Professional Documents
Culture Documents
369842c 1 10.31.16
CCI COM
Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4
COM
MUX
MUX
product is compatible with Lutron® HomeWorks® QS
CCI
HomeWorks® QS 120 - 240 V~
systems only. This document describes the following LQSE-4A1-D 50 / 60 Hz 4 A Inc. Cont. Eq. 243C
product: lutron.com
®
50 / 60 Hz 4 A ε
1Ax4
dimming.
LQSE-4A1-D (shown)
Features
• Leading-edge or trailing-edge dimming for
incandescent / halogen, electronic / magnetic
low-voltage, and neon / cold cathode light sources.
• Controls dimmable CFL / LED loads. Refer to
www.lutron.com/LEDtool for compatibility with
dimmable CFL / LED light sources.
• RTISS Equipped® technology compensates for incoming
line-voltage variations (up to ± 2% change in frequency /
second) such as changes in RMS voltage, frequency
shifts, harmonics and line noise.
• Integral protection for temporary over-current and
over-voltage conditions.
• SSL7 compliant for compatibility with Solid State Lighting.
• Includes QS link for seamless connection to a
HomeWorks® QS system.
• LEDs on module provide diagnostic information.
• Buttons on module provide load override control.
• Manual Override Contact Closure Input (CCI).
• Power failure memory.
HomeWorks® QS
LQSE-4S1-D 120 - 240 V~ 1 A
L N N N N N 1 2 3 4
Up to 99
QS Link QS devices
Adaptive
Power HomeWorks® QS
Module Processor
CCI COM
(HQP6-2)
Guestroom Control Unit
Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4 GCU-HOSP
COM
MUX
MUX
CCI
lutron.com + 1.800.523.9466
+ 44.(0)20.7680.4481
Assembled in U.S.A.
50015757 Rev. A
® S P E C I F I C AT I O N S U B M I T TA L Page 1
Job Name: Model Numbers:
Job Number:
HomeWorksR QS DIN Power Module Phase Adaptive Fixture Controller
369842c 2 10.31.16
Specifications
Regulatory Approvals Manual Mode Operation
• 120–240 V~ 50/60 Hz • By default, each zone is set to Auto Detect non-dim
- UL® Listed load type. See QS Dimming and Switching Power
- cUL® Listed Module Installation Guide at www.lutron.com for
details on programming the load type.
- NOM Certified
• Zone buttons on the unit can be used to:
• 220–240 V~ 50/60 Hz
– turn loads on and off.
- IEC/EN 60669
– dim loads up and down when configured to a
• Lutron® Quality Systems registered to ISO 9001.2008
dimmed load type.
Power
Manual Override Contact Closure Input (CCI)
• 120–240 V~ 50/60 Hz (cULus and NOM)
• When the CCI is open, the Adaptive Power Module
• 220–240 V~ 50/60 Hz (IEC/EN 60669)
will enter Manual Override Mode, which will turn on all
• Single input feed loads to their manual override level and disable control
• 4 A maximum total input current of local zones and QS devices.
• Lightning strike protection meets ANSI/IEEE standard • When the CCI is closed or jumpered (factory default),
C62.41 and IEC 61000-4-5. Can withstand voltage Adaptive Power Module zones will return to the settings
surges of up to 6 000 V~ and current surges of up to or levels they were at prior to entering Manual Override
3 000 A. Mode.
• ESD protected above agency requirements per
Programming and Compatibility Requirements
IEC 60669-2-1
• LQSE-4A1-D can be used with only a
• For ungrounded delta feed applications, contact Lutron.
HomeWorks® QS system.
Environment • Setup and programming of the Adaptive Power
• For thermal specifications, see Output Zone Rating Module is done through the HomeWorks® QS
and Mounting section programming software.
• Relative humidity: less than 90% non-condensing • HomeWorks® QS software version 9.0 or higher is
• For indoor use only required.
Job Number:
HomeWorksR QS DIN Power Module Phase Adaptive Fixture Controller
369842c 3 10.31.16
Specifications (continued)
Output Zone Ratings
• No Derating is required if all the conditions below are met: • Special considerations:
– Calibration point maximum is 70 ºC (158 ºF). – When controlling lamps, Lutron recommends using
– Room ambient temperature is between 0 ºC and 30 ºC permanently installed fixtures.
(32 ºF and 86 ºF). – If controlling plug-in lamps, installation must ensure a
method of preventing non-rated loads being plugged
– Panel ambient temperature, within 20 mm (0.80 in) of into the unit. An example is a dedicated receptacle
unit, is between 0 ºC and 50 ºC (32 ºF and 122 ºF). with an alternate plug type.
• 25 W (@120 V~) / 50 W (@240 V~): Derating on – Controlling loads outside the parameters listed in the
all zones is required for a single module in a non- table below, may damage the device and void the
ventilated enclosure if the room ambient temperature is warranty.
between 30 ºC and 40 ºC (86 ºF and 104 ºF). • Output must be directly connected to the load,
• 50 W (@120 V~) / 100 W (@240 V~): Derating on outputs are not compatible with load side switching
all zones is required in a multiple row non-ventilated (i.e., breakers, switches, etc.).
enclosure if the temperature is between 30 ºC and • Run a separate neutral for each load circuit. A
40 ºC (86 ºF and 104 ºF). common neutral connection is not recommended.
• Each zone has a 5 W (incandescent) minimum • Maximum wire length between Adaptive Power
load requirement. For LED compatibility details, Module and the load must be less than 30.5 m
see www.lutron.com/LEDTool and Application note (100 ft).
#557. • Unit may be powered by Ground Fault Interrupter
• Does not support non-dimmable loads (GFI) or Residual Current Circuit Breaker with
• Automatically selects leading-edge or trailing-edge Overload (RCBO) protected circuit if required. Load
dimming when configured to "Auto-detect". It can also circuit wiring (from breaker to unit to load) must be
be configured for a specific load type. run in its own non-metallic conduit, or nuisance
• One load type per zone. tripping may occur.
• This module is designed to control loads with ratings • For applications requiring 0–10 V- control, use a
as noted in the table below. Outputs cannot be used Ten Volt Interface (GRX-TVI) or a 0–10 V Adaptive
to control general purpose receptacles. Power Module (LQSE-4T10-D).
• For applications requiring higher wattage ratings, use
NGRX-PB, NGRX-ELVI or LQSE-4A-D for 230 V~ or
Each zone is rated for the following wattage and load typesA: PHPM-PA for 120 V~.
Zones 1 – 4
Load Type
120 V~ 220 V~ 230 V~ 240 V~
Incandescent / Halogen 120 W 220 W 230 W 240 W
Electronic Low-Voltage 120 W 220 W 230 W 240 W
Magnetic Low-VoltageB 120 VA (90 W C) 220 VA (165 W C) 230 VA (172 W C) 240 VA (180 W C)
Neon / Cold CathodeB 120 VA (90 W C) 220 VA (165 W C) 230 VA (172 W C) 240 VA (180 W C)
Hi-lume® A-Series LTE 120 VA 1-6 drivers N/A N/A N/A
A Refer to www.lutron.com/LEDtool and Application Note #557 for compatibility with dimmable CFL / LED light sources.
B Only use iron core transformers intended for use with an electronic switch or dimmer per Clause 8.3 of IEC / EN 60669-2-1.
C Actual lamp wattage.
® S P E C I F I C AT I O N S U B M I T TA L Page 3
Job Name: Model Numbers:
Job Number:
HomeWorksR QS DIN Power Module Phase Adaptive Fixture Controller
369842c 4 10.31.16
Mechanical Dimensions
CCI COM
Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4
COM
MUX
MUX
CCI
89.7 mm 60.6 mm
HomeWorks® QS 120 - 240 V~
LQSE-4A1-D 50 / 60 Hz 4 A Inc. Cont. Eq. 243C (3.53 in) (2.38 in)
+1.610.282.3800 220 - 240 V~
lutron.com 50 / 60 Hz 4 A ε
® 1Ax4
161.7 mm
(6.37 in)
Mounting
• Mount in IP20 (minimum) rated consumer panel or breaker
panel with integrated DIN rail.
• For United States and Canada, use NEMA Type 1
minimum rated enclosure.
• Unit is 9 DIN modules (161.7 mm [6.37 in]) wide.
CCI COM
CCI COM
CCI COM
• Mount in an accessible and serviceable location. Prog. Prog.
Zn.
Prog.
1 Zn.
Zn.
Zn.12 1 Zn.
Zn.
Zn.23 2Zn.
Zn.
Zn.343 Zn.
Zn.44
COM
COM
COM
MUX
MUX
MUX
MUX
MUX
MUX
CCI
CCI
CCI
• Unit may be mounted by pressing the unit onto the DIN rail HomeWorks
HomeWorks
HomeWorks
® QS
LQSE-4A1-D
LQSE-4A1-D
® ®QS
LQSE-4A1-D
QS 120 - 240
120
50 / 60 Hz
120
V~
5050
- 240
/ 460
/A
- 240
60
V~V~
HzHz4 A
4A Inc. Cont. Eq.
Inc.
243C
Inc.
Cont.
Cont.
Eq.Eq.
243C
243C
with the clips locked. To remove the unit from the DIN rail, +1.610.282.3800
+1.610.282.3800
+1.610.282.3800
lutron.com
lutron.com
lutron.com
220 - 240
220
50 / 60 Hz
220
V~
5050
- 240
/ 460
/A
- 240
60
Hz
V~V~
εHz4 A4 Aε ε
1 A x 41 A 1A x 4x 4
unlock the clips using a screwdriver.
® ® ®
L LNL NNN N NN
N NN
N N N N NDL1 DL2DL1
DL3
DL1
DL2
DL4
DL2
DL3
DL3
DL4
DL4
® S P E C I F I C AT I O N S U B M I T TA L Page 4
Job Name: Model Numbers:
Job Number:
HomeWorksR QS DIN Power Module Phase Adaptive Fixture Controller
369842c 5 10.31.16
CCI COM
• Follow appropriate local and national codes to avoid violating required separation guidelines.
Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4
COM
MUX
MUX
CCI
IEC PELV/NEC® Class 2
CCI QS Link
CCI COM
lutron.com
og. Zn. 1 Zn. 2 Zn. 3 Zn. 4
+1.610.282.3800 220 - 240 V~
COM
MUX
MUX
lutron.com 50 / 60 Hz 4 A ε
1Ax4
CCI
® 1Ax4
®
L N N N N N DL1 DL2 DL3 DL4
Zone 3
Zone 4
Hot/Line
To additional
modules
CCI COM
Earth
® QS 120 - 240 V~
50 / 60 Hz 4 A Inc. Cont. Eq. 243C
CCI COM
CCI COM
servicing unit. Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4 Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4
COM
COM
MUX
MUX
MUX
MUX
CCI
CCI
• CCI is local control only and cannot control other
HomeWorks
units over the QS link. CCI on multiple units may® QS
be HomeWorks
Note: ® QS
= No connection 120 - 240 V~
50 / 60 Hz 4 A
connected to an emergency or manual LQSE-4A1-Doverride LQSE-4A1-D Inc. Cont. Eq. 243C
COM
CCI COM
Prog. Zn.
Prog. Zn.11 Zn.
Zn.22 Zn.
Zn.33 Zn.
Zn.44
COM
COM
MUX
MUX
MUX
MUX
Mode.
CCI
CCI
CCI
HomeWorks®® QS
HomeWorks QS 120- -240
120 240V~
V~
– Controls connected to a unit in Manual Override LQSE-4A1-D
LQSE-4A1-D 50/ /60
50 60Hz
Hz 44AA Inc.Cont.
Inc. Cont.Eq.
Eq.243C
243C
+1.610.282.3800
Mode will continue to affect units on the link that are
+1.610.282.3800 220- -240
220 240V~
V~
lutron.com
lutron.com 50/ /60
50 Hz 44AAεε
60Hz
®® 11AAxx44
® S P E C I F I C AT I O N S U B M I T TA L Page 6
Job Name: Model Numbers:
Job Number:
HomeWorksR QS DIN Power Module Phase Adaptive Fixture Controller
369842c 7 10.31.16
CCI COM
(2 000 ft). Prog. Zn. 1 Zn. 2 Zn. 3 Zn. 4
COM
MUX
MUX
CCI
• Wire Gauge:
- Control (terminals 1 and 2): 1 pair 1.0 mm2 HomeWorks ® QS
COM
CCI COM
(18 AWG).
Prog. Zn.
Prog. Zn.11 Zn.
Zn.22 Zn.
Zn.33 Zn.
Zn.44
COM
COM
MUX
MUX
MUX
MUX
LQSE-4A1-D
CCI
CCI
CCI
HomeWorks QS
HomeWorks QS
- Data (terminals 3 and 4): 1 pair 0.5 mm2 to +1.610.282.3800 LQSE-4A1-D
LQSE-4A1-D
®® 120--240
120
50//60
50
240V~
60Hz
V~
Hz 44AA Inc.Cont.
Inc. Cont.Eq.
Eq.243C
243C
shielded.
®® 11AAxx44
®
LL NN NN NN NN NN DL1 DL2
DL1 DL2 DL3
DL3 DL4
DL4
® S P E C I F I C AT I O N S U B M I T TA L Page 7
Job Name: Model Numbers:
Job Number: