Professional Documents
Culture Documents
Sikalastic®-841 ST
LIQUID APPLIED PURE POLYUREA MEMBRANE
1/3
PRODUCT INFORMATION
Chemical Base Pure Polyurea
Packaging Part A (Isocyanate) 212 kg drums approx. 189 litres
Part B (Amine) 191 kg drums approx. 189 litres
TECHNICAL INFORMATION
Shore D Hardness ~ 45–50 (DIN 53505)
Mechanical Resistance ~ 230 mg H22 / 1000 g / 1000 cy (ISO 5470-1)
~ 100 mg H17 / 1000 g / 1000 cy
APPLICATION INFORMATION
Mixing Ratio Part A : Part B = 1 : 1 volume
Consumption approx. 1.05 kg/m2/mm
Layer Thickness > 2 mm (Crucial System)
≥ 1.5 mm (Standard System)
Product Temperature > +65°C
Ambient Air Temperature -20 °C … +50 °C
Relative Air Humidity < 85 %
Substrate Temperature +1 °C … +50 °C
≥ 3 °C above dew point, beware of condensation
Curing Time 24 h / +20 °C
Gel time ~ 11 sec / +20 °C
Waiting Time / Overcoating 1 to 2 min / +20 °C
2/3
APPLICATION INSTRUCTIONS LOCAL RESTRICTIONS
Coating System Product Consumption Please note that as a result of specific local regulations
System for 1 x Sikafloor®- 0.3–0.5 kg/m2 the performance of this product may vary from coun-
concrete struc- 156 or try to country. Please consult the local Product Data
tures 1 x Sikafloor®- Sheet for the exact description of the application
161 fields.
System for Lightly broadcast
concrete struc- with quartz sand, 1.0–1.5 kg/m2 ECOLOGY, HEALTH AND SAFETY
tures 0.3–0.8 mm
System for 1 x Sikalastic®- ~ 1.06 kg/m2/mm For information and advice on the safe handling, stor-
concrete struc- 841 ST age and disposal of chemical products, users shall
tures refer to the most recent Material Safety Data Sheet
(MSDS) containing physical, ecological, toxicological
and other safety-related data.
Dose and mix with a suitable air driven or electrical
plural component heated spray equipment. Both com- VOC DATA
ponents must be heated up to +70 °C. The accuracy of
mixing and dosage must be controlled regularly with According to the EU-Directive 2004/42, the maximum
the equipment. Thoroughly stir part B (Amine) using a allowed content of VOC (Product category IIA / j type
drum stirrer until a homogenous colour is obtained. sb) is 500 g/litre (Limits 2010) for the ready to use
product.
CLEANING OF TOOLS The maximum content of Sikalastic®-841 ST is < 500
g/litre VOC for the ready to use product.
Clean all tools with Thinner C immediately after use.
The application equipment has to cleaned and filled
with Mesamoll. Hardened and/or cured material can
LEGAL NOTES
only be removed mechanically. The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
LIMITATIONS products, are given in good faith based on Sika’s cur-
rent knowledge and experience of the products when
▪ This product may only be used by experienced pro- properly stored, handled and applied under normal
fessionals. conditions in accordance with Sika’s recommenda-
▪ For spray application the use of protective health
tions. In practice, the differences in materials, sub-
and safety equipment is mandatory.
▪ The maximum layer thickness per application pass strates and actual site conditions are such that no war-
shall not exceed 4mm, for the build-up of higher ranty in respect of merchantability or of fitness for a
thickness several passes have to applied. particular purpose, nor any liability arising out of any
▪ UV light exposure may lead to yellowing and chalking legal relationship whatsoever, can be inferred either
▪ The performance and technical properties of from this information, or from any written recom-
Sikalastic®-841 ST are not affected by UV exposure. mendations, or from any other advice offered. The
Sikalastic®-841 ST is UV light resistant but may lead user of the product must test the product’s suitability
to yellowing and surface chalking under UV expos- for the intended application and purpose. Sika re-
ure. serves the right to change the properties of its
products. The proprietary rights of third parties must
BASIS OF PRODUCT DATA be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
All technical data stated in this Product Data Sheet are refer to the most recent issue of the local Product
based on laboratory tests. Actual measured data may Data Sheet for the product concerned, copies of which
vary due to circumstances beyond our control. will be supplied on request. It may be necessary to ad-
apt the above disclaimer to specific local laws and reg-
ulations. Any changes to this disclaimer may only be
implemented with permission of Sika® Corporate Legal
in Baar.
Sikalastic-841ST-en-HK-(12-2019)-1-5.pdf
3/3