Professional Documents
Culture Documents
Warning Chime System - Qashqai J11
Warning Chime System - Qashqai J11
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
PRECAUTION ............................................... 3 COMMON ITEM .........................................................18 F
COMMON ITEM : CONSULT Function (BCM -
PRECAUTIONS ................................................... 3 COMMON ITEM) .....................................................18
Precaution for Supplemental Restraint System G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- BUZZER .....................................................................18
SIONER" ................................................................... 3 BUZZER : CONSULT Function (BCM - BUZZER)
Precautions for Removing Battery Terminal ............. 3 (With Intelligent Key System) ..................................19
H
SYSTEM DESCRIPTION .............................. 5 DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) ............................. 20
COMPONENT PARTS ........................................ 5 I
Component Parts Location ........................................ 5 COMMON ITEM .........................................................20
Combination Meter .................................................... 6 COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) .....................................................20
SYSTEM .............................................................. 7 J
BUZZER .....................................................................20
WARNING CHIME SYSTEM ....................................... 7 BUZZER : CONSULT Function (BCM - BUZZER)
WARNING CHIME SYSTEM : System Description (Without Intelligent Key System) .............................21
K
...... 7
WARNING CHIME SYSTEM : Fail-safe .................... 8 ECU DIAGNOSIS INFORMATION .............. 22
LIGHT REMINDER WARNING CHIME ....................... 8 COMBINATION METER ................................... 22 L
LIGHT REMINDER WARNING CHIME : Light Re- Reference Value ......................................................22
minder Warning ......................................................... 8 Fail-safe ...................................................................28
DTC Index ...............................................................29
PARKING BRAKE RELEASE WARNING CHIME ...... 9 M
PARKING BRAKE RELEASE WARNING CHIME BCM (BODY CONTROL MODULE) ................. 30
: Parking Brake Release Warning Chime .................. 9 List of ECU Reference .............................................30
WCS
SEAT BELT REMINDER WARNING CHIME ............ 10 WIRING DIAGRAM ...................................... 31
SEAT BELT REMINDER WARNING CHIME :
Seat belt Warning .................................................... 10 WARNING CHIME SYSTEM ............................. 31
Wiring Diagram ........................................................31 O
KEY WARNING CHIME ............................................. 11
KEY WARNING CHIME : Key Warning Chime ....... 11 BASIC INSPECTION ................................... 38
DIAGNOSIS SYSTEM (COMBINATION DIAGNOSIS AND REPAIR WORK FLOW ....... 38 P
METER) ..............................................................13 Work Flow ................................................................38
Description .............................................................. 13
CONSULT Function (METER/M&A) ....................... 15 DTC/CIRCUIT DIAGNOSIS ......................... 40
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI- POWER SUPPLY AND GROUND CIRCUIT .... 40
GENT KEY SYSTEM) .........................................18 COMBINATION METER ............................................40
WCS-1
COMBINATION METER : Diagnosis Procedure ... 40 Description .............................................................. 48
Component Function Check .................................. 48
BCM (BODY CONTROL SYSTEM) (WITH INTEL- Diagnosis Procedure .............................................. 48
LIGENT KEY SYSTEM) ............................................ 40 Component Inspection ............................................ 49
BCM (BODY CONTROL SYSTEM) (WITH INTEL-
LIGENT KEY SYSTEM) : Diagnosis Procedure ..... 40 SYMPTOM DIAGNOSIS ............................ 50
BCM (BODY CONTROL SYSTEM) (WITHOUT IN- WARNING CHIME SYSTEM SYMPTOMS ........ 50
TELLIGENT KEY SYSTEM) ..................................... 41 Symptom Table ....................................................... 50
BCM (BODY CONTROL SYSTEM) (WITHOUT
INTELLIGENT KEY SYSTEM) : Diagnosis Proce- THE PARKING BRAKE RELEASE WARNING
dure ........................................................................ 41 CONTINUES SOUNDING, OR DOES NOT
SOUND .............................................................. 51
METER BUZZER CIRCUIT ................................ 43 Description .............................................................. 51
Description .............................................................. 43
Diagnosis Procedure ............................................... 51
Component Function Check ................................... 43
Diagnosis Procedure ............................................. 43 THE SEAT BELT REMINDER WARNING
CONTINUES SOUNDING, OR DOES NOT
SEAT BELT BUCKLE SWITCH SIGNAL CIR-
SOUND .............................................................. 52
CUIT ................................................................... 44
Description .............................................................. 52
Description .............................................................. 44
Diagnosis Procedure ............................................... 52
Component Function Check ................................. 44
Diagnosis Procedure ............................................. 44 THE LIGHT REMINDER WARNING DOES
Component Inspection ............................................ 45 NOT SOUND ...................................................... 53
PARKING BRAKE SWITCH SIGNAL CIR- Description .............................................................. 53
Diagnosis Procedure ............................................... 53
CUIT ................................................................... 46
Component Function Check ................................... 46 THE KEY WARNING DOES NOT SOUND
Diagnosis Procedure .............................................. 46 (WITHOUT INTELLIGENT KEY) ....................... 54
Component Inspection ............................................ 47 Description .............................................................. 54
KEY SWITCH SIGNAL CIRCUIT (WITHOUT Diagnosis Procedure ............................................... 54
INTELLIGENT KEY) .......................................... 48
WCS-2
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000010519162
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions for Removing Battery Terminal INFOID:0000000010519172
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key K
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
L
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition M
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
WCS
SEF289H
O
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to Instruction 1 or Instruction 2 described below.
For vehicles parked by ignition switch OFF, refer to Instruction 2. P
INSTRUCTION 1
1. Open the hood.
2. Turn key switch to the OFF position with the driver side door opened.
3. Get out of the vehicle and close the driver side door.
4. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
WCS-3
PRECAUTIONS
< PRECAUTION >
5. Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
WCS-4
COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000010438757
B
H
E1NIA0083ZZ
WCS-5
COMPONENT PARTS
< SYSTEM DESCRIPTION >
Combination Meter INFOID:0000000010438758
The combination meter has a built-in buzzer (1) and sounds the fol-
lowing warnings, according to signals from each switch and unit:
JSNIA5954ZZ
WCS-6
SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
A
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Description INFOID:0000000010438759
B
SYSTEM DIAGRAM (WITH INTELLIGENT KEY SYSTEM)
C
E1NIA0085GB
H
SYSTEM DIAGRAM (WITHOUT INTELLIGENT KEY SYSTEM)
M
E1NIA0084GB
O
Signal name Transmit unit
Vehicle speed signal ABS actuator and electric unit (control unit)
Buzzer output signal BCM P
Output signal
WCS-7
SYSTEM
< SYSTEM DESCRIPTION >
Input signal
Output signal
DESCRIPTION
Combination Meter
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
Function Specifications
Buzzer The buzzer turns OFF by suspending communication.
E1NIA0086GB
WCS-8
SYSTEM
< SYSTEM DESCRIPTION >
Operation conditions A
Ignition switch OFF
Combination switch (Lighting switch) 1st or 2nd position
B
Driver side door Open [front door switch LH ON]
Operation conditions
D
Ignition switch ON
Combination switch (Lighting switch) OFF or AUTO position
Driver side door Close [front door switch LH OFF] E
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below. F
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig- I
nal) from BCM.
SYSTEM DIAGRAM
M
WCS
E1NIA0087GB
P
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
Operation conditions
Ignition switch ON
WCS-9
SYSTEM
< SYSTEM DESCRIPTION >
Operation conditions
Parking brake During the operation (parking brake switch ON)
Vehicle speed Approximately 4.3 MPH (7 km/h) or more
Operation conditions
Ignition switch OFF
Parking brake Release condition (parking brake switch OFF)
Vehicle speed Approximately 1.9 MPH (3 km/h) or less
SIGNAL PATH
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
SYSTEM DIAGRAM
E1NIA0088GB
Operation conditions
Ignition switch ON
Driver seat belt Unfastened [seat belt buckle switch LH ON]
Operation conditions
Ignition switch OFF
Driver seat belt Fastened (seat belt buckle switch LH OFF)
6 seconds after the start of warning sound
SIGNAL PATH
WCS-10
SYSTEM
< SYSTEM DESCRIPTION >
1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below. A
Seat belt buckle switch signal (LH) Seat belt buckle switch (LH) Combination meter BCM
C
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
D
Signal name Signal source
SYSTEM DIAGRAM
G
E1NIA0089GB
Operation conditions K
Ignition switch OFF
Key switch ON (key is in key cylinder)
L
Driver side door Open [front door switch LH ON]
Operation conditions
WCS
Ignition switch ON
Key switch ON (key is removed from key cylinder)
Driver side door Close [front door switch LH OFF] O
SIGNAL PATH
1. BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line. P
WCS-11
SYSTEM
< SYSTEM DESCRIPTION >
Signal name Signal source
2. Combination meter sounds integrated buzzer, when it receives a buzzer output signal from BCM.
WCS-12
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
A
Description INFOID:0000000010438765
2 Part number
3 Software code L
This item is displayed, but not used.
4 EEPROM code
5 Hardware code
6 P.C.B code M
The pointer of the following items moves from 0 to MAX twice.
• Speedometer
• Tachometer WCS
7 Circuit check • Engine coolant temperature gauge
• Fuel gauge
NOTE:
If any one of the pointers does not sweep, replace combination meter. O
8 *1 Performs the color check of the information display.
Color check
WCS-13
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
Test order Test item Description
Displays the error code of the following items:
• Speedometer
• Tachometer
9 error code*2 • Engine coolant temperature gauge
• Fuel gauge
• Meter control switch
All warning/indicator lamp illuminate.
NOTE:
10 Warning/indicator lamp check
• When either one of them does not turn ON, replace combination meter.
• SRS air bag warning lamp and security indicator lamp are not illuminate.
NOTE:
When the trip reset switch is pressed during the indication of Test order “10,” test item returns to Test order “2.”
*1: Color Check
JSNIA5944ZZ
JSNIA5945ZZ
WCS-14
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
Item Code Description Action to take/Reference
A
0 Normal —
0 Normal —
Engine coolant temper- Perform “Self Diagnostic Result” of D
ature gauge An engine coolant temperature signal can-
1 “ECM.”
not be received from ECM.
Refer to ECH-71, "DTC Index".
0 Normal — E
When judging that the illumination control
1 switch signal circuit is shorted for 5 minutes
or more.
Meter control switch Refer to MWI-69, "Diagnosis Proce- F
When judging that the trip reset switch sig-
2 dure".
nal circuit is shorted for 5 minutes or more.
When judging that the both switch signal cir-
3 G
cuit is shored for 5 minutes or more.
— 0 Displays “0” constantly. —
WCS-15
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
X: Applicable
MAIN
Display item [Unit] Description
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
SPEED OUTPUT
X Vehicle speed signal value transmitted to other units via CAN communication.
[mph or km/h]
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[mph or km/h]
TACHO METER
X Value of the engine speed signal received from ECM via CAN communication.
[rpm]
FUEL METER
X Fuel level indicated on combination meter.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
[°F] or [°C]
ABS W/L
Displays [On/Off] condition of ABS warning indicator.
[On/Off]
VDC/TCS IND
Displays [On/Off] condition of VDC OFF indicator lamp.
[On/Off]
SLIP IND
Displays [On/Off] condition of SLIP indicator lamp.
[On/Off]
BRAKE W/L
Displays [On/Off] condition of brake warning indicator.
[On/Off]
DOOR W/L Displays [On/Off] condition of door or liftgate warning message in the information
[On/Off] display.
HI-BEAM IND
Displays [On/Off] condition of high beam indicator.
[On/Off]
TURN IND
Displays [On/Off] condition of turn indicator.
[On/Off]
LIGHT IND
Displays [On/Off] condition of light indicator.
[On/Off]
FR FOG IND
Displays [On/Off] condition of front fog lamp indicator.
[On/Off]
OIL W/L Displays [On/Off] condition of low engine oil pressure warning message in the in-
[On/Off] formation display.
O/D OFF IND
Displays [On/Off] condition of O/D OFF indicator.
[On/Off]
DDS W/L
Displays [On/Off] condition of hill descent control warning indicator.
[On/Off]
MIL
Displays [On/Off] condition of malfunction indicator.
[On/Off]
SPORT IND
Displays [On/Off] condition of SPORT indicator.
[On/Off]
CHAGE W/L
Displays [On/Off] condition of charge warning indicator.
[On/Off]
4WD LOCK IND
Displays [On/Off] condition of AWD LOCK indicator lamp.
[On/Off]
4WD W/L
Displays [On/Off] condition of AWD warning message in the information display.
[On/Off]
FUEL W/L
Displays [On/Off] condition of low-fuel warning message.
[On/Off]
WASHER W/L
Displays [On/Off] condition of low washer fluid warning message.
[On/Off]
WCS-16
DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS A
AIR PRES W/L
Displays [On/Off] condition of tire pressure warning lamp.
[On/Off]
KEY G/Y W/L B
Displays [On/Off] condition of key green warning lamp.
[On/Off]
EPS W/L
Displays [On/Off] condition of EPS warning indicator.
[On/Off] C
LCD Displays the value of Intelligent Key system message indication.
SHIFT IND
Displays shift selector position.
[P, R, N, D, L] D
FUEL CAP W/L
Displays [On/Off] condition of loose fuel cap warning message.
[On/Off]
O/D OFF SW E
Displays [On/Off] condition of O/D Off switch.
[On/Off]
PKB SW
Displays [On/Off] condition of parking brake switch.
[On/Off] F
BUCKLE SW
Displays [On/Off] condition of seat belt buckle switch LH.
[On/Off]
PASS BUCKLE SW G
Displays [On/Off] condition of seat belt buckle switch RH.
[On/Off]
BRAKE OIL SW
Displays [On/Off] condition of brake fluid level switch.
[On/Off] H
DISTANCE
Displays distance to empty.
[Mi] or [km]
OUTSIDE TEMP
Displays the ambient air temperature which is input from the ambient sensor.
I
[°F or °C]
FUEL LOW SIG
Displays [On/Off] condition of low-fuel warning signal.
[On/Off] J
STRG SW INPUT
Displays [SW 1-SW 10, NOT INPUT] condition of steering switches.
[SW 1-SW 10, NOT INPUT]
Buzzer status (in the combination meter) is detected from the buzzer output signal K
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off]
of the combination meter.
BSW IND
Displays [On/Off] condition of blind spot warning indicator. L
[On/Off]
BSW W/L Displays [On/Off] condition of blind spot warning message in the information dis-
[On/Off] play.
M
SPECIAL FUNCTION
Special menu
WCS
Display item Description
W/L ON HISTORY Lighting history of warning lamp and indicator lamp can be checked.
O
W/L ON HISTORY
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
P
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: No warning/indicator lamp history is stored.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
WCS-17
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010438767
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEADLAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
TPMS AIR PRESSURE MONITOR × × × ×
BUZZER
WCS-18
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
BUZZER : CONSULT Function (BCM - BUZZER) (With Intelligent Key System)
INFOID:0000000010438768 A
DATA MONITOR
B
Monitor Item [Unit] Description
PUSH -SW [On/Off] Indicates condition of push-button ignition switch.
VEH SPEED 1 [km/h] Indicates vehicle speed signal received from ABS on CAN communication line. C
TAIL LAMP SW [On/Off] Indicates condition of combination switch.
FR FOG SW [On/Off] Indicates condition of front fog lamp switch.
D
DOOR SW-DR [On/Off] Indicates condition of front door switch LH.
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
E
ACTIVE TEST
WCS
WCS-19
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000010438769
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT ×
Exterior lamp HEADLAMP × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
TPMS AIR PRESSURE MONITOR × × × ×
BUZZER
WCS-20
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
BUZZER : CONSULT Function (BCM - BUZZER) (Without Intelligent Key System)
INFOID:0000000010438770 A
DATA MONITOR
B
Monitor Item [Unit] Description
TAIL LAMP SW [On/Off] Indicates condition of combination switch.
DOOR SW-DR [On/Off] Indicates condition of front door switch LH. C
CDL LOCK SW [On/Off] Indicates condition of lock signal from door lock and unlock switch.
ACTIVE TEST D
WCS
WCS-21
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION
COMBINATION METER
Reference Value INFOID:0000000010503091
WCS-22
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
NOTE:
Ignition switch
RR FOG IND This item is displayed, but cannot be moni- Off
ON
tored.
WCS-23
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
NOTE:
DPF W/L Engine running This item is displayed, but cannot be moni- Off
tored.
NOTE:
Ignition switch
TRAILER IND This item is displayed, but cannot be moni- Off
ON
tored.
During the indication of “P” by shift position
P
indicator
During the indication of “R” by shift position
R
indicator
During the indication of “N” by shift position
N
indicator
During the indication of “D” by shift position
D
indicator
During the indication of “L” by shift position
L
indicator
Ignition switch
SHIFT IND During the indication of “M1” by shift posi-
ON M1
tion indicator
During the indication of “M2” by shift posi-
M2
tion indicator
During the indication of “M3” by shift posi-
M3
tion indicator
During the indication of “M4” by shift posi-
M4
tion indicator
During the indication of “M5” by shift posi-
M5
tion indicator
During the indication of “M6” by shift posi-
M6
tion indicator
WCS-24
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
DISTANCE Ignition switch Distance to empty calculated by com-
—
[km] ON bination meter
Input value ofoutside temperature
sender sensor signal (CAN communi- B
OUTSIDE TEMP Ignition switch cation signal)
—
[°C or °F] ON NOTE:
This may not match the indicated value
on the information display.
C
JSNIA0457ZZ
PHYSICAL VALUES L
Terminal No.
Description
(Wire color) Value M
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition WCS
1
Ground Ground 1 — switch — 0V
(B)
ON
Ignition Security warning lamp ON 0V O
7
Ground Security signal Input switch
(L) Security warning lamp OFF 12 V
OFF
Ignition ECO MODE switch ON 0V
9 P
Ground ECO MODE switch signal Input switch
(P) ECO MODE switch OFF 12 V
OFF
WCS-25
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
15 Outside temperature send-
Ground Input switch —
(BG) er (ambient sensor) signal
ON
JSNIA0014GB
Ignition
17
Ground Satellite switch ground — switch — 0V
(BG)
ON
Ignition TRIP RESET switch ON 12 V
18
Ground TRIP RESET SWITCH Input switch
(SB) TRIP RESET switch OFF 0V
OFF
Ignition
20 Outside temperature sen-
Ground — switch — 0V
(R) sor ground
ON
Ignition
21 Steering switch (trip com-
Ground Input switch — 0V
(L) puter) ground
ON
Ignition Press the steering switch 0V
22 Steering switch (trip com-
Ground Input switch
(LG) puter) input A signal Other than above 5V
ON
Ignition Press the steering switch 0V
23 Steering switch (trip com-
Ground Input switch
(GR) puter) input B signal Other than above 5V
ON
WCS-26
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition When illumination switch (-) B
0V
37 Illumination control switch switch is pressed
Ground Input
(V) signal (-) OFF or
ON Other than above 5V
C
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). D
Ignition Speedometer operated
38 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(P) (8-pulse)
ON prox. 40 km/h (25 MPH)] E
JSNIA0015GB F
41
— CAN-H — — — —
(L)
42 G
— CAN-L — — — —
(P)
H
• Lighting switch 1ST posi-
tion
• When meter illumination
is maximum
I
JPNIA1687GB
J
Ignition
43
Ground Illumination control signal Output switch
(R) • Lighting switch 1ST posi-
ON
tion K
• When meter illumination
is step 11
L
JPNIA1686GB
WCS-27
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
49 50
Oil level sensor signal Input switch —
(V) (P)
ON
JSNIA3463ZZ
Ignition
51 44
Fuel level sensor signal Input switch —
(G) (B)
ON
JSNIA3463ZZ
Ignition
52
Ground Ground 2 — switch — 0V
(B)
ON
Fail-safe INFOID:0000000010503092
The combination meter activates the fail-safe control if the CAN communication lines between each unit are
malfunctioning.
Function Specifications
Speedometer
Tachometer Reset to zero by suspending communication.
Engine coolant temperature gauge
When suspending communication, changes to
Meter illumination control
nighttime mode.
Buzzer Turned off by suspending communication.
Current fuel consumption • When reception time of an abnormal signal is
2 seconds or less, the last received datum is
Average fuel consumption
used for calculation to indicate the result.
Average vehicle speed • When reception time of an abnormal signal is
Trip computer more than 2 seconds, the last result calculat-
Range (Distance to empty) ed during normal condition is indicated.
An indicated value is maintained at communica-
Driving distance
tions blackout.
Information dis-
play Door open warning
The indicator turns OFF by suspending commu-
Interrupt indication Low tire pressure warning
nication.
Fuel filler cap warning
An indicated value is maintained at communica-
Odo/trip meter
tions blackout.
The indicator turns OFF by suspending commu-
Shift position indicator
nication.
WCS-28
COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Function Specifications
A
ABS warning lamp
Brake warning lamp
EPS warning lamp B
Turned on by suspending communication.
VDC warning lamp
AWD warning lamp
Malfunction indicator lamp C
VDC OFF indicator lamp
Warning lamp/ SPORT mode indicator lamp
D
indicator lamp
AWD LOCK indicator lamp
Oil pressure warning lamp
Turned off by suspending communication.
High beam indicator lamp E
Turn signal indicator lamp
Position lamp indicator lamp
F
A/T CHECK indicator lamp
After blinking for 1 minute, the lamp remains
Low tire pressure warning lamp
ON.
G
DTC Index INFOID:0000000010438773
H
Display contents of CONSULT Diagnostic item is detected when... Refer to
CAN COMM CIRCUIT Combination meter is not transmitting or receiving CAN communication signal for 2 MWI-56,
[U1000] seconds or more. "DTC Logic" I
CONTROL UNIT (CAN) MWI-57,
Detecting error during the initial diagnosis of CAN controller of combination meter.
[U1010] "DTC Logic"
VEHICLE SPEED The abnormal vehicle speed signal is input from ABS actuator and electric unit (con- MWI-58, J
[B2205] trol unit) for 2 seconds or more. "DTC Logic"
ENGINE SPEED MWI-59,
ECM continuously transmits abnormal engine speed signals for 2 seconds or more.
[B2267] "DTC Logic" K
WATER TEMP ECM continuously transmits abnormal engine coolant temperature signals for 60 MWI-60,
[B2268] seconds or more. "DTC Logic"
L
WCS
WCS-29
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
List of ECU Reference INFOID:0000000010438774
ECU Reference
BCS-64, "Reference Value"
BCS-88, "Fail-safe"
BCM
BCS-89, "DTC Inspection Priority Chart"
BCS-90, "DTC Index"
WCS-30
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
WARNING CHIME SYSTEM
Wiring Diagram INFOID:0000000010438775
B
WCS
JRNWD1341GB
WCS-31
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JRNWE0830GB
WCS-32
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JRNWE0831GB
WCS-33
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JRNWE0832GB
WCS-34
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JRNWE0833GB
WCS-35
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
JRNWE0834GB
WCS-36
WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WCS
JRNWE0835GB
WCS-37
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow INFOID:0000000010438776
OVERALL SEQUENCE
JSNIA4485GB
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
>> GO TO 2.
2.CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform "self-diagnosis". Refer to WCS-29, "DTC Index".
WCS-38
DIAGNOSIS AND REPAIR WORK FLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow INFOID:0000000010438776
B
OVERALL SEQUENCE
C
JSNIA4485GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform "self-diagnosis". Refer to WCS-29, "DTC Index".
WCS-39
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure INFOID:0000000010438777
1.CHECK FUSES
Check that the following fuses are not blown.
Terminals
(+) Continuity
(–)
Connector Terminal
M51 1
Ground Yes
M52 52
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure INFOID:0000000010438778
WCS-40
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS A
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
B
COMBINATION METER : Diagnosis Procedure INFOID:0000000010438777
C
Regarding Wiring Diagram information, refer to WCS-31, "Wiring Diagram".
D
1.CHECK FUSES
Check that the following fuses are not blown.
E
Unit Power source Fuse No.
Battery 2
Combination meter
Ignition switch ON or START 3 F
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
G
NO >> GO TO 2.
2.POWER SUPPLY CIRCUIT CHECK
1. Disconnect combination meter connector. H
2. Check voltage between combination meter harness connector M52 terminals 45, 46 and ground.
Terminals
(+) Continuity WCS
(–)
Connector Terminal
M51 1
Ground Yes
M52 52 O
Is the inspection result normal?
YES >> Inspection End.
P
NO >> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure INFOID:0000000010438778
WCS-41
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
Regarding Wiring Diagram information, refer to WCS-31, "Wiring Diagram".
1. CHECK FUSE
Check that the following fuse is not blown.
BCM Voltage
Ground
Connector Terminal (Approx.)
BCM
Ground Continuity
Connector Terminal
146
M69 — Yes
147
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connectors.
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure INFOID:0000000010438779
1. CHECK FUSE
Check that the following fuse is not blown.
• The buzzer for the warning chime system is installed in the combination meter. B
• The combination meter sounds the buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000010438781
C
1. CHECK OPERATION OF METER BUZZER
1. Select "BUZZER" of "BCM" on CONSULT.
2. Perform "LIGHT WARN ALM" or "SEAT BELT WARN TEST" of "ACTIVE TEST". D
Does meter buzzer activate?
YES >> Inspection End.
NO >> Refer to WCS-43, "Diagnosis Procedure". E
F
1.CHECK COMBINATION METER INPUT SIGNAL
Select the "Data Monitor" for the "METER/M&A" and check the "BUZZER" monitor value.
G
Monitor item Condition Status
Under the condition of buzzer input On
BUZZER
Except above Off H
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-80, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-132, "Removal and Installation". I
W CS
WCS-43
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
Description INFOID:0000000010438783
Combination meter
Voltage
Terminals Condition
Connector (Approx.)
(+) (-)
When seat belt driver side is fastened Battery voltage
M51 28 Ground
When seat belt driver side is unfastened 0V
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-80, "Removal and Installation".
NO >> GO TO 2.
2. CHECK SEAT BELT BUCKLE SWITCH DRIVER SIDE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter harness connector M51 and seat belt buckle switch driver side harness
connector B11 or B69.
3. Check continuity between combination meter harness connector M51 terminal 28 and seat belt buckle
switch LH harness connector B11 or B69 terminal 1.
B11 (LHD)
M51 28 1 Yes
B69 (RHD)
4. Check continuity between combination meter harness connector M51 terminal 28 and ground.
WCS-44
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
A
Description INFOID:0000000010438783
J
Combination meter
Voltage
Terminals Condition
Connector (Approx.)
(+) (-) K
When seat belt driver side is fastened Battery voltage
M51 28 Ground
When seat belt driver side is unfastened 0V
L
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-86, "Removal and Installation".
NO >> GO TO 2.
M
2. CHECK SEAT BELT BUCKLE SWITCH DRIVER SIDE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter harness connector M51 and seat belt buckle switch driver side harness WCS
connector B11 or B69.
3. Check continuity between combination meter harness connector M51 terminal 28 and seat belt buckle
switch LH harness connector B11 or B69 terminal 1.
O
WCS-45
PARKING BRAKE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Component Function Check INFOID:0000000010438787
1.CONNECTOR INSPECTION
1. Turn ignition switch OFF.
2. Disconnect combination meter and parking brake switch connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace as necessary.
2.CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to WCS-47, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-146, "Removal and Installation".
3.CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT.
1. Connect combination meter connector and parking brake switch connectors.
2. Turn ignition switch ON.
3. In DATA MONITOR select "PKB SW" and check parking brake switch signal.
WCS-46
PARKING BRAKE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
A
Component Function Check INFOID:0000000010438787
1.CONNECTOR INSPECTION F
1. Turn ignition switch OFF.
2. Disconnect combination meter and parking brake switch connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
G
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace as necessary. H
2.CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to WCS-48, "Component Inspection".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-145, "Removal and Installation".
J
3.CHECK PARKING BRAKE SWITCH SIGNAL
With CONSULT.
1. Connect combination meter connector and parking brake switch connectors. K
2. Turn ignition switch ON.
3. In DATA MONITOR select "PKB SW" and check parking brake switch signal.
L
Condition DATA MONITOR
Actuate parking brake On
Release parking brake Off M
Is the inspection result normal?
YES >> Refer to WCS-39, "Work Flow".
NO >> GO TO 4. WCS
WCS-47
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
< DTC/CIRCUIT DIAGNOSIS >
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
Description INFOID:0000000010438790
Terminals
(+) Voltage
Condition
(−) (Approx.)
BCM
Terminal
connector
Key is inserted Battery voltage
M69 81 Ground
Key is removed 0V
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK KEY SWITCH CIRCUIT
1. Disconnect BCM connector M69 and key switch.
2. Check continuity between BCM harness connector M69 terminal 81 and key switch harness connector
M105 terminal 1.
BCM
Continuity
Connector Terminal Ground
M69 81 No
Is the inspection result normal?
YES >> GO TO 3.
WCS-48
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
< DTC/CIRCUIT DIAGNOSIS >
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
A
Description INFOID:0000000010438790
D
Monitor Item Condition Status
When key is removed from key cylinder OFF
KEY ON SW
When key is inserted into key cylinder ON E
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS-49, "Diagnosis Procedure". F
G
Regarding Wiring Diagram information, refer to WCS-31, "Wiring Diagram".
H
1. CHECK BCM INPUT SIGNAL
Check voltage between BCM harness connector M19 terminal 81 and ground.
I
Terminals
(+)
Condition
Voltage J
(−) (Approx.)
BCM
Terminal
connector
Key is inserted Battery voltage K
M69 81 Ground
Key is removed 0V
Is the inspection result normal?
L
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK KEY SWITCH CIRCUIT M
1. Disconnect BCM connector M69 and key switch.
2. Check continuity between BCM harness connector M69 terminal 81 and key switch harness connector
M105 terminal 1. WCS
BCM
Continuity
Connector Terminal Ground
M69 81 No
Is the inspection result normal?
YES >> GO TO 3.
WCS-49
KEY SWITCH SIGNAL CIRCUIT (WITHOUT INTELLIGENT KEY)
< DTC/CIRCUIT DIAGNOSIS >
NO >> Repair or replace harness or connector.
3. CHECK KEY SWITCH POWER SUPPLY CIRCUIT
Check voltage between key switch harness connector M47 terminal 1 and ground.
Terminals
Voltage
(+)
(–) (Approx.)
Key switch Terminal
M47 1 Ground Battery voltage
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness or connector.
4. CHECK KEY SWITCH GROUND CIRCUIT
Check continuity between key switch harness connector M47 terminal 2 and ground.
Key switch
Continuity
Connector Terminal Ground
M47 2 Yes
Is the inspection result normal?
YES >> Replace key switch.
NO >> Repair or replace harness or connector.
Component Inspection INFOID:0000000010438793
WCS-50
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
A
DOES NOT SOUND
Description INFOID:0000000010438795
B
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking C
brake applied.
Diagnosis Procedure INFOID:0000000010438796
D
1. CHECK PARKING BRAKE WARNING LAMP
1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake. E
Check the parking brake switch signal circuit. Refer to WCS-46, "Diagnosis Procedure".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3. CHECK PARKING BRAKE SWITCH UNIT J
Check the parking brake switch. Refer to PB-65, "DTC Description".
Is the inspection result normal?
K
YES >> Replace the combination meter. Refer to MWI-80, "Removal and Installation".
NO >> Replace the parking brake switch. Refer to PB-146, "Removal and Installation".
WCS
WCS-51
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
< SYMPTOM DIAGNOSIS >
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description INFOID:0000000010438797
• Seat belt warning does not sound even though driver seat belt is not fastened.
• Seat belt warning sounds even though driver seat belt is fastened.
Diagnosis Procedure INFOID:0000000010438798
WCS-52
THE LIGHT REMINDER WARNING DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
A
Description INFOID:0000000010438799
Light reminder warning does not sound even though headlamp is illuminated. B
Diagnosis Procedure INFOID:0000000010438800
WCS
WCS-53
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
Description INFOID:0000000010438801
The key warning chime does not sound, when all of the following conditions are fulfilled:
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in OFF position (ignition switch signal OFF).
• Driver side door is open (front door switch LH ON)
Diagnosis Procedure INFOID:0000000010438802
WCS-54