Professional Documents
Culture Documents
CODE: 00ZMX2700/I1E
MX-2300/2700 G
MODEL MX-2300/2700 N
CONTENTS
CONFIGURATION
[1] MX-2300G/N, MX-2700G/N (Main unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] MX-DEX1/DEX2
(Stand/1x500 sheet paper drawer, Stand/2x500 sheet paper drawer) . . . . 2-1
[3] MX-TRX1 (Exit tray unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4] MX-RPX1 (Reversing single pass feeder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5] MX-LCX1 (Large capacity tray) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6] MX-FNX1 (Finisher) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[7] MX-PNX1A/B/C/D (Punch module (For Inner Finisher)) . . . . . . . . . . . . . . . . . 7-1
[8] MX-RBX1, MX-FNX2 (Paper pass unit, Saddle stitch finisher) . . . . . . . . . . . . 8-1
[9] AR-PN1A/B/C/D (Punch module (For Saddle stitch finisher)) . . . . . . . . . . . . 9-1
[10] MX-PBX1 (Printer expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
[11] MX-FRX1, MX-FRX1U (Data security kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[12] MX-PKX1 (PS3 expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
[13] AR-PF1 (Barcode font kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
[14] MX-NSX1 (Network scanner expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
[15] MX-AMX1 (Application integration module) . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1
[16] MX-AMX2 (Application communication module) . . . . . . . . . . . . . . . . . . . . . . 16-1
[17] MX-AMX3 (External account module) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1
[18] MX-RKX1 (Device tray with USB hub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-1
[19] MX-FXX1 (Facsimile expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-1
[20] MX-FWX1 (Internet Fax expansion kit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
[21] MX-SMX1 (256MB expansion memory board) . . . . . . . . . . . . . . . . . . . . . . . 21-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
1. Configuration
A. Lineup (Main unit and option)
2. Document cover
RSPF (MX-VRX1)
10. Punch module
● 2-hole (MX-PNX1A)
● 3-hole (MX-PNX1B)
● 4-hole (MX-PNX1C)
(MX-PNX1D)
HDD
HDD 6. Exit tray unit
7. Paper pass unit (MX-TRX1)
(MX-RBX1)
Copier/Printer (PCL) Copier/Printer (SPLC-c)
/Scanner model model
13. Staple cartridge
(Approx. 5000 x 3) (MX-2300N) (MX-2300G)
(AR-SC2) (MX-2700N) (MX-2700G)
(AR-PN1D)
14. Barcode font kit 17. Printer 18. Network 19. PS3 29. Facsimile expansion kit
expansion kit scanner expansion (MX-FXX1)
(PCL) expansion kit kit
CD ROM
CD CD CD ROM
(AR-PF1)
(MX-PBX1) (MX-NSX1)
FAX memory (8MB)
Data security kit (For MX-2300G/2700G) (MX-PKX1) (packed together)
(Including document control)
16. CC authentication 15. Commercial 20. Internet Fax 21. Sharpdesk 23. Sharpdesk
version version expansion kit 1 license kit 10 license kit
22. Sharpdesk 24. Sharpdesk
5 license kit 50 license kit
Security Security
ROM ROM
CD CD CD
(MX-USX1/ (MX-US10/
(MX-FWX1) USX5) US50)
For document For document
control PWB control PWB 26. Application 25. Sharpdesk 27. Application 28. External
integration 100 license kit communication account module
(MX-FRX1) (MX-FRX1U) module module
A. Bringing space
For installation of a large size machine, be sure to check that the
door size is great enough before bringing in.
B. Installing space
The following space must be provided around the machine in order E. Direct rays of the sun, dust, temperature,
to assure machine performances and proper operations.
humidity, gasses, chemicals, vibration
If any option is installed, provide the additional space for installing
it. (1) Temperature and humidity
Especially the space at the rear of the machine must be provided This machine is designed to perform properly under the specified
sufficiently. If not, the machine cannot exhibit functions against heat temperature and humidity. If the temperature and humidity exceeds
and dust, causing some troubles. the specified range, the machine may not operate properly and or
cause equipment failure.
30 cm Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
30 cm 45 cm
MX-2300G/N, MX-2700G/N 1 – 1
(2) Dust A. Implements, facility, and manpower
If dust enters the machine, it may cause dirty copy and a paper It is recommendable to use a forklift for bringing in the machine for
jam, resulting in a shortened lifetime. safety.
If no forklift is available, man-power of four persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
(3) Direct rays of the sun ronment.
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
3. Unpacking
A. Unpacking procedure
1) Remove the PP band.
2) Remove the top case.
3) Remove the internal packing pads with the machine.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
MX-2300G/N, MX-2700G/N 1 – 2
D. Check the parts packed together
1) Check that all the parts are in the package.
1 2 3
4. Installation
<Note before installation>
* When connecting the main unit with the optional one-tier paper
feed desk (MX-DEX1) or two-tier paper feed desk (MX-DEX2),
first unpack and install the one-tier paper feed desk (MX-DEX1)
or two-tier paper feed desk (MX-DEX2); then unpack the main
unit and securely place the main unit on the MX-DE1 or MX-
DEX2 (see 2-2) before installing the main unit.
A. Lock release
(1) Tray rotation plate lock release
1) Pull out the tray, and remove the rotation plate fixing material
and the tray note label.
MX-2300G/N, MX-2700G/N 1 – 3
(2) Scanner (2/3 mirror unit) lock release C. Primary transfer cleaning roller pressing/
1) Remove the optical unit fixing screw, and remove the note Transfer belt protect sheet removal
label. 1) Open the front cover.
2) Press the cleaning roller separation rod into the left hole in the
primary transfer cover with a screwdriver, and install it
B. Fusing heat roller pressing (F/R) securely.
1) Open the right door.
NOTE:
If the machine is left unused for one month or more, the heat
roller rubber may be deformed. In such a case, release the
pressure by pushing up both levers.
MX-2300G/N, MX-2700G/N 1 – 4
5) Remove the transfer belt protect sheet horizontally in the arrow 3) Pinch the knob and remove the development unit.
direction.
B A
2) Open the DV lock lever, and release the fixing screw. (1 posi-
tion for each color) B
MX-2300G/N, MX-2700G/N 1 – 5
6) Supply developer in the developer unit. 9) Shake the developer unit horizontally a few times.
* When replacing developer, use an extreme care not to drop
developer on the drive section (marked with {).
11) Fix it with the fixing screw. Insert the DV lock lever until it clicks
and close.
MX-2300G/N, MX-2700G/N 1 – 6
12) Close the drum positioning unit, and tighten the blue screw. 3) Turn ON the power switch on the operation panel.
ON
ON
13) Install the waste toner bottle unit (package part No. 1).
4) With the front cabinet open, enter the data for Simulation 25-2.
0
TEST SIMULATION NO.25-02 CLOSE
E. Set the control level for the reference toner AT DEVE ADJ_L_M : 128 AT DEVE VO_L_M : 128
0
TEST SIMULATION NO.25-02 CLOSE
MX-2300G/N, MX-2700G/N 1 – 7
7) Exit from Simulation mode by pressing the [CA] key on the * Be sure to install the color cartridges to their proper posi-
main unit. tions. Avoid installation to a different color position.
* Do not forcibly insert the toner cartridge.
Keep holding the cartridge and completely insert it.
* When the machine is transported with the developing unit
removed, be sure to remove the toner cartridge. (If not, tone
may be clogged.)
[Color toner cartridge positions]
Y M C BK
MX-2300G/N, MX-2700G/N 1 – 8
3) Detach the LSU cleaning bar from the front cover. H. Installation of the operation manual pocket
1) Install the Operation Manual storage (package part No. 3)
cover to the left side of the machine.
* If the MX-FNX2 (saddle finisher) is installed together with
installation of the machine, the Operation Manual storage
cover must be installed to the saddle finisher.
For details, refer to [8] MX-FNX2.
4) Insert the LSU cleaning rod, and slide it back and forth a few
times to clean the LSU dust-proof glass.
I. Tray setup
(1) Simulation setup
This is used to specify the paper type, paper size, and functions
used for each paper tray.
1) Press the [SYSTEM SETTINGS] key.
SYSTEM
SETTINGS
5) Replace the LSU claning bar to the front cover and attach the
waste toner bottle unit.
2) Touch the [Paper Tray Settings] key.
List Print
Total Count Default Settings (User)
System Settings
6) Close the front cabinet. Paper Tray Settings OK
Tray Settings
System Settings
Paper Tray Settings OK
Type / Size
1/6
Fixed Paper Side
Tray 1 Plain / A4
Disable Duplex
Doc.
Print Copy Fax I-Fax Filing Disable Staple
Disable Punch
(2) (1)
MX-2300G/N, MX-2700G/N 1 – 9
5) Touch the desired paper type. 2) Adjust the guide plates A and B by squeezing their lock levers
Example: Tray 1 is selected and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
System Settings
The guide plates A and B are slidable. Slide each guide plate
Cancel
while squeezing its lock lever.
Tray 1 Type/Size Setting
Select the paper type.
1/2
Plain Letter Head
Pre-Printed Pre-Punched
Recycled Colour
1/2
A
System Settings
Tray 1 Type/Size Setting Cancel
Select the paper type.
2/2
B
User Type 1 User Type 2 User Type 3 User Type 4
MX-2300G/N, MX-2700G/N 1 – 10
(3) Image loss, void area (see ADJ 17, ADJ 18) The print density must be changed gradually from the lighter level
• ADJ 17: Print area (Void area) adjustment (Print engine sec- to the darker level. The density changing direction must not be
tion) reversed. The density level of each color must be almost at the
same level.
1) Enter the simulation 50-10 mode.
2) Check the adjustment pattern to confirm that the items below b. When the PCL mode is not supported: (In the case of GDI
are in the range of the standard values. model)
Use SIM 67-25 to print the color balance adjustment sheet and
Content Standard adjustment value
compare each process (CMY) black patch color balance and the
X Lead edge void area 3.0 ± 1.0mm
black patch to check the color balance.
Y Rear edge void area 2.0 ± 1.0mm
Z1/Z2 FRONT/REAR void area 2.0 ± 2.0mm The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
If the above condition is not satisfied, or if it is set to a desired
reversed.
condition, execute the simulation 50-1.
The density level of each color must be almost at the same level.
• ADJ 18: Copy image position, image loss adjustment
Patch B may not be copied.
Document table mode
Patch A must not be copied.
1) Place a scale on the document table.
Check that the above items are normal. If not, make the adjust-
2) Enter the simulation 50-1 mode.
ment.
3) Perform the image lead edge reference position adjustment.
4) If the adjustment is required, adjust image lead edge reference L. Function and operation check
position by changing the setting value. Check that the following operations are normal.
5) Perform the image loss adjustment.
Check items Equipped condition
• Copy image position, image loss adjustment (RSPF mode) Key-in (operation panel)
(Refer to the MX-RPX1 SM.) Display (operation panel)
(4) Copy color balance, density (see ADJ 20) Paper feed Hand feed
operation Main unit paper
Before checking the coy color balance and density, be sure to exe-
tray
cute the following jobs.
Desk unit paper With the desk unit installed
* Execute the high density image correction (Process correction) feed tray
forcibly. (SIM 44-6) Paper size detection
* Execute the half-tone image correction forcibly. (SIM 44-26) Originals size Original table
(Method) detection mode
RSPF mode
Make a copy of the gray test chart (UKOG-0162FCZZ) and a copy
RSPF operation/ S-S mode
of the servicing color test chart (UK0G-0283FCZZ), and check that
two sided copy D-S mode
they are proper.
S-D mode
a. Note for execution of the color balance and density check in D-D mode
the color copy mode Bookbinding operation With the finisher installed
Stapling operation With the finisher installed
To check the copy color balance and density, use the gray test
Grouping operation With the finisher installed
chart (UKOG-0162FCZZ) and the servicing color test chart (UK0G-
Sorting operation With the finisher installed
0283FCZZ). Set the copy density level to "3" in the Text/Printed
Photo mode (Manual), and make a copy. M. Setup and adjustment data recording
At that time, all the color balance adjustments in the user adjust- Print the various setup data and the adjustment data (list) with
ment mode must be set to the default (center). SIM22-6 and keep the data.
In addition, be sure to use the specified paper for color. • In case of a memory trouble, if the data are not kept, all the
adjustments must be made again.
b. Note for checking the monochrome copy mode density
• If the data are kept, the setup values and the adjustment values
To check the density, use the gray chart (UKOG-0162FCZZ). Set can be entered without adjustments, shortening the servicing
the copy density level to "Manual 3" in the Text/Printed Photo mode time.
(Manual).
In addition, all the color balance adjustments in the user adjustment N. Necessary works before moving the machine
mode must be set to the default (center). 1) If the following options are installed, remove all of them from
• Check with the gray test chart (UKOG-0162FCZZ) the machine.
In the copy density check with the gray test chart, check to insure • Saddle stitch finisher
the following conditions. • Large capacity tray
NOTE: For the color (gray) balance, use the servicing color test 2) Remove the following consumable parts from the machine.
chart (UKOG-0283FCZZ) to check. • Paper
(5) Printer color balance (see ADJ 21) • Toner cartridge
Before checking the copy color balance and the density, be sure to • Development cartridge
execute the following procedures in advance. 3) Lock the following sections.
* Execute the high density image correction (process correction) • Scanner (Optical section)
forcibly. (SIM 44-6) • Paper cassette lift plate
* Execute the half tone image correction forcibly. (SIM 44-26) NOTE: Since the hard disk drive is built in the machine, use care
not to exert vibrations or shocks to the machine when in
a. When the PCL mode is supported:
transit.
Execute SIM 64-5 to print the print test pattern.
Set each set value to the default and press [EXECUTE] key. The
print test pattern is printed.
MX-2300G/N, MX-2700G/N 1 – 11
[2] MX-DEX1/DEX2 C. Check the
Service packed items
Manual
1) Check that all the items are included in the package.
1. Unpacking
A. Removal of the desk unit
1 2 3
No. Names of bundles Quantity
1 Right adjuster 1
2 Fixing screws (M4 x 8) 4
3 Installation cautionary note 1
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
OFF
OFF
B. Removal of the fixing material and packing
parts
* If the connector is removed first, it may be pinched in the install-
ing procedures. Therefore, keep it packed when unpacking the
package, and unpack it when connecting the connector to the
machine. 2) Open the front cabinet.
1) Remove the fixing material and packing parts. Turn OFF the power switch in the front cabinet of the main unit.
OFF
3) Disconnect the power plug of the main unit from the power out-
let, and remove the earth cord.
* Place the main unit on the desk unit slowly by fitting the
external lines. Check to insure that the positioning pin on the
top of the desk unit is securely engaged in the positioning
groove of the main unit.
2
2
3) Attach the removed fixing material to the position shown in the 3) Split the removed connector cover along the perforated line.
figure for storage.
Setting
Item Display Description Default
range
E CS3 Print off-center adjustment value 1 to 99 50
(tray 3)
F CS4 Print off-center adjustment value 1 to 99 50
(tray 4)
3) On the touch panel, press [↓] to select "E: 50 : CS3" or "F:
50 : CS4."
4) Enter the desired adjustment value through the numeric key-
pad.
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the rear.
2) Open the front cabinet. • Increasing the adjustment value by 1 causes the main scan/
Turn ON the power switch in the front cabinet of the main unit. print position to shift by 0.1 mm toward the front.
5) After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.
6) Check that the adjustment pattern image is printed in the cor-
rect position.
ON
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met:
+ 3.0mm
A-B = 0 -
3) Turn ON the power switch on the operation panel.
B
ON
No adjustment is needed if A - B = 0 ±3.0 mm.
If the above condition is not met, do the following:
7) Change the adjustment value.
ON (Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm.
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied.
8) After you have completed the adjustment, exit from Simulation
* For setting the tray size, refer to "Tray size setting" (1-9). mode by pressing the [CA] key.
G. Off-center adjustment
(1) Adjustment with the simulation
1) Run SIM50-10 using the keypad on the main unit.
The following screen appears:
0
TEST SIMULATION NO.50-10 CLOSE
A: 100 B : 50 ; MTF
C : 50 ; CS1
[64 - 140]
D : 50 ; CS2
EXECUTE OK
1. Unpacking
A. Removal of the exit tray unit
OFF
3) Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
1 2 3
No. Packed part names Quantity
1 Exit roller unit 1
2 Full detection actuator 1
3 Installation cautionary note 1 2
2. Installation 1
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
OFF
OFF
4) Connect the connector, and install the exit roller unit (package
part No. 1). Use the screw which was removed in step 3) and
fix the unit. 2) Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
ON
5) Install the connector cover, and fix it with the screw. 3) Turn ON the power switch on the operation panel.
ON
ON
6) Install the exit tray unit (A) and the full detection actuator (B)
(package part No. 2).
* Be careful of the installing direction of the full detection actu- D. Tray setting
ator. Use SIM26-1 to set the tray YES/NO.
B
B
OFF
OFF
OFF
1 2 3
3) Disconnect the power plug of the main unit from the power out-
let, and remove the earth cord.
4 5
3 C
2 A
B
D 6) Raise the RSPF unit upright, and fix it with the accessory
screw (M5 x 16) (package part No. 4).
3) Cut the screw hole in the cabinet, and install the SPF step 2
screw R (a) (package part No. 3) and the step screw R (b)
(package part No. 2). 2
1
b a b
2
a
1
7) Remove the connector cover. Connect the interface connector.
Check to insure that the projection (A) of the interface connec-
tor is in the groove on the main unit side as shown in the fig-
ure.
Tighten the connector fixing screw.
4) Insert the SPF step screw R and the step screw R into the
screw hole in the hinge section of the RSPF unit. Slide the unit A
toward the front side and close.
2
3
2
1
20mm
A4/Letter size
Is No Is No The height on
there a resist- there a resist- the right side
ance? ance? is not proper.
Yes Yes
A
Is
there a re- No
sistance?
a
Yes
Adjust hinge E
until there is a
resistance in
section B.
(Clockwise)
Adjust hinge E
until the E
separation in
section C is
deleted.
(Counter-
clockwise)
e) Check section C.
Check to confirm that the projection in section C in the right
Check section C. front side of then RSPF bottom is in contact with the glass
surface (b).
C
b
a
TEST CHART
A3 size
2) Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
b
ON
4) Raise the RSPF unit upright, and loosen the fixing screw of the
hinge.
ON
2
2
1
EXECUTE
1/1
0
TEST SIMULATION NO.50-28 CLOSE
AUTO IMAGE POSITION ADJUSTMENT:SERVICE
SIDE1 SIDE2
ALL
1. Unpacking
A. Removal of the large capacity tray unit
NOTE:
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
C. Check the packed items
1) Check that all the items are included in the package.
2 5 6
No. Names of bundles Quantity
1 Mounting plate upper 2
2 Connection unit 1
3 Fixing screw A (Hexagon with seat, S-tight, M4 x 35) 4
4 Fixing screw B (Hexagon with seat, S-tight, M4 x 12) 2
5 Fixing screw C (screw 4 x 8 cup) 1
6 Installation cautionary note 1
2) Remove the fixing material and the packing parts.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
OFF
OFF
OFF
1
2
1
3
2
8) Fix the other fixing screw B (package part No. 4), and tighten
the temporarily fixed screw B securely.
NOTE:
If the screw is loosened or removed when servicing, be sure
to execute "C. Height adjustment of the large capacity tray
unit" after completion of servicing.
2) Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
F side R side
A4 LT
At that time, set the mark position (▲) of the auxiliary guide
2) Adjust the mark position of the tray and the side plates in the and the cassette R to the same scale of the mark position ( )
lower section of the side plates F/R according to the desired of the side plate R and the size guide adjustment plate con-
size. Also adjust the upper section according to the desired firmed in procedure 1). (If the scale of the size guide adjust-
size, and fix with the four fixing screws (blue screws). ment plate is at the center, set it to the center. If the size guide
adjustment plate is in 1mm in the front side, set it in 1mm in the
front side.)
F side R side
2) Tighten the removed rear edge shaft with the fixing screw
(blue), and store it in the storage space inside the front cabi-
net.
At that time, check to insure that the stopper pawl is engaged 3) Pull out the tray again until it stops.
with the stopper reception of the large capacity tray unit.
4) Slowly insert the tray to the original position. a. Side plate size switch
1) Remove four fixing screws (blue screws) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.
F side R side
2) Insert the removed rear edge shaft into the mounting hole in
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
NOTE:
When the rear edge shaft is switched to B5, check to confirm
that the side plates F/R are already set to B5. If the side plates
F/R are not set to B5, the rear edge shaft cannot be switched
to B5.
ON A
+ 3.0mm
A-B = 0 -
B
3) Turn ON the power switch on the operation panel.
No adjustment is needed if A - B = 0 ± 3.0 mm.
If the above condition is not met, do the following:
7) Change the adjustment value.
ON (Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm.
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
ON isfied.
8) After you have completed the adjustment, exit from simulation
mode by pressing the [CA] key.
(2) Mechanical adjustment
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
G. Size setting removed, perform the following adjustment procedures.
Execute SIM 26-2 "Size setting" with the key operations of the main 1) Slowly pull out the tray until it stops.
unit.
1) The size selection menu of the large capacity tray is displayed
on the operation message display.
2) Select a size button to be set on the message screen.
H. Off-center adjustment
(1) Adjustment with the simulation
1) Run SIM 50-10 using the keypad on the main unit.
The following screen appears.
0
TEST SIMULATION NO.50-10 CLOSE
EXECUTE OK
R side
R side
F side
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2) Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
1 2 3
4 5 6 7
8 9 10 11 12 13
OFF
OFF
1
3) Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
10) Check to insure that the slide roller is in the rail groove, and
insert the inner finisher.
6) Engage the projection on the main unit frame with the hole in
the finisher fixing plate (package part No. 1).
7) Fix the right cover plate with the fixing screw (package part No.
8).
11) Fix the rear slide rail with the fixing screw (package part No. 8).
* Fix the side plate of the paper exit shifter with the fixing
guide.
13) Install the front open/close cover (package part No. 4) to the
front rail stay rotating shaft, and fix it with the resin clip (pack-
age part No. 9).
2) Remove the screw, and remove the connector cover.
2
14) Fix the punch cover (package part No. 5) together with the
3) Connect the finisher connector with the main unit connector,
band (metal fixture) with the fixing screw (package part No. 8).
and tighten with a screw.
1
ON
CAUTION Cleaning of the document scan section
When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
ON
ON
1 2
2. Installation
* When the punch unit is installed together with installation of
the MX-FNX1 (inner finisher), first install the inner finisher,
and then install the punch unit.
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
* Do not install the punch unit first because doing so would cause
interference between the inner finisher slide rail and the punch
unit drawer connector (possibly resulting in failure) when you
attempt to install the inner finisher.
OFF
OFF
OFF
3) Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
6) Remove the screw, and remove the band and the punch cover.
12) Fix the punch cover and the band together with one screw.
8) Fix the punch unit with a screw.
* When installing the punch unit, be careful not to bump it 1
against the drawer connector.
* Fit the positioning pin and insert it.
9) Make positioning with the dove (A) and fix the punch unit with
the screw which was fixing the dummy punch unit.
14) Install the front cabinet upper part using the two screws
removed in step 5).
15) Insert the finisher slide stopper between the slide rail and the
accuride, and fix it with the coin screw.
No clearance ON
First label Second label
Corner R end fitting
ON
[For RSPF] (package part No. 2)
ON
1 2 3
4 5 6 7 8 9
OFF
OFF
OFF
4) Remove the paper exit full detection actuator (A), and install
2 the reverse detection actuator (B) (package part No. 7).
* Be careful of the installing direction of the reverse detection
actuator.
1
1
A 2
A
B B
5) Engage the projection of the main unit frame with the hole in
C. Installation of the interface pass unit the right cover plate (package part No. 1), and install the right
1) Open the front cabinet. Remove the screws, and remove the cover plate and fix it with the fixing screw A (package part No.
front cabinet upper. 4).
* Be sure to clamp and fix the paper exit tray shifter side plate
with the fixing guide.
10) Fix the stopper (package part No. 8) with the fixing screw B
(package part No. 5).
7) Insert the reverse tray (package part No. 3) along the groove in
the interface left cabinet and the top surface of the right cover
plate.
* When inserting the reverse tray, check to insure that the
switch guide of the reverse tray is up.
11) Insert the interface pass unit along the guide rail.
8) Fix the reverse tray with the ornamental screw (package part
12) Fix the interface pass disconnection preventing lever with the
No. 6).
fixing screw A (package part No. 4).
1 2 3
4 5 6 7
8 9 10 11 12
Staple unit
3) Insert the staple cartridge (package part No. 4) into the staple
section until it clicks.
B. Connection of the main unit and saddle
finisher
1) Fix the connection plate (package part No. 2) to the paper feed
desk with two fixing screws A (package part No. 5).
NOTE:
Check to confirm that there are no clearance at the left and
right sections of the staple cartridge.
2) Install the rail bracket to the frame with four fixing screws B 4) Insert the staple unit and close the front cover of the finisher.
(package part No. 6).
2
Pawl
Screw B 1
(2) When the guide pin is fit with the connection hole
Pawl
in the finisher:
1) Insert the finisher into the main unit. Check to insure that the
upper and lower clearances between the main unit and the fin-
isher are even.
Clearance
Positioning dowel
Connection hole
Clearance
2) If the upper and lower clearances between the main unit and
the finisher are not even, remove the screw (one for each) of
the foot covers on the front/rear sides, and remove the foot
cover.
Guide pin
4) When the clearances are even, tighten the fixing screw of the
adjustment section, and install the foot cover.
Corner R end fitting
F. Connector connection
[For RSPF] (package part No. 9)
1) Connect the finisher connector with the connector of the inter-
face pass unit, and tighten the screw.
B 2
A
ON
ON
ON
OFF
OFF
1 2
3 4 5 6
3) Remove the earth cord and disconnect the power plug of the
No. Packed part names Quantity main unit from the power outlet.
1 Harness A (Purple) 1
2 Harness B (Orange) 1
3 Fixing screw (M4 x 6 with tooth lock washer) 1
4 Dust box label 1
5 Punch position label (For scanner) * 1
6 Punch position label (For RSPF) * 1
* The punch position labels (No.5 and No.6) and must be those
bundled with the MX-FNX2 rather than those bundled with the
AR-PN1A/B/C/D.
4) Disconnect the connector between the main unit and the sad-
dle finisher.
B
A
5) Remove the screws. Open the top door and remove the right
cabinet upper and the right cabinet middle.
7) Install the paper entry paper guide exclusively used for the
MX-FNX2 packed with the saddle finisher.
3) Remove two screws which are fixing the paper entry paper
guide.
4) Remove the hook (boss) on the upper side of the paper entry
paper guide.
Boss
Fixing
screw
Punch unit
Fixing screw
Fixing screw
(M4 x 6 with
tooth lock washer)
Harness B (Orange)
Harness A (Purple)
Clamp
Harness B (Orange)
CN14 on the PWB connected
Clamp
Harness A (Purple)
CN12 on the PWB connected
12) Open the top door, and install the right cabinet upper and fix it
with the screws.
Fixing screw Upper cover Fixing screw 15) Install the knob and close the front cover.
D. Punch position label attachment E. Turn on the power of the main unit
1) Attach the label to the position indicated in the figure. 1) Connect the connector.
[For scanner] (package part No. 5)
No clearance
First label Second label
Corner R end fitting
2) Connect the earth cord, and insert the power plug of the main
Document scan section unit into the power outlet.
ON
LED2 LED1
1
4) Turn ON the power switch on the operation panel.
PSW2 PSW1
ON ON
1 2 3 4 5 6 7 8
ON
3) After completion of the mechanical initializing, press DSW1 to
perform the automatic adjustment of the dust full sensor. After
completion of the adjustment, the LED2 lights up.
LED2
4) Set all the DIP switches to OFF, and check to confirm that the
LED2 turns OFF.
LED2
2
ON
1
1 2 3 4 5 6 7 8
5) Install the finisher rear cover, and fix it with the screw.
PROG
2 3
1
4 5 2) Remove the screw from the right rear cabinet.
3) Remove the right rear cabinet.
No. Packed part names Quantity 4) Remove the two screws from the control PWB unit.
1 DOCC PWB 1 • If the fax box unit is installed, carry out steps 5), 6), and
2 PROG ROM 1 7) additionally.
3 BOOT ROM 1 5) Pull out the control PWB unit and remove the snap band.
4 Operation manual 1
6) Remove the interface cable from the frame.
5 Installation manual 1
7) Remove the connector.
2. Installation 8) Pull out and remove the control PWB unit.
PROG ROM
G
PRO
2) After checking that the operation panel has gone out, open the
BOOT ROM
front cabinet and turn the main power switch to the "OFF" posi-
tion.
3) Remove the power plug of the main unit from the outlet.
3) Loosen the four lower screws that secure the rear cabinet.
4) Remove the seven screws indicated in the illustration.
5) Remove the rear cabinet.
4) Ensure that pins 1 and 2 of the DIP switch on the DOCC PWB
are OFF.
0
TEST SIMULATION NO.55-01 CLOSE
DATA 12345678
12345678
EXECUTE
0
TEST SIMULATION NO.55-01 CLOSE
DATA 00000000
12345678
EXECUTE
0
TEST SIMULATION NO.55-01 CLOSE
DATA 00000000
12345678
EXECUTE
Small Great
00000000 00000111
12345678 12345678
1. Unpacking
A. Parts included
1 2 3
2. Installation
<Note before installation>
NOTE: To enable PS3, the product key must be acquired. (For
details of the acquiring method of the product key, refer to
the distributor.)
Write down the acquired product key on the product key
sheet and pass it to the user.
B. PS3 check
1) Print the test page in PS3 fonts by the key operation of the
operation panel. (Select the PS font list by the procedures
described in the data list print printer test page of the system
setup guide.)
Check to confirm that printing is made normally.
APPLICATION
NUMBER
MACHINE
SERIAL
NUMBER
PRODUCT
KEY
BOOT
PROGRAM
1 2 3 PCL/BUMON
BARCODE
No. Packed part names Quantity FAX IMG EXT
1 CD-ROM 1 PS KANJI
2 Operation Manual 1
3 Installation cautionary note 1
5) Install the MFP PWB shield plate upper and connect the con-
nector.
2. Installation
A. Installation of the barcode font ROM PWB
1) Turn OFF the main switch of the copier, and disconnect the
power plug of the copier from the power outlet.
2) Remove the screw, and remove the rear cabinet.
1
2
3) Remove the connector and the screw, and remove the MFP 2
PWB shield plate upper.
7) Insert the power plug of the copier into the power outlet. Turn
ON the power switch and perform the following procedures.
2
B. PCL expansion font list check
1) PCL expansion font list check
Select the PCL expansion font list by the procedures described
in the printer test page in the system setup guide.
Check to confirm that the barcode font list is printed.
1. Unpacking
A. Parts included
1 2 3
No. Packed part names Quantity
1 CD-ROM 2
2 Product key sheet 1
3 Installation guide 1
2. Installation
<Note before installation>
• To enable the network scanner function, the product key must be
acquired.
1. Unpacking
A. Parts included
1 2 3
No. Packed part names Quantity
1 CD-ROM 2
2 MX-AMX1 GETTING STARTED GUIDE 1
3 Sharpdesk license kit Operation Manual 1
2. Installation
<Note before installation>
• To enable the Application Integration Module function, the prod-
uct key must be acquired.
• The network scanner expansion kit must be installed in advance.
The installing procedure differs depending on the destination.
To install the network scanner expansion kit, refer to the descrip-
tions for the "[14] Network scanner expansion kit (MX-NSX1)" in
this Service Manual.
MACHINE SERIAL
OSA
NUMBER
File Retrieve
File
Folder
Quick File
Folder PRODUCT KEY
App 01
1/2
App 02
App 03
App 04
OSA Settings OK
1. Unpacking
A. Check the packed items
OFF
1 2 3
3) Disconnect the power plug of the main unit from the power out-
4 5 6 let, and remove the earth cord.
Used in other models
7 8 9
No. Packed part names Quantity
1 Keyboard rack 1
2 Mounting fixture 1
3 USB cable 1
4 AC cord 1
5 Installation cautionary note 1
6 Screw A 6
7 Clamp 4
8 Step screw A 2
9 Step screw B 2 B. Installation of the USB-hub base
1) Install the clamp. Connect the USB cable to the connector, and
2. Installation engage the cable with the groove through the clamp.
OFF
2) Install the mounting fixture and the keyboard rack, and fix them
with the screws A. Install the clamps.
OFF
B B
4) Attach two step screws A to the two positions where the fixing
screws have been removed.
A
B
5) Engage the USB-hub base with the step screw A on the left
side. Then slide the base to the rear side.
6) Engage the USB-hub base with the step screw A on the right
side, and push it down.
ON
ON
ON
3) Insert the step screw into the mounting hole of the fax box unit.
4) Use a screw that has been removed in step 1) to secure the
fax box unit.
2. Installation
<Note before installation>
• Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
A. Turn off the power switches of the main unit. C. Pull out the control PWB.
1) Turn the power switch located on the operation panel to the 1) Push the location indicated in the illustration to unlock, and
“OFF” position. remove the ozone filter cover from the right rear cabinet.
2) Remove the screw from the right rear cabinet and remove the
2) After checking that the operation panel has gone out, open the
right rear cabinet.
front cabinet and turn the main power switch to the “OFF” opsi-
tion.
3) Remove the power plug of the main unit from the outlet.
3) Fit the interface cable into the opening that has been cut.
E. Attach the interface cable. 4) Attach the right rear cabinet cover to the main unit.
1) Connect the interface cable to the control PWB unit. At this time, check that the four hooks are properly fitted to the
[Note] Check that the connector is not obliquely inserted. main unit.
2) Push the interface cable into the recessed portion of the sheet 5) Secure the right rear cabinet with the screw.
metal on the control PWB unit.
3) Attach the snap band to the sheet metal of the control PWB
unit.
1. Unpacking
A. Parts included
1 2
No. Packed part names Quantity
1 CD-ROM 1
2 Product key sheet 1
2. Installation
<Note before installation>
• In order to enable the Internet Fax send function, the product key
must be acquired.
• In order to specify the address of the Internet Fax with the PC-
FAX driver, the PC-FAX driver must be updated by the Internet
Fax expansion kit.
2. Installation
A. Installation of the expansion memory
1) Turn OFF the main switch of the copier, and disconnect the
power plug of the copier from the power outlet.
2) Remove the screw, and remove the rear cabinet.
3) Remove the connector and the screw, and remove the MFP
PWB shield plate upper.
<2> Push the sections indicated with → at the same time with
both hands until the right and the left buttons are locked.
3
1
5) Install the MFP PWB shield plate upper, and connect the con-
nector.
4) Install the expansion memory to the connector.
1
2
7) Insert the power plug of the copier into the power outlet. Turn
ON the power switch.
Example:
Trademark acknowledgements
Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
Windows® XP, Windows® 2000 Server, Windows® Server 2003 and Internet
Explorer® are trademarks or copyrights of Microsoft Corporation in the U.S.A. and
other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
re
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186, Japan
2005 November Printed in Japan