Professional Documents
Culture Documents
TEM
D
E
CONTENTS
SERVICE INFORMATION ............................ 3 Power Supply Circuit Inspection ..............................35 F
Satellite Radio Tuner Power and Ground Supply
PRECAUTIONS ................................................... 3 Circuit Inspection .....................................................37
Precaution for Supplemental Restraint System Satellite Radio Tuner Communication Circuit In- G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- spection ...................................................................37
SIONER" ................................................................... 3 Satellite Radio Tuner Left Channel Audio Signal
Circuit Inspection .....................................................39
PREPARATION ................................................... 4 H
Satellite Radio Tuner Right Channel Audio Signal
Commercial Service Tool .......................................... 4 Circuit Inspection .....................................................40
AUDIO ................................................................. 5 Steering Switch Check (With Bluetooth) ..................40
Steering Switch Check (Without Bluetooth) .............42 I
Component Parts Location ........................................ 5
Sound Is Not Heard from Front Door Speaker or
System Description ................................................... 6
Front Tweeter (Base and Mid System) ....................43
Schematic ................................................................. 8
Sound Is Not Heard from Rear Speaker (Base and J
Wiring Diagram - AUDIO - ....................................... 10
Mid System) .............................................................44
Audio Unit (Base System) Harness Connector
Sound Is Not Heard from Front Door Speaker or
Terminal Layout ...................................................... 21
Front Tweeter (Premium System) ...........................46
Terminal and Reference Value for Audio Unit AV
Sound Is Not Heard from Rear Speaker Assembly
(Base System) ......................................................... 21
(Premium System) ...................................................48
Audio Unit (Mid System) Harness Connector Ter-
Removal and Installation .........................................51
minal Layout ............................................................ 22 L
Terminal and Reference Value for Audio Unit (Mid AUDIO ANTENNA ............................................. 56
System) ................................................................... 22 Location of Antenna .................................................56
Audio Unit (Premium System) Harness Connector Removal and Installation of Roof Antenna ..............56
Terminal Layout ...................................................... 24 M
Terminal and Reference Value for Audio Unit TELEPHONE ..................................................... 58
(Premium System) .................................................. 25 Component Parts and Harness Connector Loca-
Audio Amplifier Harness Connector Terminal Lay- tion ...........................................................................58 N
out (Premium System) ............................................ 27 System Description ..................................................58
Terminal and Reference Value for Audio Amplifier Wiring Diagram - H/PHON - ....................................62
(Premium System) .................................................. 28 Bluetooth Control Unit Harness Connector Termi- O
Satellite Radio Tuner Harness Connector Termi- nal Layout ................................................................64
nal Layout ................................................................ 30 Terminal and Reference Value for Bluetooth Con-
Terminal and Reference Value for Satellite Radio trol Unit ....................................................................64
Tuner ....................................................................... 30 P
Bluetooth Control Unit Self-Diagnosis Function ......66
Audio Unit Self-Diagnosis Function (Base Sys- How to Proceed with Trouble Diagnosis ..................66
tem) ......................................................................... 31 Malfunction Code/Symptom Chart ...........................67
Audio Unit Self-Diagnosis Function (Mid and Pre- Power Supply and Ground Circuit Inspection for
mium System) ......................................................... 33 Bluetooth Control Unit .............................................67
Trouble Diagnosis ................................................... 33 Steering Wheel Audio Control Switch Does Not
Noise Inspection ...................................................... 35 Operate ....................................................................68
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
AV
PBIC0191E
AV
LKIA0853E
1. Front tweeter LH M46 (mid and pre- 2. Steering wheel audio control switch- 3. Front tweeter RH M47 (mid and pre-
mium system) es (MR20DE models with mid and mium system)
premium system)
4. Audio unit M43, M45, M53, M79 5. Display unit (mid and premium sys- 6. Front door speaker
tem) LH D10
RH D108
7. Rear speaker LH B27 (base and mid 8. Rear speaker RH B39 (base and mid 9. Satellite radio tuner B56, B60 (with
system) system) satellite radio tuner)
Rear speaker assembly LH B40 Rear speaker assembly RH B38
(premium system) (premium system)
10. Bluetooth control unit B15 (with 11. Audio amplifier B43, B44 (premium
Bluetooth) system)
AV
MID SYSTEM
AWKWA0087GB
AV
AWKWA0088GB
P
BASE SYSTEM
AWKWA0089GB
AV
AWKWA0090GB
P
BKWA0760E
AV
WKWA5899E
BKWA0762E
AV
AWKWA0091GB
P
WKWA5869E
AV
BKWA0765E
AWKWA0092GB
AV
WKWA5901E
AWKWA0093GB
WKIA5439E
D
Terminal and Reference Value for Audio Unit (Base System) INFOID:0000000001852138
E
Terminal
Signal Condition
(Wire color) Reference value
Item input/
Ignition (Approx.) F
+ – output Operation
switch
SKIB3609E
SKIB3609E AV
7 (GR) Ground ACC power supply Input ACC – Battery voltage
SKIB3609E
N
O
13 (L) 14 (Y) Audio signal rear RH Output ON Receive audio signal
P
SKIB3609E
WKIA5756E
Terminal and Reference Value for Audio Unit (Mid System) INFOID:0000000001852140
Terminal
Signal Condition
(Wire color) Reference value Example of symp-
Item input/
Ignition (Approx.) tom
+ – output Operation
switch
SKIA0177E
Audio sound
Receive audio No sound from
4 (G) 5 (V) signal rear Output ON
signal rear speaker LH.
LH
SKIA0177E
Press Phone/
0V
End switch
Press SEEK UP
1.7V Steering wheel au-
Remote switch
6 (P) Ground Input ON dio controls do not
control A Press VOL UP
3.3V function
switch
Except for
5.0V
above
Ignition switch System does not
7 (GR) Ground ACC signal Input ON Battery voltage
ACC or ON work properly.
SKIA0177E
Audio sound
Receive audio No sound from C
13 (L) 14 (Y) signal rear Output ON
signal rear speaker RH.
RH
SKIA0177E D
Remote Steering wheel au-
15 (LG) – control Input – – – dio controls do not
ground function E
Press Phone/
0V
Send switch
Press SEEK F
1.7V Steering wheel au-
Remote DOWN switch
16 (L) Ground Input ON dio controls do not
control B Press VOL
3.3V function
DOWN switch G
Except for
5.0V
above
19 (Y) Ground
Battery pow-
Input – – Battery voltage
System does not H
er work properly.
31 (P) – CAN-L – – – – –
32 (L) – CAN-H – – – – – I
Audio left
channel J
No sound from sat-
sound signal Receive audio
34 (R) 33 (G) Input ON ellite radio tuner
from satel- signal
left channel.
lite radio
tuner AV
SKIA0177E
L
Audio right
channel
No sound from sat-
sound signal Receive audio
36 (B) 35 (W) Input ON ellite radio tuner
from satel- signal M
right channel.
lite radio
tuner
SKIA0177E
N
Shield
37 – ground (au- – – – 0V –
dio signal)
Shield O
38 – ground (da- – – – 0V –
ta)
Satellite ra- P
Satellite radio tun-
dio tuner re- Turn audio unit
40 (L) Ground Input ON 5V er does not oper-
quest to ON
ate properly.
audio unit
SKIA4403E
SKIA4402E
WKIA5756E
Terminal
Signal Condition
(Wire color) Reference value Example of symp-
Item input/ B
Ignition (Approx.) tom
+ – output Operation
switch
Audio amplifier C
Amp. ON/
1 (G) Ground Output ON – More than 6.5V does not work
OFF signal
properly.
SKIA0177E
F
H
SKIA0177E
Press Phone/
0V
End switch
I
Press SEEK UP
1.7V Steering wheel au-
Remote switch
6 (P) Ground Input ON dio controls do not
control A Press VOL UP
3.3V function J
switch
Except for
5.0V
above
AV
Ignition switch System does not
7 (GR) Ground ACC signal Input ON Battery voltage
ACC or ON work properly.
SKIA0177E
N
P
SKIA0177E
Audio left
channel
No sound from sat-
sound signal Receive audio
34 (R) 33 (G) Input ON ellite radio tuner
from satel- signal
left channel.
lite radio
tuner
SKIA0177E
Audio right
channel
No sound from sat-
sound signal Receive audio
36 (B) 35 (W) Input ON ellite radio tuner
from satel- signal
right channel.
lite radio
tuner
SKIA0177E
Shield
37 – ground (au- – – – 0V –
dio signal)
Shield
38 – ground (da- – – – 0V –
ta)
Satellite ra-
Satellite radio tun-
dio tuner re- Turn audio unit
40 (L) Ground Input ON 5V er does not oper-
quest to ON
ate properly.
audio unit
SKIA4403E
SKIA4402E D
45 – LED ground Input ON Audio ON 0V
LED power
46 Ground
line
Output ON Audio ON 9V E
47 – LED ground Input ON Audio ON 0V
48 Ground Serial output Output ON Audio ON –
F
49 Ground Reset Output ON Audio ON 5V
50 Ground Shift clock Input ON Audio ON – Display unit will not
work.
51 Ground Serial input Input ON Audio ON – G
Command
52 Ground Input ON Audio ON –
data
Command H
53 Ground Input ON Audio ON –
data
Display
54 Ground Output ON Audio ON 5V
power line I
Display unit
55 – Input ON Audio ON/OFF 0V
ground
Display unit J
56 – Input ON Audio ON/OFF 0V
ground
WKIA5763E
N
Terminal
Signal Condition
(wire color) Reference value Example of
Item input/
Ignition (Approx.) symptom
+ – output Operation
switch
System does not
1 (R) Ground Battery Input – – Battery voltage
work properly.
SKIA0177E
SKIA0177E
SKIA0177E
SKIA0177E
SKIA0177E
SKIA0177E D
E
No sound from
Front door Receive audio
15 (L/W) 31 (L/R) Output ON front door speaker
speaker LH signal
LH.
F
SKIA0177E
No sound from
Front door Receive audio
16 (W/B) 32 (G/W) Output ON front door speaker
speaker RH signal
RH.
H
SKIA0177E
I
System does not
17 (G) Ground Battery Input – – Battery voltage
work properly.
20 (B) Ground Ground – ON – – –
J
No sound from
AV
Audio sound Receive audio front door speaker
21 (R) 5 (W) Input ON
signal front RH signal RH or front tweeter
RH.
L
SKIA0177E
M
No sound from
Audio sound Receive audio front door speaker
22 (W) 6 (B) Input ON
signal front LH signal LH or front tweeter
LH. N
SKIA0177E
SKIA0177E
SKIA0177E
LKIA0735E
Terminal
Signal Condition
(Wire color) Voltage
Item input/
Ignition (Approx.)
+ – output Operation
switch
SKIB3609E
SKIB3609E
SKIB3825E D
E
Communication signal Set to the satellite radio
29 (W/R) Ground Output ON
(SAT-AUDIO) mode
F
SKIB3824E
SKIB3826E
I
32 (Y) Battery power supply OFF
Ground − Battery voltage
36 (V) ACC power supply Input ACC
37 – Antenna signal – – – J
WKIA5764E
WKIA5765E
VERSION CHECK
1. Press the "AUDIO/CLOCK" switch to enter version diagnostics.
"S/W VER" (audio software version) is displayed.
WKIA5766E
WKIA5767E
WKIA5768E
WKIA5765E
D
BUTTON CHECK DIAGNOSTICS
When all segments are illuminated, a tone will sound while pressing
each individual switch.
E
G
WKIA5765E
The majority of the audio troubles are the result of outside causes (bad CD, electromagnetic interference,
etc.). Check the inspection items below to diagnose the malfunction.
J
MALFUNCTION WITH RADIO AND CD (BASE AND MID SYSTEM)
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera- H
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one. I
1.CHECK FUSE
P
Check that the following fuses of the audio amplifier (premium system) and audio unit are not blown.
Terminal No.
Unit (+) OFF ACC ON
(-)
Connector Terminal
Battery Battery Battery
19 Ground
voltage voltage voltage
Audio unit M43
Battery Battery
7 Ground 0V
voltage voltage
OK or NG
WKIA5769E
OK >> With premium system, GO TO 3.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
3.AUDIO AMPLIFIER (PREMIUM SYSTEM) POWER SUPPLY CIRCUIT CHECK
1. Disconnect audio amplifier connector.
2. Check voltage between audio amplifier and ground.
Terminal No.
Unit (+) OFF ACC ON
(-)
Connector Terminal
OK or NG
OK >> GO TO 4. WKIA3722E
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
4.GROUND CIRCUIT CHECK
Check continuity between audio amplifier harness connector B44
terminals 4, 20 and ground.
A
1.CHECK FUSES
Check that the following fuses are not blown.
B
Terminal No.
Unit (+) OFF ACC ON G
(-)
Connector Terminal
Battery Battery Battery H
32 Ground
Satellite voltage voltage voltage
B56
radio tuner Battery Battery
36 Ground 0V
voltage voltage
I
OK or NG
WKIA4539E
OK >> GO TO 3.
NG >> • Check connector housings for disconnected or loose J
terminals.
• Repair harness or connector.
3.GROUND CIRCUIT CHECK AV
Inspect satellite radio tuner case ground.
OK or NG
OK >> Inspection End. L
NG >> Repair satellite radio tuner case ground.
Satellite Radio Tuner Communication Circuit Inspection INFOID:0000000001852153
M
1.CHECK HARNESS - 1
1. Turn ignition switch OFF. N
2. Disconnect satellite radio tuner connector B56 and audio unit connector M45.
3. Check continuity between satellite radio tuner harness connec-
tor B56 (A) terminal 28 and audio unit harness connector M45
(B) terminal 40. O
OK >> GO TO 2.
NG >> Repair harness or connector.
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK HARNESS - 3
1. Check continuity between satellite radio tuner harness connec-
tor B56 (A) terminal 30 and audio unit harness connector M45
(B) terminal 42.
OK >> GO TO 4.
NG >> Repair harness or connector.
4.CHECK REQ1 SIGNAL
1. Connect satellite radio tuner connector and audio unit connector.
2. Turn ignition switch to ACC.
3. Check signal between satellite radio tuner harness connector
B56 terminal 28 and ground with CONSULT-III or oscilloscope.
1.CHECK HARNESS
1. Turn ignition switch OFF. F
2. Disconnect satellite radio tuner connector B56 (A) and audio unit connector M45 (B).
3. Check continuity between satellite radio tuner and audio unit.
G
Terminals
Satellite radio tuner Audio unit Continuity
Connector Terminal Connector Terminal H
21 33
A: B56 B: M45 Yes
22 34
I
4. Check continuity between satellite radio tuner and ground.
Terminals
WKIA5773E J
Satellite radio tuner Continuity
—
Connector Terminal
21 AV
A: B56 Ground No
22
OK or NG
L
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK LEFT CHANNEL AUDIO SIGNAL M
1. Connect satellite radio tuner and audio unit.
2. Turn ignition switch ON.
3. Check signal between satellite radio tuner connector B56 termi- N
nals 21 and 22 with CONSULT-III or oscilloscope.
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner connector B56 (A) and audio unit connector M45 (B).
3. Check continuity between satellite radio tuner and audio unit.
Terminals
Satellite radio tuner Audio unit Continuity
Connector Terminal Connector Terminal
23 35
A: B56 B: M45 Yes
24 36
4. Check continuity between satellite radio tuner and ground.
Terminals
WKIA5774E
Satellite radio tuner Continuity
—
Connector Terminal
23
A: B56 Ground No
24
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RIGHT CHANNEL AUDIO SIGNAL
1. Connect satellite radio tuner and audio unit.
2. Turn ignition switch ON.
3. Check signal between satellite radio tuner connector B56 termi-
nals 23 and 24 with CONSULT-III or oscilloscope.
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect Bluetooth control unit connector B15 and spiral cable connector M30.
3. Check continuity between Bluetooth control unit connector B15 (A) terminals 12, 13, and 14 and spiral
cable connector M30 (B) terminals 25, 31, and 33.
Terminals A
A B Continuity
Connector Terminal Connector Terminal
12 33
B
Terminals D
(+) Continuity
(–)
Connector Terminal
E
12
B15
13 Ground No
14 F
OK or NG
OK >> GO TO 2.
NG >> Repair harness. G
2.CHECK HARNESS
1. Disconnect audio unit connector M43. H
2. Check continuity between audio unit connector M43 (A) terminals 6, 15, and 16 and Bluetooth control unit
connector B15 (B) terminals 17, 19, and 18.
Terminals
I
(A) (B) Continuity
Connector Terminal Connector Terminal J
6 17
M43 15 B15 19 Yes
16 18 AV
OK or NG
OK >> GO TO 3. WKIA5776E
L
NG >> Repair harness.
3.SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M78. M
2. Check continuity between spiral cable terminals.
Resistance
Terminal Signal name Condition (Ω)
(Approx.)
Seek (down) Depress Seek down switch. 165
17 19 Phone/Send Depress Phone/Send switch. 0
Volume (down) Depress volume down switch. 487
Seek (up) Depress Seek up switch. 165
15 19 Phone/End Depress Phone/End switch. 0
WKIA5778E
Volume (up) Depress volume up switch. 487
OK or NG
OK >> Inspection End.
NG >> Replace steering switch. Refer to AV-51, "Removal and Installation".
Steering Switch Check (Without Bluetooth) INFOID:0000000001852157
Terminals
A B Continuity
Connector Terminal Connector Terminal
6 33
M43 15 M30 25 Yes
16 31
WKIA5807E
4. Check continuity between audio unit and ground.
Terminals
A Continuity
(–)
Connector Terminal
6
M43 15 Ground No
16
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
3.SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M78.
OK or NG
OK >> GO TO 4. C
NG >> Replace spiral cable. Refer to SRS-32, "Removal and
Installation".
WKIA5777E
1.HARNESS CHECK
1. Disconnect audio unit connector and front door speaker and front tweeter (mid system) connector (LH or AV
RH).
2. Check continuity between audio unit harness connector terminal
and front door speaker and front tweeter (mid system) harness L
connector terminal.
Terminals M
Audio unit Speaker or tweeter Continuity
Connector Terminal Connector Terminal
2 + N
B: M46*
3 -
11 +
B: M47* O
12 -
A: M43 Yes
2 +
B: D10
3 - P
11 +
B: D108
12 -
*: With mid system
3. Check continuity between audio unit harness connector terminal
and ground.
WKIA5351E
Terminals
Audio unit Continuity
—
Connector Terminal
2
3
A: M43 Ground No
11
12
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.FRONT SPEAKER SIGNAL CHECK
1. Connect audio unit connector, front door speaker connector and front tweeter (mid system) connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit connector terminals with
CONSULT-III or oscilloscope.
Terminals
(+) (-) Condi- Reference
tion signal
Con- Termi- Con- Termi-
nector nal nector nal
2 3
Receive
M43 M43 audio
11 12 signal
SKIA0177E
OK or NG
OK >> Replace front speaker. Refer to AV-51, "Removal and
Installation".
NG >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
WKIA5853E
Sound Is Not Heard from Rear Speaker (Base and Mid System) INFOID:0000000001852159
1.HARNESS CHECK
1. Disconnect audio unit connector and rear speaker connector.
Terminals
Audio unit Speaker Continuity B
Connector Terminal Connector Terminal
4 +
B: B27 C
5 -
A: M43 Yes
13 +
B: B39
14 - D
3. Check continuity between audio unit harness connector terminal
and ground.
E
Terminals
Audio unit Continuity
— F
Connector Terminal
4
5 G
A: M43 Ground No WKIA5353E
13
14
H
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
I
• Repair harness or connector.
2.REAR SPEAKER SIGNAL CHECK
1. Connect audio unit connector and rear speaker connector. J
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit harness connector termi- AV
nals with CONSULT-III or oscilloscope.
Terminals L
(+) (-)
Condi- Reference
Con- Con- tion signal
Termi- Termi-
nec- nec- M
nal nal
tor tor
4 5
N
Re-
ceive
M43 M43
13 14 audio
signal O
SKIA0177E
OK or NG P
OK >> Replace speaker. Refer to AV-51, "Removal and Instal-
lation".
NG >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
WKIA5808E
1.HARNESS CHECK
1. Turn ignition switch OFF.
2. Disconnect audio amplifier connector B43 and suspect speaker connector.
3. Check continuity between audio amplifier harness connector ter-
minal and suspect speaker harness connector terminal.
Terminals
Audio amplifier Speaker or tweeter Continuity
Connector Terminal Connector Terminal
15 +
D10
31 -
16 +
D108
32 -
B43 Yes
14 -
M46
30 +
13 -
M47
29 +
4. Check continuity between audio amplifier harness connector ter-
minal and ground.
Terminals
WKIA3372E
Audio amplifier Continuity
—
Connector Terminal
13
14
15
16
B43 Ground No
29
30
31
32
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.FRONT SPEAKER SIGNAL CHECK
1. Connect audio amplifier connector B43 and suspect speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
Terminals
(+) (-) Condi- Reference B
tion signal
Con- Termi- Con- Termi-
nector nal nector nal
13 29
C
14 30
Re- LKIA0602E
15 31 ceive D
B43 B43
audio
signal
16 32
SKIA0177E
E
OK or NG
OK >> Replace suspect speaker. Refer to AV-51, "Removal and Installation" or AV-51, "Removal and F
Installation".
NG >> GO TO 3.
3.HARNESS CHECK G
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M43 and audio amplifier connector B43.
3. Check continuity between audio unit harness connector termi- H
nals and audio amplifier harness connector terminals.
Terminals I
Audio unit Audio amplifier Continuity
Connector Terminal Connector Terminal
3 6 J
2 22
A: M43 B: B43 Yes
12 5
AV
11 21
4. Check continuity between audio unit harness connector termi-
nals and ground. L
Terminals
Audio unit Continuity M
—
Connector Terminal
3
N
2
A: M43 Ground No WKIA5814E
12
11 O
OK or NG
OK >> GO TO 4.
NG >> • Check connector housings for disconnected or loose terminals. P
• Repair harness or connector.
4.FRONT SPEAKER SIGNAL CHECK
1. Connect audio unit connector and audio amplifier connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
Terminals
(+) (-) Condi- Reference
tion signal
Con- Termi- Con- Termi-
nector nal nector nal
2 3
Receive
M43 M43 audio
11 12 signal
SKIA0177E
OK or NG
OK >> Replace audio amplifier. Refer to AV-51, "Removal and
Installation".
NG >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
WKIA5815E
Sound Is Not Heard from Rear Speaker Assembly (Premium System) INFOID:0000000001852161
1.HARNESS CHECK
1. Turn ignition switch OFF.
2. Disconnect audio amplifier connectors B43, B44 and suspect speaker connector.
3. Check continuity between audio amplifier harness connector ter-
minal and suspect speaker harness connector terminal.
Terminals
Audio amplifier Speaker Continuity
Connector Terminal Connector Terminal
11 4
C: B40
27 3
A: B43
12 4
C: B38
28 3
Yes
2 2
C: B40
18 1
B: B44
3 2
C: B38
19 1
4. Check continuity between audio amplifier harness connector ter-
minals and ground.
WKIA5816E
Terminals A
Audio amplifier Continuity
—
Connector Terminal
B
11
27
A: B43
12 C
28
Ground No
2
D
18
B: B44
3
19 E
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals. F
• Repair harness or connector.
2.REAR SPEAKER SIGNAL CHECK
G
1. Connect audio amplifier connectors B43, B44 and suspect speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio amplifier harness connector ter- H
minals with CONSULT-III or oscilloscope.
Terminals I
(+) (-)
Condi- Reference
Con- Con- tion signal
nec- Terminal nec- Terminal J
tor tor
A: 11 A: 27
B43 B43 AV
12 28
Re-
2 18 ceive
audio L
B: B:
signal
B44 3 B44 19
SKIA0177E
M
OK or NG
OK >> Replace suspect speaker. Refer to AV-51, "Removal
and Installation".
NG >> GO TO 3. N
WKIA5817E
3.HARNESS CHECK O
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M43 and audio amplifier connector B43.
P
Terminals
Audio unit Audio amplifier Continuity
Connector Terminal Connector Terminal
5 8
4 24
A: M43 B: B43 Yes
14 7
13 23
4. Check continuity between audio unit harness connector terminal
and ground.
Terminals
Audio unit Continuity
—
Connector Terminal
5
4
A: M43 Ground No WKIA5818E
14
13
OK or NG
OK >> GO TO 4.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
4.REAR SPEAKER SIGNAL CHECK
1. Connect audio unit connector M43 and audio amplifier connector B43.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit harness connector termi-
nals with CONSULT-III or oscilloscope.
Terminals
(+) (-) Condi- Reference
tion signal
Con- Con-
Terminal Terminal
nector nector
4 5
Re-
ceive
M43 M43
13 14 audio
signal
SKIA0177E
OK or NG
OK >> Replace audio amplifier. Refer to AV-51, "Removal and
Installation".
NG >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
WKIA5808E
A
AUDIO UNIT
J
LKIA0867E
Removal
1. Remove the cluster lid C. Refer to IP-10. L
2. Remove the display unit to audio unit harness.
3. Remove the cluster lid C bracket screws.
M
4. Remove the audio unit and display unit (if equipped).
Installation
Installation is in the reverse order of removal. N
FRONT SPEAKER
Removal
O
1. Remove the front pillar garnish. Refer to EI-31.
2. Remove the front speaker grille.
P
LKIA0855E
Installation
Installation is in the reverse order of removal.
FRONT DOOR SPEAKER
Removal
1. Remove the front door finisher. Refer to EI-28.
2. Remove the front door speaker screws (A), disconnect the front
door connector and remove the front door speaker (1).
LKIA0856E
Installation
Installation is in the reverse order of removal.
REAR SPEAKER
Removal
1. Remove the rear parcel shelf finisher. Refer to EI-35, "Removal and Installation".
2. Remove the rear speaker screws (A), disconnect the rear
speaker connector and remove the rear speaker (1).
LKIA0857E
Installation
Installation is in the reverse order of removal.
AUDIO AMPLIFIER
H
LKIA0865E
Removal
1. Slide the RH front seat toward the front to remove the audio amplifier rear bolts. J
2. Slide the RH front seat toward the rear to remove the audio amplifier front bolts.
3. Disconnect the audio amplifier connectors and remove the audio amplifier.
Installation AV
Installation is in the reverse order of removal.
SATELLITE RADIO TUNER L
LKIA0858E
Removal
1. Remove the luggage side finisher (LH). Refer to EI-41, "Removal and Installation".
2. Remove the satellite radio tuner bolts.
3. Disconnect the satellite radio tuner connector and remove the satellite radio tuner.
4. If necessary, remove the satellite radio tuner bracket bolts (A)
and remove the satellite radio tuner brackets (1).
LKIA0859E
Installation
Installation is in the reverse order of removal.
STEERING WHEEL AUDIO CONTROL SWITCHES
Removal
1. Remove the driver air bag module. Refer to SRS-30.
LKIA0860E
D
Installation
Installation is in the reverse order of removal.
AV
LKIA0862E
REMOVAL
1. Remove rear assist grip (LH). Refer to EI-38.
2. Remove three headliner rear clips. Pull down the rear part of the headliner to reposition out of the way.
CAUTION:
Use care when repositioning headliner to avoid causing damage.
LKIA0863E
D
INSTALLATION
Installation is in the reverse order of removal.
E
AV
WKIA5779E
1. Bluetooth control unit B15, B62 2. Steering wheel audio control 3. Microphone R4
switches
4. Bluetooth ON indicator R2 5. Combination meter M24 6. Audio unit M43, M53
BCM M18, M20 (view with instrument
7.
panel removed)
WKIA5780E
H
Bluetooth Control Unit
When the ignition switch is turned to ACC or ON, the Bluetooth con-
trol unit will power up. During power up, the Bluetooth control unit is I
initialized and performs various self checks. Initialization may take
up to 10 seconds. During this time the Bluetooth ON indicator will
flash until initialization is complete. If a phone is present in the vehi-
cle and paired with the Bluetooth control unit, Nissan Voice Recogni- J
tion will then become active and the Bluetooth ON indicator will
remain on. Bluetooth telephone functions can be turned off using the
Nissan Voice Recognition system. AV
WKIA5781E
BCM L
The BCM supplies power for the Bluetooth ON indicator (view with
instrument panel removed).
M
O
WKIA5782E
WKIA5784E
Bluetooth Microphone
The Bluetooth microphone is located in the roof console assembly.
The Bluetooth microphone sends a signal to the Bluetooth control
unit. The Bluetooth microphone can be actively tested during self-
diagnosis.
WKIA5785E
Bluetooth ON Indicator
The Bluetooth ON indicator is located in the roof console assembly.
The indicator will flash during power up while the Bluetooth control
unit is initializing. This process may take up to 10 seconds. If a
phone is present in the vehicle and paired with the Bluetooth control
unit, the indicator will remain on to indicate that the system is ready
for voice commands. The indicator flashes during self-diagnosis.
WKIA5786E
Audio Unit
WKIA5787E
AV
WKWA5870E
AV
WKWA5871E
WKIA5788E
Terminal
Signal Condition
(Wire color) Reference value
Item input/ Example of symptom
Ignition (Approx.)
+ – output Operation
switch
Battery pow- System does not
1 (Y) Ground Input – – Battery voltage
er work properly.
ACC/ System does not
2 (V) Ground ACC power Input – Battery voltage
ON work properly.
ON/ System does not
3 (W/L) Ground IGN power Input – Battery voltage
START work properly.
4 (B) – Ground – – – – –
6 – Shield – – – – –
PKIB5037J
Bluetooth con-
ACC/ Audio can not be
9 (G) 10 (L) Audio out Output trol unit sends
ON heard.
audio signal
SKIB3609E
N
When vehicle
Vehicle
speed is approx.
28 (G/Y) Ground speed signal Input ON –
40 km/h (25
(8–pulse) O
MPH)
PKIC0643E
Bluetooth P
Bluetooth Micro-
29 (B) Ground Microphone Output – – 5V
phone inoperative.
power
Bluetooth
33 – antenna sig- Input – – – –
nal
The Bluetooth control unit has two diagnostic checks. The first diagnostic check is performed automatically
every ignition cycle during control unit initialization. The second diagnostic check is performed by the techni-
cian using the steering wheel audio control switches prior to trouble diagnosis.
BLUETOOTH CONTROL UNIT INITIALIZATION CHECKS
• Internal control unit failure
• Bluetooth antenna connection open or shorted
• Steering wheel audio control switches (SEND/END) stuck closed
• Vehicle speed pulse count
• Bluetooth Microphone connection test (with playback to operator)
• Bluetooth inquiry check
SELF-DIAGNOSIS MODE
1. Turn ignition switch to ACC or ON.
2. Wait for the Bluetooth system to complete initialization and the Bluetooth ON indicator to stop flashing.
This may take up to 10 seconds.
3. Press and hold the steering wheel audio control switch SEND
button for at least 5 seconds. The Bluetooth system will begin to
play a verbal prompt.
WKIA5789E
Power Supply and Ground Circuit Inspection for Bluetooth Control Unit INFOID:0000000001852173
J
1.CHECK FUSES
Make sure the following fuses for the Bluetooth control unit are not blown. AV
Terminals
Ignition Switch Fuse No.
Connector Terminal L
1 All positions 22
B15 2 ACC/ON 6
3 ON/START 12 M
OK or NG
OK >> GO TO 2.
N
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3.
2.CHECK POWER SUPPLY CIRCUIT O
1. Disconnect Bluetooth control unit connector B15.
Battery
3 0V 0V
voltage
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between Bluetooth control unit and fuse.
3.CHECK GROUND CIRCUITS
1. Turn ignition switch OFF.
2. Check continuity between the following Bluetooth control unit
terminals and ground.
Terminals
Continuity
Connector Terminal —
4
B15 21 Ground Yes
22
OK or NG
WKIA5792E
OK >> Inspection End.
NG >> Repair or replace harness.
Steering Wheel Audio Control Switch Does Not Operate INFOID:0000000001852174
6 - Ground : Approx. 5V
16 - Ground : Approx. 5V
OK or NG
OK >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
NG >> GO TO 3.
WKIA5793E
17 - Ground : Approx. 5V
18 - Ground : Approx. 5V B
OK or NG
OK >> Repair or replace harness.
NG >> Replace Bluetooth control unit. AV-71, "Removal and C
Installation".
WKIA5794E
D
Voice Activated Control Function Does Not Operate INFOID:0000000001852175
NOTE:
Even under normal condition, Bluetooth voice guidance may not occur when pressing steering wheel audio E
control switch.
BLUETOOTH VOICE GUIDANCE IS HEARD WHEN PRESSING STEERING WHEEL AUDIO CON-
TROL SWITCH F
Terminals
Continuity
Connector Terminal Connector Terminal I
7 1
A: B15 8 B: R4 2 Yes
J
29 4
4. Check continuity between Bluetooth control unit harness con- WKIA5795E
nector B15 and ground. AV
Terminals
Continuity
Connector Terminal — L
7
A: B15 8 Ground No
M
29
OK or NG
OK >> GO TO 2. N
NG >> Repair harness or connector.
2.CHECK MICROPHONE POWER SUPPLY
1. Connect Bluetooth control unit connector and microphone connector. O
2. Turn ignition switch ON.
4 - Ground : Approx. 5V
OK or NG
OK >> GO TO 3.
NG >> Replace Bluetooth control unit. Refer to AV-71,
"Removal and Installation".
WKIA5796E
7 – 8:
PKIB5037J
LKIA0780E
OK or NG
OK >> Replace Bluetooth control unit. Refer to AV-71, "Removal and Installation".
NG >> Replace microphone. Refer to AV-71, "Removal and Installation".
BLUETOOTH VOICE GUIDANCE IS NOT HEARD WHEN PRESSING STEERING WHEEL AUDIO
CONTROL SWITCH
1.CHECK STEERING WHEEL AUDIO CONTROL SWITCH CIRCUIT
Refer to AV-68, "Steering Wheel Audio Control Switch Does Not Operate".
OK or NG
OK >> GO TO 2.
NG >> Replace applicable parts.
2.CHECK BLUETOOTH VOICE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect Bluetooth control unit connector and audio unit connector.
3. Check continuity between Bluetooth control unit harness con-
nector B15 (A) and audio unit harness connector M53 (B).
Terminals
Continuity
Connector Terminal Connector Terminal
9 26
A: B15 10 B: M53 28 Yes
11 30
4. Check continuity between Bluetooth control unit harness con- WKIA5797E
nector B15 (A) and ground.
Terminals A
Continuity
Connector Terminal —
9
B
A: B15 10 Ground No
11
OK or NG C
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK MUTE SIGNAL D
11 - Ground : Approx. 5V F
OK or NG
OK >> GO TO 4.
G
NG >> Replace audio unit. Refer to AV-51, "Removal and
Installation".
H
LKIA0782E
9 – 10: AV
SKIB3609E
WKIA5798E
L
OK or NG
OK >> Replace audio unit. Refer to AV-51, "Removal and Installation".
NG >> Replace Bluetooth control unit. Refer to AV-71, "Removal and Installation". M
N
COMPONENTS
ALNIA0977ZZ
Installation
Installation is in the reverse order of removal.
BLUETOOTH ANTENNA
Removal
NOTE:
Bluetooth antenna is mounted on top of the Bluetooth control unit.
1. Slide the LH front seat toward the rear.
2. Disconnect the Bluetooth antenna connector.
Installation
Installation is in the reverse order of removal.
D
AV
LKIA0861E
1. IPDM E/R E46, E48 2. Display unit 3. Audio unit M43, M53, M79
4. Steering wheel audio control switches 5. Combination switch M28 6. Combination meter M24
7. BCM M18, M20 (view with instrument panel 8. Bluetooth control unit B15 (with
removed) Bluetooth)
AV
WKWA5902E
AV
WKWA5872E
P
WKWA5903E
AV
BKWA0775E
P
BKWA0776E
AV
AWKWA0094GB
P
BKWA0778E
DESCRIPTION
• Diagnosis function consists of the self-diagnosis mode performed automatically.
• Self-diagnosis mode checks for connections between the units constituting this system, analyzes each indi-
vidual unit at the same time, and displays the results on the LCD screen.
DIAGNOSIS ITEM
OPERATION PROCEDURES D
1. Start the engine.
2. Turn the audio system off.
E
3. While pressing the “SCAN” button, turn the volume control dial
clockwise or counterclockwise for 30 clicks or more. When the
self-diagnosis mode is started a short beep will be heard.
F
G
WKIA5799E
H
4. When the self-diagnosis mode is started all of the display seg-
ments will be illuminated.
AV
LKIA0738E
VERSION CHECK
1. Press the "AUDIO" switch to enter version diagnostics. Press L
"AUDIO" switch again to display the "Software Ver:" (audio soft-
ware version).
M
LKIA0739E
O
LKIA0740E
3. Press "AUDIO" switch again to display the "CD Mech Ver:" (CD
mechanism version).
LKIA0741E
LKIA0742E
LKIA0743E
LKIA0744E
D
CAN CHECK DIAGNOSTICS
1. Press and hold the "AUDIO" switch for more than 1.5 seconds to
enter "CAN check diagnostics". Pressing the "AUDIO" switch
E
again will toggle through "ECM", "METER", and "BCM".
• If a current diagnostic result is detected "UN" will be displayed
under the heading PR (present)
• If no current diagnostic result is detected "OK" will be dis- F
played under the heading PR (present)
• If a past diagnostic result is detected 39 - 0 will be displayed
under the heading PA (past), indicating the number of key
G
cycles since that diagnostic result was detected
WKIA5800E
H
2. Pressing "AUDIO" again will display "Do You Want To Delete?" If
you do not wish to delete any diagnostic results, or no diagnostic
results exist, pressing "AUDIO" again will display "Key Failure 1
Not Found". After 6 seconds the display will return to the CAN I
check diagnostics screen.
AV
LKIA0746E
LKIA0747E
O
LKIA0748E
4. Press and hold the "SCAN" switch for more than 6 seconds to
delete the desired diagnostic item. "Failure Data Reset" will be
displayed, followed by a return to the "CAN check diagnostics"
screen.
LKIA0754E
DISPLAY UNIT
To replace the display unit. Refer to AV-51, "Removal and Installation".
AV