Professional Documents
Culture Documents
使用手册
Elevator
Door Conroller
Axxonsafe(Suzhou)Elevator parts TechnologyCo.,Ltd. Directions
Wujiang Friendship Development Zone Suzhou China
中国 苏州 吴江友谊开发区
TEL 电话:86 512 8516 0999
FAX 传真:86 512 816 0666
Email:sales@axxonsafe.com
HEADQUARTERS:0512-85160999-SALES DEPARTMENT
总部:0512-85160999-销售部
SHANGHAI OFFICE 上海办事处:13372168057
JIANGSU OFFECE 江苏办事处:13372168053
ZHEJIANG OFFICE 浙江办事处:13372168050
BEIJING OFFICE 北京办事处:13372168055
SHENYANG OFFECE 沈阳办事处:13372168052
GUANGDONG OFFICE 广东办事处:13372168059
WWW.axxonsafe .COM
全 国 免 费 服 务 热 线 :800-808-6688
-1-
Magnetic switch Test Procedures
For Transducers
Lf the parameters of the transducer are changed before testing it,reset the parameter of
(1) Connect control cables,and then Magnetic switch whether the logic of the
transducer is
Right or not:
P08=1 P09=1
displays”F**”
P09=0 FR=3HZ
Action.
The choice of input signal detection mode 2, both by the "A contact input",
● Settings
2
terminal level "L"), the detection ON
● Set method
0-4bit will transform into a 10-band input.
When the case opened ( 4bit )( and closed variable-speed signal 3bit ),
transmission signal for the entry point B,
Terminal 7 6 5 4 3
NO.
bit 4 3 2 1 0
Value 16 8 4 2 1
addition
Note command signals to open and close the command signal logic can not
Plan1-1
二、Test Procedures
2.1 Checking the connecting cables
Checking the cables to the transducer, the encoder and traveling cables.After making sure they are
2.2 For parameters needed tobe changed and their setting values,pleaserefer to table2-1
4
NO The
volues
参数 值 描述 设置范围 备注
P08 1 Automatic
5
P08 2 Control-cabnet
Magneticswitch
P52 50 50~999
constant
Theclearance of
P42 1 0,1,2
the set data
Undcr thc user-dcfined mode,any10 paramctcrs can be chosen from parameters in thc
arca of p and 1 where chents oftcn make changes By doing so,datg can be simplificd
more..
read in the non-easy-easu storagc,and will bc sascd evcn in the case of power failarc
The user-defined mode are the U01-u10 which allows user to reail the 10 freqieat;v
Enter into the menu no f the transducer and ob serve the display of the display of the n16。See
figure 2-1 1representing the signal of phase B of the encoder 2 representing the
Pull the hanging plate manually,the flickering of the 1 and 2 means that the signals
displayofthe transducer
6
2.4Che self-study of the door width
doingopenaction:secondlypressthe?key,thenpresstheRUNkey,andconfirmthe
doorisdoingclosedaction,lfthedoorkeepsmotionlessormovestooslow,youcan
increase the PO5 and set the Fr equal to 3.0: if the door moves the other way
round ,you can exchange two of phases U,V and W arbitranily: then return to the
originalinterfacebypressingSTOPkeyafterfinishing.
There is certain running curve for the door motor when doing open and closed door actions after the
finishing of the self-study for the door width, but the running curve maybe isn t smooth and steady
enough and some light bump will appear, so the running curve should be adjusted precisely.
The door open adjustment curve can be seen in figure 2-2 The door closed adjustment curve can be
seen in figure2-3
d50=0.6.
plan2-3
7
8
三、Repair and maintenance
3.1Regular Maintenance ltems of the Elevator
(b)Wipe guide rails and inject lubrication grease on the surface of them,Check
rollers abrasion loss and change them,if the loss is over 1.55mm
(c)Regularly adjust the timing belt to meet the requirements as shown in Fig3-1
(a)Make sure that the motor is stable when door closed or open,and without any abnormal
9
sound.
Any problems arising from the above procedures should be handled immediately.
Measures and actions should be taken to make sure that the door ekevator works smoothly
Function statement
The function schedule consists of two parts:the parameters of area
P:P01~P79 and the parameters of area D:d00~d53.
The parameters of area P:P01~d79
NO Function title Enactment area The
out-of-foctory
dota
heat-sensibve function
power
10
★P11 Stop frequency 0.5~60 0.5
frequency
limiting
restarting afrer
instantaneous stop
linear speed
11
★P32 The maximum outout voltage 0/1~500 0
messages
out-of-foctory
doto
information
transducer
arriving signal
enooder abnrmity
amvingSW
12
★P48 RY 1 function choice 0~7/r0~r7 7
★P53 0
★P54 1.0
★P55 0.0
★P56 1.0
★P57 0.0
★P58 5.0
frequency 1)
frequency 2
cunrent 1
cunrent 2
frequencytor the
sandwiching(low speed)
13
★P66 The switching time of the 0.5~250 5.0
sandwiching adjudgement
sandwiching detection
the aboomal
cpen-actionadjudging time
abnomal open-action)
keepingtime
keepingtime
decelerating function
choice
slippage arnval
slippage arrival
slippage open-arrival
14
Note(1)refers to pararaeters that can be changcd when operation.
Theout-of-factory
NO Function title Enactment area
doto
15
arrival open(Hz)
16
NO Function title Enactment area 出厂数据
Openarrivedstandby to maintain
d43 0.5~250 0.5
frequency(Hz)
Closearrivedmaintainstandby
d46 0.0~10 0.5
time(sec)
17