Professional Documents
Culture Documents
Annexure II Datasheet For - Passenger Lift
Annexure II Datasheet For - Passenger Lift
A LIFT
1 Make Sigma
2 Type ACRA (with machine room)
3 Model ACRA (with machine room)
4 Design ACRA (with machine room)
5 Capacity T 1600kg
6 Travel m Not decidted yet
7 Speed m/s 60m/s
8 Operation Simpex
9 No. of Working Floors incl. Ground Floor no. 3
10 No. of emergency Landings no. 3
11 Lift Pit well size mm x mm 1500mm
B CAR
1 Design Etched Pattern
2 Car Size mm x mm Standard per hoistway size (3050 x 2600)
3 Clear Height mm 2200mm (Car Height)
4 Car Gate Center Opening
5 Terminal switches
6 Final Limit Switches
Metallic Panel with push buttons for landing
7 selection, car position indicator, alarm bell and Possible to apply
emergency stop and bell for lift call
8 Lighting Arrangement Per different type of ceiling choices
9 Ventilation Arrangement Possible to apply
10 Material of wall panel STSHL Etching
11 Thickness of wall panel material mm 150mm (Open to change)
12 Material of car floor PVC or Decotile (Open to change)
13 Thickness of Chequered Plate mm
14 Three pin plug socket with switch on car roof
C CAR FRAME
1 Design Steel
2 Material of construction Steel
3 Factor of Safety
D LANDING DOORS
1 Number 3 (Per floor)
2 Type STSHL Etching
3 Material of construction STSHL
4 Hydraulic Door Closers for all Landing Doors yes / no
5 Dust Tight
6 Vision panel
7 Vision Panel - Fire Resistant Possible for fire resistant for 2 hours
8 Door Sills Possible to apply
9 Material of door sill
10 Interlock for door safety
11 Locking Devices for Landing Doors
E CAR SAFETY
Page 1 of 6
Annexure II
1 Design
2 Type
3 Safety Devices
4 Type of Safety Gear
5 Operation of Safety Gear
6 Material of safety Gear
7 Factor of safety
8 Material of Shaft
9 Diameter of Shaft mm
10 Guide Rails
11 Safety Gear Bearings
- Make
- Type
- Corrosion resistant
- Life of Bearings hrs
12 Overspeed Governor
13 Minimum tripping speed for over speed governor %
14 Material of Construction
15 Factor of safety
16 Interlock for power cut-off on activation of overspeed Governor
16 Material of Governor ropes
17 Factor of safety of governor ropes
18 Governor Bearings
- Make
- Type
- Self Lubricating
- Life of Bearings hrs
19 Traction & Deflector Sheave
- Design
- Diameter
- Material
- Machined Groove Yes/No
F LEVELLING ACCURACY
1 Minimum mm
2 Maximum mm
G TERMINAL BUFFERS
1 Design
2 Type
3 Location
4 Material of Springs, if applicable
5 Factor of safety
6 Stroke mm
H CONTROLLER
1 Design
2 Type
3 Temperature Control Yes/No
4 Interlock for Safety Yes/No
J LIFT MACHINE
1 Location
2 Make
3 Drive Motor
Page 2 of 6
Annexure II
- Make
- Type
- Power Kw
- Speed rpm
4 Brake
- Make
- Type
- Capacity to Hold the car at rest with 125% of rated load
5 Shaft
- Dia mm
- Material of construction
6 Pressurisation System for Lift machine room
K WIRE ROPES
1 Design
2 Make
3 Type
4 Factor of Safety
5 Number of Ropes
6 Diameter of Ropes mm
L MISCELLANEOUS
1 Lubrication System
2 Emergency Exit Possible
Common Base frame, Foundation bolts, holding
3 Possible
down bolts, washers, nuts and bolts etc.
4 Set of special tools and tackles for erection and maintenance
5 Commissioning Spares Possible
6 Spares for 2 Years of operation Possible
Page 3 of 6
Annexure II
Remarks
Page 4 of 6
Annexure II
Page 5 of 6
Annexure II
Page 6 of 6