Professional Documents
Culture Documents
Introduction Manual
Thank you for purchasing our R/C system.
Before using, read this manual carefully.
N-6H (LCD) FM
N-6H (LCD) 2.4G
DIGITAL PROPORTIONAL R/C SYSTEM N-6H
Table of Contents
6.3
.3 V-Tail Connection Diagram Caution 1
1.1 N-6H(LCD) Transmitter Chart 2
Transmitter Receiver channel mixing 1.2 N-6H Transmitter Chart(BACK) 3
Ch4 1.3 N-6H(LCD) Basic features 4
Stick Ch2
1.4 LED displaying board function 4
Elevator Stick +50% -50% 1.5 Menu 5
Rudder Sticker +50% +50% 2.1 Sys. menu introduction 5
2.2 MODEL. SET 6
2.3 MODULATE 8
! Switch to “V-Tail” position and enter V-Tail mode, elevator and Rudder is
2.4 PLANE TYPE 8
mixed, as for V-Tail planes.
2.5 STICK MODE 9
! Receiver channel distribution:
CH1: Aileron 2.6 STICK ADJ 9
CH2: Elevator 2.7 CHANNEL (FOR 2.4G RC) 9
CH3: Throttle 3.1 D/R 10
CH4: Rudder 3.2 SUB TRIM 11
CH5: Aileron2 3.3 TRAVLE 12
3.4 CH. REV 12
3.5 SWASH. MIX 13
3.6 GYRO. SENS 13
6.4 DALTA-MIX Connection Diagram 3.7 THRO. CURV 14
3.8 MONITOR 14
Transmitter Receiver channel mixing 3.9 PIT. CURV 15
Ch2 Ch5 3.10 THRO.HOLD 15
Stick Ch1
4.1 Function menu for fixed wing plane 16
Aileron Stick +50% +50% +50%
4.2 V-Tail menu 16
Elevator Sticker +50% -50% +50% 4.3 Delta mix function menu 17
5.1 Upright Operation of Left Stick and Movement of Elevator 18
5.2 Level Operation of Left Stick and Movement of Rudder 19
! Switch to “DALTA” position and enter DALTA-MIX mode, aileron and elevator
5.3 Upright Operation of Right Stick and Movement of Throttle 19
is mixed, as for triangle planes, tailless planes, discal planes.
5.4 Level Operation of Right Stick and Movement of Aileron 20
! Receiver channel distribution:
CH1: Aileron 6.1 Heli. Connection Diagram(3Servos CCPM) 21
CH2: Elevator 6.2 Airplane Connection Diagram 22
CH3: Throttle 6.3 V-Tail Connection Diagram 23
CH4: Rudder 6.4 DALTA-MIX Connection Diagram 23
CH5: Aileron2 2.4G Radio Data Transmission 24
Technology Data
! Switch to “HELIC” position and enter HELI. mode. 1.1 N-6H Transmitter Chart
Antenna Handle
ELEV D/R SW AILE D/R SW
IDLE SW TH. Hold
(Heli.)PIT.ADJ GYRO.SENS(Heli.)
Flap CH(Plane)
(Plane)Gear CH
LED Digital Trim
Left Stick Right Stick
2.4G BIND SETTING (FOR 2.4G RC)
Digital Trim
1. Select ‘CHANNEL’ and enter the interface. Press
“ENTER” to come to the interface. Eyelet
2. Before setting ID Code, Please plug the short jack into Digital Trim Digital Trim
the “Ch1”(RP-8 RX) or “BAND”(XY900 RX) channel of
Power SW
the receiver and then turn on the receiver power, now the
receiver will come to the ID Code setting mode. LCD Charging Jack
Motor
THRO. AILE.
Transmitter
(Mode 1) Servo 1 Servo 2 ! Press “Data decrease/downward selection button” to select “SYS MENU” (“Data
decrease/downward selection button” hereafter as “-:”)
AILE.
! Press “Data increase/upward selection button” to select “FUN MENU”, (“Data
RUDD.
increase/ upward selection button” hereafter as “+”)
! Press “ENTER” to come to the menu or selection menu, and “EXIT” to leave the
current operation and save the setting.
LEFT STICK RIGHT STICK
M
Rudder Plane 1.4 LED displaying board function
Left Stick O
Horizontal CHARGE CHARGE
L Stick
Operation R R
Rightwards
!"POWER”LED
5.3 Upright Operation of Right Stick and Movement of Throttle The light keeps on with red color in normal power-on condition.
When the voltage is below 8.6v, the light blinks with alarming. Now please exit the
operation and change new battery.
Reverse: Normal
Throttle: Right
!"CHARGE”LED
M It is time to recharge the battery in the transmitter if the light has no response in normal
Motor Plane power-on condition.
O Right Stick 1)Please be sure that the rechargeable NiH or Ni-Cd in the box is properly connected
Ve r t i c a l before charging.
R Stick 2)Turn off the power and pull out the crystal ( can accelerate the charging )
Decelerating Decelerating Operation 3)When the charger (12v) is connected with the transmitter, LED will blink circularly to
Downwards
show the battery is in the charging status.
4)When the battery is fully charged (about 11.6v), LED stops blinking. ( the charging
R Stick period depends on the charger and battery)
Accelerating Accelerating
Upwards
GYRO. SENS
FUN.MENU GYRO. SENS 0 STICK DR ELEV 0 EL EV DR SW ELEV D/R
1
CH. REV GYRO. SEN S P OS0 /POS1 0
POS0 -20 H 100 1
P OS0 /POS1
SWASH. MIX RU I 0
ENTER POS1 100 STICK: O 0
GYRO.SEN
ELEV.
EL L -75
!Gyro sensitivity adjustment !D/R operation for ELEV dual band
Operation Operation
1)Press “+” to select 'FUN MENU', and press “ENTER” to come to the interface. 1)Press “+” to select 'FUN MENU', and press “ENTER” to come to the interface.
2)Press “-” or “+” to select 'GYRO SENS', and now the shadow area is the item that can 2)Press “-” or “+” to select 'D/R', and now the shadow area is the item that can be set
be set currently. Press “ENTER” to go to the next step. currently. Press “ENTER” to go to the next step.
3)Set “GYRO SENS” switch on the top of the transmitter: 3)Press “ENTER” to select 'ELEV D/R', and LCD shows the corresponding “AILE 0” or
When “GYRO SENS” is in ‘0' position, LCD shows “POS 0”, and now you can set the “AILE 1”.
value for “POS 0” by “+” or “-”. 4)Move the stick to ELEV direction (see the above chart) to select 'H' or 'L', and press
当When “GYRO SENS” is in '1' position, LCD shows “POS 1”, and now you can set the “+” or “-” to set the corresponding value and dual band curve will change accordingly.
value for “POS 1” by “+” or “- 5)Set “ELEV D/R” switch on the top of the transmitter
6)After your setting, press “EXIT” to save the setting and leave the operation. When “ELEV D/R” is in '0' position, LCD shows “ELEV 0”, and now you can set D/R
value for “ELEV 0”;
And when “ELEV D/R” is in '1' position, LCD shows “ELEV 1”, and now you can set D/R
value for “ELEV 1”
6)After your setting, press “EXIT” to save the setting and leave the operation.
STICK MODE STICK MODE STICK MODE STICK MODE IDLE SW IDLE SW THRO. CURV THRO. CURV
MODE 1 MODE 2 MODE 3 MODE 4 OFF O FF/pos 0
0 /pos1 NOR IDLE 1
RU AI RU AI AI RU AI RU 1 I 0 I 20
EL TH TH EL EL TH TH EL O 0 O 20
L -75 H 75
!Stick mode selection
Operation !Throttle curve operation
1)Press “-” to select “SYS MENU”, and press “ENTER” to come to the interface; Operation
2)Press “-” or “+” to select 'STICK MODE', and now the shadow area is the item that can 1)Press “+” to select 'FUN MENU', and press “ENTER” to come to the interface.
be set currently. Press “ENTER” to go to the next step. 2)Press “-” or “+” to select 'THRO CURV', and now the shadow area is the item that can
3)Press “-” or “+” to select 'MODE 1' (right throttle), 'MODE 2' (left throttle), 'MODE 3' be set currently. Press “ENTER” to go to the next step.
, 'MODE 4'. And press “ENTER” to save the selection and press “EXIT” to leave the 3)Press “ENTER” to select the throttle curve point. There are 5 points, they are L, 1, 2, 3,
operation. H. Press “-” or “+” to set the corresponding value separately, and the throttle curve will
Remark:This operation changes the distribution of 4 proportional channels. Please change accordingly.
note: 'AILE', 'ELEV', 'THRO' and 'RUDD' channels have been distributed now. 4)There are three throttle curves to be selected, normal, IDLE 0 and IDLE 1 by the switch
When the stick mode is changed, the menu order controlled by the stick 'AI' and at the left top of the transmitter.
'EL' is also changed. Please pay attention to the difference. When “IDLE SW” is in “OFF” position, the transmitter is in normal condition and
supports normal flying mode of helicopter ;
2.6 STICK ADJ When “IDLE SW” is in “0” position, the transmitter supports 3D flying mode of
helicopter;
SYS.MENU SYS.MENU SYS.MENU ;When “IDLE SW” is in “1” position, the transmitter supports 3D flying mode of
STICK MODE STICK MODE STICK MODE
RENAME helicopter;
RENAME
Adjust? Adjust 5)After your setting, press “EXIT” to save the setting and leave the operation.
STICK ADJ STICK ADJ STICK ADJAS
SAVE Remark: the transmitter can save 3 groups of different throttle curves. When you
ENTER
NO ENTER make 3D fly, please ask for instruction from experienced pilots.
Remark: the data of the current model number group will overlay another data
group, so please be careful.
STICK
4.2 V-Tail menu
MODEL MOD0 MODEL MOD0
RENAME RENAME !V-Tail function menu includes: neutral trim, servo travel, channel reverse, and stick
RU RECOVER.. monitor. Please see the corresponding description in the helicopter function menu for the
STICK: SAVE AS SAVE AS operation .
ELEV.
EL RECOVER RECOVER
V-TAIL
FUN.MENU
“ENTER”
CH.REV ELEV 1 50
!Recover the factory data ELEV 2 50
MONITOR
Operation: ENTER RUDD2 50
1)Press “-” to select “SYS MENU”, and press “ENTER” to come to the interface; V-TAIL RUDD1 50
2)Once again press “ENTER” to come to “MODEL SET” interface, and now the shadow
area is the item that can be set currently. !V-Tail
V-Tail mixing
3)Move the stick to ELEV direction (see the above chart) to select the setting item, and
press “ENTER” to come to “RECOVER” Operation ( plane type is V-Tail)
4)Press “ENTER” to recover the factory setting, and press “EXIT” to leave the menu. 1)Press “+” to select 'FUN MENU', and press “ENTER” to come to the interface.
2)Press “-” or “+” to select 'V-TAIL', and now the shadow area is the item that can be set
Remark: This recovery will clear the data of the current model number, please be currently. Press “ENTER” to go to the next step.
careful. 3)Press “ENTER” to select ELEV1, ELEV2, RUDD 1, RUDD 2. And set the mixing
value by “+” or “-”.
4)After your setting, press “EXIT” to save the setting and leave the operation.
GYRO.SEN
THRO. CURV
THRO. HOLD
Elevator
!SYS. MENU Elevat o r
PPM /PCM 2.4G
MODEL. SET MODEL. SET
MODULATE PLANE TYPE
PLANE TYPE STICK MODE
STICK MODE STICK ADJ
STICK ADJ CHANNEL
Aileron
Crystal(FM)
Bind(2.4G) Aileron
Reverse: Normal
Throttle: Right
Battery Box
M
Aileron Plane
O Right Stick
Horizontal
R Stick R Operation
Rightwards
Technology Data
6-Ch RC 6-Ch RC
Type: N-6H N-6H
Specification: LCD LCD
Channels: 6 6
F requency: 35/36/40/41/72M 2.4G
(One type of them)