Professional Documents
Culture Documents
Non-isolated Buck
LED Driver Regulator
Parameters Subject to Change Without Notice
DESCRIPTION FEATURES
JWB®1997M/A is a non-isolated constant current 800V Bridge Rectifier Integrated
LED regulator with high current accuracy which 600V Low VF Diode Integrated
applies to step-down LED drivers. Operating in 500V MOSFET Integrated
the boundary mode makes it high efficiency and Excellent line/load regulation
low radiation. Patented algorithms ensure good Boundary mode operation
without auxiliary winding or external capacitor, Optimized the Ipeak mutation problem
which can lower the system BOM cost. Optimized the problem of unreasonable
TYPICAL APPLICATION
RS
JWB1997M/A
ORDER INFORMATION
Note:
JW # TRPBF
PB Free
1) Tape and Reel(If”TR”is not shown, it means tube)
Package Code
Part No.
YW
JW
Lot number
2) Line1: Product code Line2:
Joulwatt LOGO Week code
Year code
DEVICE INFORMATION
DEVICE MOS BV MOS RDSON OUTPUT CURRENT
PIN CONFIGURATION
TOP VIEW
ACIN2 1 7 ACIN1
GND 2 6 VIN
NC 3
CS 4 5 DRAIN
ASOP-7
Note:
1) Exceeding these ratings may damage the device.
2) The JWB1997M/A guarantees robust performance from -40°C to 150°C junction temperature. The junction
temperature range specification is assured by design, characterization and correlation with statistical process
controls.
3) The JWB1997M/A includes thermal protection that is intended to protect the device in overload conditions. Thermal
protection is active when junction temperature exceeds the maximum operating junction temperature. Continuous
operation over the specified absolute maximum operating junction temperature may damage the device.
4) Measured on JESD51-7, 4-layer PCB.
5) The maximum output current is recommended in the application according to chip junction temperature TJ=125℃
(chip case temperature difference about 20℃). The maximum output current could be increased properly if the heat
dissipation is better.
6) Limit by chip temperature.
ELECTRICAL CHARACTERISTICS
Drain-source Vg=0V
JWB1997M/A BVDSS 500 V
Voltage Ids=250uA
JWB1997M Vg=15V 13 14
MOS RDSON RDS_ON ohm
JWB1997A Ids=0.5A 8 9
DS Leakage Vg=0V
JWB1997M/A IDSS 1 5 uA
Current Vds=500V
IF=0.5A,IR=1A,
Diode Reverse Recovery time7) TRR 35 ns
IFF=0.25A
Notes:
7) Guaranteed by design
PIN DESCRIPTION
3 NC Not Connected
BLOCK DIAGRAM
600V
ES1JP
ACIN2
Power Supply
CS
Comparator Reset
400mV Tonmax
Vg
RS Latch Gate Driver
OTP
ZCD Set
Toffmax
GND CS
FUNCTIONAL DESCRIPTION
components. Ipk
Start Up IL
JWB1997M/A controls the output current from the TON = 2 ILED×L / (VIN – VLED)
information of the current sensing resistor. The Where,
output LED average current can be calculated as: L –inductance.
ILED = VREF /(2 RCS) ILED – output led current.
Where, VIN – input voltage after rectification and filtering.
VREF is the reference voltage; VLED – output voltage.
RCS – the sensing resistor connected between the When the power MOSFET turns off, the inductor
PIN CS and chip GND. current decreases. The power MOSFET turns on
The inductor current and VRS waveforms are as again when the inductor current is zero. The
follows: turn-off time of the MOSFET can be calculated
Where, as:
VRS – the voltage between PIN CS and chip GND. TOFF = 2 ILED×L / VLED
JWB1997M/A works in quasi-resonant mode.
VREF
When the inductor current decreases to zero,
VRS
resonance takes place between the power
0V
inductor, MOSFET output capacitor and
Ipeak stray capacitor. JWB1997M/A can detect the
ILED zero-current signals of the inductor, and turn on
0 the MOSFET in the valley, which can reduce the
Inductor Current
power loss and the EMI radiation. If JWB1997M/A
cannot get the zero current signals, the turn off
Critical Conduction Mode Operation time will be changed to TOFFMAX. The output
voltage should be higher than recommended
JWB1997M/A works in the critical conduction
voltage in order to avoid the loss of zero current
mode of the inductor current. When the power
signals.
MOSFET turns on, the inductor current increases
from zero linearly. The turn on time of the
MOSFET can be calculated as:
APPLICATION REFERENCE
This reference design is suitable for 10~20W non-isolated Step-down LED driver, using JWB1997M/A,
with high efficiency, excellent line regulation.
Reference :
VIN: 90VAC~260VAC
VOUT: 40~80V
IOUT: 200mA
PF: >0.5
L 90-260Vac N
U1
ASOP7
1 ACIN1 5
ACIN2
2 LED+
GND 6
HV
3 C1
C2
NC
Drain 15uF/400V 2.2uF/400V 80V
4 5 R2
CS
160K/1206 200mA
PACKAGE OUTLINE
ASOP-7 UNIT: mm
MILLIMETER
D
Symbol MIN NOM MAX
A 1.25 1.45
A2 A A1 0.20REF
θ
A2 1.05 1.15 1.25
A1 L c 0.15 0.22
D 6.10 6.20 6.30
E 5.90 6.00 6.10
e2 e3 E1 3.80 3.90 4.00
b3 ×
2 b4 e 1.23 1.33 1.43
e1 2.41 2.51 2.61
e2 2.08 2.18 2.28
e3 2.58 2.68 2.78
b 0.30 0.40 0.50
b1 0.41 0.51 0.61
E1 E
b3 0.45 0.55 0.65
b1
b ×
3
e1 e ×
2
IMPORTANT NOTICE
Joulwatt Technology Inc. reserves the right to make modifications, enhancements, improvements,
corrections or other changes without further notice to this document and any product described herein.
Any unauthorized redistribution or copy of this document for any purpose is strictly forbidden.
Joulwatt Technology Inc. does not warrant or accept any liability whatsoever in respect of any products