Professional Documents
Culture Documents
1. Study of tools like Unity, Maya, 3DS MAX, AR toolkit, Vuforia and Blender.
2. Use the primitive objects and apply various projection types by handling camera.
3. Download objects from asset store and apply various lighting and shading effects.
4. Model three dimensional objects using various modelling techniques and apply textures
over them.
5. Create three dimensional realistic scenes and develop simple virtual reality enabled mobile
applications which have limited interactivity.
7. Develop VR enabled applications using motion trackers and sensors incorporating full
haptic interactivity.
TOTAL: 60 PERIODS
LAB EXERCISES
1. Download, install and explore the features of Python for data analytics.
a) Frequency distributions
c) Variability
d) Normal curves
e) Correlation and scatter plots
f) Correlation coefficient
g) Regression
6. Use the standard benchmark data set for performing the following:
7. Apply supervised learning algorithms and unsupervised learning algorithms on any data
set.
3. Analysis of breadth first and depth first search in terms of time and space
5. Implement the non-parametric locally weighted regression algorithm in order to fit data
points.
Select appropriate data set for your experiment and draw graphs
6. Write a program to demonstrate the working of the decision tree based algorithm.
7. Build an artificial neural network by implementing the back propagation algorithm and test
the same using appropriate data sets.
Unsupervised learning
Note:
Experiments
1. Design and animate Piston Cylinder assembly and motion study using CAD software.
2. Design and simulate Connecting rod and crank shaft using CAD software.
3. Design and simulate Two Cylinder Engine assembly using CAD software.
6. Buckling analysis
4. Sensor Interfacing with ADC to 8051 and DAC & RTC Interfacing with 8051. .
6. Step Motor (Unipolar & Bipolar Motor) and PWM Servo Motor Control to Interfacing
with 8051.
11. Stepper Motor and Servo Motor Control Using ARM Processor.
2. Buckling analysis
5. CFD simulation of flow and heat transfer analysis of Double Pipe Counter Flow Heat
Exchanger
EXPERIMENTS
1. Design and animate Piston Cylinder assembly and motion study using CAD software.
2. Design and simulate Connecting rod and crank shaft
4. Design and simulate Two Cylinder Engine assembly using CAD software.
MECHATRONICS
LIST OF EXPERIMENTS:
10. Vision based image acquisition and processing technique for inspection and
classification.
INTERNET OF THINGS
3. Write a program to interface sensors to display the data on the screen through internet.
4. Interface the sensors with microcontroller/SBC and write a program to turn ON/OFF
Solenoid valve through internet when sensor data is detected.
LIST OF EXPERIMENTS:
3. Determination of heat transfer coefficient of air under natural convection and forced
convection.
5. Determination of heat flux under pool boiling and flow boiling in various regimes.
7. Determination of friction factor, heat transfer coefficient of cold/hot fluid and effectiveness
of a tube-in-tube heat exchanger.
3D GEOMETRIC MODELLING 30
1.CAD Introduction
Sketch:
Surface modeling: Extrude, Sweep, Trim, Mesh of curves and Free form.
2. Plummer Block
3. Screw Jack
4. Lathe Tailstock
5. Universal Joint
6. Machine Vice
7. Stuffing box
8. Crosshead
9. Safety Valves
12. Piston
13. Crankshaft
* Students may also be trained in manual drawing of some of the above components (specify
the number –progressive arrangement of 3D)
i) Linear Cutting.
UNIT – I METROLOGY 30
LIST OF EXPERIMENTS
1. Calibration and use of linear measuring instruments – Vernier caliper, micrometer, Vernier
height gauge, depth micrometer, bore gauge, telescopic gauge, Comparators.
2. Measurement of angles using bevel protractor, sine bar, autocollimator, precision level.
List of Experiments:
List of Experiments
List of Experiments:
LIST OF EXPERIMENTS
LIST OF EXPERIMENTS
LIST OF EXPERIMENTS
1. Fabricating simple structural shapes using Gas Metal Arc Welding machine.
3. Taper Turning and Eccentric Turning on circular parts using lathe machine.
4. Knurling, external and internal thread cutting on circular parts using lathe machine.
5. Shaping – Square and Hexagonal Heads on circular parts using shaper machine.
LIST OF EXPERIMENTS
PLUMBING WORK:
a) Connecting various basic pipe fittings like valves, taps, coupling, unions, reducers, elbows
and other components which are commonly used in household.
WOOD WORK:
a) Sawing,
b) Planing and
c) Making joints like T-Joint, Mortise joint and Tenon joint and Dovetail joint.
a) Introduction to switches, fuses, indicators and lamps - Basic switch board wiring with
lamp, fan and three pin socket
b) Staircase wiring
f) Study of Fan Regulator (Resistor type and Electronic type using Diac/Triac/quadrac)
WELDING WORK:
a) Welding of Butt Joints, Lap Joints, and Tee Joints using arc welding.
a) (simple)Turning.
b) (simple)Drilling.
c) (simple)Tapping.
ASSEMBLY WORK:
a) Assembling a centrifugal pump.
FOUNDRY WORK:
SOLDERING WORK:
TOTAL = 60 PERIOD