Professional Documents
Culture Documents
BGPROPAK60 R2
AQUAVAR
30-60 HZ KITS
Goulds Water Technology
Residential Water Systems
FEATURES
Simple, fast sizing and installation.
Range curves and selection charts generated from actual R&D tests.
Kits configured for 30 Hz minimum and 60 Hz maximum operation.
Controller Must Be Set For 60 Hertz Operation.
Kits use matched water end and motor (see component chart).
Wiring is as easy as standard three-wire control box:
• L1, L2 and Ground in from power supply
• Red, Yellow, Black and Ground out to motor
60 PSI Factory Preset Pressure - easily adjusted to higher pressures.
KITS INCLUDE:
• CentriPro Three Phase Motor 1.5 – 5 HP, 230 V
• CentriPro Aquavar SOLO2 Controller with Transducer
• Goulds Water Technology GS Water End (pump)
PAGE 2
Goulds Water Technology
Residential Water Systems
PAGE 3
Goulds Water Technology
Residential Water Systems
SELECTION CHART
Pump Depth to Water in Feet/Ratings in GPM (Gallons Per Minute)
HP PSI
Model 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300
0 33.0 31.8 30.4 29.0 27.4 25.7 22.6 21.5 19.3 15.4
25GS20 2 50 30.5 29.4 28.0 26.0 24.1 22.1 20.0 17.2 13.2
60 30.4 29.0 27.4 25.7 22.6 21.5 19.3 15.4 12.2
Shut-off PSI 139 130 121 113 104 95 87 78 69 61 52 43 35 26 17
FEET
25 GPM
2 HP
30 – 60 Hz
300
TOTAL DYNAMIC HEAD
200
100
0
0 5 10 15 20 25 30 35 40
CAPACITY – GPM
PAGE 16
Goulds Water Technology
Residential Water Systems
SELECTION CHART
Pump Depth to Water in Feet/Ratings in GPM (Gallons Per Minute)
HP PSI
Model 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 340 380 420
0 33.0 32.2 31.5 30.5 29.6 28.3 27.1 25.8 22.6 19.0 14.0
25GS30 3 50 32.3 31.6 30.8 29.8 28.5 27.3 26.0 24.5 23.0 21.2 19.5 17.4 11.5
60 33.0 32.2 31.5 30.5 29.6 28.3 27.1 25.8 24.1 22.6 20.9 19.0 16.9 14.0 10.0
Shut-off PSI 191 183 174 165 157 148 139 131 122 113 105 96 87 79 70 53 35 18
FEET
500
25 GPM
3 HP
30 – 60 Hz
400
TOTAL DYNAMIC HEAD
300
200
100
0
0 5 10 15 20 25 30 35 40
CAPACITY – GPM
PAGE 17
Goulds Water Technology
Residential Water Systems
SELECTION CHART
Pump Depth to Water in Feet/Ratings in GPM (Gallons Per Minute)
HP PSI
Model 140 160 180 200 220 240 260 280 300 340 380 420 460 500 540 580 620 660 700 740
0 33.0 32.5 31.5 30.2 29.0 27.6 26.0 24.2 22.4 20.5 18.3 15.8 12.0
25GS50 5 50 32.6 32.1 31.6 31.0 30.3 29.9 29.2 27.8 26.3 24.5 22.6 21.8 18.7 16.0 12.7
60 33.0 32.5 32.0 31.5 30.8 30.2 29.8 29.0 28.3 26.9 25.1 23.3 21.5 19.5 17.0 14.0 9.5
Shut-off PSI 286 277 268 260 251 242 234 225 216 199 182 165 147 130 113 95 78 61 43 26
FEET
1000
25 GPM
5 HP
30 – 60 HP
800
TOTAL DYNAMIC HEAD
600
400
200
0
0 5 10 15 20 25 30 35
CAPACITY – GPM
PAGE 18
Goulds Water Technology
Residential Water Systems
Controller to Motor
Controller Motor Copper Wire Size 75ºC Insulation Exposed to a Maximum of 50ºC (122ºF) Ambient Temperature ⑥
Output HP 14 12 10 8 6 4 2 1/0 2/0 3/0 4/0 250 300
¾ 690 1100 1748 2523 3978 6316 9945
1 558 890 1413 2040 3216 5106 8041
230V
1½ 445 709 1126 1625 2562 4068 6406
3 PH
2 324 516 820 1184 1866 2963 4666 7410 9351
3 241 384 609 880 1387 2202 3467 5506 6949 8750
5 * 235 373 539 849 1348 2123 3372 4255 5358 6755 7964 9520
⑤ Reduce lengths by 13% for 200 V systems. ⑥ Lengths in bold require 90ºC wire. Shading indicates 40º C maximum ambient. * Wire does not meet the N.E.C. ampac-
ity requirement.
The lengths in each of the Wire Sizing tables represent 100% of the allowable voltage drop when motor is running at full load. When sizing
wire, the voltage drop of each wire segment must be included. The total must not exceed 100% of the allowable drop. Take for example a 1.5
HP motor with a distance from Service Entrance to Controller of 100' and 500' between the Controller and Motor.
• Service Entrance to Controller = 100' of 10 AWG (100/455) = 22 % (455' is from the S.E. to Controller chart)
• Controller to Motor = 500' of 12 AWG (500/709) = 71 % (709' is from the Controller to Motor chart)
Total Drop (must be ≤ 100%) 93 %
If the distance from the Controller to Motor was 600' (600/709) = 85% + 22% = 107%, we would need to use #10 wire for that segment, ex.
600/1126 = 53% + 22% (for 100' of #10) = 75% which is acceptable. It is also acceptable to use different wire sizes for the Buried and Well
sections of wire.
PAGE 21
Goulds Water Technology
Residential Water Systems
Diaphragm Tank Sizing and Pre-Set Pressure Use Total Tank Volume, not drawdown volume, to
Recommendations: select the proper tank size. The total tank volume
Diaphragm type (captive air) tanks are required on should be approximately 20% of the pump’s
these systems. maximum flow. For example, when using a 10 gpm
pump the system requires a minimum 2 gallon (total
Table 1: Tank Sizing Selection volume) tank.
Maximum Recommended Tanks The tank sizing recommendations are field proven to
Pump GPM Total Volume Order No. or Order No. prevent objectionable pressure drops on start-up and
10 2 V6P TP6P
provide smooth operation for the majority of variable
23 4.5 V15P TP15P
speed pump systems.
41 8.2 V25P TP25P
70 13.9 V45 TP45 Set the tank pressure, while tank is empty of water, to
100 19.9 V60 TP60 20 psi below the desired system pressure setting. Ex.
for a 50 psi system pressure, charge the tank to 30 psi.
PAGE 22
Goulds Water Technology
Residential Water Systems
PAGE 23
PRESSURE RANGES FOR ALL AVAILABLE TRANSDUCERS
1AS15 / 3AS20 3AS30 3AS50
Transducer
Minimum PSI Maximum PSI Minimum PSI Maximum PSI Minimum PSI Maximum PSI
100 PSI ➀ 20 85 20 85 10 50
200 PSI ➁ 40 170 40 170 20 100
300 PSI 60 255 60 255 30 150
➀ Standard on 1AS15/3AS20, 3AS30 ➁ Standard on 3AS50
Warning! Exploding tank can injure or kill, some combinations of Transducer and Controller allow system pressure adjustment to exceed the maximum
working pressure of the tank and piping.
Ensure system pressure is set below the maximum working pressure of the tank and system piping.
Protect tank and piping against overpressure, install a properly sized pressure relief valve (PRV) able to pass full pump flow at the maximum
working pressure of the tank. In finished basements or where PRV blow-off can cause property damage, pipe the PRV to a suitable drain.
9.9 5.3
.28 DIA. ½" KNOCKOUT
2.4
(TRANSDUCER)
1.2
2.7
.50 DIA. 5.3
½" x 1"
2X (.28 DIA.)
COMBINATION
KNOCKOUTS
3.3 BOTH SIDES
1.6 .28 DIA. 1.9
Xylem Inc.
2881 East Bayard Street Ext., Suite A
Seneca Falls, NY 13148
Phone: (866) 325-4210
Fax: (888) 322-5877
www.gouldswatertechnology.com
Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license.
CentriPro and Aquavar SOLO are trademarks of Xylem Inc. or one of its subsidiaries.
Noryl and Lexan is a registered trademark of GE Plastic.
© 2016 Xylem Inc. BGPROPAK60 R2 June 2016