Professional Documents
Culture Documents
MIXED
"S" LARGE
MIXED “S”
A double curvature mixed “S” roof tile where eaves
and ridge tiles assure design and functionality
to provide easy-to-install roofs with the special
characteristic beauty of the Mediterranean roofs
Double
More breakage interlocking
resistance The double interlocking
Clays composition and –horizontal and vertical-
perfect press performance allows the roof to be
make flexion rates higher more watertight, ensuring
than even the Standard ones its impermeability
The names of the colours shown in the photos, only represent the finishes of the models identified as Mixed “S”
ESR - 2727
b a
c
LARGE
MIXED “S”
Application
Standard Requirements MIXED S
54 mm d
2.12” 227 - 233 mm 10 mm
8.93” - 9.17” 0.4”
262 - 284 mm 80 - 95 mm
10.31” - 11.18” 3.14” - 3.74”
a = 80 mm / 3.15”
c
b = 355 mm / 13.97”
c = 397 mm / 15.63”
+ 20 mm* d = 10-30 mm / 0.39”-1.18”
+ 3/4” (Depending on the slope)
b
a
227 - 233 mm
262 - 284 mm 8.93” - 9.17” 304 - 324 mm *First course batten should be 20 mm (3/4”) higher than all succeding course battens to provide a vertical
10.31” - 11.18” 11.97” - 12.75” alignment and to assure a symmetrical installation
To avoid cutting the field tiles when reaching the ridge line, a 2/3 under ridge tile (Q35)
can be used in the upper course and closed by using a Double 2/3 under ridge tile (Q37).
INSTALLATION DETAILS
RIDGE
-Ridge tiles must be installed lap facing away -All ridges and hips shall be covered with self
from the prevailing winds, in order to assure adhesive Alu-Roll, La Escandella Aluminum
water tightness. roll for hip and ridges (CAM01), or similar
approved breathable waterproof underlayment.
-Field tiles at top course should be secured
Underlayment should be secured over the ridge
directly either into the deck or top batten with
nailer with non-corrosive roofing nails.
stain-less ring screw nails or similar.
-Apply ridge tiles with a minimum overlapping of
-At the top course of the roof (horizontal
5 cm (2”) through-out the ridgeline facing away
terminating end) field tiles can be finished by
from the prevailing wind-driven rain.
using either Wedges (Q08) or under ridge tiles
(Q70 and Q35).
Round ridge / Hip Round ridge end / Hip starter (with Q02)
3,400 gr 3,600 gr
7.5 lbs 75mm 7.94 lbs
2.95”
465mm
2.5 pcs/lm 220mm 18.30”
0.75 pcs/lft 8.66”
End cap round ridge (with Q02) Bardelis end cap / gable end (with Q02)
Q83 Q64
305mm 290mm
12” 11.42”
Round 3 way ridge (with Q02) Round 4 way ridge (with Q02)
Q44 Q45
4,600 gr 4,100 gr
10.14 lbs 9.04 lbs
Ø 440mm Ø 445mm
17.32” 17.52”
Two way female ridge tile Two way male ridge tile
Q65 410mm
16.14”
Q82 362mm
14.25”
3,200 gr 2,300 gr
90mm
7.05 lbs 3.54” 5.07 lbs 59mm
2.32”
255mm 222mm
10.04” 8.74”
Ridge end / hip starter End cap / straight gable end (with Q01)
Q03 410mm
16.14”
Q05 249mm / 9.8”
2,900 gr 90mm
2,100 gr
332mm
6.39 lbs 3.54” 4.63 lbs 14.25”
84mm
3.3”
250mm
9.84”
On their products, La Escandella has right to make changes in dimensions, fittings, weight & units per pallet, without previous notice. For more information, please contact your Sales Representative or our
Customer Care Service.
Round end cap / gable end (with Q01) 3 Way ridge (with Q01)
Q06 245mm
9.64” Q07 450mm / 17.71”
3 Way ridge with slope (with Q01) 3 Way ridge female (with Q01)
90mm
3,700 gr 3.54”
* 420mm 3,700 gr
16.53”
8.16 lbs 8.16 lbs 337mm
204mm 14.84”
8.03”
*375mm / 14.76”
4,650gr 3,600 gr
10.25 lbs 7.93 lbs 190mm
410mm
16.14” 2.5 pcs/lm 7.48”
130mm
0.75 pcs/lft 5.12”
Straight left side course / rake Straight right side course / rake
Q10 470mm
18.5” Q11 470mm
18.5”
3,100 gr 136mm
5.35”
3,100 gr 135mm
5.35”
6.83 lbs 87mm 6.83 lbs 87mm
3.42” 3.42”
2.5 pcs/lm 2.5 pcs/lm
165mm 165mm
0.75 pcs/lft 6.5”
0.75 pcs/lft 6.5”
Round left side course / rake Round right side course / rake
Q12 470mm
18.5” Q13 470mm
18.5”
Bardelis left side course / rake Bardelis right side course / rake
Q62 470mm
18.5” Q63 470mm
18.5”
206mm 206mm
8.11” 8.11”
2,700 gr 2,600 gr
5.95 lbs 26mm
5.73 lbs 26mm
1.02” 1.02”
2.5 pcs/lm 2.5 pcs/lm
0.75 pcs/lft 120mm 0.75 pcs/lft 120mm
4.72” 1.02”
ACCESSORIES
La Escandella offers a complete line of Large mixed “S” Roof tile accessories, available in any standard color, to customize your roof.
4,200 gr 6,100 gr
9.26 lbs 13.45 lbs
470mm 97mm
18.5” 3.82” 470mm
286mm 18.5”
11.26”
Q35 340mm
Q37
13.38” 343mm
13.5”
3,000 g 3,850 gr
6.61 lbs 8.48 lbs
286mm
11.26” 400mm
Longitudinal fit:
150mm to 195mm 5.9”
/ to 7.67” 15.75”
Channel / pan curved eave tile Ridge / cover curved eave tile
Ridge / cover eave with same slope Channel / pan eave with same slope
Half large Mixed “S” tile Double large Mixed “S” tile
2/3 Large Mixed “S” tile Large Mixed “S” ventilation tile
Q56 335mm
13.19” Q19 470mm
18.5”
2,800 gr 4,000 gr
6.17 lbs 8.81 lbs
286mm
11.26” 286mm
Longitudinal fit: 11.26”
255mm to 270mm /10” to 10.63”
On their products, La Escandella has right to make changes in dimensions, fittings, weight & units per pallet, without previous notice. For more information, please contact your Sales Representative or our
Customer Care Service.
Chimney support Large Mixed “S” tile (with Q26) Chimney support Large Mixed “S” tile (with Q53)
Q24 470mm
18.5” Q49 470mm
18.5”
4,850 gr 4,650 gr
10.7 lbs 10.25 lbs
Ø 11.5 cm Ø 13 cm
286mm 286mm
Ø 4.53” 11.26” Ø 5.12” 11.26”
Chimney support Large Mixed “S” tile (160mm / 6.3” chimney kit) Large Mixed “S” glass tile / skylight
6,500 gr 3,800 gr
14.33 lbs 8.38 lbs
470mm
Ø 16 cm 18.5” 10.5 pcs/m2
400mm 286mm
Ø 6.3” 15.75” 11.26”
Q08 121mm
4.76” Q72 220mm
8.66”
Chimney / pipe cover (with Q24) Chimney / pipe cover (with Q49) Chimney / pipe cover (with Q47)
Width: Several sizes Width: Several sizes Width: Several sizes Width: 50 mm / 1.96”
Colours: Red, paja, brown, black. Colours: Red, paja, brown, black. Colours: Red, brown, black. Colours: Red, black, brown.
CAM65 / CAM21 / CAM52 / CAM53 CAM27 / CAM70 / CAM07 / CAM10 CAM05 / CAM010 / CAM51 CAM14
Waterproof membrane Ridge Tile Hook Ridge Batten Bracket Eaves Ventilation Comb
Dimensions: 1,5 m x 50 m / 1.64 yd x Colours: Red, brown, black. Dimensions: Several sizes. Dimensions: 6cm x 1m / 2.36” x 39.37”
54.68 yd Colours: Red, black.
Weight: several weights.
CAM26 CAM62
Universal Metal-clip Universal Eave hook-clip
TECHNICAL INFORMATION
SLOPES / PITCHES
The minimum pitch standard recommendations should always be followed (see values in the referral table). On all pitches below
the standard recommended minimums, or in regions where ice dams may occur, a waterproof underlayment on the entire deck MUST
be applied. Most problems with water-shedding roof installations occur from water that migrates through the joints of the tiles
through capillarity action, wind-driven rain, and runoff or ice damming. Because of this possibility, the underlayment is critical to the
success of the roof.
WITHOUT UNDERLAYMENT WITH UNDERLAYMENT
ZONE 1 ZONE 2 ZONE 3 ZONE 1 ZONE 2 ZONE 3
Protected 25% / 14º 27% / 15,5º 30% / 17º 19% / 10º 21% / 11º 23% / 12º Protected
Hip
Normal 25% / 14º 27% / 15,5º 30% / 17º 21% / 11º 23% / 12º 26% / 14º Normal
< 6,5 m
Exposed 33% / 18,5º 37% / 20,5º 40% / 22º 28% / 15º 32% / 17º 34% / 18,8º Exposed
Protected 28% / 16º 32% / 18º 36% / 20º 22% / 12º 24% / 13º 26% / 14º Protected
Hip Normal
Normal 28% / 16º 32% / 18º 36% / 20º 24% / 13º 27% / 15º 31% / 17,5º
6,5 m - 9,5 m
Exposed 35% / 19,5º 39% / 21,5º 43% / 23,5º 30% / 17º 33% / 18º 42% / 22º Exposed
Protected 32% / 18º 35% / 19,5º 40% / 22º 23% / 12º 26% / 14º 30% / 17º Protected
Hip Normal
Normal 32% / 18º 35% / 19,5º 40% / 22º 27% / 15º 30% / 17º 34% / 18,8º
9,5 m - 12 m
Exposed 42% / 23º 45% / 24,5º 50% / 26,5º 36% / 19º 39% / 21º 43% / 23,5º Exposed
Note: For hips MORE than 12m long (39.4’), a waterproof underlayment on the entire roof deck MUST be applied and the ventilation underneath must be reinforced (check with the manufacturer).
PROTECTED LOCATIONS: hollow area which is surrounded by hills that protect the hollow from the winds in all directions..
NORMAL LOCATIONS: Flat area, plateau with minimal elevation changes.
EXPOSED LOCATIONS: Places open to strong winds, coastal areas (up to 5 km / 3 miles from the shoreline), islands or narrow peninsulas, estuaries or closed
bays, narrow valleys, isolated mountains, mountain passes and earthquake zones.
FIXATION VENTILATION
The slope of a roof determines the level of fixation of the Ventilation is one of key elements to assure a good
tiles required. The fixation of the tiles may be necessary to hygrothermal behavior of the roof and preservation of the roof
prevent the sliding of the rooftiles or to prevent their structure. The key to a good and well preserved roof is a good
lifting by the effect of the air. In eaves, right and left side ventilated roof. Proper installation of Ventilation tiles
course, lines of ridge, valleys, encounters with vertical combined with ventilated roof can result in energy savings, in
walls and other singular points, all the pieces will be a more energy efficient home.
fixed. For all other parts, the level of fixation will depend
Air should be able to flow through the eave and ridge; be sure
on the pitch.
not to close these off with cement, mortar or similar. Eave and
ridge areas should be protected to help minimize the access
of birds and vermin infiltration.
90º - 200% A free flowing ventilation area must be provided through the
A: 60º - 173% roof deck. This ventilation should be evenly distributed
B: 45º - 100% throughout the roof space to eliminate any dead air space.
A C: 0º - 0%
La Escandella recommends a minimum of 1
B Innova ventilation tile (Q19) for every 7 m2 (1.32 vent
tiles per 100 sq ft.) and with a minimum of 2 ventilation tiles
C per roof surface, installed on the upper part of the roof.
0º - 0% Using a proper ventilation system is the best way to
avoid moisture in a roof, that could cause peeling,
cracking and other defects on the tile.
1 6 4 1
2 2
3 3
9 5 9
78 6
7
8
La Escandella warranty will be honored when installation is in strict accordance with local building codes, particularly to those referring to the ventilation of the deck and minimum slope requirements.
Clay roof tiles should always be installed in full compliance with the local building codes and good tiling practice. For each country, please refer to local building codes.
www.laescandella.com
Colour Shall be Harmonized but clay tiles are a natural product and some shade variations between individual pieces enhance their beauty and should be expected. All Tiles should be blended
regardless of the number of colours supplied. Colours of the tiles shown in this catalogue can not faithfully reflect the colours of the ceramic tiles.
On their products, La Escandella has right to make changes in dimensions, fittings, weight & units per pallet, without previous notice. For more information, please contact your Sales
Representative or our Customer Service.
This catalogue, printed in October 2019, replaces the existing ones.