Professional Documents
Culture Documents
900
ROLLING SERVICE DOORS
RELIABLE AND DURABLE ROLLING SERVICE DOORS
The Wayne Dalton 900 Series rolling service door is ideal for
jobs where an economical solution for durability and strength SIZES UP TO 16' WIDE AND
16' HIGH
is needed. The 900 Series offers flexibility in substrate materials
with choices of 24, 22, or 20–gauge galvanized steel, stainless • MAX STEEL GAUGE = 20
steel, or aluminum. • 2" FLAT AND CURVED SLATS
Color options range from our five standard factory-finish colors • DURABLE & ECONOMICAL
to a full range of 180 RAL powder coat choices.
ROLLING SERVICE DOORS
900 SERIES
Popular in both interior and exterior applications, the
Wayne Dalton 900 Series rolling service door features
a galvanized, pre-painted curtain of minimum 24-gauge
steel. All 900 series doors are standard wind load rated
with a minimum of 20 PSF.
Available Options
• Secur-Vent (Flat Slat Only)
• Safety Edges
• Drop Stop Device
• Exhaust Ports
• Sloping Bottom Bars
• Powder Coated
• Motor Operators
• Cable Reels
• Mullions
• Thru-Wall Operation No. 2 slat No. 17 slat Secur-Vent®
www.Wayne-Dalton.com/commercial
ROLLING SERVICE DOORS
9 0 0 SERIES
MANUAL OPERATION
2"
X
X
ADJUSTING
WHEEL HOOD
2"
L LINTEL 8"
Y Y
D
B
ELEVATION SECTION (UNDER LINTEL) SECTION
POWER POWER
Y UNIT UNIT
Y
POWER
2"
UNIT
26"
W
X
X
ADJUSTING EMERGENCY
WHEEL HOOD HOIST
2"
OPENING HEIGHT "F"
L LINTEL
R
Y 16" Y 16"
D
D
B
ANGLE OR ROLLED – FACE MOUNTED TO MASONRY ANGLE GUIDES – MOUNTED BETWEEN JAMBS
OPENING WIDTH "A"
JAMB JAMB
JAMB JAMB
2"
X
X
ADJUSTING
WHEEL HOOD
2"
L LINTEL
8.5"
Y Y
HAND CHAIN
D
D
B
ELEVATION SECTION (UNDER LINTEL) SECTION
Y ADJUSTING Y
WHEEL 8
2"
2"
POWER
UNIT
POWER
X
X
ADJUSTING UNIT
WHEEL HOOD HOOD
2"
2"
2
L LINTEL EMERGENCY
HOIST L LINTEL
EMERGENCY ROLLER
HOIST CHAIN
WALL SLOT THRU
WALL
20"
D
B
B
side of wall.
BRACKET SIZE SIDE ROOM BRACKET SIZE SIDE ROOM BRACKET SIZE SIDE ROOM
TO 16'0" 14–1/2" 8" 6" 16-1/2" 8" 6" 18-1/2" 8" 6"
BRACKET SIZE SIDE ROOM BRACKET SIZE SIDE ROOM BRACKET SIZE SIDE ROOM
TO 16'0" 14–1/2" 4-1/4" 4-1/4" 16-1/2" 4-1/4" 4-1/4" 18-1/2" 4-1/4" 4-1/4"
www.Wayne-Dalton.com/commercial
ROLLING SERVICE DOORS
Note to specifiers: Words in brackets indicate frequently specified and highly recommended options.
PART I – GENERAL PART I I – PRODUCTS 2.08 Weatherstripping
1.01 Work Included 2.01 Curtain A. Air-Bar Extr-Tite doors will include flat slats, bottom
A. The opening will be equipped with Wayne Dalton A. Curtain will be composed of interlocking astragal, surface guide weatherstrip, and internal hood
900 Series rolling doors. [22, 20, gauge galvanized steel] [18 B&S aluminum] baffle weatherstrip.
[22, 20 stainless steel] slats, roll-formed per ASTM
1.02 Related Work standards and designed to withstand a 20 PSF 2.09 Locking
A. Opening preparation, miscellaneous or structural windload. Ends of alternate slats will be fitted with A. [Manual lift-up doors will have interior slide-bolts
metal work, access panels, finish or field painting, metal endlocks/windlocks. suitable for padlocks by others]. [Chain-hoist door
field electrical wiring, wire, conduit, fuses, and B. Bottom bar will consist of two equal steel will have chain keepers suitable for padlocks by
disconnect switches are in the Scope of Work of [stainless steel] [aluminum] angles, .121" minimum others]. [Electric-motor operation doors will lock
other divisions or trades. thickness, to stiffen curtain,with astragal. When through the operator gearing]. [Cylinder locks can
required for additional security, provide [slide bolts] be provided with the doors].
1.03 Reference Standards [cylinder locks] on the bottom bar operable from Note: When specifying locks on electric-motor operated
A. ANSI/DASMA 203 – American National [coil side] [both sides]. doors, electric interlocks should also be specified to
Standards Institute Specifications for non-rated fire prevent operation when lock bolts are engaged in the
rolling doors published by Door & Access Systems 2.02 Guides guides, thus preventing damage to the curtain
Manufacturers Association International. A. Guides will be roll-formed steel channel bolted to and/or operator.
B. ASTM A123 – Zinc [hot-dipped galvanized] angle or structural grade, three angle assembly of
coatings on iron and steel products. steel [stainless steel] [aluminum] to form a slot of 2.10 Windload
C. ASTM A229 – Steel wire, oil-tempered for sufficient depth to retain curtains in guides to A. Windload – minimum 20 psf per DASMA 102-2003
mechanical springs. achieve 20 PSF windload standard. Guides may be and as required by local codes.
D. ASTM A-653-94 – Steel sheet, zinc-coated provided with integral windlock bars and removable
[galvanized] by the hot-dipped process, bottom bar stops. PART III – EXECUTION
commercial quality. 3.01 Installation
E. ASTM E330 – Structural performance of 2.03 Brackets A. General:
exterior windows, curtain walls, and doors by A. Brackets will be of 3/16" [1/4"] minimum thick steel 1. Install doors in accordance with manufacturer’s
uniform static air pressure difference. plates, with permanently sealed ball bearings. Designed instructions and standards. Installation shall be by
to enclose ends of coil and provide support for an authorized Wayne Dalton representative.
1.04 Quality Assurance counterbalance pipe at each end. 2. Verify that existing conditions are ready to receive
A. Rolling doors and all accessories and components rolling door work.
required for complete and secure installations shall be 2.04 Counterbalance 3. Beginning of rolling door work means acceptance
manufactured as a system from one manufacturer. A. Curtain to be coiled on a pipe of sufficient size to of existing conditions.
carry door load with deflection not to exceed .033" B. Install door complete with necessary hardware, jamb
1.05 Systems Description per foot of door span and to be correctly balanced by and head mold strips, anchors, inserts, hangers, and
A. Rolling Door: Type: helical springs, oil tempered torsion type. Cast iron equipment supports in accordance with final shop
Model 900 barrel plugs will be used to anchor springs to drawings, manufacturer’s instructions, and as specified
B. Mounting: [steel] [wood] [masonry] jambs. tension shaft and pipe. herein.
C. Operation: [manual push-up] [crank] [chain hoist] C. Fit, align and adjust rolling door assemblies level and
[motor] [motor with chain hoist]. 2.05 Hood plumb for smooth operation.
D. Material: Galvanized steel with polyester finish paint. A. Hood will be minimum 24-gauge [aluminum 22 gauge D. Upon completion of final installation, lubricate, test
B&S] [galvanized] [stainless steel] sheet metal, flanged and adjust doors to operate easily, free from warp
1.06 Submittals at top for attachment to header and flanged at wist or distortion and fitting for entire perimeter.
A. Shop Drawings: Clearly indicate the following: bottom to provide longitudinal stiffness. Hood will Note: Architect may consider providing a schedule when
1. Design and installation details to withstand enclose curtain coil and counterbalance mechanism. more than one rolling door or opening type is
standard windload. required.
2. All details required for complete operation 2.06 Finish
and installation. A. Shop coat of rust inhibitive primer on non-galvanized
3. Hardware locations. surfaces and operating mechanisms. Guides and
4. Type of metal and finish for door sections. bracket plates will be coated with a flat black prime
5. Finish for miscellaneous components and paint. Aluminum finish to be [mill] [204R1 clear
accessories. anodized] [bronze anodized]. Stainless steel finish
B. Product Data: Indicating manufacturer’s product available. Curtain color will be [white] [green] [gray]
data, and installation instructions. [beige] [brown] (white, green, beige, brown only avail
able as 24 or 22 gauge). Powder coating is available in
1.07 Delivery, Handling, Storage 180 colors.
A. Deliver products in manufacturer’s original containers,
dry, undamaged, seals and labels intact. 2.07 Operation
B. Store and protect products in accordance with A. Door will be operated by means of [manual, lift-up]
manufacturer’s recommendations. [chain hoist with gear drive reduction] [awning crank]
[wall crank box] [motor operation]. Optional
1.08 Warranty [electrical] [pneumatic] sensing edge to be attached to
A. Standard manufacturer’s one year warranty against bottom bar to [stop and reverse] the door when it
defects in material and workmanship. contacts an object during the closing cycle.
Distributed By: