Professional Documents
Culture Documents
SECTION
BODY CONTROL SYSTEM
BCS B
E
CONTENTS
LHD DOOR LOCK ..............................................................18 F
DOOR LOCK : CONSULT Function (BCM -
PRECAUTION ............................................... 5 DOOR LOCK) (With Intelligent Key) ........................19
DOOR LOCK : CONSULT Function (BCM - G
PRECAUTIONS ................................................... 5 DOOR LOCK) (Without Intelligent Key) ...................20
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- REAR WINDOW DEFOGGER ...................................21
SIONER" ................................................................... 5 REAR WINDOW DEFOGGER : CONSULT Func- H
Precautions for Removing of Battery Terminal ......... 5 tion (BCM - REAR DEFOGGER) .............................21
BCS-1
COMB SW : CONSULT Function (BCM - COMB U1010 CONTROL UNIT (CAN) ......................... 72
SW) ......................................................................... 31 DTC Description ...................................................... 72
Diagnosis Procedure ............................................... 72
BCM ........................................................................... 32
BCM : CONSULT Function (BCM - BCM) .............. 32 POWER SUPPLY AND GROUND CIRCUIT ..... 73
Diagnosis Procedure ............................................... 73
IMMU ......................................................................... 32
IMMU : CONSULT Function (BCM - IMMU) (With COMBINATION SWITCH OUTPUT CIRCUIT ... 74
Intelligent Key) ........................................................ 32 Diagnosis Procedure ............................................... 74
IMMU : CONSULT Function (BCM - IMMU) (With-
out Intelligent Key) .................................................. 32 COMBINATION SWITCH INPUT CIRCUIT ....... 75
Diagnosis Procedure ............................................... 75
BATTERY SAVER .................................................... 32
BATTERY SAVER : CONSULT Function (BCM - COMBINATION SWITCH .................................. 77
BATTERY SAVER) ................................................. 32 Diagnosis Procedure ............................................... 77
TRUNK ...................................................................... 34 SYMPTOM DIAGNOSIS ............................ 78
TRUNK : CONSULT Function (BCM - TRUNK)
(With Intelligent Key) .............................................. 34 COMBINATION SWITCH SYSTEM SYMP-
TRUNK : CONSULT Function (BCM - TRUNK) TOMS ................................................................. 78
(Without Intelligent Key) ......................................... 34 Symptom Table ....................................................... 78
SIGNAL BUFFER ...................................................... 35 REMOVAL AND INSTALLATION .............. 79
SIGNAL BUFFER : CONSULT Function (BCM -
SIGNAL BUFFER) .................................................. 35 BCM (BODY CONTROL MODULE) .................. 79
Removal and Installation ......................................... 79
PANIC ALARM .......................................................... 35
RHD
PANIC ALARM : CONSULT Function (BCM -
PANIC ALARM) (With Intelligent Key) .................... 35 PRECAUTION ............................................ 80
PANIC ALARM : CONSULT Function (BCM -
PANIC ALARM) (Without Intelligent Key) ............... 35 PRECAUTIONS ................................................. 80
Precaution for Supplemental Restraint System
ECU DIAGNOSIS INFORMATION .............. 36 (SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................. 80
BCM (BODY CONTROL MODULE) .................. 36
Precautions for Removing of Battery Terminal ....... 80
Reference Value ..................................................... 36
Fail-safe .................................................................. 55 SYSTEM DESCRIPTION ........................... 81
DTC Inspection Priority Chart .............................. 55
DTC Index .............................................................. 56 COMPONENT PARTS ....................................... 81
WIRING DIAGRAM ..................................... 57 BODY CONTROL SYSTEM ...................................... 81
BODY CONTROL SYSTEM : Component Parts
BCM ................................................................... 57 Location .................................................................. 81
Wiring Diagram ....................................................... 57
POWER CONSUMPTION CONTROL SYSTEM ....... 81
BASIC INSPECTION ................................... 68 POWER CONSUMPTION CONTROL SYSTEM :
Component Parts Location ..................................... 82
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ................................................ 68 SYSTEM ............................................................ 83
Description .............................................................. 68
BODY CONTROL SYSTEM ...................................... 83
Work Procedure ...................................................... 68
BODY CONTROL SYSTEM : System Description... 83
CONFIGURATION (BCM) ................................. 69 BODY CONTROL SYSTEM : Fail-safe ................... 84
Description .............................................................. 69
COMBINATION SWITCH READING SYSTEM ......... 84
Work Procedure ...................................................... 69
COMBINATION SWITCH READING SYSTEM :
Configuration list ..................................................... 70
System Description ................................................. 85
DTC/CIRCUIT DIAGNOSIS ......................... 71 SIGNAL BUFFER SYSTEM ...................................... 88
U1000 CAN COMM ............................................ 71 SIGNAL BUFFER SYSTEM : System Description... 88
DTC Description ..................................................... 71 POWER CONSUMPTION CONTROL SYSTEM ....... 88
Diagnosis Procedure .............................................. 71
BCS-2
POWER CONSUMPTION CONTROL SYSTEM : BATTERY SAVER : CONSULT Function (BCM -
System Description ................................................. 89 BATTERY SAVER) ................................................ 105 A
DIAGNOSIS SYSTEM (BCM) ............................91 TRUNK ..................................................................... 106
TRUNK : CONSULT Function (BCM - TRUNK)
COMMON ITEM ......................................................... 91 (With Intelligent Key) ............................................. 106 B
COMMON ITEM : CONSULT Function (BCM - TRUNK : CONSULT Function (BCM - TRUNK)
COMMON ITEM) (RHD Models) ............................. 91 (Without Intelligent Key) ........................................ 107
DOOR LOCK ............................................................. 91 C
THEFT ALM ............................................................. 107
DOOR LOCK : CONSULT Function (BCM - THEFT ALM : CONSULT Function (BCM -
DOOR LOCK) (With Intelligent Key) ....................... 92 THEFT) .................................................................. 107
DOOR LOCK : CONSULT Function (BCM - D
DOOR LOCK) (Without Intelligent Key) .................. 93 SIGNAL BUFFER .................................................... 108
SIGNAL BUFFER : CONSULT Function (BCM -
REAR WINDOW DEFOGGER ................................... 94 SIGNAL BUFFER) ................................................. 108 E
REAR WINDOW DEFOGGER : CONSULT Func-
tion (BCM - REAR DEFOGGER) ............................ 94 PANIC ALARM ........................................................ 108
PANIC ALARM : CONSULT Function (BCM -
BUZZER ..................................................................... 94 PANIC ALARM) (With Intelligent Key) ................... 108 F
BUZZER : CONSULT Function (BCM - BUZZER) PANIC ALARM : CONSULT Function (BCM -
(With Intelligent Key) ............................................... 95 PANIC ALARM) (Without Intelligent Key) .............. 109
BUZZER : CONSULT Function (BCM - BUZZER)
G
(Without Intelligent Key) .......................................... 95 ECU DIAGNOSIS INFORMATION ............ 110
INT LAMP .................................................................. 96 BCM (BODY CONTROL MODULE) ............... 110
INT LAMP : CONSULT Function (BCM - INT Reference Value .................................................... 110 H
LAMP) ..................................................................... 96 Fail-safe ................................................................. 122
DTC Inspection Priority Chart ............................. 123
MULTI REMOTE ENT ................................................ 98
DTC Index ............................................................. 123 I
MULTI REMOTE ENT : CONSULT Function
(BCM - MULTI REMOTE ENT) ............................... 98 WIRING DIAGRAM .................................... 125
HEADLAMP ............................................................... 99 BCM ................................................................. 125 J
HEADLAMP : CONSULT Function (BCM - HEAD
Wiring Diagram ...................................................... 125
LAMP) (RHD Models) ............................................. 99
BCS-3
COMBINATION SWITCH OUTPUT CIRCUIT . 143 COMBINATION SWITCH SYSTEM SYMP-
Diagnosis Procedure .............................................143 TOMS ................................................................ 148
Symptom Table ..................................................... 148
COMBINATION SWITCH INPUT CIRCUIT ..... 145
Diagnosis Procedure .............................................145 REMOVAL AND INSTALLATION ............. 149
COMBINATION SWITCH ................................ 147 BCM (BODY CONTROL MODULE) ................. 149
Diagnosis Procedure .............................................147 Removal and Installation ....................................... 149
SYMPTOM DIAGNOSIS ............................ 148
BCS-4
PRECAUTIONS
< PRECAUTION > [LHD]
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000008846240
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions for Removing of Battery Terminal INFOID:0000000009888616
• When removing the 12V battery terminal, turn OFF the ignition switch and wait at least 30 seconds. K
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
L
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon- BCS
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
N
The removal of 12V battery may cause a DTC detection error.
BCS-5
COMPONENT PARTS
< SYSTEM DESCRIPTION > [LHD]
SYSTEM DESCRIPTION
COMPONENT PARTS
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM : Component Parts Location INFOID:0000000008846241
JMMIA1336ZZ
BCM
Behind of glove box assembly
BCS-6
COMPONENT PARTS
< SYSTEM DESCRIPTION > [LHD]
POWER CONSUMPTION CONTROL SYSTEM : Component Parts Location
INFOID:0000000008846242 A
JMMIA1337ZZ
L
BCM Intelligent Key unit (with Inrelligent IPDM E/R
Refer to BCS-6, "BODY CONTROL Key system) Refer to PCS-3, "Component Parts
SYSTEM : Component Parts Loca- Refer to DLK-21, Location". BCS
tion". "Component Parts Location".
Combination meter
N
BCS-7
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
SYSTEM
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM : System Description INFOID:0000000008846243
OUTLINE
• BCM (Body Control Module) controls various electrical components.It receives the information required from
CAN communication and the signals received from each switch and sensor.
• BCM has a combination switch reading function for reading the status of combination switches (light, turn
signal, wiper and washer) in addition to functions for controlling the operation of various electrical compo-
nents. It also has a signal transmission function, for other systems, and a power consumption control func-
tion that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with a diagnosis function that operates with CONSULT and allows for various settings to
be changed.
BCM FUNCTION LIST
BCS-8
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
System Reference page
A
DLK-222, "REMOTE KEYLESS ENTRY SYSTEM : System De-
Remote keyless entry system
scription"
• SEC-16, "NISSAN ANTI-THEFT SYSTEM : System Descrip-
tion" (With Intelligent Key system) B
Nissan anti-theft system
• SEC-79, "NISSAN ANTI-THEFT SYSTEM : System Descrip-
tion" (Without Intelligent Key system)
SYSTEM DIAGRAM
O
BCS-9
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
With Rear Wiper
JMMIA1327GB
NOTE:
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
Without Rear Wiper
JMMIA1326GB
NOTE:
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM has a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX
BCS-10
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
Combination Switch Circuit (with Rear Wiper)
A
JMMIA1329GB F
NOTE:
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
Combination switch INPUT-OUTPUT system list G
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1 H
INPUT 3 INT VOLUME 1 RR WASHER — HEADLAMP 2 HI BEAM
INPUT 4 RR WIPER INT INT VOLUME 3 AUTO LIGHT — TAIL LAMP
I
INPUT 5 INT VOLUME 2 RR WIPER ON RR FOG FR FOG —
NOTE:
Headlamp has a dual system switch. J
Combination Switch Circuit (Without Rear Wiper)
BCS
JMMIA1328GB
NOTE: P
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions.
Combination switch INPUT-OUTPUT system list
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 1 — FR WASHER FR WIPER LOW TURN LH TURN RH
INPUT 2 FR WIPER HI — FR WIPER INT PASSING HEADLAMP 1
INPUT 3 INT VOLUME 1 — — HEADLAMP 2 HI BEAM
BCS-11
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
System OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5
INPUT 4 — INT VOLUME 3 — — TAIL LAMP
INPUT 5 INT VOLUME 2 — RR FOG FR FOG —
NOTE:
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION
• BCM reads the status of the combination switch at 10 ms interval normally.
JPMIA0067GB
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption control mode.
• BCM operates as follows and judges the status of the combination switch.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 1 → 2 → 3 → 4 → 5, and outputs
voltage waveform.
- The voltage waveform of INPUT corresponding to the formed circuit is input into the interface on OUTPUT
side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
JPMIA0068GB
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TURN RH switch) is turned ON
• The circuit between OUTPUT 5 and INPUT 1 is formed when the TURN RH switch is turned ON.
BCS-12
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
With Rear Wiper
A
JMMIA1331GB F
Without Rear Wiper
JMMIA1330GB
• BCM detects the combination switch status signal “1E” when the signal of OUTPUT 5 is input to INPUT 1.
• BCM judges that the TURN RH switch is ON when the signal “1E” is detected. L
Example 2: When some switches (TURN RH switch, FR WIPER LOW switch) are turned ON
• The circuits between OUTPUT 5 and INPUT 1 and between OUTPUT 3 and INPUT 1 are formed when the
BCS
TURN RH switch and FR WIPWE LOW switch are turned ON.
BCS-13
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
With Rear Wiper
JMMIA1333GB
JMMIA1332GB
• BCM detects the combination switch status signal “1CE” when the signals of OUTPUT 3 and OUTPUT 5 are
input to INPUT 1.
• BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal “1CE” is
detected.
WIPER INTERMITTENT DIAL POSITION
BCM judges the wiper intermittent dial 1 - 7 by the status of INT INTERMITTENT 1, 2 and 3 switches.
BCS-14
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
SIGNAL BUFFER SYSTEM
A
SIGNAL BUFFER SYSTEM : System Description INFOID:0000000008846246
SYSTEM DIAGRAM B
G
JMMIA1334GB
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit. H
BCS-15
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
POWER CONSUMPTION CONTROL SYSTEM : System Description INFOID:0000000008846247
SYSTEM DIAGRAM
JMMIA1299GB
OUTLINE
• BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status.
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units
- Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
- CAN transmission is stopped
- Control with BCM only is operating
Low power consumption mode (BCM sleep)
- Low power consumption control is active
- CAN transmission is stopped
LOW POWER CONSUMPTION CONTROL WITH BCM
BCM reduces the power consumption with the following operation in the low power consumption mode.
• The reading interval of the each switches changes from 10 ms interval to 60 ms interval.
Sleep mode activation
• BCM receives the sleep-ready signal (ready) from IPDM E/R, combination meter and Intelligent Key unit via
CAN communication.
• BCM transmits the sleep wake up signal (sleep) to each unit when all of the sleep conditions are fulfilled.
• Each unit stops the transmission of CAN communication with the sleep wake up signal. BCM is in CAN com-
munication sleep mode.
• BCM is in the low power consumption mode and perform the low power consumption control when all of the
sleep conditions are fulfilled.
BCS-16
SYSTEM
< SYSTEM DESCRIPTION > [LHD]
Sleep condition
Sleep condition A
• Receiving the sleep-ready signal (ready) from all units
• Ignition switch OFF
• Panic alarm function: Not operation
B
• Warning chime: Not operation
• Stop lamp switch: OFF
• Turn signal indicator lamp: Not operation
• Exterior lamp: OFF C
• Door lock status: No change
• CONSULT communication status: Not communication
• Door switch status: No change
• Driver door lock status: No change D
• Key switch status: No change
• Nissan anti-theft system (NATS)*1: Not operation
• Intelligent Key system buzzer*2: Not operation E
NOTE:
*1: With NATS
*2: With Intelligent Key system F
Wake-up operation
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established,
and then goes into normal mode from low power consumption mode. G
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mit wake up signals to BCM with CAN communication to convey the start of CAN communication.
Wake-up condition H
Wake-up condition
• Receiving the sleep-ready signal (Not-ready) from any units
• Ignition switch: OFF → ACC, ON I
• Key switch: OFF → ON, ON → OFF
• Hazard switch: ON
• PASSING switch: OFF → ON
• TAIL LAMP switch: OFF → ON J
• FR FOG switch: OFF → ON
• RR FOG switch: OFF → ON
• TURN RH: OFF → ON
• TURN LH: OFF → ON K
• Driver door switch: OFF → ON, ON → OFF
• Passenger door switch: OFF → ON, ON → OFF
• Rear RH door switch: OFF → ON, ON → OFF
• Rear LH door switch: OFF → ON, ON → OFF L
• Back door switch: OFF → ON, ON → OFF
• Stop lamp switch: ON
• Door lock and unlock switch: NEUTRAL → LOCK, NEUTRAL → UNLOCK
BCS
• Front door lock assembly (driver side) (unlock sensor): OFF → ON, ON → OFF
BCS-17
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) (LHD Models)
INFOID:0000000008846248
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Manual A/C AIR CONDITONER × ×
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door TRUNK ×
— THEFT ALM* × × ×
— RETAINED PWR* × ×
Signal buffer system SIGNAL BUFFER × ×
Panic alarm PANIC ALARM ×
BCS-18
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (With Intelligent Key)
INFOID:0000000008952694 A
DATA MONITOR
NOTE: B
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
C
Monitor Item Contents
IGN ON SW Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW Indicates [On/Off] condition of key switch D
CDL LOCK SW Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW Indicated [On/Off] condition of unlock signal from door lock unlock switch
E
• [On]: All door lock/unlock with door lock konb and door key cylinder operation
UNLOCK WITH DR
• [Off]: All door lock/unlock without door lock konb and door key cylinder operation
• [On]: Without air bag interlock unlcok function
UNLK SHOK
• [Off]: With air bag interlock unlock function F
DOOR SW-DR Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS Indicated [On/Off] condition of front door switch (passenger side)
G
DOOR SW-RR Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW Indicated [On/Off] condition of back door switch H
LOCK STATUS Indicated [On/Off] condition of unlock sensor
I-KEY LOCK Indicated [On/Off] condition of Intelligent Key lock button
I
I-KEY UNLOCK Indicated [On/Off] condition of Intelligent Key unlock button
Indicated [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sensor unit
• NOMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagnosis sensor
SHOCK SENSOR unit.) J
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
PUSH SW
Indicates [On/Off] condition of ignition knob switch signal from Intelligent Key unit via CAN communi- K
cation
• [On]: With vehicle speed sensing auto door lock function
LOCK WITH SPEED
• [Off]: Without vehicle speed sensing auto door lock function L
VEHICLE SPEED Display the vehicle speed signal received from combination meter by numerical value [Km/h]
ACTIVE TEST
BCS
Test item Description
This test is able to check door lock/unlock operation
N
DOOR LOCK • The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL ULK” on CONSULT screen is touched
WORK SUPPORT O
BCS-19
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Monitor item Description
Automatic door lock unlock function unlock operation mode can be selected from the following
in this mode
AUTO UNLOCK TYPE
• MODE 1: All doors are unlocked
• MODE 2: All doors are unlocked
Automatic door lock unlock function unlock operation mode can be selected from the following
AUTOMATIC DOOR UNLOCK in this mode
SELECT • MODE 1: [IGN OFF interlock door unlock] mode
• MODE 2: [Key out interlock door unlock] mode
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Without Intelligent Key)
INFOID:0000000008952697
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
WORK SUPPORT
BCS-20
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
DATA MONITOR
NOTE: G
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
J
Test Item Description
REAR DEFOGGER Rear window defogger operates when On on CONSULT screen is touched.
K
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER) (With Intelligent Key) INFOID:0000000008952710
L
APPLICATION ITEMS
BCS
Test item Diagnosis mode Description
Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them. N
DATA MONITOR
NOTE:
O
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Display item P
Description
[Unit]
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
KEY ON SW
Status of key switch judged by BCM.
[On/Off]
BCS-21
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Display item
Description
[Unit]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
APPLICATION ITEMS
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Display item
Description
[Unit]
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
KEY ON SW
Status of key switch judged by BCM.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[km/h]
REVERSE SW CAN
This item is displayed, but cannot be monitored.
[On/Off]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
ACTIVE TEST
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
INT LAMP
BCS-22
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
INT LAMP : CONSULT Function (BCM - INT LAMP) INFOID:0000000008952706
A
WORK SUPPORT
JPLIA0093GB F
MODE 1*1 Interior room lamp timer activates with synchronizing all doors.
R LAMP TIMER LOGIC SET
O
Interior room lamp timer activates with synchronizing the driver door
MODE 2
only.
BCS-23
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Monitor item
Description
[Unit]
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
[On/Off]
KEY ON SW
Indicated [On/Off] condition of key switch
[On/Off]
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
[On/Off]
DOOR SW- RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
BACK DOOR SW
Indicated [On/Off] condition of back door switch
[On/Off]
LOCK STATUS
Indicated [On/Off] condition of driver door UNLOCK status
[On/Off]
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
[On/Off]
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of Intelligent Key lock button
[On/Off]
I-KEY UNLOCK
Indicated [On/Off] condition of Intelligent Key unlock button
[On/Off]
KEYLESS LOCK
Indicated [On/Off] condition of keyfob lock button
[On/Off]
KEYLESS UNLOCK
Indicated [On/Off] condition of keyfob unlock button
[On/Off]
PUSH SW
Indicated [On/Off] condition of ignition knob switch
[On/Off]
TRNK/HAT MNTR NOTE:
[On/Off] This item is displayed, but cannot be used
KEY CYL LK-SW
Indicates [On/Off] condition of lock signal from door key cylinder.
[On/Off]
KEY CYL UN-SW
Indicates [On/Off] condition of unlock signal from door key cylinder.
[On/Off]
I-KEY DR UNLK
Indicated [On/Off] condition of driver door unlock status
[On/Off]
ACC ON SW
Indicates [On/Off] condition of ignition switch ACC position
[On/Off]
ACTIVE TEST
DATA MONITOR
BCS-24
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable A
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
I
Test item Description
This test is able to check door lock/unlock operation
DOOR LOCK • ALL LCK: The all door lock actuators are locked J
• ALL ULK:The all door lock actuators are unlocked
This test is able to check interior room lamp operation
INT LAMP • On: Operate K
• Off: Non-operation
NOTE:
TRUNK/GLASS HATCH
This item is displayed, but cannot be used L
FLASHER This test is able to check flasher operation [LH/RH/Off]
BCS-25
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Test item Description
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
PANIC ALARM SET
• MODE1: 0.5 sec
• MODE2: Non-operation
NOTE:
TRUNK OPEN SET
This item is displayed, but cannot be used
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (LHD Models) INFOID:0000000008952704
WORK SUPPORT
Monitor item
Description
[Unit]
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
[On/Off]
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
[On/Off]
KEY ON SW
Indicated [On/Off] condition of key switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
TURN SIGNAL L
[On/Off]
BCS-26
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Monitor item
Description
[Unit] A
HI BEAM SW
[On/Off]
HEAD LAMP SW1 B
[On/Off]
HEAD LAMP SW2
[On/Off] C
TAIL LAMP SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
AUTO LIGHT SW D
[On/Off]
PASSING SW
[On/Off] E
FR FOG SW
[On/Off]
RR FOG SW F
[On/Off]
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
G
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR H
Indicated [On/Off] condition of rear door switch RH
[On/Off]
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
I
BACK DOOR SW
Indicated [On/Off] condition of back door switch
[On/Off]
KEYLESS LOCK J
Indicated [On/Off] condition of keyfob lock button
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of Intelligent Key lock button
[On/Off]
K
PKB SW The parking brake switch status received from combination meter with CAN commu-
[On/Off] nication
PUSH SW
Indicated [On/Off] condition of ignition knob switch L
[On/Off]
OPTICAL SENSOR
The value of outside brightness voltage input from the optical sensor
[V]
BCS
OPTI SEN (DTCT) NOTE:
[V] This item is displayed, but cannot be monitored
OPTI SEN (FILT) NOTE:
[V] This item is displayed, but cannot be monitored N
LIG SEN COND NOTE:
[On/Off/NG] This item is displayed, but cannot be monitored
O
ENGINE RUN
The engine status received from ECM using CAN communication.
[On/Off]
VEHICLE SPEED Display the vehicle speed signal received from combination meter by numerical value
[km/h] [Km/h] P
ACTIVE TEST
BCS-27
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
RH
NOTE:
CORNERING LAMP LH
This item is displayed, but cannot be tested.
Off
WIPER
WIPER : CONSULT Function (BCM - WIPER) INFOID:0000000008952708
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Description
[Unit]
IGN ON SW
Ignition switch ON status judged from ignition power supply.
[Off/On]
IGN SW CAN
Ignition switch ON status received from IPDM E/R with CAN communication.
[Off/On]
FR WIPER HI
[Off/On]
FR WIPER LOW
[Off/On]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER INT
[Off/On]
FR WASHER SW
[Off/On]
BCS-28
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Monitor Item
Description
[Unit] A
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 3 − 5− 7]
FR WIPER STOP B
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
[Off/On]
RR WIPER ON
[Off/On] C
RR WIPER INT
Each switch status that BCM judges from the combination switch reading function.
[Off/On]
RR WASHER SW D
[Off/On]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor.
[Off/On] E
REVERSE SW CAN NOTE:
[Off/On] The item is indicated, but not monitored.
VEHICLE SPEED F
The value of the vehicle speed signal received from combination meter with CAN communication.
[km/h]
RAIN SENSOR NOTE:
[Off/On] The item is indicated, but not monitored.
G
ACTIVE TEST
FLASHER
L
FLASHER : CONSULT Function (BCM - FLASHER) (LHD Models) INFOID:0000000008952705
ACTIVE TEST
BCS-29
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Manual A/C)
INFOID:0000000008952693
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Display item list
Monitor Item [Unit] Contents
IGN SW [On/Off] Displays ignition switch position status as judged form ignition switch signal.
FAN ON SIG [On/Off] Displays blower motor status as judged from blower fan ON signal.
AIR COND SW [On/Off] Displays A/C switch status as judged from A/C switch signal.
THERMO AMP [On/Off] Displays thermo control amp. status as judged from thermo control amp. signal.
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) INFOID:0000000008952695
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BCS-30
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
COMB SW
E
COMB SW : CONSULT Function (BCM - COMB SW) INFOID:0000000008846258
DATA MONITOR
NOTE: F
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
G
Monitor item [UNIT] Description
TURN SIGNAL R Displays the status of TURN RH switch in combination switch judged by the combination switch reading func-
[Off/On] tion. H
TURN SIGNAL L Displays the status of the TURN LH switch in combination switch judged by the combination switch reading
[Off/On] function.
HI BEAM SW Displays the status of HI BEAM switch in combination switch judged by the combination switch reading func- I
[Off/On] tion.
HEAD LAMP SW 1 Displays the status of HEADLAMP 1 switch in combination switch judged by the combination switch reading
[Off/On] function. J
HEAD LAMP SW 2 Displays the status of HEADLAMP 2 switch in combination switch judged by the combination switch reading
[Off/On] function.
TAIL LAMP SW Displays the status of TAIL LAMP switch in combination switch judged by the combination switch reading K
[Off/On] function.
PASSING SW Displays the status of PASSING switch in combination switch judged by the combination switch reading func-
[Off/On] tion. L
AUTO LIGHT SW Displays the status of AUTO LIGHT switch in combination switch judged by the combination switch reading
[Off/On] function.
FR FOG SW Displays the status of FR FOG switch in combination switch judged by the combination switch reading func- BCS
[Off/On] tion.
RR FOG SW Displays the status of RR FOG switch in combination switch judged by the combination switch reading func-
[Off/On] tion.
N
FR WIPER HI Displays the status of FR WIPER HI switch in combination switch judged by the combination switch reading
[Off/On] function.
FR WIPER LOW Displays the status of FR WIPER LOW switch in combination switch judged by the combination switch read- O
[Off/On] ing function.
FR WIPER INT Displays the status of FR WIPER INT switch in combination switch judged by the combination switch reading
[Off/On] function.
P
FR WASHER SW Displays the status of FR WASHER switch in combination switch judged by the combination switch reading
[Off/On] function.
INT VOLUME
Displays the status of wiper intermittent dial position judged by the combination switch reading function.
[1 - 7]
RR WIPER ON Displays the status of RR WIPER ON switch in combination switch judged by the combination switch reading
[Off/On] function.
BCS-31
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
Monitor item [UNIT] Description
RR WIPER INT Displays the status of RR WIPER INT switch in combination switch judged by the combination switch reading
[Off/On] function.
RR WASHER SW Displays the status of RR WASHER switch in combination switch judged by the combination switch reading
[Off/On] function.
BCM
BCM : CONSULT Function (BCM - BCM) INFOID:0000000008846259
WORK SUPPORT
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
IMMU
IMMU : CONSULT Function (BCM - IMMU) (With Intelligent Key) INFOID:0000000008952702
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER) INFOID:0000000008952707
WORK SUPPORT
BCS-32
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
*:Factory setting
DATA MONITOR C
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. D
Monitor item
Description
[Unit]
E
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
[On/Off]
KEY ON SW
Indicated [On/Off] condition of key switch F
[On/Off]
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS
G
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH H
[On/Off]
DOOR SW- RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
BACK DOOR SW I
Indicated [On/Off] condition of back door switch
[On/Off]
LOCK STATUS
Indicated [On/Off] condition of driver door UNLOCK status
[On/Off] J
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
[On/Off]
CDL UNLOCK SW K
Indicated [On/Off] condition of unlock signal from door lock unlock switch
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of Intelligent Key lock button
[On/Off] L
I-KEY UNLOCK
Indicated [On/Off] condition of Intelligent Key unlock button
[On/Off]
KEYLESS LOCK BCS
Indicated [On/Off] condition of keyfob lock button
[On/Off]
KEYLESS UNLOCK
Indicated [On/Off] condition of keyfob unlock button
[On/Off] N
PUSH SW
Indicated [On/Off] condition of ignition knob switch
[On/Off]
TRNK/HAT MNTR
Indicates [On/Off] condition of trunk room lamp switch O
[On/Off]
KEY CYL LK-SW
Indicates [On/Off] condition of lock signal from door key cylinder.
[On/Off]
P
KEY CYL UN-SW
Indicates [On/Off] condition of unlock signal from door key cylinder.
[On/Off]
I-KEY DR UNLK
Indicated [On/Off] condition of driver door unlock status
[On/Off]
ACC ON SW
Indicates [On/Off] condition of ignition switch ACC position
[On/Off]
BCS-33
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
ACTIVE TEST
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK) (With Intelligent Key) INFOID:0000000008952696
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BCS-34
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [LHD]
SIGNAL BUFFER
A
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER) INFOID:0000000008846263
DATA MONITOR B
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. C
Monitor item [UNIT] Description
OIL PRESS SW NOTE:
D
[Off/On] This item is indicated, but not monitored.
BRAKE SW
Displays the switch status input from stop lamp switch.
[Off/On]
E
ACTIVE TEST
ACTIVE TEST
I
Test item Description
This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON” on
VEHICLE SECURITY HORN J
CONSULT screen touched
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM) (Without Intelligent Key)
INFOID:0000000008952700
K
ACTIVE TEST
L
Test item Description
This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON” on
VEHICLE SECURITY HORN
CONSULT screen touched
BCS
BCS-35
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
BCS-36
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Monitor Item Condition Value/Status
A
Bright outside of the vehicle Close to 5 V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0 V
Equivalent to speed- B
VEHICLE SPEED While driving
ometer reading
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On C
Lighting switch OFF Off
TAIL LAMP SW
Lighting switch 1ST On
D
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
NOTE: E
TRNK/HAT MNTR Off
The item is indicated, but not monitored.
NOTE:
IKEY TRNK/HAT Off
The item is indicated, but not monitored.
F
PANIC button of Intelligent key is not pressed Off
I-KEY PANIC
PANIC button of Intelligent key is pressed On
KYLS TRNK/HAT
NOTE:
Off
G
The item is indicated, but not monitored.
PANIC button of key fob is not pressed Off
KEYLESS PANIC
PANIC button of key fob is pressed On H
Lighting switch OFF Off
HI BEAM SW
Lighting switch HI On
I
Lighting switch OFF Off
HEAD LAMP SW 1
Lighting switch 2ND On
Lighting switch OFF Off J
HEAD LAMP SW 2
Lighting switch 2ND On
Other than lighting switch AUTO Off
AUTO LIGHT SW K
Lighting switch AUTO On
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On L
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On
Turn signal switch OFF Off
BCS
TURN SIGNAL R
Turn signal switch RH On
Turn signal switch OFF Off N
TURN SIGNAL L
Turn signal switch LH On
Ignition switch OFF or ACC Off
IGN SW CAN
Ignition switch ON On O
Front wiper switch OFF Off
FR WIPER HI
Front wiper switch HI On
P
Front wiper switch OFF Off
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off
FR WIPER INT
Front wiper switch INT On
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
BCS-37
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Monitor Item Condition Value/Status
Rear wiper switch OFF Off
RR WIPER ON
Rear wiper switch ON On
Rear wiper switch OFF Off
RR WIPER INT
Rear wiper switch INT On
Rear washer switch OFF Off
RR WASHER SW
Rear washer switch ON On
Rear wiper stop position Off
RR WIPER STOP
Other than rear wiper stop position On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
Any position other than front wiper stop position Off
FR WIPER STOP
Front wiper stop position On
Hazard switch OFF Off
HAZARD SW
Hazard switch ON On
Blower control dial OFF Off
FAN ON SIG
Other than blower control dial OFF On
A/C switch OFF Off
AIR COND SW
A/C switch ON On
Ignition switch ON Off
THERMO AMP
Evaporator is extremely low temperature On
NOTE:
TRNK OPNR SW Off
The item is indicated, but not monitored.
NOTE:
OIL PRESS SW Off
The item is indicated, but not monitored.
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On
BCS-38
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
TERMINAL LAYOUT
A
L
JMMIA1338ZZ
BCS-39
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Insert mechanical key into ignition key cyl-
9 – 16 V
5 inder
Ground Key switch Input
(LG) Remove mechanical key from ignition key
0V
cylinder
PKID0873E
1.5 V
Lighting switch HI
PKID0877E
1.4 V
Combination
6
Ground
Combination switch
Input switch*1 Lighting switch 2ND
(Y) INPUT 3 (Wiper vol-
ume dial 4)
PKID0875E
1.5 V
PKID0881E
1.4 V
1.5 V
BCS-40
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
Lighting switch HI
F
Combination JPMIA0166GB
H
Lighting switch 2ND
JPMIA0167GB
I
1.3 V
J
Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
K
• Wiper volume dial 2
• Wiper volume dial 3
JPMIA0196GB
1.3 V L
BCS
BCS-41
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
PKID0883E
1.5 V
PKID0887E
1.4 V
Combination
7
Ground
Combination switch
Input switch*1 Lighting switch AUTO
(GR) INPUT 4 (Wiper vol-
ume dial 4)
PKID0885E
1.5 V
1.4 V
PKID0891E
1.4 V
BCS-42
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
E
Combination
7
Ground
Combination switch
Input switch*2 Lighting switch 1ST
(GR) INPUT 4 (Wiper vol-
ume dial 4) F
JPMIA0166GB
1.3 V
G
BCS
BCS-43
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
PKID0893E
1.5 V
PKID0895E
1.4 V
Combination
8
Ground
Combination switch
Input switch*1 Turn signal switch LH
(V) INPUT 1 (Wiper vol-
ume dial 4)
PKID0897E
1.5 V
PKID0899E
1.5 V
PKID0903E
1.6 V
BCS-44
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
F
JPMIA0166GB
1.3 V
G
Combination
H
8
Ground
Combination switch
Input switch*2 Turn signal switch RH
(V) INPUT 1 (Wiper vol-
ume dial 4)
JPMIA0167GB
I
1.3 V
JPMIA0168GB
1.3 V L
BCS
N
JPMIA0196GB
1.3 V
O
BCS-45
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
PKID0905E
1.5 V
PKID0907E
1.4 V
Combination
9
Ground
Combination switch
Input switch*1 Lighting switch PASS
(G) INPUT 2 (Wiper vol-
ume dial 4)
PKID0909E
1.4 V
PKID0911E
1.6 V
PKID0913E
1.6 V
BCS-46
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
F
JPMIA0166GB
1.3 V
G
Combination
H
9
Ground
Combination switch
Input switch*2 Lighting switch PASS
(G) INPUT 2 (Wiper vol-
ume dial 4)
JPMIA0167GB
I
1.3 V
JPMIA0168GB
1.3 V L
BCS
N
JPMIA0196GB
1.3 V
O
BCS-47
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
PKID0915E
1.5 V
PKID0917E
1.5 V
Combination
10
Ground
Combination switch
Input switch*1 Rear fog lamp switch ON
(BR) INPUT 5 (Wiper vol-
ume dial 4)
PKID0917E
1.5 V
PKID0915E
1.5 V
1.5 V
BCS-48
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.3 V D
F
JPMIA0167GB
H
Rear fog lamp switch ON
JPMIA0168GB
I
1.3 V
J
Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2 K
• Wiper volume dial 6
• Wiper volume dial 7
JPMIA0196GB
1.3 V L
LOCK status (Unlock sen-
Front door lock as- 12 V
11 sor switch OFF)
Ground sembly driver side Input Driver door
(R) UNLOCK status (Unlock BCS
(Unlock sensor) 0V
sensor switch ON)
SKIB3419J
BCS-49
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
OFF
13 Back door (When back door closed)
Ground Back door switch Input
(P) switch
SKIB3419J
ON
0V
(When back door opened)
SKIB3419J
ON (When passenger
0V
door opened)
OFF (When driver door
12 V
15 Driver door closed)
Ground Driver door switch Input
(R) switch ON (When driver door
0V
opened)
SKIB3419J
17 OFF 9 – 16 V
Ground A/C indicator Output A/C indicator
(SB) ON 0 – 0.5 V
Rear win- OFF (Not pressed) 5V
20 Rear window defog-
Ground Input dow defog-
(W) ger switch ON (Pressed) 0V
ger switch
21 Input/
Ground CAN-L — —
(P) Output
22 Input/
Ground CAN-H — —
(L) Output
BCS-50
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
ON 0V
B
C
23 Security indicator Security indi- Blinking (Ignition switch
Ground Input
(O) lamp control cator lamp OFF)
D
JPMIA0014GB
11.3 V
OFF 12 V
E
24
Ground Air bag signal Input — —
(V)
F
25*3 Optical sensor pow- Ignition OFF, ACC 0V
Ground Output
(R) er supply switch ON 4.65 - 5.5 V
OFF H
26
Ground Blower fan ON Input Blower fan
(SB)
PKID0924E
I
11.2 V
ON 0V
J
OFF K
27
Ground A/C switch Input A/C switch
(G)
PKID0924E L
11.2 V
ON 0V
33 Hazard OFF 9 – 16 V
Ground Hazard switch Input
(SB) switch ON 0 – 1.5 V
Door lock NEUTRAL position 12 V
34 Door lock and unlock
Ground Input and unlock
(GR) switch LOCK LOCK position 0V
switch
BCS-51
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
All switches OFF
Turn signal switch RH
Combination Lighting switch 2ND
36
Ground
Combination switch
Output switch*1
(LG) OUTPUT 5 Lighting switch HI
(Wiper vol-
ume dial 4)
Lighting switch 1ST PKID0584E
9.0 V
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
36
Ground
Combination switch
Output switch*2 Lighting switch 2ND
(LG) OUTPUT 5 (Wiper vol-
ume dial 4)
Turn signal switch RH
JPMIA0164GB
9.1 V
All switches OFF
Front washer switch ON
9.4 V
Rear wiper switch ON
All switches OFF 0V
Front washer switch ON
Combination
37
Ground
Combination switch
Output switch*2 Any of the conditions be-
(R) OUTPUT 2 (Wiper vol- low with all switches OFF
ume dial 4) • Wiper volume dial 1
• Wiper volume dial 5
• Wiper volume dial 6
JPMIA0161GB
9.1 V
All switches OFF
Front wiper switch LO
Combination Front wiper switch INT
38
Ground
Combination switch
Output switch*1
(W) OUTPUT 3 Lighting switch AUTO
(Wiper vol-
ume dial 4)
Rear fog lamp switch ON PKID0582E
9.6 V
BCS-52
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switches OFF 0V
B
Front wiper switch INT
Front wiper switch LO
Combination
38
Ground
Combination switch
Output switch*2 C
(W) OUTPUT 3 (Wiper vol-
ume dial 4)
Rear fog lamp switch ON
D
JPMIA0162GB
9.3 V
All switches OFF
E
Turn signal switch LH
Combination Lighting switch PASS
39
Ground
Combination switch
Output switch*1
(Y) OUTPUT 4 (Wiper vol-
Lighting switch 2ND F
ume dial 4)
Front fog lamp switch ON PKID0583E
9.7 V G
All switches OFF 0V
Lighting switch 2ND
H
Lighting switch PASS
Combination
39
Ground
Combination switch
Output switch*2
(Y) OUTPUT 4 (Wiper vol- I
ume dial 4)
Turn signal switch LH
JPMIA0163GB
J
9.3 V
All switches OFF
Front wiper switch HI K
Any of the condition below
Combination with all switches OFF
40
Ground
Combination switch
Output switch*1 • Wiper volume dial 1
(P) OUTPUT 1 (Wiper vol- • Wiper volume dial 2
L
ume dial 4) • Wiper volume dial 3
• Wiper volume dial 6
PKID0580E
• Wiper volume dial 7 BCS
9.3 V
Rear wiper switch INT
All switches OFF 0V
Front wiper switch HI N
BCS-53
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
OFF (Brake pedal is not
0V
42 Stop lamp depressed)
Ground Stop lamp switch Input
(R) switch ON (Brake pedal is de-
9 – 16 V
pressed)
45 Ignition
Ground Turn signal RH Output
(W) switch ON Turn signal switch RH
PKID0926E
6.4 V
Turn signal switch OFF 0V
46 Ignition
Ground Turn signal LH Output
(LG) switch ON Turn signal switch LH
PKID0926E
6.4 V
Rear wiper stop position 0V
49*1 Ground
Rear wiper stop po-
Input
Ignition
(SB) sition switch ON Any position other than
rear wiper stop position
PKID0925E
1.6 V
BCS-54
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
58
Ground Ground Output Ignition switch ON 0V B
(B)
60
Ground Power supply (IGN) Output Ignition switch ON 9 – 16 V
(L)
C
*1: With rear wiper models
*2: Without rear wiper models
*3: With auto light system
D
Fail-safe INFOID:0000000008846266
O
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
BCS-55
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [LHD]
Priority DTC
• U1000: CAN COMM
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
2
• B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
×:Applicable
Security indicator
CONSULT display Fail-safe Reference
lamp ON
U1000: CAN COMM — — BCS-71
U1010: CONTROL UNIT (CAN) — — BCS-72
•SEC-49*1
B2190: NATS ANTENNA AMP × ×
•SEC-102*2
•SEC-52*1
B2191: DIFFERENCE OF KEY × ×
•SEC-105*2
•SEC-53*1
B2192: ID DISCORD BCM-ECM × ×
•SEC-106*2
•SEC-54*1
B2193: CHAIN OF BCM-ECM × ×
•SEC-107*2
B2194: DISCORD BCM-I-KEY × × SEC-56
•SEC-57*1
B2195: ANTI SCANNING × ×
•SEC-109*2
NOTE:
• *1: With Intelligent Key system
• *2: Without Intelligent Key system
BCS-56
BCM
< WIRING DIAGRAM > [LHD]
WIRING DIAGRAM A
BCM
Wiring Diagram INFOID:0000000008846269
B
BCS
JRMWE1576GB
BCS-57
BCM
< WIRING DIAGRAM > [LHD]
JRMWE1577GB
BCS-58
BCM
< WIRING DIAGRAM > [LHD]
BCS
JRMWE1578GB
BCS-59
BCM
< WIRING DIAGRAM > [LHD]
JRMWE1579GB
BCS-60
BCM
< WIRING DIAGRAM > [LHD]
BCS
JRMWE1648GB
BCS-61
BCM
< WIRING DIAGRAM > [LHD]
JRMWE1649GB
BCS-62
BCM
< WIRING DIAGRAM > [LHD]
BCS
JRMWE1650GB
BCS-63
BCM
< WIRING DIAGRAM > [LHD]
JRMWE1651GB
BCS-64
BCM
< WIRING DIAGRAM > [LHD]
BCS
JRMWE1652GB
BCS-65
BCM
< WIRING DIAGRAM > [LHD]
JRMWE1653GB
BCS-66
BCM
< WIRING DIAGRAM > [LHD]
BCS
JRMWE1654GB
BCS-67
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
< BASIC INSPECTION > [LHD]
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description INFOID:0000000008846270
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
• When replacing BCM, perform the system initialization (NATS) (if equipped).
• When replacing BCM, perform the keyfob ID registration (if equipped).
Work Procedure INFOID:0000000008846271
>> GO TO 2.
2.REPLACE BCM
Replace BCM. Refer to BCS-79, "Removal and Installation".
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to BCS-69, "Work Procedure".
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM. B
Configuration has three functions as follows.
Function Description
C
• Reads the vehicle configuration of current BCM.
READ CONFIGURATION
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection.
D
WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data.
NOTE:
Manual setting item: Items which need selection by vehicle specifications E
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION: F
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model. G
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
H
Work Procedure INFOID:0000000008846273
BCS-69
CONFIGURATION (BCM)
< BASIC INSPECTION > [LHD]
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
BCS-70
U1000 CAN COMM
< DTC/CIRCUIT DIAGNOSIS > [LHD]
DTC/CIRCUIT DIAGNOSIS A
U1000 CAN COMM
DTC Description INFOID:0000000008846276
B
DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul- C
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less D
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-32, "CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart". E
DTC DETECTION LOGIC
BCS
BCS-71
U1010 CONTROL UNIT (CAN)
< DTC/CIRCUIT DIAGNOSIS > [LHD]
U1010 CONTROL UNIT (CAN)
DTC Description INFOID:0000000008846278
POSSIBLE CAUSE
BCM
FAIL-SAFE
—
Diagnosis Procedure INFOID:0000000008846279
1.REPLACE BCM
When DTC “U1010” is detected, replace BCM.
BCS-72
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [LHD]
POWER SUPPLY AND GROUND CIRCUIT
A
Diagnosis Procedure INFOID:0000000008846280
(+) H
BCM (−) Condition Voltage
Connector Terminal
I
M66 52
OFF
M67 56 Ignition switch posi-
Ground 9 – 16 V
4 tion ACC J
M65
3 ON
Is the measurement value normal?
K
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT L
Check continuity between BCM harness connector and ground.
BCM BCS
Continuity
Connector Terminal Ground
M67 58 Existed
Does continuity exist? N
YES >> INSPECTION END
NO >> Repair harness or connector.
O
BCS-73
COMBINATION SWITCH OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [LHD]
COMBINATION SWITCH OUTPUT CIRCUIT
Diagnosis Procedure INFOID:0000000008846281
BCM
System Continuity
Connector Terminal
OUTPUT 1 40
OUTPUT 2 37 Ground
OUTPUT 3 M65 38 Not existed
OUTPUT 4 39
OUTPUT 5 36
Does continuity exist?
YES >> Repair harnesses or connectors.
NO >> GO TO 3.
3.CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-77, "Diagnosis Procedure".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-79, "Removal and Installation".
NO >> Replace the combination switch (applicable parts). Refer to SR-20, "Removal and Installation".
BCS-74
COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [LHD]
COMBINATION SWITCH INPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000008846282
Terminals
N
(+) (−) Voltage
System
BCM (Approx.)
Connector Terminal O
INPUT 1 8
INPUT 2 9
INPUT 3 6 Ground P
INPUT 4 M65 7
INPUT 5 10 JPMIA0165GB
1.4 V
Is the measurement value normal?
BCS-75
COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [LHD]
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-79, "Removal and Installation".
4.CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-77, "Diagnosis Procedure".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-79, "Removal and Installation".
NO >> Replace combination switch (applicable parts). Refer to SR-20, "Removal and Installation".
BCS-76
COMBINATION SWITCH
< DTC/CIRCUIT DIAGNOSIS > [LHD]
COMBINATION SWITCH
A
Diagnosis Procedure INFOID:0000000008928875
BCS
BCS-77
COMBINATION SWITCH SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [LHD]
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000008846283
HEAD LAMP SW 1
HEAD LAMP SW 2
RR WASHER SW
FR WASHER SW
TURN SIGNAL R
TURN SIGNAL L
FR WIPER LOW
TAIL LAMP SW
RR WIPER INT
RR WIPER ON
FR WIPER INT
PASSING SW
FR WIPER HI
INT VOLUME
HI BEAM SW
RR FOG SW
FR FOG SW
Malfunction
combination
× × × × A
× × × × B
× × × × C
× × × D
× × × × E
× × × F
× × × × G
× × × H
× × × × I
× × × × J
All Items K
If only one item is detected or the item is not applicable to the combinations A to K L
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
Malfunctioning part Repair or replace
combination
A Combination switch INPUT 1 circuit
B Combination switch INPUT 2 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
C Combination switch INPUT 3 circuit
part. Refer to BCS-75, "Diagnosis Procedure".
D Combination switch INPUT 4 circuit
E Combination switch INPUT 5 circuit
F Combination switch OUTPUT 1 circuit
G Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction-
H Combination switch OUTPUT 3 circuit
ing part. Refer to BCS-74, "Diagnosis Procedure".
I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit
K BCM Replace BCM. Refer to BCS-79, "Removal and Installation".
Replace the combination switch. Refer to SR-20, "Removal and Installa-
L Combination switch
tion".
BCS-78
BCM (BODY CONTROL MODULE)
< REMOVAL AND INSTALLATION > [LHD]
REMOVAL
1. Disconnect the battery cable from the negative terminal. D
2. Remove glove box assembly. Refer to IP-13, "Removal and Installation".
3. Remove BCM mounting screws .
E
JMMIA1335ZZ
H
4. Remove BCM and disconnect the connectors.
INSTALLATION
I
Install in the reverse order of removal.
CAUTION:
Be sure to perform “WRITE CONFIGURATION” when replacing BCM. Or not doing so, BCM control
function does not operate normally. Refer to BCS-69, "Work Procedure". J
NOTE:
• Be sure to perform the system initialization (NATS) when replacing BCM (if equipped).
• Be sure to perform the keyfob ID registration when replacing BCM (if equipped). Refer to DLK-243, "Work K
Procedure".
BCS
BCS-79
PRECAUTIONS
< PRECAUTION > [RHD]
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000009809733
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal INFOID:0000000009888619
• When removing the 12V battery terminal, turn OFF the ignition switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition switch is turned OFF. If the battery terminal
is removed before ECU stops, then a DTC detection error or ECU data corruption may occur.
• For vehicles with the 2-batteries, be sure to connect the main battery and the sub battery before turning ON
the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of main battery and sub battery discon-
nected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
BCS-80
COMPONENT PARTS
< SYSTEM DESCRIPTION > [RHD]
SYSTEM DESCRIPTION A
COMPONENT PARTS
BODY CONTROL SYSTEM
B
BODY CONTROL SYSTEM : Component Parts Location INFOID:0000000009809734
BCS
JMMIA1486ZZ
BCM N
Behind of glove box assembly
BCS-81
COMPONENT PARTS
< SYSTEM DESCRIPTION > [RHD]
POWER CONSUMPTION CONTROL SYSTEM : Component Parts Location
INFOID:0000000009809735
JMMIA1487ZZ
BCS-82
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
SYSTEM
A
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM : System Description INFOID:0000000009809736
B
OUTLINE
• BCM (Body Control Module) controls various electrical components.It receives the information required from
CAN communication and the signals received from each switch and sensor. C
• BCM has a combination switch reading function for reading the status of combination switches (light, turn
signal, wiper and washer) in addition to functions for controlling the operation of various electrical compo-
nents. It also has a signal transmission function, for other systems, and a power consumption control func- D
tion that reduces the power consumption with the ignition switch OFF.
• BCM is equipped with a diagnosis function that operates with CONSULT and allows for various settings to
be changed.
E
BCM FUNCTION LIST
System Reference
F
BCS-85, "COMBINATION SWITCH READING SYSTEM : System
Combination switch reading system
Description"
Signal buffer system BCS-88, "SIGNAL BUFFER SYSTEM : System Description" G
BCS-89, "POWER CONSUMPTION CONTROL SYSTEM : System
Power consumption control system
Description"
Headlamp system EXL-14, "HEADLAMP SYSTEM : System Description" H
EXL-19, "TURN SIGNAL AND HAZARD WARNING LAMP SYS-
Turn signal and hazard warning lamp system
TEM : System Description"
EXL-22, "PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : I
Parking, license plate and tail lamps system
System Description"
Front fog lamp system EXL-25, "FRONT FOG LAMP SYSTEM : System Description"
EXL-30, "EXTERIOR LAMP BATTERY SAVER SYSTEM : System J
Exterior lamp battery saver system
Description"
INL-9, "INTERIOR ROOM LAMP CONTROL SYSTEM : System De-
Interior room lamp control system
scription" K
INL-13, "INTERIOR ROOM LAMP BATTERY SAVER SYSTEM :
Interior room lamp battery saver system
System Description"
INL-18, "ILLUMINATION CONTROL SYSTEM : System Descrip- L
Illumination control system
tion"
WW-7, "FRONT WIPER AND WASHER SYSTEM : System De-
Front wiper and washer system
scription" BCS
WW-12, "REAR WIPER AND WASHER SYSTEM : System Descrip-
Rear wiper and washer system
tion"
Rear window defogger system DEF-34, "System Description" N
Warning chime system WCS-7, "WARNING CHIME SYSTEM : System Description"
Manual cooling system HAC-59, "System Description"
O
• DLK-345, "System Description" (With Intelligent Key system)
Power door lock system • DLK-541, "POWER DOOR LOCK SYSTEM : System Description"
(Without Intelligent Key system)
Intelligent Key system/engine start system DLK-348, "INTELLIGENT KEY SYSTEM : System Description" P
DLK-544, "REMOTE KEYLESS ENTRY SYSTEM : System De-
Remote keyless entry system
scription"
Nissan Anti-Theft System SEC-127, "NISSAN ANTI-THEFT SYSTEM : System Description"
BCS-83
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
System Reference
Theft warning alarm • SEC-130, "VEHICLE SECURITY SYSTEM : System Description"
(With Intelligent Key system)
Vehicle security system
Panic alarm • SEC-196, "VEHICLE SECURITY SYSTEM : System Description"
(Without Intelligent Key system)
Power window system PWC-6, "System Description"
FAIL-SAFE INDEX
BCM performs fail-safe control when any DTC listed below is detected.
BCS-84
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
COMBINATION SWITCH READING SYSTEM : System Description INFOID:0000000009809738
A
SYSTEM DIAGRAM
JMMIA1216GB
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions. G
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch. H
• BCM has a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a
maximum of 20 switch status.
COMBINATION SWITCH MATRIX I
BCS
JMMIA1217GB
*: TAIL LAMP switch links lighting switch 1ST and 2ND positions. O
BCS-85
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
Headlamp has a dual system switch.
COMBINATION SWITCH READING FUNCTION
Description
• BCM reads the status of the combination switch at 10 ms interval normally.
JPMIA0609GB
NOTE:
BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power con-
sumption control mode.
• BCM operates as follows and judges the status of the combination switch.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 1 → 2 → 3 → 4 → 5, and outputs
voltage waveform.
- The voltage waveform of OUTPUT corresponding to the formed circuit is input into the interface on INPUT
side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
JMMIA0326GB
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TAIL LAMP switch) is turned ON
BCS-86
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
• The circuit between OUTPUT 4 and INPUT 5 is formed when the TAIL LAMP switch is turned ON.
A
JMMIA1300GB F
• BCM detects the combination switch status signal “5D” when the signal of OUTPUT 4 is input to INPUT 5.
• BCM judges that the TAIL LAMP switch is ON when the signal “5D” is detected.
Example 2: When some switches (TURN RH switch, TAIL LAMP switch) are turned ON G
• The circuits between OUTPUT 1 and INPUT 5 and between OUTPUT 4 and INPUT 5 are formed when the
TURN RH switch and TAIL LAMP switch are turned ON.
H
JMMIA1301GB
BCS
• BCM detects the combination switch status signal “5AD” when the signals of OUTPUT 1 and OUTPUT 4 are
input to INPUT 5.
• BCM judges that the TURN RH switch and TAIL LAMP switch are ON when the signal “5AD” is detected.
N
WIPER INTERMITTENT DIAL POSITION
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2 and 3 switches.
Switch status
O
Wiper intermittent dial position
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
1 ON ON ON
P
2 ON ON OFF
3 ON OFF OFF
4 OFF OFF OFF
5 OFF OFF ON
BCS-87
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
Switch status
Wiper intermittent dial position
INT VOLUME 1 INT VOLUME 2 INT VOLUME 3
6 OFF ON ON
7 OFF ON OFF
NOTE:
For details of wiper intermittent dial position, refer to WW-7, "FRONT WIPER AND WASHER SYSTEM : Sys-
tem Description".
SIGNAL BUFFER SYSTEM
SIGNAL BUFFER SYSTEM : System Description INFOID:0000000009809740
SYSTEM DIAGRAM
JMMIA1280GB
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
SIGNAL TRANSMISSION FUNCTION LIST
BCS-88
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
POWER CONSUMPTION CONTROL SYSTEM : System Description INFOID:0000000009809742
A
SYSTEM DIAGRAM
JMMIA1299GB F
OUTLINE
• BCM incorporates a power consumption control function that reduces the power consumption according to
the vehicle status. G
• BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R, combination meter and Intelligent Key unit) that operates with the ignition
switch OFF. H
BCS-89
SYSTEM
< SYSTEM DESCRIPTION > [RHD]
Sleep condition
CAN sleep condition BCM sleep condition
• Receiving the sleep-ready signal (ready) from all units
• Key switch status: No change
• Ignition switch: OFF
• Theft warning alarm: Not operation
• Panic alarm: Not operation
• Warning chime: Not operation • Interior room lamp battery saver: Time out
• Stop lamp switch: OFF • Nissan anti-theft system (NATS): Not operation
• Turn signal indicator lamp: Not operation • Remote keyless entry receiver communication status: No com-
• Exterior lamp: OFF munication
• Door lock status: No change
• CONSULT communication status: Not communication
• Door switch status: No change
• Driver door lock status: No change
• Key switch status: No change
WAKE-UP OPERATION
• BCM transmits sleep wake up signal (wake up) to each unit when any condition listed below is established,
and then goes into normal mode from low power consumption mode.
• Each unit starts transmissions with CAN communication by receiving sleep wake up signals. Each unit trans-
mits wake up signals to BCM with CAN communication to convey the start of CAN communication.
Wake-up condition
Wake-up condition
• Receiving the sleep-ready signal (Not-ready) from any units
• Ignition switch: OFF→ ACC, ON
• Key switch: OFF→ ON, ON → OFF
• Hazard switch: ON
• HI BEAM switch: OFF → ON, ON → OFF
• PASSING switch: OFF → ON, ON → OFF
• HEADLAMP 1 switch: OFF → ON, ON → OFF
• HEADLAMP 2 switch: OFF → ON, ON → OFF
• TAIL LAMP switch: OFF → ON
• FR FOG switch: OFF → ON, ON → OFF
• TURN RH switch: OFF → ON
• TURN LH switch: OFF → ON
• Driver door switch: OFF → ON, ON → OFF
• Passenger door switch: OFF → ON, ON → OFF
• Rear RH door switch: OFF → ON, ON → OFF
• Rear LH door switch: OFF → ON, ON → OFF
• Back door switch: OFF → ON, ON → OFF
• Stop lamp switch: ON
• Door lock and unlock switch: NEUTRAL → LOCK, NEUTRAL → UNLOCK
• Door key cylinder switch (driver side): NEUTRAL → LOCK, NEUTRAL → UNLOCK
• Remote keyless entry receiver communication: Receiving
• Front door lock assembly (driver side) (unlock sensor): OFF → ON, ON → OFF
BCS-90
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) (RHD Models)
INFOID:0000000009809743 B
APPLICATION ITEM
CONSULT can display each diagnostic item using the diagnostic test modes shown following. C
BCS-91
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (With Intelligent Key)
INFOID:0000000009809831
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
WORK SUPPORT
BCS-92
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK) (Without Intelligent Key)
INFOID:0000000009809834
H
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable I
to this vehicle, refer to CONSULT display items.
BCS-93
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor Item Contents
Indicates [On/Off] condition of ignition knob switch signal from Intelligent Key unit via CAN communi-
PUSH SW
cation
VEHICLE SPEED Display the vehicle speed signal received from combination meter by numerical value [Km/h]
ACTIVE TEST
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BUZZER
BCS-94
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
BUZZER : CONSULT Function (BCM - BUZZER) (With Intelligent Key) INFOID:0000000009809838
A
APPLICATION ITEMS
Display item
Description E
[Unit]
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
F
KEY ON SW
Status of key switch judged by BCM.
[On/Off]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function. G
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
H
ACTIVE TEST
Display item I
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off). J
K
APPLICATION ITEMS
Display item
Description
[Unit] O
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
KEY ON SW P
Status of key switch judged by BCM.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[km/h]
REVERSE SW CAN
This item is displayed, but cannot be monitored.
[On/Off]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
BCS-95
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
ACTIVE TEST
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP) INFOID:0000000009816132
WORK SUPPORT
JPLIA0093GB
MODE 1*1 Interior room lamp timer activates with synchronizing all doors.
R LAMP TIMER LOGIC SET Interior room lamp timer activates with synchronizing the driver door
MODE 2
only.
BCS-96
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
*1: Factory setting for LHD models and RHD models
*2: Factory setting for LHD models A
*3: Factory setting for RHD models
DATA MONITOR B
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
C
Monitor item
Description
[Unit]
IGN ON SW D
Indicated [On/Off] condition of ignition switch in ON position
[On/Off]
KEY ON SW
Indicated [On/Off] condition of key switch
[On/Off] E
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS F
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
[On/Off] G
DOOR SW- RL
Indicated [On/Off] condition of rear door switch LH
[On/Off]
BACK DOOR SW H
Indicated [On/Off] condition of back door switch
[On/Off]
LOCK STATUS
Indicated [On/Off] condition of driver door UNLOCK status
[On/Off] I
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
[On/Off]
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
J
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of Intelligent Key lock button
[On/Off] K
I-KEY UNLOCK
Indicated [On/Off] condition of Intelligent Key unlock button
[On/Off]
KEYLESS LOCK L
Indicated [On/Off] condition of keyfob lock button
[On/Off]
KEYLESS UNLOCK
Indicated [On/Off] condition of keyfob unlock button
[On/Off]
BCS
PUSH SW
Indicated [On/Off] condition of ignition knob switch
[On/Off]
TRNK/HAT MNTR NOTE: N
[On/Off] This item is displayed, but cannot be used
KEY CYL LK-SW
Indicates [On/Off] condition of lock signal from door key cylinder.
[On/Off]
O
KEY CYL UN-SW
Indicates [On/Off] condition of unlock signal from door key cylinder.
[On/Off]
I-KEY DR UNLK
[On/Off]
Indicated [On/Off] condition of driver door unlock status P
ACC ON SW
Indicates [On/Off] condition of ignition switch ACC position
[On/Off]
ACTIVE TEST
BCS-97
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
WORK SUPPORT
BCS-98
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
NOTE:
HORN CHIRP SET
This item is displayed, but cannot be used
C
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
HAZARD LAMP SET • MODE2: Unlock operation only
• MODE3: Lock operation only D
• MODE4: Lock and unlock operation
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
E
PANIC ALARM SET • MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec
Auto door lock time can be changed in this mode F
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1minute
AUTO LOCK SET G
• MODE 4: 2minute
• MODE 5: 3minute
• MODE 6: 4minute
• MODE 7: 4minute H
NOTE:
TRUNK OPEN SET
This item is displayed, but cannot be used
HEADLAMP I
J
WORK SUPPORT
Monitor item
Description
[Unit] O
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
[On/Off]
ACC ON SW P
Indicated [On/Off] condition of ignition switch in ACC position
[On/Off]
BCS-99
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor item
Description
[Unit]
HI BEAM SW
[On/Off]
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
TAIL LAMP SW
[On/Off]
PASSING SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
AUTO LIGHT SW NOTE:
[On/Off] This item is displayed, but cannot be monitored
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
[On/Off]
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
[On/Off]
DOOR SW-RR
Indicated [On/Off] condition of slide door switch RH
[On/Off]
DOOR SW-RL
Indicated [On/Off] condition of slide door switch LH
[On/Off]
BACK DOOR SW
Indicated [On/Off] condition of back door switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
TURN SIGNAL L
[On/Off]
KEY ON SW
Indicated [On/Off] condition of key switch
[On/Off]
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from keyfob
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of lock signal from Intelligent Key
[On/Off]
PKB SW The parking brake switch status received from combination meter with CAN commu-
[On/Off] nication
ENGINE RUN
The engine status received from ECM using CAN communication.
[On/Off]
VEHICLE SPEED Display the vehicle speed signal received from combination meter by numerical value
[km/h] [Km/h]
PUSH SW
Indicated [On/Off] condition of ignition knob switch
[On/Off]
OPTI SEN (DTCT) NOTE:
[V] This item is displayed, but cannot be monitored
OPTI SEN (FILT) NOTE:
[V] This item is displayed, but cannot be monitored
PUSH SW
Indicates [On/Off] condition of ignition knob switch
[On/Off]
ACTIVE TEST
BCS-100
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
WIPER F
G
WORK SUPPORT
DATA MONITOR J
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. K
Monitor Item
Description
[Unit]
L
IGN ON SW
Ignition switch ON status judged from ignition power supply.
[Off/On]
IGN SW CAN
Ignition switch ON status received from IPDM E/R with CAN communication. BCS
[Off/On]
FR WIPER HI
[Off/On]
N
FR WIPER LOW
[Off/On]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER INT
[Off/On] O
FR WASHER SW
[Off/On]
P
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 3 − 5− 7]
FR WIPER STOP
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
[Off/On]
BCS-101
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor Item
Description
[Unit]
RR WIPER ON
[Off/On]
RR WIPER INT
Each switch status that BCM judges from the combination switch reading function.
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor.
[Off/On]
REVERSE SW CAN NOTE:
[Off/On] The item is indicated, but not monitored.
VEHICLE SPEED
The value of the vehicle speed signal received from combination meter with CAN communication.
[km/h]
RAIN SENSOR NOTE:
[Off/On] The item is indicated, but not monitored.
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (RHD Models) INFOID:0000000009826003
WORK SUPPORT
Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
BCS-102
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor item
Description
[Unit] A
TURN SIGNAL R
[On/Off]
Each switch condition that BCM judges from the combination switch reading function
TURN SIGNAL L B
[On/Off]
ACTIVE TEST
C
Test item Operation Description
RH Outputs the voltage to turn the right side turn signal lamps.
D
FLASHER LH Outputs the voltage to turn the left side turn signal lamps.
Off Stops the voltage to turn the turn signal lamps OFF.
AIR CONDITIONER E
F
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable G
to this vehicle, refer to CONSULT display items.
INTELLIGENT KEY
K
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY) INFOID:0000000009809832
DATA MONITOR L
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. BCS
COMB SW
BCS-103
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
COMB SW : CONSULT Function (BCM - COMB SW) INFOID:0000000009809751
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
BCM
BCM : CONSULT Function (BCM - BCM) INFOID:0000000009809752
WORK SUPPORT
Item Description
RESET SETTING VALUE Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
BCS-104
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
IMMU
A
IMMU : CONSULT Function (BCM - IMMU) (With Intelligent Key) INFOID:0000000009809836
DATA MONITOR B
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. C
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
D
KEY ON SW Indicates [ON/OFF] condition of key switch.
PUSH SW Indicates [ON/OFF] condition of ignition knob switch.
E
ACTIVE TEST
BATTERY SAVER G
H
WORK SUPPORT
BCS-105
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor item
Description
[Unit]
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
[On/Off]
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
[On/Off]
I-KEY LOCK
Indicated [On/Off] condition of Intelligent Key lock button
[On/Off]
I-KEY UNLOCK
Indicated [On/Off] condition of Intelligent Key unlock button
[On/Off]
KEYLESS LOCK
Indicated [On/Off] condition of keyfob lock button
[On/Off]
KEYLESS UNLOCK
Indicated [On/Off] condition of keyfob unlock button
[On/Off]
PUSH SW
Indicated [On/Off] condition of ignition knob switch
[On/Off]
TRNK/HAT MNTR
Indicates [On/Off] condition of trunk room lamp switch
[On/Off]
KEY CYL LK-SW
Indicates [On/Off] condition of lock signal from door key cylinder.
[On/Off]
KEY CYL UN-SW
Indicates [On/Off] condition of unlock signal from door key cylinder.
[On/Off]
I-KEY DR UNLK
Indicated [On/Off] condition of driver door unlock status
[On/Off]
ACC ON SW
Indicates [On/Off] condition of ignition switch ACC position
[On/Off]
ACTIVE TEST
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK) (With Intelligent Key) INFOID:0000000009809833
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
BCS-106
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitor Item Contents
A
Indicates [On/Off] condition of ignition knob switch signal from Intelligent Key unit via CAN com-
PUSH SW
munication
VEHICLE SPEED Indicates [Km/h] condition of vehicle speed signal from combination meter
B
TRUNK : CONSULT Function (BCM - TRUNK) (Without Intelligent Key) INFOID:0000000009809835
DATA MONITOR C
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items. D
TRNK OPNR SW
NOTE: F
This item is displayed, but cannot be monitored
LOCK STATUS Indicates [On/Off] condition of unlock sensor
IGN ON SW Indicated [On/Off] condition of ignition switch in ON position G
VEHICLE SPEED Indicates [Km/h] condition of vehicle speed signal from combination meter
THEFT ALM H
THEFT ALM : CONSULT Function (BCM - THEFT) INFOID:0000000009809837
I
WORK SUPPORT
DATA MONITOR
NOTE: L
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
BCS
Monitored Item Description
REQ SW -DR Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS Indicates [ON/OFF] condition of door request switch (passenger side). N
NOTE:
REQ SW -RR
This is displayed even when it is not equipped.
NOTE: O
REQ SW -RL
This is displayed even when it is not equipped.
REQ SW -BD/TR Indicates [ON/OFF] condition of back door request switch.
PUSH SW Indicates [ON/OFF] condition of push-button ignition switch P
UNLK SEN -DR Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BCS-107
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
Monitored Item Description
DOOR SW-BK Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from door key cylinder.
TR/BD OPEN SW Indicates [ON/OFF] condition of back door opener switch.
NOTE:
TRNK/HAT MNTR
This is displayed even when it is not equipped.
RKE-LOCK Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
NOTE:
RKE-TR/BD
This is displayed even when it is not equipped.
ACTIVE TEST
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER) INFOID:0000000009809756
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM) (With Intelligent Key)
INFOID:0000000009809827
ACTIVE TEST
BCS-108
DIAGNOSIS SYSTEM (BCM)
< SYSTEM DESCRIPTION > [RHD]
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM) (Without Intelligent Key) C
INFOID:0000000009809829
ACTIVE TEST
D
Test item Description
This test is able to check horn operation. Horn is activated for 0.5 seconds after “ON” on
VEHICLE SECURITY HORN E
CONSULT screen touched
Transmits the high beam request signal via CAN communication to turn the head lamp
HEAD LAMP (HI)
(HI)
F
BCS
BCS-109
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
BCS-110
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Monitor Item Condition Value/Status
A
NOTE:
TRNK/HAT MNTR Off
The item is indicated, but not monitored.
Other than driver door key cylinder LOCK position Off
KEY CYL LK-SW B
Driver door key cylinder LOCK position On
Other than driver door key cylinder UNLOCK position Off
KEY CYL UN-SW
Driver door key cylinder UNLOCK position On C
NOTE:
I-KEY DR UNLK Off
The item is indicated, but not monitored.
Ignition switch OFF Off D
ACC ON SW
Ignition switch ACC or ON On
Shift selector in any position other than reverse Off
REVERSE SW CAN E
Shift selector in reverse position On
Lighting switch OFF Off
TAIL LAMP SW
Lighting switch 1ST On F
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
NOTE:
G
BUCKLE SW Off
The item is indicated, but not monitored.
Equivalent to speed-
VEHICLE SPEED While driving H
ometer reading
Ignition switch OFF or ACC Off
IGN SW CAN
Ignition switch ON On
I
Front wiper switch OFF Off
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off J
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off
FR WIPER INT K
Front wiper switch INT On
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On L
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
Any position other than front wiper stop position Off
FR WIPER STOP BCS
Front wiper stop position On
Rear wiper switch OFF Off
RR WIPER ON
Rear wiper switch ON On N
Rear wiper switch OFF Off
RR WIPER INT
Rear wiper switch INT On
Rear washer switch OFF Off O
RR WASHER SW
Rear washer switch ON On
Rear wiper stop position Off
RR WIPER STOP P
Other than rear wiper stop position On
NOTE:
RAIN SENSOR Off
The item is indicated, but not monitored.
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
BCS-111
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Monitor Item Condition Value/Status
NOTE:
SHOCK SENSOR NORMAL
The item is indicated, but not monitored.
NOTE:
KYLS TRNK/HAT Off
The item is indicated, but not monitored.
PANIC button of keyfob is not pressed Off
KEYLESS PANIC
PANIC button of keyfob is pressed On
Lighting switch OFF Off
HI BEAM SW
Lighting switch HI On
Lighting switch OFF Off
HEAD LAMP SW 1
Lighting switch 2ND On
Lighting switch OFF Off
HEAD LAMP SW 2
Lighting switch 2ND On
NOTE:
AUTO LIGHT SW Off
The item is indicated, but not monitored.
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
NOTE:
RR FOG SW Off
The item is indicated, but not monitored.
Parking brake switch is OFF Off
PKB SW
Parking brake switch is ON On
Engine stopped Off
ENGINE RUN
Engine running On
NOTE:
OPTI SEN (DTCT) 0V
The item is indicated, but not monitored.
NOTE:
OPTI SEN (FILT) 0V
The item is indicated, but not monitored.
NOTE:
LIG SEN COND OFF
The item is indicated, but not monitored.
Blower fan OFF Off
FAN ON SIG
Blower fan ON On
Compressor OFF Off
AIR COND SW
Compressor ON On
NOTE:
THERMO AMP Off
The item is indicated, but not monitored.
NOTE:
FR DEF SW Off
The item is indicated, but not monitored.
NOTE:
IKEY TRNK/HAT Off
The item is indicated, but not monitored.
NOTE:
TRNK OPNR SW Off
The item is indicated, but not monitored.
NOTE:
OIL PRESS SW Off
The item is indicated, but not monitored.
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On
BCS-112
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
TERMINAL LAYOUT
A
L
JMMIA1065ZZ
BCS-113
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
JPMIA0342JP
2.0 V
All switches OFF 0V
Turn signal switch LH
Lighting switch PASS
PKIB4956J
0.8 V
All switches OFF 0V
Front wiper switch LO
Combination Front wiper switch MIST
4 Combination switch switch
Ground Input
(L) INPUT 3 (Wiper intermit-
tent dial 4)
Front wiper switch INT
PKIB4958J
1.0 V
BCS-114
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switches OFF
0V B
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4)
Rear washer switch ON C
(Wiper intermittent dial 4)
Any of the condition below
with all switches OFF D
• Wiper intermittent dial 1
5 Combination switch Combination • Wiper intermittent dial 5 PKIB4958J
Ground Input
(G) INPUT 2 switch • Wiper intermittent dial 6 1.0 V
E
F
Rear wiper switch ON
(Wiper intermittent dial 4)
G
PKIB4956J
0.8 V
All switches OFF
0V H
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
I
Rear wiper switch INT
(Wiper intermittent dial 4)
J
Wiper intermittent dial 3
(All switches OFF) PKIB4958J
1.0 V
K
1.9 V
PKIB4956J
0.8 V P
BCS-115
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
PKIB4960J
7.0 - 8.0 V
UNLOCK position 0V
PKIB4960J
7.0 - 8.0 V
LOCK position 0V
OFF (Brake pedal is not
0V
9 Stop lamp depressed)
Ground Stop lamp switch Input
(R) switch ON (Brake pedal is de-
9 – 16 V
pressed)
JPMIA0012GB
1.0 - 1.5 V
Pressed 0V
OFF
(When passenger door
12 Passenger door Passenger door closed)
Ground Input
(BR) switch switch
PKIB4960J
7.0 - 8.0 V
ON
(When passenger door 0V
opened)
BCS-116
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
OFF
(When rear RH door C
13 Rear RH door closed)
Ground Rear RH door switch Input
(Y) switch
PKIB4960J
7.0 - 8.0 V D
ON
(When rear RH door 0V
opened) E
18
Ground Receiver ground Input Ignition switch ON 0V
(V)
Insert mechanical key into F
0V
ignition key cylinder
Remove mechanical key
from ignition key cylinder 5V G
(Any door opened)
Remote keyless en-
19 Ignition switch
Ground try receiver power Input
(BR) OFF H
supply
Remove mechanical key
from ignition key cylinder
(Any door closed)
I
JPMIA0338JP
Waiting
L
Remote keyless en-
20 Ignition switch
Ground try receiver commu- Input
(G) OFF PIIB7728J
nication
BCS
Signal receiving N
PIIB7729J O
21 Input/ Just after inserting ignition key in key cylinder Pointer of tester should move
Ground NATS antenna amp.
(P) Output Other than above 0V
P
BCS-117
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
ON 0V
JPMIA0590GB
11.3 V
OFF 12 V
25 Input/ Just after inserting ignition key in key cylinder Pointer of tester should move
Ground NATS antenna amp.
(LG) Output Other than above 0V
27 OFF
Ground Compressor ON Input Compressor
(BR)
PIIB7730J
1.5 - 2.0 V
ON 0V
OFF 0V
28 Blower fan
Ground Blower fan ON Input
(SB) switch Except OFF
PKIB4960J
6.5 - 7.0 V
29 OFF 9 – 16 V
Ground Hazard switch Input Hazard switch
(P) ON 0 – 1.5 V
PKIB4960J
7.0 - 8.0 V
32 Combination switch Combination
Ground Output Front fog lamp switch ON
(LG) OUTPUT 5 switch
(Wiper intermittent dial 4)
Rear wiper switch ON
(Wiper intermittent dial 4)
Any of the condition below
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2 PKIB4956J
• Wiper intermittent dial 6 1.0 V
• Wiper intermittent dial 7
BCS-118
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
PKIB4960J
7.0 - 8.0 V D
33 Combination switch Combination
Ground Output
(P) OUTPUT 4 switch Lighting switch 1ST
(Wiper intermittent dial 4)
Rear wiper switch INT
E
(Wiper intermittent dial 4)
Any of the condition below
with all switches OFF F
• Wiper intermittent dial 1
• Wiper intermittent dial 5 PKIB4958J
H
All switches OFF
(Wiper intermittent dial 4)
I
PKIB4960J
7.0 - 8.0 V
N
All switches OFF
O
Combination PKIB4960J
1.2 V
BCS-119
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Combination PKIB4960J
1.2 V
Insert mechanical key into ignition key cylin-
37 9 – 16 V
der
(LG)*1 Ground Key switch Input
Remove mechanical key from ignition key
(GR)*2 0V
cylinder
OFF
43 Back door (When back door closed)
Ground Back door switch Input
(P) switch
PKIB4960J
7.0 - 8.0 V
ON
0V
(When back door opened)
Rear wiper stop position 0V
PKID0925E
1.6 V
BCS-120
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0012GB
1.0 - 1.5 V D
LOCK position 0V
JPMIA0012GB
1.0 - 1.5 V G
UNLOCK position 0V
OFF
I
(When driver door closed)
47 Driver door
Ground Driver door switch Input
(SB) switch
PKIB4960J
J
7.0 - 8.0 V
ON
(When driver door 0V
opened) K
L
OFF
(When rear LH door
48 Rear LH door closed)
Ground Rear LH door switch Input BCS
(W) switch
PKIB4960J
7.0 - 8.0 V
ON N
(When rear LH door 0V
opened)
Rear room lamp OFF 9 – 16 V O
49 Rear room lamp
Ground Output (Switch is in
(BR) control ON 0–1V
DOOR position)
BCS-121
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Turn signal switch OFF 0V
60 Ignition switch
Ground Turn signal LH Output
(LG) ON Turn signal switch LH
PKIC6370E
6.5 V
(Turn signal lamp turn on: 9 – 16
V)
Turn signal switch OFF 0V
61 Ignition switch
Ground Turn signal RH Output
(W) ON Turn signal switch RH
PKIC6370E
6.5 V
(Turn signal lamp turn on: 9 – 16
V)
Interior room OFF 9 – 16 V
63 Interior room lamp lamp (Switch is
Ground Output
(BR) control in DOOR posi- ON 0–1V
tion)
LOCK (Actuator is activat-
9 – 16 V
65 ed)
Ground All doors LOCK Output All doors
(GR) Other then LOCK (Actua-
0V
tor is not activated)
UNLOCK (Actuator is acti-
9 – 16 V
66 vated)
Ground All doors UNLOCK Output All doors
(G) Other then UNLOCK (Ac-
0V
tuator is not activated)
67
Ground Ground Output Ignition switch ON 0V
(B)
68 P/W power supply
Ground Output Ignition switch ON 9 – 16 V
(L) (IGN)
69 P/W power supply
Ground Output Ignition switch OFF 9 – 16 V
(P) (BAT)
70 Battery power sup-
Ground Input Ignition switch OFF 9 – 16 V
(Y) ply
*1: With Intelligent Key
*2: Without Intelligent Key
Fail-safe INFOID:0000000009809758
FAIL-SAFE INDEX
BCM performs fail-safe control when any DTC listed below is detected.
BCS-122
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Priority DTC
• U1000: CAN COMM K
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY L
• B2192: ID DISCORD BCM-ECM
2
• B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING BCS
N
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again. O
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch P
OFF → ON after returning to the normal condition if the malfunction is detected again.
BCS-123
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION > [RHD]
Security indicator lamp
DTC Fail-safe Reference
ON
U1010: CONTROL UNIT (CAN) × — BCS-141
B2190: NATS ANTENNA AMP × × SEC-163
B2191: DIFFERENCE OF KEY × × SEC-166
B2192: ID DISCORD BCM-ECM × × SEC-167
B2193: CHAIN OF BCM-ECM × × SEC-168
B2194: DISCORD BCM-I-KEY × × SEC-170
B2195: ANTI SCANNING × × SEC-171
BCS-124
BCM
< WIRING DIAGRAM > [RHD]
WIRING DIAGRAM A
BCM
Wiring Diagram INFOID:0000000009809761
B
BCS
JRMWE1580GB
BCS-125
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1581GB
BCS-126
BCM
< WIRING DIAGRAM > [RHD]
BCS
JRMWE1582GB
BCS-127
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1583GB
BCS-128
BCM
< WIRING DIAGRAM > [RHD]
BCS
JRMWE1655GB
BCS-129
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1656GB
BCS-130
BCM
< WIRING DIAGRAM > [RHD]
BCS
JRMWE1657GB
BCS-131
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1658GB
BCS-132
BCM
< WIRING DIAGRAM > [RHD]
BCS
JRMWE1659GB
BCS-133
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1660GB
BCS-134
BCM
< WIRING DIAGRAM > [RHD]
BCS
JRMWE1661GB
BCS-135
BCM
< WIRING DIAGRAM > [RHD]
JRMWE1662GB
BCS-136
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
< BASIC INSPECTION > [RHD]
BASIC INSPECTION A
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description INFOID:0000000009809762
B
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace- C
ment.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM. D
AFTER REPLACEMENT
CAUTION:
E
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model. F
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
• When replacing BCM, perform the system initialization (NATS) (if equipped).
G
• When replacing BCM, perform the keyfob ID registration (if equipped).
Work Procedure INFOID:0000000009809763
H
1.SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to BCS-138, "Descrip- I
tion".
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after J
replacing BCM.
>> GO TO 2. K
2.REPLACE BCM
Replace BCM. Refer to BCS-149, "Removal and Installation".
L
>> GO TO 3.
3.WRITING VEHICLE SPECIFICATION BCS
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to BCS-138, "Work Procedure". N
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
Function Description
• Reads the vehicle configuration of current BCM.
READ CONFIGURATION
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Manual selection Writes the vehicle configuration with manual selection.
WRITE CONFIGURATION - Config file Writes the vehicle configuration with saved data.
NOTE:
Manual setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting can not be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
Work Procedure INFOID:0000000009809765
BCS-138
CONFIGURATION (BCM)
< BASIC INSPECTION > [RHD]
>> GO TO 4.
4.OPERATION CHECK A
SETTING ITEM
NOTE
Items Setting value E
• WITHOUT: Without air bag
UNLOCK WITH SHOCK WITHOUT ⇔ WITH
• WITH: With air bag
• MODE4: CVT models F
CAN CONNECTION UNIT MODE4 ⇔ WITHOUT
• WITHOUT: A/T or M/T models
• WITH: Without Intelligent Key
KYELESS ENTRY WITH ⇔ WITHOUT
• WITHOUT: With Intelligent Key
G
• WITH: With air bag
AUTO LOCK&UNLOCK FUNC WITH ⇔ WITHOUT
• WITHOUT: Without air bag
⇔: Items which confirm vehicle specifications H
BCS
BCS-139
U1000 CAN COMM
< DTC/CIRCUIT DIAGNOSIS > [RHD]
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM
DTC Description INFOID:0000000009809768
DESCRIPTION
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to LAN-32, "CAN COMMUNICATION SYSTEM : CAN Communica-
tion Signal Chart".
DTC DETECTION LOGIC
POSSIBLE CAUSE
CAN communication system
FAIL-SAFE
—
Diagnosis Procedure INFOID:0000000009809769
BCS-140
U1010 CONTROL UNIT (CAN)
< DTC/CIRCUIT DIAGNOSIS > [RHD]
U1010 CONTROL UNIT (CAN)
A
DTC Description INFOID:0000000009809770
POSSIBLE CAUSE
D
BCM
FAIL-SAFE
— E
Diagnosis Procedure INFOID:0000000009809771
1.REPLACE BCM F
When DTC “U1010” is detected, replace BCM.
G
>> Replace BCM. Refer to BCS-149, "Removal and Installation".
BCS
BCS-141
POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [RHD]
POWER SUPPLY AND GROUND CIRCUIT
BCM
BCM : Diagnosis Procedure INFOID:0000000009809772
Terminals
Ignition switch position
(+)
BCM (−)
OFF ACC ON
Connector Terminal
70 Battery Battery Battery
M73
57 voltage voltage voltage
BCM
Continuity
Connector Terminal Ground
M73 67 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
BCS-142
COMBINATION SWITCH OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [RHD]
COMBINATION SWITCH OUTPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000009809773
BCM
System Continuity
Connector Terminal I
OUTPUT 1 36
OUTPUT 2 35 Ground
J
OUTPUT 3 M71 34 Not existed
OUTPUT 4 33
OUTPUT 5 32 K
Does continuity exist?
YES >> Repair harnesses or connectors.
NO >> GO TO 3. L
Terminals N
(+) (−) Voltage
System
BCM (Approx.)
O
Connector Terminal
OUTPUT 1 36
OUTPUT 2 35 P
OUTPUT 3 34 Ground
OUTPUT 4 M71 33
OUTPUT 5 32 PKIB4960J
7.0 - 7.5 V
Is the measurement value normal?
BCS-143
COMBINATION SWITCH OUTPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [RHD]
YES >> GO TO 4.
NO >> Replace BCM. Refer to BCS-149, "Removal and Installation".
4.CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-147, "Diagnosis Procedure".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-149, "Removal and Installation".
NO >> Replace the combination switch (applicable parts).
BCS-144
COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [RHD]
COMBINATION SWITCH INPUT CIRCUIT
A
Diagnosis Procedure INFOID:0000000009809774
BCM
System Continuity
Connector Terminal I
INPUT 1 6
INPUT 2 5 Ground
J
INPUT 3 M71 4 Not existed
INPUT 4 3
INPUT 5 2 K
Does continuity exist?
YES >> Repair harnesses or connectors.
NO >> GO TO 3. L
BCS-145
COMBINATION SWITCH INPUT CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [RHD]
No >> GO TO 4.
4.CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-147, "Diagnosis Procedure".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-149, "Removal and Installation".
NO >> Replace combination switch (applicable parts).
BCS-146
COMBINATION SWITCH
< DTC/CIRCUIT DIAGNOSIS > [RHD]
COMBINATION SWITCH
A
Diagnosis Procedure INFOID:0000000009809775
BCS
BCS-147
COMBINATION SWITCH SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [RHD]
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table INFOID:0000000009809776
HEAD LAMP SW 2
RR WASHER SW
FR WASHER SW
TURN SIGNAL R
TURN SIGNAL L
FR WIPER LOW
TAIL LAMP SW
RR WIPER INT
RR WIPER ON
FR WIPER INT
PASSING SW
FR WIPER HI
INT VOLUME
HI BEAM SW
FR FOG SW
Malfunction
combination
× × × × A
× × × × B
× × × × C
× × × D
× × × E
× × × F
× × × × G
× × H
× × × × I
× × × × J
All items K
If only one item is detected or the item is not applicable to the combinations A to K L
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
Malfunctioning part Repair or replace
combination
A Combination switch OUTPUT 1 circuit
B Combination switch OUTPUT 2 circuit
Inspect the combination switch output circuit applicable to the malfunction-
C Combination switch OUTPUT 3 circuit
ing part. Refer to BCS-143, "Diagnosis Procedure".
D Combination switch OUTPUT 4 circuit
E Combination switch OUTPUT 5 circuit
F Combination switch INPUT 1 circuit
G Combination switch INPUT 2 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
H Combination switch INPUT 3 circuit
part. Refer to BCS-145, "Diagnosis Procedure".
I Combination switch INPUT 4 circuit
J Combination switch INPUT 5 circuit
K BCM Replace BCM. Refer to BCS-149, "Removal and Installation".
L Combination switch Inspect the combination switch. Refer to BCS-147, "Diagnosis Procedure".
BCS-148
BCM (BODY CONTROL MODULE)
< REMOVAL AND INSTALLATION > [RHD]
REMOVAL
1. Disconnect the battery cable from the negative terminal. D
2. Remove glove box assembly. Refer to IP-13, "Removal and Installation".
3. Disconnect connector then pull down BCM from the steering
member. E
JMMIA1488ZZ
H
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to perform “WRITE CONFIGURATION” when replacing BCM. Or not doing so, BCM control I
function does not operate normally. Refer to BCS-138, "Work Procedure".
NOTE:
• Be sure to perform the system initialization (NATS) when replacing BCM (if equipped). J
• Be sure to perform the keyfob ID registration when replacing BCM (if equipped). Refer to DLK-565, "Work
Procedure".
K
BCS
BCS-149