicable equipment performance standard.
The category to be applied to a system or equipment frequently must be chosen before the internal RF
environment of the aircraft is known. Further, many systems or equipments are designed with the
intent that they will be installed in several different types of aircraft. Therefore, if a category is not
identified in the equipment specification, the equipment manufacturer should design, test and qualify
the equipment to the category level consistent with expected location, exposure and use.
Category designation for equipment consists of three characters. Radiated susceptibility test levels are
designated with the first category character. Continuous wave (CW) and square wave (SW) modulated
radiated susceptibility test levels are designated with the second category character. Pulse modulated
radiated susceptibility test levels are designated with the third category character.
To aid the equipment manufacturer in selecting appropriate test limits for the equipment and its
interconnecting wiring, categories have been defined below. The descriptions are for guidance only.
Equipment location, anticipated exposure and location of interconnecting wiring, aircraft size and
construction determine the test level.
Category V is intended for equipments and interconnecting wiring installed in a moderate environment
such as the more electromagnetically open areas of an aircraft composed principally of metal.
Page -195-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
The Ruggadized 9 Pole Switching Multiplexer shall be set up according to Figure 20.2 shown below.
Signal generators, amplifiers, antennas and probes shall maintain required RF field levels to properly
illuminate the EUT and interconnecting wiring. Position and aim antennas to establish the RF field
strengths at the EUT and interconnecting wiring. When the beam width of the antenna does not totally
cover the EUT and wiring, perform multiple area scans. Directly expose apertures in the EUT to the
transmitting antenna, which may require additional LRU orientations. Vertical and horizontal antenna
orientations are required for polarized antennas.
Page -196-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Establish appropriate antenna and isotropic probe locations, software installation, modes of operation
and stability of the EUT, test equipment and all monitoring circuits and loads.
Use the forward power settings determined from the radiated field calibration. When modulation is
applied, ensure that the peak amplitude complies with the definitions of Figure 20-5.
Scan the frequency range to the upper frequency limit using the proper antennas and modulations.
Dwell at internal modulation, data and clock frequencies, as required.
While scanning, evaluate EUT operation and DETERMINE COMPLIANCE WITH APPLICABLE
EQUIPMENT PERFORMANCE STANDARDS.
Page -197-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -198-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The Ruggadized 9 Pole Switching Multiplexer was subjected to Category V as shown in Figure
20-10 below:
FIGURE 20-10
5.2 RESULTS:
Page -199-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 20.5
RADIATED SUSCEPTIBILITY
Page -200-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
Page -201-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
100.0M 1.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
100.0M 1.0G
Frequency
Page -202-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -203-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -204-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -205-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -206-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 20.5
RADIATED SUSCEPTIBILITY
Page -207-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
Page -208-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
100.0M 1.0G
Frequency
Page -209-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -210-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -211-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -212-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
100.0
90.0
80.0
70.0
Amplitude (dBm)
60.0
50.0
40.0
30.0
20.0
Calibrated Forward Power
10.0 Test Forward Power
0
1.0G 10.0G
Frequency
Page -213-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 20.5
RADIATED SUSCEPTIBILITY
Page -214-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
Page -215-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
100.0M 1.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
100.0M 1.0G
Frequency
Page -216-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -217-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -218-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -219-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -220-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 20.5
RADIATED SUSCEPTIBILITY
Page -221-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
Page -222-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
100.0M 1.0G
Frequency
Page -223-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -224-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -225-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -226-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
250.0
225.0
200.0
175.0
Amplitude (V/m)
150.0
125.0
100.0
75.0
50.0
0
1.0G 10.0G
Frequency
Page -227-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -228-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -229-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -230-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -231-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -232-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -233-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -234-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -235-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -236-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 20.5
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -237-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 20.5
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Field Monitor Amplifier FM5004 302153 NA
Research
Amplifier Amplifier 1000W 22243 100 – 1000 MHz
Research 1000M7
TWT Amplifier Amplifier 200T1G3A 301643 800 MHz –
Research 2.8 GHz
TWT Amplifier Amplifier 200T2G8A 301027 2.5 GHz –
Research 7.5 GHz
TWT Amplifier Amplifier 200T8G18A 301107 7.5 GHz –
Research 18 GHz
RS Dell Dimension N/A N/A
Computer L1000R
Test Software Quantum Rev 2.28 N/A N/A
(T.I.E.)
Log Antenna Amplifier AT1230 23709 80 – 230 MHz
Research
Tripod Amplifier TP1000A 301946 N/A
Research
Large Horn Amplifier AT4000 22305 200 – 1000 MHz
Antenna Research
Medium Horn Amplifier AT4002A 301759 800 MHz –
Antenna Research 5 GHz
Small Horn Amplifier AT4003 301597 4 – 8 GHz
Antenna Research
Page -238-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
APPENDIX G
RTCA/DO-160D
SECTION 21
Page -239-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
These tests determine that the equipment does not emit undesired RF noise in excess of the levels
specified below. The notches specified in the radiated emissions limits are included to protect aircraft
RF sensors operating frequencies.
Categories are defined in terms of location and separation between the equipment and aircraft radio
antennas. As these parameters are widely linked to aircraft type and size, some examples are given
with each category definition.
The Ruggadized 9 Pole Switching Multiplexer was subjected to Category M. A 7 dB relaxation limit
was applied to the Category L limits on the Integrated Drive Generator (IDG) Output Feeder wires
from 150 kHz to 500 kHz.
Page -240-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -241-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Conducted RF Emission:
a. Interference currents generated by the equipment and measured by using a clamp-on interference
measuring device within the frequency ranges and in excess of the values given in Figure 21-1 shall
not appear on any power line normally connected to an aircraft bus.
Line Impedance Stabilization Networks (LISNs) shall be used as shown in Figure 21-3. Power return
wires tied locally to the ground plane as noted in RTCA/DO-160C/D Section 20.3a(6) are not tested.
b. Interference currents on interconnecting cable bundles other than antenna feed cables and
primary power lines shall be measured by using a clamp-on interference measuring device.
The limits and frequency ranges are as shown in Figure 21-2.
Figure 21-3 shows a simplified test arrangement for the use of the current probe.
Install the current probe five centimeters from the EUT. If the EUT connector plus backshell length
exceeds five centimeters the probe shall be placed as close to the connector backshell as possible and
the position noted.
Radiated RF Emission:
Radiated interference fields generated by the equipment within the frequency ranges, and in excess of
the values shown in Figures 21-4 for the appropriate categories, shall not be radiated from any unit,
cable or interconnecting wiring. A typical arrangement of equipment for conducting the radiated RF
emission test is shown in Figure 21-7.
NOTE:
Subsection 21.4 does not measure or control spurious signals conducted out of the antenna terminals
of receivers and transmitters. That control should be specified in the equipment performance standard
for that receiver or transmitter.
Page -242-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
General Requirements:
The equipment under test shall be set up on a ground plane and operated in accordance with the
criteria in Subsection 20.3 subparagraph a and parts 1, 2 and 5 of subparagraph b, with the following
additions:
a. Interference shall be measured using the peak detector function of the interference measuring
equipment. Interference measuring instruments with selectable IF bandwidths (BWI) may be used,
and the selected BWI must be the values given in the following table. The time constant of the
peak detector must be lower or equal to 1/BWI. Where applicable, video bandwidths shall be
selected to be greater than or equal to the resolution bandwidth.
Note: During radiated tests the above bandwidths may not provide a low enough noise floor to make
proper measurements in the notches defined for categories M & H. In that case, a 10 kHz BWI
shall be used for measurements in the notches with no correction factor being applied.
b. Field strength units are obtain by using any appropriate antenna and adding the appropriate antenna
factor to the measured voltage in dB microvolts. Appropriate correction factor for cable losses and
matching networks must also be applied.
c. When linearly polarized antennas are used for radiated tests above 25 MHz, measure radiated
emissions using both vertically and horizontally polarized orientations.
d. For EUT with multiple apertures and sensors such as displays, several different orientations may be
required, for example connector side and aperture side(s) facing the antenna.
f. Radiated ambient data (EUT "off" and test support equipment "on") is required only if EUT
emissions are greater than 3 dB below the selected category limit. It is good engineering practice to
check ambient radiated emissions prior to a radiated emissions test, and it is desirable that the
ambient emissions be at least 6 dB below the selected limit line.
g. Measure and record the EUT emissions conditions and apply the appropriate limit from Figures 21-
4 for the selected category.
Page -243-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The maximum level of conducted RF interference on the power lines is shown in Figure 21-1 using
Category M:
The maximum level of conducted RF interference on interconnecting cables is shown in Figure 21-2
using Category M:
Page -244-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
The maximum level of radiated RF interference is shown in Figure 21-4 & Figure 21-5 using
Category M:
Page -245-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
5.1 LIMITS:
5.2 RESULTS:
Page -246-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 21
Page -247-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 21
Page -261-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
RTCA/DO-160D
Section 21
Page -270-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
AC POWER
Page -285-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
D9 PORT 0
Page -286-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -287-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
D25P CONTROL
Page -288-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SETUP 1
Page -289-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SETUP 2
Page -290-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SETUP 3
Page -291-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
2 MHz TO 25 MHz
Page -292-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -293-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -294-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -295-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -296-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -297-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
Page -298-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 21.3
CONDUCTED RF EMISSIONS
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -299-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 21.3
CONDUCTED RF EMISSIONS
TEST EQUIPMENT
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Computer Packard Bell 204CD N351041092 N/A
Page -300-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 21.4
RADIATED RF EMISSIONS
TEST INSTRUMENTATION
TABLE 1
All primary equipment is calibrated against known reference standards with a verified traceable path NIST.
Page -301-
Company: CYTEC Corporation
Model Tested: RS-8-S-R Mainframe
Report Number: 10683
SECTION 21.4
RADIATED RF EMISSIONS
TEST EQUIPMENT
TABLE 2
Model Serial
Description Manufacturer Number Number Range
Coaxial Cable Pasternack RG223-U N/A 10 kHz – 1 GHz
Page -302-