Professional Documents
Culture Documents
NH (H.R.C) FUSES:
They have been produced according to TS EN 60269 standard. Federal knife fuses are
produced from steatite materials and are capable of breaking the short-circuit voltages up
to 120 kA. Spring contacts of the knife fuse base plates those have been produced from
electrolytic copper in five separate dimensions from steatite or BMC material according to
the Customer, have been supported by special steel springs in addition to its own clamping
and spring back features. They have been produced also as dual-indicator
INSTALLATION CONTACTORS:
They have been producing for the control of power distribution, lighting application at the
housings and industrial plants, small-sized motors and control of the installation, according
to IEC 60947-4-1 standard and CE norms, as 20A, 40A and 63A.
POWER CAPACITORS:
Federal capactors are produced; according to TS EN 60831-1/2 standards; by applying MKP
technology in order to collect the electricity load and to provide the capacitive reactance in
alternative current circuits. They have been marketed in mono-phase and tri-phase types,
from 2,5kVAr to 50kAVr. .
CURRENT TRANSFORMERS:
According to TS 620 EN60044-1 and IEC 60044-1 standards; they are produced in order
to supply measurement devices, counters, relays and other devices, operating with similar
techniques. Federal Current Transformers have the feature of Sealing. Rated current is from
30A to 4000A.
CONTACTORS:
They are manufactured according to IEC 60947-4-1 and TS EN 60947-4-1 standards and
in comply with. It is possible to produce them from 6A to 750A. They enable for remote
control of, especially electrical motors, and the power plants such as compensation heating
through cables. When they are used together with thermic relays, they protect the devices
and the plants against over-load currents. There are coils available for AC and DC control
voltage.
THERMAL RELAYS:
In case of over-load and phase failure, it inactivates the motor by contact. It is produced
according to TS EN 60947-4-1, IEC 60947-4-1 standards and CE, up to 93A, as composed
against ambient temperature.
SMART RELAYS:
It is designed for executing two separate tasks. Its first task is to warn the user against the
failures those are not instantaneous within the system to which it is attached, are invisible
for the user during their formation time, however increasing by time and bring the system
to standstill. The second task is to protect the system against the failures those are
instantaneous and cause deformation of the system unless they are removed within the
possible shortest time (over-current, phase cut-off, unbalance phase, etc.). Noticing the
electrical and mechanical failures well in advance, it is a device preventing the production
losses. It notices the failures by measuring the vibration occurred by the damages on the
bearings.
HARMONIC FILTERS:
It is a circuit element which prevent reaching and became bigger of harmonic voltage and
current compenents to the capacitor damage in the system. According to filter power
terminal clamps or busbar connection in output, ( Iln =1,3 In) (saturation current Iln)
Protection IP00, heat protect with thermocontact (120°C), Class F Isolation (ISS°C),
Manufacturing according to requested resonance frequency (134-189-210-h7),
Production with three or single phases
SHUNT REACTORS:
Receiving power in the plants are shows characteristic capacitive effect too nowadays.
Inductive load (shunt reactor) is needed for companzed. Another mandatory of using these
reactors is the aim of to destroy of capacitive effect of long transmission lines.
According to filter power Terminal clamp or busbar connection in output,
Design with three or single phases, Heat protection with thermo contact (120°C),
F class isolation (ISS °C), IP 00 Protection class, when these products fixed to the panel,
it heat spreads so this heat spread should absolutely minimized with air circulation.
EASYPAN DISTRIBUTION BOARDS:
Employed for the purposes of energy distribution, lighting application, control of the installation
and protection against over-current at the private-houses and industrial plants, comply with
IEC 60439-1 standards and CE norms, in two types as flush and surface-mounted. Panels,
produced as 12, 18, 24, 30 and 36-way, are available in different kinds as circuit breaker,
automatic fuse, leakage current, switched and directly connected.
ELECTRONIC BALLASTS:
Federal electronic ballasts provide energy saving up to 30% and increase the economic life
of your light bulbs up to 50%, in comparison to conventional ballasts. The ballasts, those
are not effected from voltage changes, keeps the light flow stable continuously and decrease
the load of your compensation panel. Requiring no capacitors and starter, since the ballasts
are light-weighted, they facilitate the mounting to the armatures. Since they warm up less
in comparison to conventional ballasts, they place lower loads to air-conditioning system.
CAM SWITCHES:
They are produced according to IEC60947-3 TS EN 60947-3. In each segment having a
contact, covered by two, three or four units of silver, Federal Package Switches are employed
in different control transactions by increasing the segment numbers. On-off switches, change
over switches, motor revearsing switches, voltmeter switches, ammeter switches, star delta
starters, power switches, with lock (yellow-red handle) are being produced.
FEDERAL ELECTRIC
Investment & Trade Co.
1. Organize Sanayi Bölgesi 1. Yol No: 25 Hanl / SAKARYA
tel: +90 264 291 45 00 (pbx) fax: +90 264 275 41 81
All Over the World federal@federal.com.tr www.federal.com.tr