Professional Documents
Culture Documents
PART NUMBERS:
A 1 L B
2 S
3 A
PRODUCT DESCRIPTION
“A” type glands are commonly referred to as “stuffing glands”. They provide a controlled, pull
resistant environmental displacement seal on the cable outer sheath, minimising damage to cables
that exhibit “cold flow” characteristics. The gland maintains IP66 & IP68 to 50 metres. Options are
available for use with LSOH cables and extreme temperature applications.
COMPLIANCE STANDARDS:
IEC 62444
EN 62444
EXAMPLE PART NUMBERING:
A2LB/NP/20/M20
CERTIFICATION:
Neoprene Seal (2) - Silicone Seal (3) - Neoprene/Lead (1) - Silicone/ ABS Specified ABS Rules
2
Lead (4)
CERTIFICATE NO.
L Peppers Standard Designation 20-LD1944057-PDA
OPTIONAL
ACCESSORIES:
B Aluminium (A) / Brass (B) / Stainless Steel (S)
LOCKNUT Brass (ACBLN) / St Steel (ACSLN) / Aluminium (ALALN)
C PVC Shroud (C) - PCP Shroud (P) - Silicone LSOH Shroud (3) EARTH TAG Brass (ACBET) / St Steel (ACSET) / Aluminium (ACAET)
K-V-H Locknut & Nylon (K), Fibre (V) or PTFE (H) IP Washer IP WASHERS Nylon (ACNSW) / Fibre (ACFSW) / PTFE (ACPSW)
12* M12 x 1.5 3/8” 16 0.9 6.0 33 19.0 21.0 0.038 L19
12* M16 x 1.5 3/8” or 1/2” 16 0.9 6.0 33 25.4 28.0 0.068 L24
12* M20 x 1.5 3/8” or 1/2” 16 0.9 6.0 33 25.4 28.0 0.082 L24
16 M16 x 1.5 3/8” or 1/2” 16 4.0 8.4 33 25.4 28.0 0.097 L24
16 M20 x 1.5 1/2” or 3/4” 16 4.0 8.4 33 25.4 28.0 0.104 L24**
20S M20 x 1.5 1/2” or 3/4” 16 7.2 11.7 33 25.4 28.0 0.102 L24**
20 M20 x 1.5 1/2” or 3/4” 16 9.4 14.0 33 30.0 33.0 0.127 L30
25 M25 x 1.5 3/4” or 1” 16 13.5 20.0 33 37.6 41.4 0.166 L38
32 M32 x 1.5 1” or 1 ¼” 16 19.5 26.3 33 46.0 50.6 0.244 L46
40 M40 x 1.5 1 ¼” or 1 ½” 16 23.0 32.2 37 55.0 60.5 0.396 L55
50S M50 x 1.5 1 ½” or 2” 16 28.1 38.2 37 65.0 71.5 0.558 L65
50 M50 x 1.5 2” 16 33.1 44.1 37 65.0 71.5 0.438 L65
63S M63 x 1.5 2” or 2 ½” 19 39.2 50.1 37 80.0 88.0 0.832 L80
63 M63 x 1.5 2 ½” 19 46.7 56.0 37 80.0 88.0 0.664 L80
75S M75 x 1.5 2 ½” or 3” 19 52.1 62.0 37 90.0 99.0 0.924 L90
75 M75 x 1.5 3” 19 58.0 68.0 37 90.0 99.0 0.714 L90
80 M80 x 2.0 3” or 3 ½” 25 62.2 72.0 50 104.0 115.2 1.514 L104
85 M85 x 2.0 3” or 3 ½” 25 69.0 78.0 50 104.0 115.2 1.332 L104
90 M90 x 2.0 3 ½” or 4” 25 74.0 84.0 50 114.0 125.7 1.622 L114
100 M100 x 2.0 3 ½” or 4” 25 82.0 90.0 50 114.0 125.7 1.523 L114
110 M110 x 2.0 - 25 87.0 102.0 88 135.0 148.0 2.550 N/A
120 M120 x 2.0 - 25 97.0 112.0 88 145.0 159.0 3.200 N/A
130 M130 x 2.0 - 25 107.0 122.0 88 155.0 170.0 4.750 N/A
Gland size does not necessarily equate to the entry thread size. When selecting IP Washer & Shroud material for use with glands, please be aware of the
NOTES
Dimensions (A) & (B) may differ for glands with non metric entry threads. Please refer to our accessories temperature range to ensure they are suitable for the intended installation.
“Thread Reference Tables” for specific dimensions. * Gland sizes 12 not available in aluminium.
Assembly instructions must be read prior to installation and adhered to in full. ** For gland sizes 16 and 20S when used with 3/4" NPT entry thread an L30 shroud would be
Peppers supply products with parallel entry threads that conform to the flameproof threaded joint required.
requirements of IEC/EN 60079-1 and other equivalent standards. We usually incorporate a thread
run out according to general machining techniques and parts will not have a full form thread for
the entire length. Peppers Cable Glands Limited will not be held responsible for clients’ installations
where this has not been taken into account.
Peppers Cable Glands Ltd: www.peppers.co.uk | Email: sales@peppers.co.uk | Tel: +44 (0) 1276 64232 73
Industrial Cable Gland
Size : 16mm to 90mm & ½" to 3½” Thread : Metric, NPT Size : 16mm to 90mm Thread : Metric, NPT
Standard : BS 6121: Part-1:2005, EN 50262: 1999, Operating Temp. : -20°C to +80°C Standard : BS 6121: Part-1:2005, EN 50262:1999, Operating Temp. : -20°C to +80°C
IEC62444:2010 Features : Outer Compression Seal
IEC62444:2010 Features : Compression Seal
Function : Providing environmental seal on outer Seal Material : Neoprene
Function : Providing seal on outer sheaths of all types of Cable Type : Unarmoured Cable sheaths of all types of unarmoured c a b l e
unarmoured cable in indoor and outdoor area. Seal Material : Neoprene Seal in indoor and outdoor area. Accessories : PVC Shroud, Earth Tag, Galvanized Steel
Ingress Protection : IP66 Lock Nut and Brass Washer
Accessories : PVC Shroud, Earth Tag, Thread Seal, Ingress Protection : IP66
Material : Brass CW614N, Stainless Steel 316L Cable Type : All types of screened flexible wire braid
Serrated Washer Material : Brass CW614N, Stainless Steel 316L (e.g. CY/SY) or wire braid armoured cable
123 124
ELECTRICAL SOLUTIONS
A.
System
Overview
E4.
Permanent
Identification
E5.
Lockout/
Tagout
& Safety
Solutions
F.
Index
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) D1.17
ELECTRICAL SOLUTIONS
A.
System
Overview
Part Number System for Metric Lugs
B1.
Cable Ties
B2.
Cable
Accessories
B3.
Stainless
Steel Ties
LCMA 150 – 10 – X
150 = 150mm2 10 = 10mm 1=1 X = 10 C = 100
5=5 L = 50 C1.
Wiring
Part Number System for Pan-Lug ™ Compression Metric Lugs Duct
B B
E2.
N Labels
M
INSPECTION
INSPECTION WINDOW E3.
WINDOW I Pre-Printed
I & Write-On
Markers
L
L
E4.
Copper Figure Dimensions Permanent
Conductor (mm) Identification
Size Current Stud Hole Panduit Std.
Part Class 2R Rating Size Die Index Pkg. E5.
Number (mm²) (Amps) (mm) ØI B M N L ØD No.‡ Qty. Lockout/
LCMA6-5-C* 4–6 30 M5 3.8 10.0 7.8 6.2 27.5 5.5 P10 100 Tagout
LCMA6-6-C* 4–6 30 M6 3.8 10.8 7.8 6.2 27.5 6.6 P10 100 & Safety
LCMA6-8-C* 4–6 30 M8 3.8 13.0 8.0 8.0 30.5 9.0 P10 100 Solutions
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) D2.107
ELECTRICAL SOLUTIONS
A.
System
Overview
Metric Conductor, One-Hole, Standard Barrel with
Window Lug (continued)
B1.
Cable Ties Figure Dimensions
Copper (mm)
Conductor Current Stud Hole Panduit Std.
Part Size Rating Size Die Index Pkg.
B2. Number Class 2R (mm²) (Amps) (mm) ØI B M N L ØD No.‡ Qty.
Cable LCMA10-5-C 10 — M5 4.5 11.0 9.8 6.0 30.8 5.5 P21 100
Accessories LCMA10-6-C 10 — M6 4.5 11.0 9.8 6.0 30.8 6.6 P21 100
LCMA10-8-C 10 — M8 4.5 13.0 8.5 8.0 30.8 9.0 P21 100
B3. LCMA10-10-C 10 — M10 4.4 14.5 8.5 8.0 30.8 11.0 P21 100
Stainless LCMA16-5-C* 16 65 M5 5.5 13.0 10.3 6.5 34.5 5.5 P24 100
Steel Ties LCMA16-6-C* 16 65 M6 5.5 13.0 10.3 6.5 34.5 6.6 P24 100
LCMA16-8-C* 16 65 M8 5.5 13.0 10.3 6.5 34.5 9.0 P24 100
LCMA16-10-C* 16 65 M10 5.5 15.0 10.2 8.0 36.7 11.0 P24 100
C1.
Wiring LCMA25-6-C 25 — M6 6.9 14.0 10.0 8.0 37.0 6.6 P29 100
Duct LCMA25-8-C 25 — M8 6.9 15.5 10.0 8.0 37.0 9.0 P29 100
LCMA25-10-C 25 — M10 6.9 15.5 10.0 8.0 37.0 11.0 P29 100
LCMA35-6-C 35 — M6 8.2 15.5 12.3 8.5 42.0 6.6 P29 100
C2. LCMA35-8-C 35 — M8 8.2 15.5 12.3 8.5 42.0 9.0 P29 100
Surface
Raceway LCMA35-10-C 35 — M10 8.2 15.5 12.3 8.5 42.0 11.0 P29 100
LCMA35-12-C 35 — M12 8.2 21.5 14.5 11.5 48.0 14.0 P29 100
LCMA50-6-L 50 — M6 9.8 18.0 11.5 10.0 46.5 6.6 P37 50
C3. LCMA50-8-L 50 — M8 9.8 18.0 11.5 10.0 46.5 9.0 P37 50
Abrasion LCMA50-10-L 50 — M10 9.8 18.0 11.5 10.0 46.5 11.0 P37 50
Protection
LCMA50-12-L 50 — M12 9.8 23.0 14.0 11.0 50.0 14.0 P37 50
LCMA70-6-L 70 — M6 11.5 20.8 14.5 11.5 53.5 6.6 P45 50
C4. LCMA70-8-L 70 — M8 11.5 20.8 14.5 11.5 53.5 9.0 P45 50
Cable LCMA70-10-L 70 — M10 11.5 20.8 14.5 11.5 53.5 11.0 P45 50
Management
LCMA70-12-L 70 — M12 11.5 20.8 14.5 11.5 53.5 14.0 P45 50
LCMA95-8-L 95 — M8 13.5 24.5 15.0 13.5 60.5 9.0 P54 50
LCMA95-10-L 95 — M10 13.5 24.5 15.0 13.5 60.5 11.0 P54 50
D1.
LCMA95-12-L 95 — M12 13.5 24.5 15.0 13.5 60.5 14.0 P54 50
Terminals
LCMA95-16-L 95 — M16 13.5 24.5 15.0 13.5 60.5 18.0 P54 50
LCMA120-8-L 120 — M8 15.2 27.5 15.5 14.5 65.0 9.0 P62 50
LCMA120-10-L 120 — M10 15.2 27.5 15.5 14.5 65.0 11.0 P62 50
D2.
Power LCMA120-12-L 120 — M12 15.2 27.5 15.5 14.5 65.0 14.0 P62 50
Connectors LCMA120-16-L 120 — M16 15.2 27.5 15.5 14.5 65.0 18.0 P62 50
LCMA150-8-X 150 — M8 16.5 30.5 18.0 16.5 70.5 9.0 P66 10
LCMA150-10-X 150 — M10 16.5 30.5 18.0 16.5 70.5 11.0 P66 10
D3.
LCMA150-12-X 150 — M12 16.5 30.5 18.0 16.5 70.5 14.0 P66 10
Grounding
Connectors LCMA150-16-X 150 — M16 16.5 30.5 18.0 16.5 70.5 18.0 P66 10
LCMA150-20-X 150 — M20 16.5 30.5 22.0 16.5 74.0 22.0 P66 10
LCMA185-10-X 185 — M10 18.6 33.5 16.5 17.5 72.5 11.0 P76 10
E1. LCMA185-12-X 185 — M12 18.6 33.5 16.5 17.5 72.5 14.0 P76 10
Labeling
LCMA185-16-X 185 — M16 18.6 33.5 16.5 17.5 72.5 18.0 P76 10
Systems
LCMA185-20-X 185 — M20 18.6 33.5 21.0 17.5 77.0 22.0 P76 10
LCMA240-10-X 240 — M10 20.8 37.5 21.0 19.5 86.5 11.0 P87 10
LCMA240-12-X 240 — M12 20.8 37.5 21.0 19.5 86.5 14.0 P87 10
E2.
Labels LCMA240-16-X 240 — M16 20.8 37.5 21.0 19.5 86,5 18.0 P87 10
LCMA240-20-X 240 — M20 20.8 37.5 21.0 19.5 86.5 22.0 P87 10
LCMA300-10-5 300 — M10 23.5 42.5 22.0 20.0 94.5 11.0 P94 5
E3. LCMA300-12-5 300 — M12 23.5 42.5 22.0 20.0 94.5 14.0 P94 5
Pre-Printed
LCMA300-16-5 300 — M16 23.5 42.5 22.0 20.0 94.5 18.0 P94 5
& Write-On
Markers LCMA300-20-5 300 — M20 23.5 42.5 22.0 20.0 94.5 22.0 P94 5
LCMA400-12-5 400 — M12 27.0 49.5 26,5 23.5 107.0 14.0 P106 5
E4. LCMA400-16-5 400 — M16 27.0 49.5 26.5 23.5 107.0 18.0 P106 5
Permanent LCMA400-20-5 400 — M20 27.0 49.5 26.5 23.5 107.0 22.0 P106 5
Identification LCMA500-12-1 500 — M12 31.0 57.5 28,5 25.5 120.0 14.0 P125 1
LCMA500-16-1 500 — M16 31.0 57.5 28.5 25.5 120.0 18.0 P125 1
E5. LCMA500-20-1 500 — M20 31.0 57.5 28.5 25.5 120.0 22.0 P125 1
Lockout/
Tagout LCMA500-00-1* 500 — Blank 31.0 57.5 — — 120.0 — P125 1
& Safety LCMA630-16-1 630 — M16 34.5 63.0 28.5 27.5 131.0 18.0 P125 1
Solutions LCMA630-20-1 630 — M20 34.5 63.0 28.5 27.5 131.0 22.0 P125 1
LCMA630-00-1* 630 — Blank 34.5 63.0 — — 131.0 — P125 1
F. ‡See page D3.83 for tool and die information.
Index *UL Recognized only.
**Consult cable manufacturer for voltage stress relief instructions with applications greater than 2000 V.
D2.108 Prime items appear in BOLD.
ELECTRICAL SOLUTIONS
A.
System
Overview
*Wire sizes #26 – 22 AWG, are not UL Listed or CSA Certified. E2.
**Bulk packaging may be available, contact Panduit Customer Service for additional information. Labels
‡UL and CSA approved tooling/product combinations. For crimping tool information, see pages D1.83, D1.84,
D1.86 and D1.88.
E3.
Pre-Printed
& Write-On
Markers
E4.
Permanent
Identification
E5.
Lockout/
Tagout
& Safety
Solutions
F.
Index
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) D1.9
ELECTRICAL SOLUTIONS
A.
System
Overview
D3.
Grounding
Connectors
E1.
Labeling
Systems
E2.
Labels
E3.
Pre-Printed
& Write-On
Markers
E4.
Permanent
Identification
E5.
Lockout/
Tagout
& Safety
Solutions
F.
Index
For technical assistance in the U.S., call 866-405-6654 (outside the U.S., see inside back cover for directory) D1.23
ELECTRICAL SOLUTIONS
A.
System
Overview Selection Guide – Specialty Terminals
B1.
Page
Material Style Feature Type Number
Cable Ties
Pin Terminal Insulation Support PV-P D1.54
Vinyl
Blade Terminal Insulation Support DV-M D1.55
B2.
Cable
Accessories Specialty
C4. 0.5-1.5 mm2 PV18-P47-CY 22 – 18 AWG Red 0.150 0.97 0.07 0.49 100 1000
Cable CT-100A,
Management PV14-P47-C 16 – 14 AWG Blue 0.170 0.97 0.07 0.49 CT-260, 100 1000
1.5-2.5 mm2 CT-1550,
CT-1551,
PV10-P55-LY* 12 – 10 AWG Yellow 0.250 1.10 0.10 0.55 CT-2500 50 500
D1. 4.0-6.0 mm2
Terminals
*Not UL Listed.
L **Bulk packaging may be available, contact Panduit Customer Service for additional information.
For crimping tool information, see pages D1.83, D1.84, and D1.88.
D2.
Power
Connectors
P W
D3.
Grounding Pin Terminal, Non-Insulated
Connectors
Type P-P
• Solid pin designed to prevent damage to the wire from over • Barrel of terminal internally beveled to provide quick and easy
E1.
Labeling tightening, resulting in a reliable electrical connection wire insertion
Systems • Brazed seam protects terminal barrel from splitting during the • For use with pin-type terminal blocks
crimp process • Maximum recommended operating temperature 302°F (150°C)
• Internal barrel serrations assure good wire contact and maximum • UL rated up to 600 V per UL 486A/B
E2. tensile strength
Labels
D1.54 Order number of pieces required, in multiples of Standard Package Quantity. Prime items appear in BOLD.
6/3/2020 0301 KSS Nylon Cable Tie
● Material: UL approved Nylon 66, 94V-2, with good tensile strength and insulation, not easy to get
aging.
● Color: Standard color is natural, black, other special colors are available upon request.
● Feature: Low Smoke and Halogen Free cable tie suitable for various industry, also household DIY
and gardening.
Max. operating temperature up to 85℃
● Application: One piece self-lock cable tie save the time and make effective for installation.
Miniature
※ CVT-070, 100 doesn't have minimum bundle diameter.
※ CV-200T tail
※ CV-300STZ, 180T, 190T tail Unit: mm
Item No. Min Loop
Length Max.
Width Tensile
Natural Black L Bundle
W Strength
Dia.
100 pcs / Bag 1000 pcs / Bag 100 pcs / Bag 1000 pcs / Bag mm inch lbs kgs
※ CVT-070 CVT-070K CVT-070B CVT-070KB 71.0 2 13/16" 1.60 11 7 3
※ CVT-100 CVT-100K CVT-100B CVT-100KB 103.0 4" 1.95 22 11 5
Intermediate
※ CVT-070, 100 doesn't have minimum bundle diameter.
※ CV-200T tail
※ CV-300STZ, 180T, 190T tail Unit: mm
Item No. Min Loop
Length Max.
Width Tensile
Natural Black L Bundle
W Strength
Dia.
100 pcs / Bag 1000 pcs / Bag 100 pcs / Bag 1000 pcs / Bag mm inch lbs kgs
CV-120 CV-120K CV-120B CV-120KB 120.0 4 3/4" 3.20 28
CV-140 CV-140K CV-140B CV-140KB 142.0 5 1/2" 3.20 34
CV-150 CV-150K CV-150B CV-150KB 150.0 6" 3.60 36
CV-180 CV-180K CV-180B CV-180KB 180.0 7" 3.60 46
※ CV-180T CV-180TK CV-180TB CV-180TKB 180.0 7" 3.60 46
Standard
※ CVT-070, 100 doesn't have minimum bundle diameter.
※ CV-200T tail
※ CV-300STZ, 180T, 190T tail Unit: mm
Item No. Min Loop
Length
Max. Tensile
Natural Black L Width
Bundle Strength
W
1000 pcs / Dia.
100 pcs / Bag 100 pcs / Bag 1000 pcs / Bag mm inch lbs kgs
Bag
CV- 50 22
CV-120L CV-120LK CV-120LB 120.0 4 3/4" 4.80 27
120LKB
CV- 160.0 6 1/4" 4.80 39
CV-160L CV-160LK CV-160LB
160LKB
CV-190 CV-190K CV-190B CV-190KB 190.0 7 1/2" 4.80 49
www.kss.com.tw/e4k/e4-3/E0301-1.asp? 2/4
6/3/2020 0301 KSS Nylon Cable Tie
Heavy Duty
※ CVT-070, 100 doesn't have minimum bundle diameter.
※ CV-200T tail
※ CV-300STZ, 180T, 190T tail Unit: mm
Item No. Min Loop
Length Max.
Width Tensile
Natural Black L Bundle
W Strength
Dia.
100 pcs / Bag 1000 pcs / Bag 100 pcs / Bag 1000 pcs / Bag mm inch lbs kgs
CV-380S CV-380SB 380.0 15" 6.40 108 100 45
CV- 120 55
CV-120LL CV-120LLK CV-120LLB 120.0 4 3/4" 7.60 22
120LLKB
CV-150L CV-150LK CV-150LB CV-150LKB 150.0 6" 7.60 32
www.kss.com.tw/e4k/e4-3/E0301-1.asp? 3/4
6/3/2020 0301 KSS Nylon Cable Tie
www.kss.com.tw/e4k/e4-3/E0301-1.asp? 4/4
Products for Surface Protective Materials Products for Harness
22 PO (Polyolefin) SPV®: Overview 23 Tape for Wire Harnesses Low-VOC PVC Tape/Flame-retardant, heat-resistant and High heat-resistant PVC Adhesive Tape
C Series C-300 0.060 1,250 200 - Comparison of Base Properties Comparison of the Characteristics of
Heat-resistance, flame-retardant and High heat-resistant PVC Adhesive Tapes
C-400 0.060 1,250 200 - -
PVC adhesive tape 25
C-500 0.060 1,250 200 - -
Flame-retardant tape also has a thin layer type of 0.070mm thickness Strength
C-600 0.090 1,250 200 - -
20 Flame Elongation
Offers each temperature zone of heat-resistant type retardancy
Strength (N/19mm)
V Series V-420 0.055 1,250 200 - -
Thickness Length
Product Product No. Color Applications
(mm) (m)
Surface Protective Materials General/bundling No. 2101TVH/No. 2101NVH Black 0.10 20 Low VOC emissions
General unity thin layer type,
Protection Film for Interior Parts SPV®-C-600 General/bundling No. 2117TVH/No. 2117NVH Black 0.070 35
Low VOC emission product
Black, Blue, Green, Yellow, White,
Low VOC emissions,
Color variation No. 2107TVH/No. 2107NVH Brown, Gray, Red, Orange, Pink, Light 0.13 20
Used for protection of automobile interior parts color identifi cation use
green, Sky blue, Purple, Transparent
SPV®-C-600 has been developed for protecting automobile interior parts, which are exposed to severe Flame-retardant No. 2100FRTV Black 0.11 25 Flame-retardant type
heat and UV radiation. This film can be perfectly applied to suit any specific location and surface size for Flame-retardant No. 2117FRTV Dark gray 0.070 35 Flame-retardant thin type
protection, as well as effectively prevents scratching and keeps the vehicles from getting dirty during the
No. 2237FRTV Orange, Gray 0.13 20 Heat-resistant, flame-retardant type
assembly process. Heat-resistant,
flame-retardant Fog-resistant, heat-resistant,
No. 2239FRTV Black 0.11 25
flame-retardant type
Features Applications No. 2207TVH 0.13 20 Heat-resistance temperature limit: 85°C
Can be used for interior parts with a wide choice of substrates; no adhesive residue General interior parts such as door trim, instrument panels and High heat Black
No. 2280TV 0.08 33 Heat-resistance temperature limit: 105°C
remains when peeled. door steps resistance (Please inquire for other colors)
No. 2290TV 0.11 33 Heat-resistance temperature limit: 125°C
Adheres well to rough surfaces.
Thicker No. 213JTV Black, Dark blue 0.30 10 Tube replacement use
Standard Size
21 22
Construction Solutions Indonesia
Aplikasi Produk
Dimensi
U Bolt
Hex Nut
Asdrat
Long Nut
C4.
Cable
Management
HILTI CP 670
Firestop Coated Board System
1 2 3 4 5
9LVLWWKH+LOWL)LUHVWRS'HVLJQ&HQWUH5HJLVWHUWRGD\DWZZZKLOWLFRXNFIV +LOWL2XWSHUIRUP2XWODVW
Hilti Firestop Systems Hilti Firestop Systems
1 2 3 4 5
9LVLWWKH+LOWL)LUHVWRS'HVLJQ&HQWUH5HJLVWHUWRGD\DWZZZKLOWLFRXNFIV +LOWL2XWSHUIRUP2XWODVW
Standard firestop detail
APPLICATION
Hilti CP 670 Firestop acoustic
board. Head of Wall application
Test Up to Approvals
Fire Integrity 120 minutes EN 1366-3
Insulation 120 minutes BS 476: Part 20
Air Tightness Head of Wall joint
Age Testing 30 years BS EN ISO 140-3
CP 606 at all
batt edges
Drywall partition
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
Hilti CP 670 Firestop acoustic
board - Type A Horizontal detail
Test Up to Approvals
Fire Integrity 60 Minutes BS476 pt 20
Insulation 60 Minutes EN 1366-3 Mixed services
Acoustics 39 dB passing through
Age Testing 30 Years Solid floor
600 mm
Any Length
CP 670 (Type A)
coated batt
CP 606 Intumescent mastic must be used at all batt edges in accordance with the installation guidelines.
The CP 643N collars should be secured to the underside of the batt using M8 threaded rod through the fixing hooks
and secured with oversized washers on the upper face of the batt. The CP 670 coated board should be installed
tightly around the service pipe.
All service items must be secured either side of the batt seal system.
1. The application limits on this detail are for guidance purposes only. For more detailed information on the full range of available test results please
contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS 476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's installation instructions, by competent, experienced installers using Hilti branded
products.
APPLICATION
Hilti CP 670 Firestop acoustic
board - Type B Horizontal detail
Test Up to Approvals
Fire Integrity 60 Minutes BS476 pt 20
Insulation 60 Minutes EN 1366-3 Mixed services
Acoustics 52 dB passing through
Age Testing 30 Years Solid floor
1200 mm
Any Length
CP 670 (Type B)
coated batt
CP 643N collar for PVC & PE pipes CP 648 pipewrap for PVC & PE pipes
between 20 mm - 160 mm dia. between 20 mm - 160 mm dia
CP 606 Intumescent mastic must be used at all batt edges in accordance with the installation guidelines. All joints to
be staggered
The CP 643N collars should be secured to the underside of the batt using M8 threaded rod through the fixing hooks
and secured with oversized washers on the upper face of the batt. The CP 670 coated board should be installed
tightly around the service pipe.
All service items must be secured either side of the batt seal system.
1. The application limits on this detail are for guidance purposes only. For more detailed information on the full range of available test results please
contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS 476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's installation instructions, by competent, experienced installers using Hilti branded
products.
APPLICATION
Hilti CP 670 Firestop acoustic
board - Type B Horizontal detail (2hr)
Test Up to Approvals
Fire Integrity 120 Minutes (90 minutes-CP 648) EN 1366-3
Insulation 120 Minutes (90 minutes -CP 648) Mixed services
Acoustics 52 dB passing through
Age Testing 30 Years Solid floor
1000 mm
2000 mm
150 mm CP 670 C
Coatback on each face of
cables/cable tray
CP 670C Coatback
CP 670 (Type B)
coated batt Alternative solution for
combustible pipes:
The CP 644 collars should be secured to the underside of the batt using M8 threaded rod through the fixing hooks
and secured with oversized washers on the upper face of the batt. The CP 670 coated board should be installed
tightly around the service pipe.
All service items must be secured either side of the batt seal system.
1. The application limits on this detail are for guidance purposes only. For more detailed information on the full range of available test results please
contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS 476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's installation instructions, by competent, experienced installers using Hilti branded
products.
APPLICATION
Hilti CP 670 Firestop acoustic
board - Face Fix detail
Test Up to Approvals
Fire Integrity 120 minutes BS 476: Part 20
Insulation 120 minutes Mixed services
Air Tightness passing through
Age Testing 30 years Unlined Drywall
Max 1000 mm
CP 670 Coated Batt - Face fixed to
100 mm Drywall screws plasterboard with Drywall screws.
with oversized washers CP 606 Mastic should be used to coat any
exposed mineral wool at the batt edges
Max 1000 mm
service item and coated batt
100 mm
CP 606 to seal between
service item and coated batt
CP 670 batt to be
bedded on CP 606
at the junction with
the Plasterboard.
- CP 670 coated batt must be installed in accordance with manufacturer's guidelines, utilising CP 606 fire rated acoustic mastic at all batt to batt
and batt to substrate junctions. The batt should overlap the plasterboard by a minimum of 100 mm on all edges.
- CP 670 coated batt must be fixed back to the plasterboard partition utilising min 100 mm long drywall screws and oversized washers. The
fixings must be at nom 150 mm ctrs on the horizontal and 200 mm ctrs on vertical edges.
- Butt joints between coated batts are permitted provided that each section of batt is fixed on 3 sides. Joints within the batt should be staggered
from face to face such that no direct through gap exists between the two layers i.e. horizontal joints on one face and vertical joints on the other.
- All service items must be supported either side of the proposed seal system. The fire performance of the seal is only good as that of the
supporting construction and as such the structural adequacy of the partition must be guaranteed.
The above applications are not
exhaustive. For further details
please contact
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
- CP 670 coated batt must be installed in accordance with manufacturer's guidelines, utilising CP 606 fire rated acoustic mastic at all batt to batt
and batt to substrate junctions. The batt should overlap the plasterboard by a minimum of 100 mm on all edges.
- CP 670 coated batt must be fixed back to the plasterboard partition utilising min 100 mm long drywall screws and oversized washers. The
fixings must be at nom 150 mm ctrs on the horizontal and 200 mm ctrs on vertical edges.
- Butt joints between coated batts are permitted provided that each section of batt is fixed on 3 sides. Joints within the batt should be staggered
from face to face such that no direct through gap exists between the two layers i.e. horizontal joints on one face and vertical joints on the other.
- All service items must be supported either side of the proposed seal system. The fire performance of the seal is only good as that of the
supporting construction.
- The CP 645 Firesleeve must be installed in accordance with the manufacturer's guidelines and ensuring that it projects by a minimum of 25 mm
on each face of the seal. The CP 670 coated batt must be installed tightly around the CP 645 such that the sleeve is secured under a slight
compression.
The above applications are not
exhaustive. For further details
please contact
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
Standard firestop detail
APPLICATION
CP 670 Type B Firestop seal to Fire
Damper
Test Up to Approvals
Fire Integrity 60 minutes BS 476 Pt 20
Insulation n/a EN 1366-3 Damper
Acoustics 52 dB installed within
Air Tightness √ Solid or partition wall
Age Testing 30 years
500 mm 500 mm
maximum maximum M10 drop rods anchored to
soffit with fire rated anchors
capable of providing load
1000 mm max.
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
A A
CP 670 Board
fastened to
channel frame
(Detail B-B)
1200 mm
B B
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
DETAIL A-A
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
DETAIL B-B
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
APPLICATION
1. The application limits on this detail are for guidance purposes only. For
more detailed information on the full range of available test results
please contact a Hilti Firestop Specialist on 0800 886100.
2. The product and application has been fire tested as a minimum to BS
476. It may have additional European and worldwide testing. Please
contact Hilti for further information.
3. All installations should be carried out in accordance with Hilti's
installation instructions, by competent, experienced installers using Hilti
branded products.
MM C 30 x 3m 418776 40 lengths
MM A 90 418757 150 Pre-assembled right angled
connector
Fixing the MM-30 frame to the substrate will depend on the substrate itself
Possible additions to schedule – check Hilti Product Catalogue for or contact Firestop Specialist for item numbers.
M8 threaded rod
M8 saddles for fixing rod holding pipe clamps etc.
M6 saddles for taking roofing bolts for fixing tray
M6 roofing bolts
Pipe rings for holding pipes integral to framed system
MM Channel bases
DS 686 Iss 2
Type A
- Single 50 mm layer of pre coated CP 670 with services independently supported on either side of seal
- For use in apertures up to 2400 mm high by 1200 mm wide or 1200 mm high by 5000 mm wide
- Fire Resistance: Integrity & Insulation
(See Standard detail FS 047-05 Hilti CP670 Firestop acoustic board type A)
30 60 90 120 180 240
Int Ins Int Ins Int Ins Int Ins Int Ins Int Ins
Blank Seals
Small Diameter Individual Cables (<20mm)
Medium Diameter Individual Cables (21 to 40
C 1
mm)
Large Diameter Individual Cables (41 to 75
1
mm)
Small diameter bunched cables (<20 mm)
Medium Diameter Bunched Cables (21 to 40
C 1
mm)
Large Diameter bunched Cables (41 to 75
1
mm)
Cable trays/ladders
Trunking up to 250 x 250 mm* 2 2 2
Steel/cast iron pipes up to 250 mm diameter 2 2 2
PVC pipes up to 110 mm dia using CP 643 S S
PP,ABS Plastic Pipes Up to 110 mm dia CP645
Copper pipes up to 108 mm diameter 2 2 2 2
PVC Pipes Up to 168 mm diameter CP645
1 = requires CP 611A (See Standard detail FS080-02 Hilti CP611A High pressure intumescent sealant)
2 = Insulation ratings can be achieved on Steel & Copper pipes by using CP645 Fire Sleeves with a projection
of 500 mm or 25 mm from each face and taped to existing fire resistant pipe insulation(See Standard
detail “FS005-02 Hilti CP645 intumescent firesleeve”)
*= Inside of Trunking to be sealed with CP 651N cushions
C = Requires Coatback (Coat service items as required for either 100mm(90mins insulation) or 150mm
(120mins insulation value)on either side of the seal with CP670C fire safety coating.
S = surface mounted and fixed with M8 threaded rod nuts and washers
Insulation ratings can be achieved on trunking by using appropriate insulation
Ensure All services are adequately supported within 500mm of both faces of the seal See ”DS 0676 Iss 1
Fireseals and supports for Building Services”
Hilti (Gt. Britain) Limited, 1 Trafford Wharf Road, Trafford Park, Manchester M17 1BY Telephone: 0800 886 100
Data Sheet - sheet 2 of 3
DS 686 Iss 2
Type B
- Multi Layer CP 670 of 100 mm minimum overall Board thickness
- No internal framing.
- For use in apertures up to 1200 mm high by any length wide.
Fire Resistance: Integrity & Insulation
(See Standard detail FS 050-05 Hilti CP670 Firestop acoustic board type B)
30 60 90 120 180 240
Int Ins Int Ins Int Ins Int Ins Int Ins Ins Int
Blank Seals
C C C C C C
Small Diameter Individual Cables (<20mm) C
Medium Diameter Individual Cables (21 to 40
C C C C C C C
mm)
Large Diameter Individual Cables (41 to 75
C C C C C C C
mm)
Small diameter bunched cables (<20 mm) C C C C C C C
Medium Diameter Bunched Cables (21 to 40
C C C C C C
mm) C
C C C C C C
Cable trays/ladders C
Trunking up to 250 x 250 mm* C C C C C C C
Duct and Damper up to 1000 mm Square
Steel/cast iron pipes up to 200 mm diameter
(insulated)
UPVC Pipe up to 110 mm With CP643 2 2
Copper pipes up to 108 mm diameter
1 = requires CP 611A (See Standard detail FS080-02 Hilti CP611A High pressure intumescent sealant)
2 = Surface mounted only
C = Requires Coatback (Coat service items as required for either 100mm(90mins insulation) or 150mm (120mins
insulation value) on either side of the seal with CP670C fire safety coating.
*= Inside of Trunking to be sealed with CP 651N cushions
Ensure All services are adequately supported within 500mm of both faces of the seal See ”DS 0676 Iss 1 Fireseals
and supports for Building Services”
Hilti (Gt. Britain) Limited, 1 Trafford Wharf Road, Trafford Park, Manchester M17 1BY Telephone: 0800 886 100
Data Sheet - sheet 3 of 3
DS 686 Iss 2
Type C
- Multi Layer CP 670 of 100 mm minimum overall Board thickness
- Internal profiled steel support frame of MMC30
- For use in apertures up to 5000 mm high by any length wide.
Fire Resistance: Integrity & Insulation
(See Standard detail FS118-02)
30 60 90 120 180 240
Int Ins Int Ins Int Ins Int Ins Int Ins Int Ins
Blank Seals
Small Diameter Individual Cables (<20mm) C
Medium Diameter Individual Cables (21 to 40
mm) C
Large Diameter Individual Cables (41 to 75
mm)
Small diameter bunched cables (<20 mm) C
Medium Diameter Bunched Cables (21 to 40
mm) C
Cable trays/ladders
Trunking up to 250 x 250 mm*
Duct and Damper up to 1000 mm Square
Steel/cast iron pipes up to 200 mm diameter
UPVC Pipe up to 110 mm With CP643 2 2
Copper pipes up to 108 mm diameter
1 = requires CP 611A
2 = Surface mounted only
*= Inside of Trunking to be sealed with CP 651N cushions
C= = Requires Coatback (Coat service items 150mm (120mins insulation value) on either side of the seal with
CP670C fire safety coating
Ensure All services are adequately supported within 500mm of both faces of the seal See ”DS 0676 Iss 1
Fireseals and supports for Building Services
IMPORTANT NOTES
1. The information and recommendations given herein are believed to be correct at the time of writing. The
data has been obtained from tests done under laboratory, or other controlled, conditions and it is the
users’ responsibility to use the data given in the light of conditions on site and taking account of the
intended use of the products concerned. Whilst Hilti (Gt. Britain) Limited can give general guidance and
advice, the nature of Hilti products means that the ultimate responsibility for selecting the correct product
for a particular application must lie with the customer.
2. All products must be used, handled and applied in accordance with current instructions for use published
by Hilti (Gt. Britain) Limited.
3. All products are supplied, and advice given, subject to Hilti (Gt. Britain) Limited terms of business.
4. Hilti’s policy is one of continuous development. We therefore reserve the right to alter specifications etc.
without notice.
5. Construction materials and conditions vary on different sites. If it is suspected that the base material has
insufficient strength to achieve a suitable fixing, contact the Hilti Technical Advisory Service.
Hilti (Gt. Britain) Limited, 1 Trafford Wharf Road, Trafford Park, Manchester M17 1BY Telephone: 0800 886 100
CP 670
Fire BS 476 - 20
BS EN 1366-3
Certifire 663
Ageing DIBT
DAfSTB
Fire test after ageing
BREEAM Section
Advantages
• Adheres to concrete, drywall and masonry
• Approval for virtually any transit type — cables, trays, conduits and pipes (metal
and plastic)
• Up to 6 times expansion
• Suitable for complex and difficult-to-reach applications — single-sided
installation possible and no reinforcing material needed
• Cures within 60 seconds
• Mold, mildew, water and vapor resistant
• Future-proof — re-penetrable to allow future cable capacity increases
• Optimal smoke tightness according to DIN EN 1026 and ASTM E 283-04
Installation instructions
• See Hilti literature or third-party listings for complete application and installation
details
Volume per cartridge & foam yield (up to) 300ml & 116 in³
through innovation
and education
Product information
Technical data*
Chemical basis Water-based acrylic dispersion
Color Available in red, white and gray
Density 99.9 lb/ft³
Application temperature 35°F to 104°F (1.5°C to 40°C)
Storage temperature 35°F to 95°F (1.5°C to 35°C)
Temperature resistance -22°F to 176°F (-30°C to 80°C)
Shelf life 24 months
Tack free time 23mins (ventilated at 77°F, 80% rel. humidity) FILL, VOID OR CAVITY MATERIAL
FOR USE IN THROUGH-PENETRATION
Skin-forming time Approx. 15 min FIRESTOP SYSTEMS AND
Curing time Approx. 3 mm / 3 days JOINT SYSTEMS
SEE UL FIRE RESISTANCE DIRECTORY
Average volume shrinkage (ASTM C1241) 22% 66Y7
Movement capability Up to 33%
Mold & mildew Class 0 (ASTM G21-96)
Electrical resistance Yes
LEED Compliant Yes (CDPH v1.2-2017)
LEED VOC 63 g/L
Intumescent No
Seismic resistant Yes
Water tightness Yes
Temperature resistance –22°F to 176°F (–30°C to 80°C)
Surface burning characteristics Flame Spread: 10
(ASTM E 84-96) Smoke Development: 0
Surface burning characteristics Flame Spread: 14
(CAN/ULC-S102) Smoke Developed: 4
California State Fire Marshall Approvals Yes (pens & joints)
City of New York approval Yes (CP606 MEA 100-99-MV6)
Air leakage (UL 2079 L-Rating) L-Rating at Ambient = Less than 1 CFM / Lin Ft.
L-Rating at 400%F = Less than 1 CFM / Lin Ft.
Sound transmission classification 56
(ASTM E 90-99) (Relates to specific construction)
DBS • 03/22
Tested in accordance with UL 2079, ASTM E 814, ASTM E 1966, ASTM E 84,
UL 1479, ASTM G21, ASTM C1241, CAN/ULC-S115
*At 73°F (23°C) and 50% relative humidity
Hilti Firestop
Saving lives
through innovation
and education
Strut Channel System
Single
Strut is used in various industries as light
structural support for tray systems and other
mechanical components. Metal Framing Channels
are accurately and carefully cold-formed to size
1 P-SUC-3-H 3 8.25 Kg
2 P-SUC-6-H 6 16.5 Kg
Material: Finishing:
- Sheet Steel - Hot Dipped Galvanised (HDG) - Powder Coating
- Paint - Electro galvanize / zinc plating, etc
STEEL
CITY
Specification
HDG. Conduit Fitting
E.M.T. CONNECTOR
Ø D
Cat.,No. Cat.,No.
H-MEN11~MEN13 H-MEN14~H-MEN16
STEEL
CITY
Specification
HDG. Conduit Fitting
E.M.T. COUPLING
ØD
Cat.,No. Cat.,No.
H-MEP11~H-MEP13 H-MEP14~H-MEP16
IP RATING COLOUR SIZE
IP65 WHITE M25
40.0
34.3
CABLE ANCHORAGE
7 - 13 © 2013 Essentra Components. All rights reserved.
FOR CABLE 25.5 Registered in England, Company No. 547495.
Registered Office: Avebury House,
201-249 Avebury Boulevard, Milton Keynes, MK9 1AU
SHEET
DWG. No.
1 of 1
APPROVED - UNCONTROLLED 1664671 ISSUE
1
Saddle Application:
To support and securely fasten rigidmetal conduit
Clamp
to the supporting surface. saddle clamps present
a dependable cable & pipe conduit management
solution. With a screw hole for affixing to almost
any surface, these versatile saddle clamps can hold
pipes and cables in place securely.
FOR D W T A L Ø
PART No. MATERIAL FINISHING.
CONDUIT SIZE (mm) (mm) (mm) (mm) (mm) (mm)
Material: Finishing:
- Steel - Hot Dipped Galvanized (HDG)
- Stainless Steel ( SS 304 & SS 316 ) - Electro Galvanized
- Natural