Professional Documents
Culture Documents
The documentation is only complete when used in combination with the relevant
documentation for the sensor.
1 Product features 3
2 Technical data 4
3 Installation 8
4 Electrical connections 14
5 Notes 23
Highlights
• Control unit for 4…20 mA/HART® field devices
• 2 wire, loop-powered device
• Second 4…20 mA current output for any HART® variable
• 2 configurable relays for status output, limit switch, system alarm, cleaning control, error
current or alert functionality acc. to USP<645>
• Different user-configurable measuring pages for all 4…20 mA and HART® signals, trend
graph and summary page
• Commissioning of OPTIBAR pressure transmitters and OPTIWAVE level transmitters
• Full access to all sensor functions including calibration possible by connecting a HART®
handheld
• Status signalisation by 5 LEDs according to NAMUR NE 107
• Robust plastic or aluminium housing (IP66/67)
Measuring system
Measuring principle The measuring principle depends on the used field device(s), for further information
refer to the field device manual(s).
Measuring range The measuring range depends on the used field device(s), for further information
refer to the field device manual(s).
Design
Construction A typical measuring system consists of:
• SHD 200
• HART® capable field device
• Field device cable
Communication protocol HART® 5
Operating conditions
Temperature
Ambient -20...+70°C / -4...+158°F
Note: the manufacturer strongly recommends to protect the unit from external heat
sources such as direct sunlight as higher temperatures reduce the life cycle of all
electronic components!
Storage -30...+70°C / -22...+158°F
Altitude 2000 m / 6561.68 f
Other conditions
Humidity RH4...100% rH
(IEC 60721-3-4:1995 Class 4K4)
Ingress protection IP66/ IP67
acc. to IEC 60529:
Installation conditions
Weight Approx. 413 g / 0.91 lb for plastic housing
Approx. 855 g / 1.89 lb for aluminium housing
Installation Wall mounting; assure a vertical mounting orientation
Wall or pipe mounting with weather protection cover
Materials
Housing Aluminium
Plastic (Polycarbonate)
Cable glands 3xM16x1.5
2xM12x1.5
Material: Polyamid
Electrical connections
Power supply 20...30 VDC, loop powered from 4...20 mA signal input; Voltage drop max. 4V at 4 mA
and 2V at 20 mA
System requirements 250 loop resistance for HART® communication.
Note: In most Ex isolation amplifiers the 250 Ohm resistor is already integrated.
Current output 12...30 VDC; 4...20 mA signal output (passive)
Relays Two solid state relays working as status output, limit switch, system alarm,
cleaning control, error current or alert functionality acc. to USP<645>
• The relay contacts are electrically isolated from each other and from all other
circuits
• The output stages of the status outputs/limit switches behave like relay contacts
• Possible conditions: NO (normally open) or NC (normally closed)
Connection values:
• Maximum voltage = 30 V
• Maximum load current = 75 mA up to 55°C and 50 mA above 55°C
• Max on resistance = 10 Ohm
2.2 Dimensions
Plastic housing
Aluminium housing
Do a check of the packing list to make sure that you have all the elements given in the order.
Look at the device nameplate to ensure that the device is delivered according to your order.
Check for the correct supply voltage printed on the nameplate.
Responsibility for the use of the measuring devices with regard to suitability, intended use and
corrosion resistance of the used materials against the measured fluid lies solely with the
operator.
If the device is not used according to the operating conditions (refer to chapter "Technical data"),
the intended protection could be affected.
This device is a Group 1, Class A device as specified within CISPR11. It is intended for use in
industrial environment. There may be potential difficulties in ensuring electromagnetic
compatibility in other environments, due to conducted as well as radiated disturbances.
The manufacturer is not liable for any damage resulting from improper use or use for other than
the intended purpose.
The SHD 200 is a control unit for 4...20 mA/HART® field devices. The intended use is process
control by using the relays, the second current output and the NAMUR NE 107 signalisation by
LEDs for the HART® parameters of the connected field device. The device has been constructed
for indoor and outdoor use below the maximum altitude of 2000 m / 6562 ft.
The device must be suitable for the temperature specified (including chemical resistance).
Assembly materials and tools are not part of the delivery. Use the assembly materials and tools
in compliance with the applicable occupational health and safety directives.
All installation works on the electrical connections and mounting require to open the housing:
• Put a small flat tool (e.g. screwdriver) into the right hinge lock and open the device 1.
• Lift up the housing 2.
i Now you have access to the electronic compartment and the possibility to mount the device
on a wall.
A mounting system with a minimum load force of 0.1 kN (for example FISCHER type UX10)
suitable for the background has to be applied.
For outdoor mounting, we recommend the optional weather protection cover XGSH010000 for
wall and pipe mounting. For more flexibility and convenient mounting, we recommend wall
mounting brackets XGSH010020 for plastic housing.
For outdoor mounting, we recommend the optional weather protection cover XGSH010000 for
wall and pipe mounting. For more flexibility and convenient mounting, we recommend wall
mounting brackets XGSH010030 for aluminium housing.
1 3 5 6 7
U2 U1
+ - S Sens+ Sens- + + - UR1+ UR1- UR2+ UR2-
2 4
J K FE S A1 B1 A2 B2 C D E F G H I
SENSOR SHIELD
250:
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
LOOP2-
LOOP1-
HART+
HART-
The device is equipped with an internal HART® access for the NonEx-version (A2 and B2) that
offers the opportunity to access the field device via HART® handheld or HART® modem.
U2
+
- 1
U1
+
- 3
UR1
+
- 4
UR2
+
- 5
J K FE S A1 B1 A2 B2 C D E F G H I
250 :
SENSOR SHIELD
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
LOOP2-
LOOP1-
HART+
HART-
Do not use the integrated 250 Ohm HART® resistor of the device, when using an Ex isolation
amplifier of third-party with integrated 250 Ohm HART® resistor.
S Sens+ Sens-
U2+ U2- S Sens+ Sens- U1+ U1- UR1+ UR1- UR2+ UR2-
J K FE S A1 B1
1 A
A2 B2 C D E F G H I
SHIELD
S A1 B1
FUNC. EARTH
SENSOR+
SENSOR-
SENSOR SHIELD
RELAY1+
RELAY2+
SENSOR
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
LOOP2-
LOOP1-
HART+
HART-
SENS
SENS
SENSOR+
SENSOR-
The cable glands installed by the manufacturer are designed for a cable diameter of 3...6,5 mm
for M12 and 5...10 mm for M16. If you are using cables with a larger diameter than 3...6,5 mm for
M12 and 5...10 mm for M16, you must replace the manufacturer’s cable glands with suitable
ones. The operator is responsible for the correct sealing of cable glands.
U2+ U2-
U2+ U2- S Sens+ Sens- U1+ U1- UR1+ UR1- UR2+ UR2-
J K F
FE S A1 B1 A2 B2 C D E F G H I
SENSOR SHIELD
J K
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
LOOP2-
LOOP1-
HART+
HART-
A
LOO
LOO
LOOP2+
LOOP2-
Figure 4-4: Connection of second current output
The second current output can be either used as current output for any HART® variable or as
power supply for backlight and LEDs for NAMUR NE 107 signalisation if supported by field device
(field device must support extended command 523: Read Condensed Status Mapping Array).
Connection values:
• Maximum Voltage = 30 V
• Maximum Load Current = 75 mA up to 55°C and 50 mA above 55°C
• Max On resistance = 10 Ohm
J K FE S A1 B1 A2 B2 C D E F G H I
F G H I
SENSOR SHIELD
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
RELAY2
LOOP2-
LOOP1-
LOOP1
HART+
RELAY
HART-
A
R
RELAY1+
RELAY2+
RELAY1-
RELAY2-
U2+ U2- S Sens+ Sens- U1+ U1- UR1+ UR1- UR2+ UR2-
J K FE S A1 B1 A2 B2 C D E F G H I
A2 B2
SENSOR SHIELD
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
LOOP1+
LOOP1+
LOOP2-
LOOP1-
HART+
HART-
A
HAR
HAR
HART+
HART-
Consider that the cap needs to be closed for a protection of the electronics parts.
Observe without fail the local occupational health and safety regulations.
Any work done on the electrical components of the measuring device may only be carried out by
properly trained specialists.
When connecting the power supply, always note the safety regulations of the current state of the
art. To avoid fatal injuries, destruction or damage of the device or measuring errors, also note
the following items:
• Cables may only be connected when the power is switched off.
• Always keep the housing of the device well closed if you do not perform any installation
works. The function of the housing is to protect the electronic equipment from dust and
moisture.
• Check the nameplate and assure that the power supply meets the voltage of the device. The
device is loop powered and operates in the range of 20...30 VDC with a voltage drop < 4 V. If
the power supply is below 20 VDC the device and field device will not work. If the power supply
is above 30 VDC the device and field device sensor may be damaged/destroyed.
Do not use the integrated 250 Ohm HART® resistor of the device, when using an Ex isolation
amplifier of third-party with integrated 250 Ohm HART® resistor.
The device and the field device require a minimum operating voltage of 20 VDC. The power
supply is provided via the 2-wire interface (4...20 mA).
U1+ U1-
U2+ U2- S Sens+ Sens- U1+ U1- UR1+ UR1- UR2+ UR2-
J K FE S A1 B1 A2 B2 C D E F G H I
SENSOR SHIELD
C D E
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
RELAY1-
RELAY2-
LOOP2+
OOP1+
LOOP1+
RELAY1
LOOP2-
LOOP1-
HART+
HART-
LOOP
LOOP
LOOP1+
LOOP1+
LOOP1-
4.7 Connecting the SHD 200 for use in an active 4...20 mA current output
To avoid fatal injuries as well as destruction or damage of the device assure a correct installation
before switching on the power. This includes:
• The device is mechanically safe, mounting and power connection comply with the regulations.
• The electrical terminal compartments must be secured, i.e. the housing has to be closed and
the screws have to be tightened.
• The electrical operating data of the power supply comply with the requirements of the device.
Observe without fail the local occupational health and safety regulations.
Any work done on the electrical components of the measuring device may only be carried out by
properly trained specialists.
When connecting the power supply, always note the safety regulations of the current state of the
art. To avoid fatal injuries, destruction or damage of the device or measuring errors, also note
the following items:
• Cables may only be connected when the power is switched off.
• Always keep the housing of the device well closed if you do not perform any installation
works. The function of the housing is to protect the electronic equipment from dust and
moisture.
• Check the nameplate and assure that the power supply meets the voltage of the device. The
device is loop powered and operates in the range of 20...30 VDC with a voltage drop < 4 V. If
the power supply is below 20 VDC the device and field device will not work. If the power supply
is above 30 VDC the device and field device may be damaged/destroyed.
Do not use the integrated 250 Ohm HART® resistor of the device, when using an Ex isolation
amplifier of third-party with integrated 250 Ohm HART® resistor.
+ -
U2+ U2- S Sens+ Sens- U1+ U1- UR1+ UR1- UR2+ UR2-
J K FE S 1 A
A1 B1 A2 B2 C D E F G H I
C D E
SENSO SHIELD
FUNC. EARTH
SENSOR+
SENSOR-
RELAY1+
RELAY2+
SENSOR
RELAY1-
RELAY2-
LOOP2+
OOP1+
LOOP1+
RELAY1
LOOP2-
LOOP1-
LOOP1
HART+
HART-
LOOP
SENS
ENS
LOOP1+
LOOP1+
LOOP1-
S Sens+ Sens-
S A1 B1
Sensor Shield
Sensor+
Sensor-
+
-
Connect output + from field device to SENSOR - and output - from field device to SENSOR +.
For information on connecting the second current output refer to Connecting the second current
output on page 17 , connecting the relays refer to Connecting the relay outputs on page 18 and
connecting the external HART adapter refer to Connecting the external HART adapter on page
19.