New Bucky Board Installation Instructions
Technical Service Bulletin
Product:
True Speed Bucky
‘Summary:
‘The following document will define the steps necessary to replace the old
Style Bucky board (Part # 10-0800) with the new style Bucky board (Part #
10-08048).
Tools Required:
Phillips head Screw Driver
Wire Cutters
Parts Required:
Bucky Board: 10-08048
If you are replacing the board on a Bucky with the old style GRAY
connector, you will need The Connector Plate Assembly: 10-20006
FORM: 00-02-1675 ECN: P2790 REV. A aNew Bucky Board Installation Instructions
"These stallation instructions wil guido you Uirough the instalation process ofthe new bucky Board, ]
+ fhe Bucky hasan orange connector, proceed with the steps outlined below.
ifthe Bucky has a Gray connector proceed with the steps outined on page 11
| Bucky withthe Grange Connaetor
Tamove te Philips Read Sew
that connects the motor to the
ona: 0002-1675 EcN: 279New Bucky Board Installation Instructions
Turn the Bucky on sside and
remove the 6 screws that hold
the mator i place,
= Bucy on is back Ute
motor unplug the mator fom
connector 1, and remevethe
motor from the machine,
FORM; 0002-1675 ECN:P2790 REV.ANew Bucky Board Installation Instructions
‘Unplug the orange connector]
from the Bucky.
FORMH: 0002-1675 EEN: £2790 REV. A 4New Bucky Board Installation Instructions
‘Uns the comnectors fom the
votage selector
Unplug Connector
FORM#: 0002-2675 ECN: P2790 REV. 5New Bucky Board Installation Instructions
[ The wiring bundle canbe tacked]
away 2 shown in the image. Ts
‘wiring bundle wl ot be sed
again
Insulate any bare conductors.
‘emove the old board fom the
uni by eamoving tha sbeserows
securing the board down,
sen: 2790 REV.A 6New Bucky Board Installation Instructions
The naw Bucky board hasthe
‘connector already sidered onto
a
lace the board nto the unand
ORM: 0002-1675 ECN: P2790 REV.A 7New Bucky Board Installation Instructions
log nthe connector
|__|
[ Connect te naw ground wire te
| Se chasis stud
ORI: 00002-1675 ECN:P2790 REV.A. 8New Bucky Board Installation Instructions
2 Motor Connector
TReinsert the motor and secure
withthe 6 serews underneath the
| by,
FORMH: 00002-1675 ECN: P2790 REV.ANew Bucky Board Installation Instructions
a Secure the motor tothe Gri
Th Suc snow end Se "Switch Steg
| Speed, exposure Delay, and Stroke Length
Font: 00.02-1675 ECN:P2790 REV.ANew Bucky Board Installation Instructions
‘These incallation instructions will ude you through te instalation procan ofthe new Buaky board]
with the Gray connector.
‘Bucky with the Gray Connector
| Remove the Philips headcrew |
that connects the mato tothe
era
FORM: 00.02.1675 GCN: 2780 REV. A aNew Bucky Board Installation Instructions
"Turn the Bucky on salle and
remove the 6 sews that hold
‘the meter in place.
a
ace the Buaky on sb Ut
the mater, unplug the motor
tor, and remove
rom the machine,
FORM: 00.02.1675 ECN:P2790 REV. 2New Bucky Board Installation Instructions
[ Unpiog te connectors trom the |
voltage selector
‘Disconnect 13 rom the Buoy
Board
FORM: 00.02.2675 ECN:P2790 REV.A 3New Bucky Board Installation Instructions
Disoaneet 2 ram the Boy
fox.
‘Unierew the two Philip head
screws that mount the
Connector to the frame ofthe
Bucky
‘Gt wires at connect to
the Gray Connector.
This connector will not be used
3eain
FORM: 00.02.1675 ECN: P2790 REV.A “New Bucky Board Installation Instructions
insulate the Bare wires and Wack
‘the wires avay as shown inthe
Inculat the bare conductors.
Taal We New Bucky Boardin
the unit and secure with a
Philos head sere
et
FORM: 00-02-1675 ECN:P2790 REV. ANew Bucky Board Installation Instructions
‘Conmoet the New Connectorto |
‘the Bucky Board as shown,
‘Secure the mounting plato
the chasse wih the screws
provided
‘Connect the new around wire to
‘the Chassis ground stud
FORMM: 0002-1675 ECN: P2790 REV.A 16New Bucky Board Installation Instructions
lug te nator into connector
a.
Tenaer the motor and secre
the Bucky.
FORM: 00021675 EEN: P2780 REV.A
vNew Bucky Board Installation Instructions
Te-Secure the motor tothe Grd
| Te acy naw ready See Switch Settings for instructions on how to setup the Bucky for Gre
Speed, Exposure Delay and Stroke Leng
FORM: 0002-2675 ECN:P2700 REV.A 8New Bucky Board Installation Instructions
Switch Settings
‘Switch Settings for new Bucky Motor. The fllowlng sultch settings wil allow yout adapt your new
board to your environment,
swi
Switeh 1 Grid Speed
Par Speed
Switch 2 Exposure Delay
25 milsecond
“Tigger at Center Off
Switeh and 4~ Stroke Length
3off, df= 104
3 off, 4 on 088
FoRI#:00.02-1675 EcN: 2790 REV. A