Professional Documents
Culture Documents
com
YK130
High Definition
Plasma Torch
Features
It is a high definition air cooling torch designed under 160A current
Special designed multilayer compressed air channel with swirl
ring, get reliable cutting performance, vertical cutting surface and
smooth cut experience
With fast cutting speed, high piercing height, well protected shield
and long working life consumables
Torch assembly
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Torch assembly
Shield Big retaining cap Small retaining cap Vortex ring Electrode Nozzle Water tube
YIKUAI: A plasma cutting torch brand born with craftsman sprit
Note: The above parameters are only for reference, please adjust it according to actual working conditions.
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Features
New dual water cooling channel design (for both electrode and
nozzle), highly increases the consumables working life
Unique air channel design, gets more reliable cutting performance,
more vertical cutting surface and more smoothly cut
This torch with wide application to work with different plasma
power source, especially suitable for finish machining cut
Work-
Nozzle Gas Piercing Positioning Cutting Cutting
piece Current
diameter Pressure time height height speed Remarks
thickness (A)
(mm) (Mpa) (s) (mm) (mm) (mm/min)
(mm)
6 80-100 1.7 0.5 0.3 5-8 5-8 1500-2300
8 80-120 1.7 0.5 0.3 5-8 5-8 1500-2000 This data is based
on carbon steel,
10 80-120 1.7 0.5 0.5 5-8 5-8 1000-1500
if cut stainless
12 100-120 1.7 0.5 0.5 5-8 5-8 1000-1500 steel, copper and
14 120-160 1.7 0.5 0.7 5-8 5-8 1000-1500 aluminum, please
reduce the cutting
16 120-160 1.9 0.5 0.8 5-8 5-8 1000-1300 speed accordingly.
18 150-180 1.9 0.5 1 5-8 5-8 800-1300 If increase the
cutting speed,
20 200-220 1.9 0.5 1 8-10 5-8 800-1200 current should be
25 220-250 2.3/2.5 0.5 1.2 8-10 5-8 700-1000 increased together,
nozzle diameter
30 250-280 2.5/2.8 0.5 1.5 8-10 5-8 700-1000
should be changed
35 300-320 2.8/3.2 0.5 1.8 8-10 5-8 600-900 accordingly.
40 320-350 2.8/3.2 0.5 2 8-10 5-8 600-900
Note: The above parameters are only for reference, please adjust it according to actual working conditions.
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Torch assembly
Shield Small retaining cap Big retaining cap Electrode Nozzle Air core
YIKUAI: A plasma cutting torch brand born with craftsman sprit
Work-
Nozzle Gas Piercing Positioning Cutting Cutting
piece Current
diameter Pressure time height height speed Remarks
thickness (A)
(mm) (Mpa) (s) (mm) (mm) (mm/min)
(mm)
0.5-2 40-60 1.3 0.45-0.5 0.1 5-6 4-6 3500-6000
This data is based
3 50-70 1.3 0.45-0.5 0.2 5-6 4-6 2000-2800 on carbon steel,
if cut stainless
4 60-80 1.3 0.45-0.5 0.2 5-6 4-6 1700-2300 steel, copper and
aluminum, please
5 70-90 1.6 0.45-0.5 0.3 6-8 5-8 1600-2200
reduce the cutting
6 80-100 1.6 0.45-0.5 0.3 6-8 5-8 1500-2000 speed accordingly.
If increase the
8 80-100 1.6 0.45-0.5 0.4 6-8 5-8 1300-1500 cutting speed,
current should
10 80-100 1.6 0.5-0.55 0.5 6-8 5-8 1000-1300
be increased
12 100-120 1.6 0.5-0.55 0.6 8-10 5-8 900-1000 together, nozzle
diameter should
14 100-120 1.6 0.5-0.55 0.8 8-10 5-8 700-850 be changed
accordingly
16 100-120 1.8 0.55-0.6 1 8-10 5-8 600-700
Note: The above parameters are only for reference, please adjust it according to actual working conditions.
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Torch assembly
Work-
Nozzle Gas Piercing Positioning Cutting Cutting
piece Current
diameter Pressure time height height speed Remarks
thickness (A)
(mm) (Mpa) (s) (mm) (mm) (mm/min)
(mm)
0.5-2 40-60 1.3 0.45-0.5 0.1 5-6 4-6 3500-6000 This data is based
4 60-80 1.3 0.45-0.5 0.2 5-6 4-6 2000-3200 on carbon steel,
if cut stainless
5 70-90 1.6 0.45-0.5 0.3 6-8 5-8 1900-2500 steel, copper and
aluminum, please
6 80-100 1.6 0.45-0.5 0.3 6-8 5-8 1600-2200 reduce the cutting
speed accordingly.
8 80-100 1.6 0.45-0.5 0.4 6-8 5-8 1300-1800
If increase the
10 80-100 1.6 0.5-0.55 0.5 6-8 5-8 1100-1550 cutting speed,
current should be
12 100-120 1.6 0.5-0.55 0.6 8-10 5-8 1100-1550 increased together,
nozzle diameter
14 100-120 1.6 0.5-0.55 0.8 8-10 5-8 850-1000 should be changed
16 100-120 1.8 0.55-0.6 1 8-10 5-8 650-950 accordingly
Note: The above parameters are only for reference, please adjust it according to actual working conditions.
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 1.5mm
Torch assembly
Shield Small retaining cap Big retaining cap Electrode Nozzle Water tube
YIKUAI: A plasma cutting torch brand born with craftsman sprit
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Torch assembly
Shield Small retaining cap Big retaining cap Electrode Nozzle Water tube
YIKUAI: A plasma cutting torch brand born with craftsman sprit
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
Torch assembly
Note: The above parameters are only for reference, please adjust it according to actual working conditions.
Please change the nozzle and electrode when the following situation occurs
1. Cutting gap become larger 2. Cannot start the arc
3. Cutting area color getting much abnormal 4. Arc distinguish
5. Cutting speed suddenly decrease 6. Cutting nozzle getting seriously burned
7. Cutting nozzle melted on the work-piece 8. The electrode center sunk up to 2mm
www.westweld.com
www.westweld.com
40~160A
2~35mm
50mm
60mm
www.westweld.com
www.westweld.com
www.westweld.com
www.westweld.com