Professional Documents
Culture Documents
Datasheet FS-8901404032W REV.B (20191205B)
Datasheet FS-8901404032W REV.B (20191205B)
-1*!Jll~~.mlm~f.:1"~~ls'.l
SHENZHEN JINGHUA DISPLAYS CO.,L TD
FS-8901404032W REV.B
PAGE 1 OF 35
DOCUMENT TITLE:
SPECIFICATION
OF
LCD MODULE TYPE
CUSTOMER
CUSTOMER APPROVAL
DATE
CONTENTS
Page No.
1. GENERAL DESCRIPTION 4
2. MECHANICAL SPECIFICATIONS 4
3. INTERFACE SIGNALS 14
5. ELECTRICAL SPECIFICATIONS 14
5.1 TYPICAL ELECTRICAL CHARACTERISTICS 14
5.2 OPTICAL CHARACTERISTICS 15
5.3 TIMING SPECIFICATIONS 17
5.4 INSTRUCTION TABLE 18
6. QUALITY UNITS 21
FINAL SPECIFICATION
FS-8901404032W REV.B
PAGE 4 OF 35
T06
:
T06 Modify exploded view 2019.07.30
JHD Environment Sign(green shading) T07 Modify Reliability Test 2019.12.04
2. 晶华所执行的标准如下:
JHD perform Environment Standard as follows :
有害物质十种含量(ppm)---ICP/GC-MS 测试方式
Ten Injurant Contents(ppm)---ICP/GC-MS Test Style
镉及镉化合物 铅及铅化合物 汞及汞化合物 6价铬化合物 多溴联苯 多溴二苯醚 邻苯二甲酸丁基苄酯 邻苯二甲酸二正丁酯 邻苯二甲酸二(2-乙基以基)酯 邻苯二甲酸二异丁酯
Cadmium and Lead and lead Mercury and Hexavalent Polybrominated Polybrominated Buty1 Benzyi Dibuty1 Di-2-ethylhexyl Diisobuty1
Cadmium compounds mercury chromium biphenyls diphenylethers phthalate phthalate phthalate phthalate
compounds compounds compounds (PBB) (PBDE) (BBP) (DBP) (DEHP) (DIBP)
<100 <1000 <1000 <1000 <1000 <1000 <1000 <1000 <1000 <1000
Light source
Protective film
Reflecting
PULL TAPE
Release film
D.S.T.
Diffusion
Protective film
PULL TAPE
Release film
D.S.T.
Release film
B/W D.S.T.
5. Electrical Specifications
5.1 Typical Electrical Characteristics
At Ta = 25 C, VDD = 3.30.1V, VSS=0V.
Table 5
Parameter Symbol Conditions Min. Typ. Max. Unit
Supply voltage (Logic) VDD-VSS Not1 3.2 3.3 3.4 V
VDD=+3.3V,
Supply voltage (LCD) VLCD 4.8 5.0 5.2 V
Note 2
VIH “H” level 0.7VDD - VDD V
Input signal voltage
VIL “L” level VSS - 0.3VDD V
Current Consumption IDD Note 1 - 31.37 47.06 uA
Note 1: The voltage is IC can support. But the display effect isn’t best.The supply current is
measured under the checkerboard pattern.
Note 2: There is tolerance in optimum LCD driving voltage during production and it will be
within the specified range. The module will be display best within 3.30.03V for VDD.
FINAL SPECIFICATION
FS-8901404032W REV.B
PAGE 15 OF 35
Transmittance
11 25℃ 14.44% 17.86%. - - -
(Module)
NEGATIVE TYPE:
FINAL SPECIFICATION
FS-8901404032W REV.B
PAGE 17 OF 35
6. Quality Units
6.1 Purpose
This standard for quality assurance should define the quality of LCD module products to customer by
JINGHUA DISPLAYS LTD, except of those with special requirements from customer.
6.3 Definition
6.3.1 Definition of area
A Zone: Active area.
Middle size(M):7~99 pcs LCD screens are cut out of from each 14"×16"unit motherglass.
Small size(S):> 99 pcs LCD screens are cut out of from each 14"×16"unit motherglass.
6.4 Quality Specification
6.4.1 Conditions of Inspection
6.4.1.1 Tests should be conducted under the following conditions:
6.4.1.2 Judging time of steady defect:3s at most(it should be ignored if it’s invisible)
With fluorescent lamps, the light should be under 300 Lux, the product should be inspected with 30cm to
LCD surface;
With fluorescent lamps, the light should be 700~1200Lux, the product should be inspected with 30cm to
LCD surface;
customer.
Major defect: It is a defect that is likely to result in failure or to reduce materially the usability of
Minor defect: It is a defect that will not result in functioning problem with deviation classified.
Multi-meter.
Caliper.
0.35<D 0
D≤0.15 Ignorance
0.15<D≤0.25 2
Small Size
0.25<D≤0.3 1
0.3<D 0
1. For the dot pattern: accept if the area of defect is less than or
equal to half of one lattice’s.
2. Only allow one defect in one segment.
3.The nearest distance allowed between two pinholes is above
20mm.
D=(X+Y)/2
When character displays, the background is
7 Limit sample Min.
deeper or lighter than sample.
8 The color of character is lighter than sample; Limit sample Min.
9 The backlight is not light; Reject Maj.
10 When working, the light is flashing; Reject Maj.
The backlight does not work or the color is
11 Reject Maj.
wrong;
12 When working, the obvious gridding is visual; Reject Min
The uniformity inspection:
As following picture, we use the 5-points test method to confirm
the uniformity, the standard is: Min/Max≥70%;
Average both length and width to 6 parts, and test points as
Back-light following( green points ):
13 Min
D>0.5 0
D≤0.15 Ignorance
Negative 0.15<D≤0.3 3
Middle Size
D>0.3 0
D≤0.15 Ignorance
Negative 0.15<D≤0.25 3
Small Size
D>0.25 0
②Zone B: the defect size is 1.5 times than Zone A;
③Zone C: Ignore the spot defect;
The distance between two defect should longer than 20mm;
④LCD display defect judged in stable picture(defect is visible
when change picture but invisible in stable picture should be
judged OK)
⑤above defects which are visible in complete display picture but
invisible in other picture should be judged OK
D=(X+Y)/2
LCD rub defect judged in stable picture
(defect is visible when change picture
Ignore
but invisible in stable picture should be
judged OK)
4 LCD rub defect which is visible in
complete display picture but invisible in Ignore
other picture should be judged OK
LCD rub defect is visible ( except
Limit sample
complete display)
The scratch / line defect on LCD or polarizer
① Zone A:
Product Defect
Defect Length Accept Qt’y
Type Width
Positive Within 1m inspection, the defect is unobvious and not Min
Large Size get bigger when display;
W≤0.02 / Ignorance
0.02<W≤0.03 L≤4 2
Positive 0.02<W≤0.03 L>4 0
5 Middle
0.03<W≤0.05 L≤3 2
Size
0.03<W≤0.05 L>3 0
W﹥0.05 / Same as the spot
W≤0.02 / Ignorance
0.02<W≤0.03 L≤4 2
Positive 0.02<W≤0.03 L>4 0
Small Size
0.03<W≤0.05 L≤2 2
0.03<W≤0.05 L>2 0
FINAL SPECIFICATION
FS-8901404032W REV.B
PAGE 29 OF 35
Min
6
ITO side Others
Zone a b c Acc Qt’y
a≤5mm(L≥5mm) b≤W c≤T 3
ITO side Min
a<L(L<5mm) b≤W c≤T 3
Others not exceed 1/2 width of seal c≤T 3
Glass chip on edge Min
7
Min
FINAL SPECIFICATION
FS-8901404032W REV.B
PAGE 30 OF 35
Others
ITO touch side ITO back side
Zone a b c Acc Qt’y
c≤1/2T
ITO touch a≤3mm(and
(T>0.7mm)
side(COG not exceed 4 b≤W/5 3
and TAB) ITO terminal c≤T(T≤0.7m
m)
ITO touch
a≤4mm(and
side(except
not exceed 4 b≤W/4 c≤T 3
COG and
ITO terminal
TAB)
c≤3/4T
ITO back
(T>0.7mm)
side(COG a≤3mm b≤1/4W 3
c≤T(T≤0.7m
and TAB)
m)
ITO back
side(except
a≤5mm b≤1/3W C≤T 3
COG and
TAB)
Not exceed
Others a≤5mm 1/2 width c≤T 3
of seal
Extended crack inspector shall attempt to remove the chip with
tweezers, re-evaluate if the remaining defect is still a crack or a
chip:
6.5 Reliability
The LCD module shall not fail the following reliability test.
“Shenzhen Jinghua Displays CO., LTD. reserves the right to change this specification”
- END –