Professional Documents
Culture Documents
2 – Hazards identification
Avoid contact with skin and clothing. Do not breathe vapor, use only with adequate
ventilation. Wash thoroughly when appropriate
5 – Fire-fighting measures
• Suitable extinguishing media: Water haze, foam, fire-extinguishing powder, carbon dioxide.
• Not suitable extinguishing media: Water with full jet.
• Special exposure hazards: Formation of toxic gases will occur during overheating or in case of fire.
• Protective equipment: Wear fully protective suit with self contained breathing apparatus
(SCBA) with a face-piece operated in positive pressure mode.
• Handling: Wear appropriate personal protection when handling. Avoid inhalation of vapors.
• Storage: Store in a cool, dry place in tightly closed receptacles. Keep away from heat.
• Components with limit values that require monitoring at the workplace: None established
• Engineering measures: Use only with adequate ventilation or use respiratory protection.
• Suitable gloves: Nitrile rubber (NBR). Selection of gloves should take in consideration the quality aspect
(thickness, strength, etc.) which varies from manufacturer to manufacturer.
11 – Toxicological information
• Toxicological information
12 – Ecological information
• General notes: Toxic to some aquatic organisms. Prevent material to reach ground water, waterways or
sewage system.
• Ecotoxicity data: Not available
• Persistence and biodegradability: Not available
• Mobility: Not available
13 – Disposal consideration
• Waste disposal: Disposal must be in accordance with applicable Federal, State and local regulations.
• Remarks: Do not allow material to enter drains, sewers or surface water.
14 – Transport information
• Regulatory status
(UN/ IMDG/IATA ; DOT/TDG): Not regulated for transport
15 – Regulatory information
• U.S. Federal regulations:
TSCA: All components listed.
SARA 302; 304; 311/312; 313: None of the ingredient listed.
• Canadian regulations:
DSL: All components listed
WHMIS classification: D2B - Toxic materials causing other effects;
16 – Other information
To the best of our knowledge, the information contained herein is accurate at the date of its publication. However,
this shall not constitute a guarantee for any specific product features and shall not establish a legally valid
contractual relationship. The data relates only to the specific product designated and does not relate to use of the
product in any process or in combination with any other material.
* 1 Identification of substance
· Product details
· Trade name: Spabond 340 Extra Slow Hardener
· Application of the substance / the preparation Epoxy curing agent
· Manufacturer/Supplier:
GURIT (UK) Ltd GURIT (Canada) Inc.
St. CROSS BUSINESS PARK 175, rue Péladeau
NEWPORT I.O.W. Magog (Québec)
PO30 5WU J1X 5G9
UNITED KINGDOM Canada
TEL:+44(0)1983 828000 T: +1 819 847 2182
FAX:+44(0)1983 828100 F: +1 819 847 2572
· Information department: Product safety department.
· Emergency information: Contact as above
* 2 Composition/Data on components
· Chemical characterization
· Description: Mixture of the substances listed below with nonhazardous additions.
· Dangerous components:
9046-10-0 Polyoxyalkyleneamine 25-50%
2855-13-2 3-aminomethyl-3,5,5-trimethylcyclohexylamine 10-25%
100-51-6 Benzyl alcohol 2.5-10%
3 Hazards identification
· Hazard description:
C Corrosive
DR
Page 2/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 1)
· HMIS-ratings (scale 0 - 4)
HEALTH 3 Health = 3
FIRE 1 Fire = 1
REACTIVITY 0 Reactivity = 0
DR
Page 3/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 2)
Keep away from heat and direct sunlight.
· Information about protection against explosions and fires: No special measures required.
· Storage:
· Requirements to be met by storerooms and receptacles: No special requirements.
· Information about storage in one common storage facility: Not required.
· Further information about storage conditions: Keep receptacle tightly sealed.
Protective gloves
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the
resistance of the glove material can not be calculated in advance and has therefore to be checked prior to
the application.
· Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
observed.
· For the permanent contact of a maximum of 15 minutes gloves made of the following materials are
suitable:
Nitrile rubber, NBR
· Eye protection: Safety glasses
· Body protection: Protective work clothing
DR
Page 4/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 3)
11 Toxicological information
· Acute toxicity:
· LD/LC50 values that are relevant for classification:
9046-10-0 Polyoxyalkyleneamine
Oral LD50 2855 mg/kg (rat)
Dermal LD50 2980 mg/kg (rab)
· Primary irritant effect:
· on the skin: Caustic effect on skin and mucous membranes.
· on the eye: Strong caustic effect.
· Sensitization: Sensitization possible through skin contact.
· Additional toxicological information:
The product shows the following dangers according to internally approved calculation methods for
preparations:
Corrosive
Irritant
Swallowing will lead to a strong caustic effect on mouth and throat and to the danger of perforation of
esophagus and stomach.
12 Ecological information
· General notes:
Water hazard class 1 (Self-assessment): slightly hazardous for water
(Contd. on page 5)
USA
DR
Page 5/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 4)
Do not allow product to reach ground water, water course or sewage system.
* 13 Disposal considerations
· Product:
· Recommendation:
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
· Uncleaned packagings:
· Recommendation:
Packagings that cannot be cleansed are to be disposed of in the same manner as the product.
14 Transport information
· DOT regulations:
· Hazard class: 8
· Identification number: UN3259
· Packing group: II
· Proper shipping name (technical name): P O L Y A M I N E S , S O L I D , C O R R O S I V E , N.O.S.
(Polyoxyalkyleneamine, ISOPHORONEDIAMINE)
· Label 8
· Land transport ADR/RID (cross-border):
· IMDG Class: 8
· UN Number: 3259
· Label 8
· Packaging group: II
· EMS Number: F-A,S-B
· Marine pollutant: No
(Contd. on page 6)
USA
DR
Page 6/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 5)
· ICAO/IATA Class: 8
· UN/ID Number: 3259
· Label 8
· Packaging group: II
· Propper shipping name: POLYAMINES, SOLID, CORROSIVE, N.O.S.
(Polyoxyalkyleneamine, ISOPHORONEDIAMINE)
* 15 Regulations
· Sara
· Section 355 (extremely hazardous substances):
None of the ingredient is listed.
· Section 313 (Specific toxic chemical listings):
None of the ingredients is listed.
· TSCA (Toxic Substances Control Act):
All ingredients are listed.
· Proposition 65
· Chemicals known to cause cancer:
None of the ingredients is listed.
· Chemicals known to cause reproductive toxicity for females:
None of the ingredients is listed.
· Chemicals known to cause reproductive toxicity for males:
None of the ingredients is listed.
· Chemicals known to cause developmental toxicity:
None of the ingredients is listed.
· Cancerogenity categories
· EPA (Environmental Protection Agency)
None of the ingredients is listed.
· IARC (International Agency for Research on Cancer)
7631-86-9 silicon dioxide, chemically prepared 3
· NTP (National Toxicology Program)
None of the ingredients is listed.
· TLV (Threshold Limit Value established by ACGIH)
None of the ingredients is listed.
· MAK (German Maximum Workplace Concentration)
None of the ingredients is listed.
(Contd. on page 7)
USA
DR
Page 7/7
Material Safety Data Sheet
acc. to ISO/DIS 11014
Printing date 05/06/2008 Reviewed on 05/06/2008
(Contd. of page 6)
· NIOSH-Ca (National Institute for Occupational Safety and Health)
None of the ingredients is listed.
· OSHA-Ca (Occupational Safety & Health Administration)
None of the ingredients is listed.
· Product related hazard informations:
The product has been classified and marked in accordance with directives on hazardous materials.
· Hazard symbols:
C Corrosive
· Hazard-determining components of labelling:
3-aminomethyl-3,5,5-trimethylcyclohexylamine
Benzyl alcohol
Polyoxyalkyleneamine
· Risk phrases:
Causes burns.
May cause sensitization by skin contact.
· Safety phrases:
When using do not eat or drink.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
After contact with skin, wash immediately with plenty of water
Wear suitable protective clothing, gloves and eye/face protection.
In case of accident or if you feel unwell, seek medical advice immediately.
This material and its container must be disposed of as hazardous waste.
· National regulations:
All components in this formulation are listed in the EPA TSCA chemical inventory. They comply with
applicable rules and orders of the regulations.
· Technical instructions (air):
Class Share in %
II 3.9
· Water hazard class: Water hazard class 1 (Self-assessment): slightly hazardous for water.
* 16 Other information
This information is based on our present knowledge. However, this shall not constitute a guarantee for any
specific product features and shall not establish a legally valid contractual relationship.
· Department issuing MSDS: Health, Safety & Environmental department.
· Contact: SIMON RHODES
· * Data compared to the previous version altered.
USA
DR