Professional Documents
Culture Documents
OF LIFTING EQUIPMENT
defgh
THIS REPORT COMPLIES WITH THE REQUIREMENTS OF THE LIFTING OPERATIONS AND LIFTING EQUIPMENT
REGULATIONS 1998
Address Km 1 Via Siberia-Cota, Centro Empresarial, Los Robles IV Bodega 7, Cota, Cundinamarca, COLOMBIA
Safe Working
Serial Number Description of Equipment Proof Load
Load
Z08012.01 (Z06919.05D) 5 Ton S.W.L. Low Headroom Hoist 5 Ton 6.25 Ton
836-03299 (ZX064-3SoLM5K031-LHR0001-46060U14)
I hereby declare that the equipment described in this record has been correctly tested and thoroughly examined in accordance with
the appropriate provisions and is safe to use once it has been properly installed.
EC Declaration of Conformity
We hereby declare that the equipment described in this record has been correctly tested and thoroughly examined in accordance
with the appropriate provisions and is safe to use.
The Street Crane product described above has been designed in accordance with the following provisions:-
Safety of Machinery Directive, 2006/42/EC.
Low Voltage Directive, 2006/95/EC.
EMC Directive, 2004/108/CU.
Harmonised standards EN ISO 12100, Parts 1 and 2, Safety of Machinery.
BS EN 60204-1 Safety of Machinery, Electrical equipment for machines.
BS EN 60204-32, Safety of Machinery, Requirements for hoisting machines.
BS EN 61000-6-2 EMC, generic immunity standard.
BS EN 61000-6-4 EMC, generic emissions standard.
BS EN 14492-2, Cranes - Power driven hoists.
National standard BS 2573 Part 2, Rules for the design of cranes.
As required by the Machinery Directive, the CE symbol has been attached to the equipment and the technical file has been
compiled in accordance Annex VII, Part B and is held at the manufacturers address. National Authorities may make reasoned
written requests for access to sections of the technical file.
Street Crane Company Limited, Town End Works, Chapel‐en‐le‐Frith, High Peak, SK23 0PH
Tel +44 (0) 1298 812456 Fax +44 (0) 1298 814945 e‐mail admin@streetcrane.co.uk web www.streetcrane.co.uk
DQA‐0202
END OF LINE TEST REPORT defgh Sheet 1 of 2
DQA-00256 ZX6/8
Hoist Revision Rv-6 LH Leg Range (mm) 100-500mm Crab Gauge N/A
Hoist Type LH WITH ROLLER Control Voltage (V) 110V CONTROL IP Rating IP 54
Hoist Motor IP Rating IP 55
Power Supply (V) 460V SUPPLY CT Motor IP Rating IP 55
Additional Features C/T INVERTER CONTROLLED (ramp & hold). STD.COLLECTOR BRKT.
Part No Serial No GR No
Hoist Motor 300-411 15052361001019 S18615/G71649 SCC LINE PULL LOAD TEST Casting Serial No
Hoist Gearbox 826-200 F60378 01-16-009 Ratio 99:1 Line Pull Load 1.625 Ton Drive C1 BN 141203
Hoist Brake 340-311 13208881 S20780/G73205 Coil Voltage (DC) 180V Size 12 (46Nm) Non Drive C2 BN 140903
Hoist Brake Rectifier 340-591 PMB 400-S N/A Type 270V AC 0.75A full wave rectifier Barrel Side C3 BN 150402
Traverse Drive 300-11931 22568564 S21901/G77528 Brake Torque (NM) 5Nm Voltage 460V Barrel Side C4 BN 150402
Second Traverse Drive NA N/A N/A Brake Torque (NM) NA Voltage NA Sheave C5 BN 14031-A807
Barrel Length 826-140-1 Foot Hole CRS (mm) LONG BARREL Sheave C6 BN 14031-E866
Operational YES Anchor C7 BN 14031-G802
Rope 620-831 S22894 G77108 Rope Certificate # 170396 Rope Condition GOOD Anchor C8 BN 14031-G803
Bottom Block/Hook 820-531 S22920-R332/4 G77715 Rope Falls 4 Bottom Block Condition GOOD Rope Socket C9 BN N204
Control Panel 820-8741 Brake & Wheel Circlips Fitted YES
Electrical Schematic Std. 025-4446 Overload 820-8651
Special Electrical No. Of Springs Required 14
Schematic if required N/A No. Of Springs Required in Parallel 2
Electrical Schematic No. Of Stacks 7
Preload Setting (tonne) 0.51
Factory (switch point) Setting (tonne) 0.75
Preload Stack Height (mm) 27.03
FALSE Factory Load Stack Height (mm) 25.94
Votage Supplied (VAC) 460V Frequency (Hz) 60Hz Ambient Temp (ºc) 19 Electrical Device Settings
Wheel Allignment: Drive Side (mm) <1 Wheel Allignment: Non-Drive (mm) <1 AC Rectifier Voltage: VAC 223 Device Set To
Cycle Brake Temps: less than 125ºc 50 Cycle Motor Temp: less than 60ºc 33 DC Rectifier Voltage: VDC 199 Cross Travel Fast to Slow Timer Not Set
Radial Motor CPLG F Up/Down: mm/s RMS 1.3/1.0 Radial Gbox CPLG F Up/Down: mm/s RMS 3.7/2.4 Axial Gearbox CPLG Fast Up/Down: mm/s 1.9/1.6 Hoist Slow to Fast Timer 0.5 secs
Axial Brake Shaft F Up/Down: mm/s RMS 2.6/2.4 ** "C" Dimension 825 Brake Clearance Gap (mm) 0.3 Hoist Supply Transformer 460V
Rope Speed in Fast (m/min) 20.14 Rope Speed in Slow (m/min) 6.75 Hoist Motor Slow (amps) 2.9/2.9/2.9 Phase Failure Relay 460V
#Full Load Hoist Lifting Speed in Fast (m/min) 4.8 #Full Load Hoist Lifting Speed in Slow (m/min) 1.61 Hoist Motor Fast (amps) 2.2/2.2/2.0
CSA Flash Test DQA-0177: completed by N/A Motor Oscillation: max tolerance 5mm 0.2 Hoist Motor Power Fast/Slow in HPs 6/1.9
Traverse Drive Speed m/min 2.21/20.43 Motor Name Plate Power Fast/Slow in HPs 0.34 Brake Fastener Torque Check Torques Confirmed Set
NA NA NA NA
Street Crane Co. Limited, Chapel-en-le-Frith, High Peak, SK23 0PH, United Kingdom - Tel: +44 (0) 1298 812456 - www.streetcrane.co.uk
END OF LINE TEST REPORT defgh Sheet 2 of 2
DQA-00256 ZX6/8
Hoist Revision Rv-6 LH Leg Range (mm) 100-500mm Crab Gauge N/A
Hoist Type LH WITH ROLLER Control Voltage (V) 110V CONTROL IP Rating IP 54
Hoist Motor IP Rating IP 55
Power Supply (V) 460V SUPPLY CT Motor IP Rating IP 55
IMPORTANT PLEASE NOTE:- REMOVE THE RUBBER PLUG FROM THE TRAVERSE DRIVE GEARBOX BREATHER, BEFORE HOIST OPERATION!
Street Crane Co. Limited, Chapel-en-le-Frith, High Peak, SK23 0PH, United Kingdom - Tel: +44 (0) 1298 812456 - www.streetcrane.co.uk
HOOK BLOCK CERTIFICATE defgh
Date of Report 29/06/2017 Report Number: HBC-Z0801201 (Z06919.05D)
The components described above are intended to be incorporated into machinery covered by the Machinery
Directive 2006/42/EC they must not be put into service until the final machine, into which these components are to be
incorporated, has been declared to be in conformity with the provisions of the Machinery Directive 2006/42/EC and
any national legislation.
Street Crane Company Limited, Town End Works, Chapel‐en‐le‐Frith, High Peak, SK23 0PH
Tel +44 (0) 1298 812456 Fax +44 (0) 1298 814945 e‐mail admin@streetcrane.co.uk web www.streetcrane.co.uk
DQA‐0265
WIRE ROPE CERTIFICATE defgh
Date of Report 29/06/2017 Report Number: WRC-Z0801201
The components described above are intended to be incorporated into machinery covered by the Machinery Directive
2006/42/EC they must not be put into service until the final machine, into which these components are to be incorporated,
has been declared to be in conformity with the provisions of the Machinery Directive 2006/42/EC and any national
legislation.
Street Crane Company Limited, Town End Works, Chapel‐en‐le‐Frith, High Peak, SK23 0PH
Tel +44 (0) 1298 812456 Fax +44 (0) 1298 814945 e‐mail admin@streetcrane.co.uk web www.streetcrane.co.uk
DQA‐0266