Professional Documents
Culture Documents
TV BRAND
CODE
(Series of IC Program)
Disassemble the original remote
AIWA
Press the blank button on the keypad VolUp
Press and hold the MENU button on the TV panel
AKARI Press the SLEEP button once on the remote, then press again until the service mode menu appears
Use the Ch-Up/Ch-Down button to select the factory type, and the Vol-Up/Vol-Down button to adjust the data value
Press the AV button on the remote
Press the MENU button
AKIRA
Press the QUICK VIEW button
Press the MUTE button (Use the TIMER button to move the menu, and Vol-Up/Vol-Down buttons to adjust the data values)
TV on standby position
CRYSTAL
Press and hold the Vol-Up & Vol-Down button until TV Turns ON
Unloading the original remote
FUJITEC
Press 1x hidden button (located just below the Vol-Down), then press it again to move to the next menu
FTC-5166 Use the Ch-Up/Ch-Down buttons to move to the next sub-menu, and the Vol-Up/Vol-Down buttons to adjust the data value
GOLDSTAR On the TV panel, Press simultaneously the buttons MENU + Vol-Up + Vol-Down + Ch-Down
Turn off the TV with the ON/OFF switch on the TV panel or Unplug the TV power cable
HITACHI
Press and hold the AV button on the TV panel
Fujian
Turn on the TV with the power switch TV (AV button is still on hold until the tv turn on)
Method 1:
Press and hold the OSD/DISPLAY button
Press the PICTURE button (standard VSM)
JVC Method 2:
On the remote, press and hold the buttons OSD/DISPLAY + INFO + MUTE
Method 3:
On the remote, Press and hold the buttons OSD/DISPLAY + INFO + CINEMA/GAME
Unloading the remote kk-y237b (Both the original or not)
KONKA Cut ic line number 7, then cut also line system buttons on the left, cut off the end "charcoal col" and then jumper with pin 7
K1438C ,2199C Press the SYSTEM button to enter the service mode system
Press the MUTE button to move to the next mode
LG Method 1:
Flatron Press and hold the OK button on the remote
Press the OK button on the TV panel (both are on hold for about 5 seconds)
Method 2:
Press the MENU button on the remote, press again and hold
Press the MENU button on the TV panel (both on hold for about 5 seconds)
LG Press the MENU button on the remote, press again and hold
Ultra Slim Press the MENU button on the TV panel
PANASONIC Short (Connecting a moment) pin "FA1" to "FA2" or Short "TP8" to "GROUND"
Method 1:
Reduce the volume to 0
Set the timer/sleep at position 30 minutes
Press and hold the DISPLAY button
Press Vol-Down on the panel (exit from service menu press the Normal button on the remote)
Method 2:
PANASONIC Reduce the volume to 0
Set the timer/sleep at position 30 minutes
TX Series
Press the DISPLAY button on the remote, press again and hold
Press the button Vol-Down on the TV panel
Use the 1 buttons and 2 to select the page /group setting, buttons 3 and 4 to select an item, buttons Vol-Up/Vol-Down to
change the value
To exit press the NORMAL button on the remote
Method 3:
Connect momentarily pin FA1 to FA2 or TP8 to ground
Cari Titik TPE 1 dan TPE 2 dengan tulisan SERVICE dibagian Bawah PCB, letaknya Berada diantara tombol Menu panel depan
dan kaki sensor remote
Connect the two points (TPE1 & TPE2) with using the button
PANASONIC Turn on the TV then press the newly button created earlier as much as 2x
TC-14S22M Press the MENU button on the TV panel / the F button on the Remote to display some of the parameters to will be adjusted,
then use the VOLUME button to change the E2PROM value parameter
To exit from Service Mode, press the button that made earlier so until it appear on the screen writings MK yellow, then press
the N button on the remote
Method 1:
Press and hold the Vol-Up, then press Ch-Down
To exit press the STANDBY/POWER button
PHILIPS
Method 2:
TV on standby position
Press on the remote sequence number 06259 and then press the MENU buttons
POLYTRON TV on standby position
Press and hold the MENU button on the remote until the password confirmation appears
Enter the code 1013/1014/1206/1207/1208/1209 to acces on the SERVICE MODE
Digitec To default settings enter the code 3101
For navigation and setting the data use the Channel and Volume buttons
Press the MENU button on the remote to save the settings
Turn off the TV with the ON/OFF switch on the TV panel or Unplug the TV power cable
Press and hold the VT (blue button) on the remote
RCA / SABA / THOMSON Turn on the TV with the ON/OFF switch on the TV panel or Plug the TV power cable
Note:
For some models, press the button again VT
Method 1:
TV on standby position
On the remote, Press in sequence the buttons DISPLAY + PSTD + MUTE + POWER
SAMSUNG Method 2:
TV on standby position
On the remote, Press in sequence the buttons INFO + MENU + MUTE + POWER
Press the POWER button to exit the Service Menu
SAMSUNG
On the remote, Press in sequence the buttons PIC.OFF + DISPLAY + MENU + MUTE + PIC. ON
Chasis KS3A
SAMSUNG TV on standby position
Zoom Vision On the remote, Press in sequence the buttons PSTD + HELP + SLEEP + POWER
Method 1:
TV on standby position
On the remote, Press in sequence the buttons DISPLAY + MENU + MUTE + POWER
Method 2:
SAMSUNG
TV on standby position
Plano
On the remote, Press in sequence the buttons MENU + PSTD + MUTE + POWER
Method 3:
TV on standby position
On the remote, Press in sequence the buttons MUTE + 182 + POWER
Method 1:
Press and hold the MENU button on the remote
Press the Vol-Up button on the TV panel
Method 2:
Press and hold the MENU button on the TV panel, then press the number 1/2/3/9 in remot
SANYO For navigation and setting the data, use the Channel and Volume / MUTE-TIMER buttons
To exit press the MENU button on the remote (the data will automatically be stored)
Method 3:
Turn off the TV with the ON/OFF switch on the TV panel or Unplug the TV power cable
Press and hold the VolDown (Do not removable)
Turn on the TV with the ON/OFF switch on the TV panel or Plug the TV power cable
To exit/save the data press the MENU
Method 4:
Press and hold thel VolDown button on the TV panel
Press TELETEXT (Green) button on the remote
The number button to select the sub-menu
For navigation and setting the data, use the Channel and Volume buttons
To exit press the keys that are not used
Method 5:
Press the MENU button on the remote, press “quickly” the Vol-Up button on the TV panel
For navigation and setting the data, use the Channel and Volume buttons
Method 6:
Press the MEMORI button on the TV panel, then press “quickly” the MENU/MEMORY buttons on the remote
Use the SOUND-SET button on the remote to navigation
Method 7:
Press the MENU button on the remote
Press the DISPLAY button 3x
For navigation and setting the data, use the Channel and Volume buttons
SANYO Press the DISPLAY button to exit
Method 8:
Press and hold the FUNCTION button on the remote
Press the Ch-Up button on the TV panel
For navigation and setting the data, use the Channel and Volume buttons
To exit turn off the TV with ON/OFF switch on TV panel
Method 9:
Press and hold the MENU button on the TV panel
Press the Vol-Up button on the remote
For navigation and data adjust, use the Timer/Mute and Volume buttons
Press the MENU button to exit
Replace the new memory ICs (empty):
Turn on the TV
SANYO Press and hold the TV/AV button on the TV panel about 2 second, then will appear the words "CLR"
Press the Ch-Up button on the TV panel
Memory initialization to be completed until posts appear number "1"
SANYO Press and hold the MENU button on the TV panel
Dynamic Press the number button 1 or 2 on the remote
Method 1 :
Cari sebuah switch NORMAL – SERVICE (Bentuknya mirip switch yang digunakan pada bagian vertical), letaknya dekat dengan
TUNER
Untuk masuk service mode – pindah ke posisi SERVICE
Method 2 :
Turn on the TV
Make sure the image adjustment NORMAL position (not in the zoom/wide)
Connect the JA137 and JA138 for about 1 second and then just off again
Use the Channel and Volume buttons to navigation and adjust the value data
To exit turn off the TV
Replace the new memory ICs (empty):
Turn off the TV
Connect JA137 & JA138
SHARP Turn on TV
Wait about 30 seconds automatically default data will be written into memory
Method 3:
Press the MENU button on the remote
Then press the numbers 4,7,2,5
Use the Channel and Volume button to navigation and adjust the data value
To exit turn off the TV
Method 4:
Connect shortly PIN 6 & PIN 7 on the IC MCU (TDA 98XXX). To exit connect again
Method 5:
Press the MENU button, then select the FEATURE, then select the BLUE BACK to ON position
Press and hold -/-- button about 5 second
Enter the password 1,3,7,9
Press the Vol-Up button to turn-off SERVICE MODE
SHARP Turn on the TV
Slim dengan UOC kotak Make sure the picture adjustment is NORMAL position (with remote)
Short pin-5 Mikrokontrol sekitar 1 detik dan lepas kembali atau JA483 dengan JA484)
Press the MENU button to select the Sub-Menu (Adjust Mode, Check mode, Option mode. etc)
For navigation and setting the data, use the Channel and Volume
Wait about 4 seconds before moving to another adjustment So that data is automatically saved
Replace the new memory ICs (empty):
Turn off the TV
Connect pin-5 Mikrokontrol to ground (or JA483 by JA484)
Turn on the TV
Wait about 30 seconds automatically default data will be written into memory
If the default data fail - it may be caused by ABL brightnes too bright or there is a problem in the ABL
SHARP
Connect the two jumper (J800) near tuner
Expression
Method 1:
Connect the moment two jumper (J122 - J124)
SHARP Metode 2:
Wonder Universe Turn off the TV with the switch ON/OFF on the TV panel or Unplug the TV power cable
Press and hold the Vol-Up & Ch-Up buttons together (Do not removable)
Turn on the TV with the ON/OFF switch on the TV panel or Plug the TV power cable
Method 1:
TV on standby position
On the remote, Press in sequence the buttons OSD/Display + 5 + VolDown + Power
SONY Method 2:
Turn off the TV with the switch ON/OFF on the TV panel or Unplug the TV power cable
Press and hold the Vol-Up & Ch-Up buttons together (Do not removable)
Turn on the TV with the ON/OFF switch on the TV panel or Plug the TV power cable
Method 1:
Press and hold the DISPLAY button on the remote
Press and hold the Vol-Down button on the TV panel about 3 seconds
Method 2:
Reduce the volume to 0
Press and hold the Vol-Down button on the TV panel
Press the DISPLAY button on the Remote
TCL
Note :
Never change the data on the key "6", Because it can cause various problems or TV can not work as it should
Initialization :
Go into service mode
On the remote, press the numbers buttons 0,7,5,2
Initialization is only necessary if you want to change the data to the factory DEFAULT value
Then it should proceed with the adjustment geometry and white-balance
Press the DISPLAY button simultaneously and VSM On TV panel
TCL
For navigation and setting the data, use the Menu/Channel and Volume buttons
Chassis M11 (M37221M4-322SP)
Press the DISPLAY button to save the settings and exit from Service mode
TCL
Chassis 5N11STV5348/ TV on standby position
T-A5 S3C8849X15-AQB7 (S3P8849XZZ-AQB9) Press and hold the Vol-Up & Vol-Down buttons on the TV panel
(24C08IC/NN5198 (NN5099)
Press the MUTE button on the remote and press it again and hold
TOSHIBA
Press the MENU button on the TV panel
TOSHIBA
Press the MENU button on the TV panel. And on the remote, press the numbers buttons 4,7,2,5
28W23B
Method 1:
Reduce the volume to 0
Press the DISPLAY button on the remote
Press and hold the Vol-Down button on the TV panel
Press the DISPLAY button on the remote again
Method 2:
CHINES TV Press the MENU button on the remote 2x
Press the DISPLAY button
Press the MUTE button
Metode 3:
Press the MENU button on the remote 2x
Press the QUICK-VIEW button
Press MUTE button
7461 Jumper pin 2 and pin 16 on the IC Program
Reduce the volume to 0
Press and hold the Vol-Down button on the panel tv
Press the DISPLAY button on the remote, it will display the letter "S". Repeat these steps until the letter "D"
8873CPANG-6F53 Press the MENU button on the panel tv / on the remote to enter into F.MENU 0 to F.MENU 11 as well as setting the B / W
BALANCE
Use the buttons Ch-Up/Ch-Down & Vo-lUp/Vol-Down to choose Item & Adjust the value data
To SAVE/EXIT from service mode turn off the tv
8873CSCNG-6PR6 Press and hold the Vol-Down button on the TV panel and press the DISPLAY button on the remote until it says "FACTORY"
Press the DISPLAY button once to enter the B/W setting
Press the DISPLAY button one more time to get into F1 settings / press the number keys 0-7 to enter the settings menu
Use the Ch-Up/Ch-Down & Vo-lUp/Vol-Down to select items and adjust the data value
To SAVE/EXIT press DISPLAY button on the remot
Press the MENU button
8893 Enter the code 6,4,8,3
(Mono – STR – 250CH) ENTER DISPLAY
ENTER DISPLAY=AGAIN CHART PRESS MUTE BUTTON
Reduce the volume to 0
Press and hold the Vol-Down button on the TV panel
8800CPN-3GV1 244KJ Press the CALL buttons will be appears mode "S"
Repeat the above steps until appears mode "D"
Press the MENU button to select the opsi
Reduce the volume to 0
Press and hold the button Vo-lDown on the TV panel
87CK38N-1H74 + TB1238
Press the OSD/DISPLAY botton on the remote to enter the mode “S”. Repeat these steps to enter the mode “D”
Press the Power button on the remote to save setting result/exit
Reduce the volume to 0
Press and hold the button Vol-Down on the TV panel
LC863532A-5Z00
Press the OSD/DISPLAY on the remote to enter the mode S
Press the POWER button on the remote to save setting result /exit
Press the DISPLAY button on the remote
Press the MUTE button 3x
LC863528B-51C3 Use the SLEEP button to move the page. Ch-Up/Ch-Down button to select the menu. Vol-Up/ VolDown button to adjust the
data value
Press the MENU button to save/exit
Reduce the volume to 0
LC863328A-5Y29, 5Y28, 5Y19 Press and hold the Vol-Down
Press the number 0 on the remote 3x
Reduce the volume to 0
LC863528B-52K7 Press the MENU button 5x (go to channel edit menu), select EXCHANGE PROGRAM, then press the number 2483
Use the QUICK-VIEW button to move the page
Press the MENU button
LC863532B-52H8
On the remote, Press in sequence the number button 8,8,8
Reduce the volume to 0
Press the MENU button
LC863532B-55L1 (WCOM)
On the remote, Press in sequence the numbers buttons 6,5,6,8
Use the DISPLAY button to move the page
LC863320A-C81DC Cari tombol kosong di remot yang tidak dipakai. Gunakan tombol Ch-Up/Ch-Down untuk pindah ke menu berikutnya , dan tombol Vol-Up/Vol-Down
LA863328A-5028/2MD0 untuk adjust
LC863324A-5T51 Go to the menu and select Auto Program/Auto Search
LC8633528B-50S8 On the remote, Press in sequence the numbers buttons 6,4,8,3 to enter the service menu
M37220M3-167SP Then press again on the remote in sequence the numbers buttons 6,4,8,3 to enter the factory mode
Press the MENU button
M37160M8-058FP + M61266
On the remote, Press in sequence the numbers buttons 6,4,8,3
Press and hold the MENU button on the TV panel
On the remote, Press in sequence the numbers buttons 6,4,8,3
M37220M3-010SP + M52340SP
Use the Ch-Up/Ch-Down button to select menu. VolUp/VolDown button to adjust the data value. And the button Power for
save/exit
Press the MENU button
On the remote, Press in sequence the numbers buttons 6,4,8,3
M37160M8-058FP + M61266(SMD)
Use the Mute button to move the page. Ch-Up/Ch-Down to select Menu. Vol-Up/Vol-Down button to adjust the value data
Press the POWER/STANDBY button to save/exit
Press the MUTE button
Press the PP button
M37160M8-073FP(SMD)
Press the button -/-- to move pages
Press the "TV" button to exit
Turn on the TV
ST92195C7B1/MIF
Select the MENUFEATURE
ST92195C7B1/PFT
E nter the code 3
Set the volume/balance up to RS03
TH-50J2-3RR0
Press the Menu button, then press the Mute
On the remote, press in sequence the buttons CLOCK + PM + TIMER + DISP
TDA9384PS/N2/31FM-OSD
On the remote, press the numbers buttons 0-9 to select theMENU
Press the MUTE button on the remote, then press and hold the MUTE button again
TMP87CK38N Press the MENU button on the TV panel
Repeat the above steps until the letter "D" appears on the TV screen
Reduce the volume to 0 with Vol-Down button on the TV panel. Then press the DISPLAY button on the remote
TMP87PS38N Repeat the above steps until the letter "D" appears on the TV screen
Use the Menu button to move pages, and Vol-Up/Vol-Down to adjust the value data
UСom ST6-ELAME2 Press the Skip + Vol-Down + Fine Tune button