Professional Documents
Culture Documents
Pagina 1 di 4
(/CONTACT.PHP)
(/) (/SEARCH.PHP)
(/MEMBERSAREA.PHP)
This standard covers continuously rolled hot rolled flat products of rolled widths > 600 mm in stainless steels. It
therefore is designed to replace EN 10051. The maximum width is increased to 2500 mm compared to EN 10051.
Tolerances are defined for thickness is < 13mm. Special agreement is required for > 13mm.
The tolerances are the same for all grades of stainless steel. This is in contrast to previous standards and previous
drafts of this standard.
This simple categorisation removes the apparent omission from EN 10051 of duplex and precipitation hardening
steels. It also removes the difference between ferritic and martensitic grades and non-Mo austenitics.
Thickness
These tolerances include crown. If an agreement on crown is agreed separately, the measurement of crwon shall be
from the centre-line to a point at least 40mm from the edges for products with mill edges and at least 25mm from the
edges for products with trimmed edges.
The thickness
This site usesshall be measured
cookies. at any
Please read point
our at least
cookie 40mm
policy from the edges for products
(/cookie_policy.php) for with mill edges and at least
Close Message
25mm from the edges for products with trimmed edges.
information on what cookies are and how we use them on. By continuing to use
this website we assume you are happy to receive cookies from our website in
The tolerances shall not apply to the uncropped ends of the coil for a total length L in metres which is calculated
accordance with our cookie policy.
using the formula:
https://www.bssa.org.uk/topics.php?article=303 14/06/2018
Article: Tolerances to ISO 9444 Part 2 for continuously rolled wide hot rolled strip, ... Pagina 2 di 4
L = 90/t (in mm) provided that the result does not exceed 20 metres per coil.
For widths up to 30mm, the thickness is measured at any point on the longitudinal axis.
For widths above 30mm it is measured at any point at least 10mm or 15mm from the longitudinal edges for slit or mill
edges respectively.
EN 10051 was somewhat ambiguous in this area. This standard is quite specific.
Permitted thickness difference within one coil for cold rolling wide strip
The thickness (within one coil) shall change gradually and shall not occur with visible discontinuity.
Length tolerance
These apply to both wide and narrow products cut from coils
Tolerances
Specified length (L)
LowerUpper
L < 2000 0 + 10
2000 < L < 20000 0 + 0.005 x L
L > 20000To be agreed
The length shall be measured along one of the longer edges of the sheet/plate.
Width tolerance
For wide strip and sheet/plate cut from wide strip with thickness < 10mm, the tolerance on width is +20/-0 for mill
edges and +5/-0 for slit edges. For thickness > 10mm, the width tolerance shall be agreed at the time of enquiry and
order.
Flatness
For plate/sheet cut from wide strip of thickness < 13mm, the flatness tolerance shall be as in table below.
The flatness shall be determined by measuring the deviation in distance between the product and a flat horizontal
This site uses cookies. Please read our cookie policy (/cookie_policy.php) for Close Message
surface on which it is placed.
information on what cookies are and how we use them on. By continuing to use
this
Outwebsite we assume you are happy to receive cookies from our website in
of squareness
accordance with our cookie policy.
This shall not exceed 1% of the actual width of the plate as defined by the diagram below:
https://www.bssa.org.uk/topics.php?article=303 14/06/2018
Article: Tolerances to ISO 9444 Part 2 for continuously rolled wide hot rolled strip, ... Pagina 3 di 4
Edge camber
For hot rolled wide strip, the edge camber shall not exceed 20mm of any length of 5000 mm in the case of strip with
mill edges and 15 mm in the case of strip with trimmed edges.
For sheet/plate cut from wide strip edge camber shall not exceed 0.5% of the specified length for a specified length
of < 5000mm.
For sheet/plate cut from wide strip with a specified length > 5000mm, the edge camber shall not exceed 20mm for
any length of 5000mm for sheet/plate with mill edges and 15mm for sheet/plate with slit edges.
Superposition of dimensions
By agreement at the time of enquiry and order the tolerances on out of squareness and edge camber may be
This site uses cookies. Please read our cookie policy (/cookie_policy.php) for
replaced by a requirement that a perfect rectangle of the ordered dimensions can be superimposed on Close Message
the delivered
information on what cookies
sheets/plates or cut lengths. are and how we use them on. By continuing to use
this website we assume you are happy to receive cookies from our website in
accordance with our cookie policy.
https://www.bssa.org.uk/topics.php?article=303 14/06/2018
Article: Tolerances to ISO 9444 Part 2 for continuously rolled wide hot rolled strip, ... Pagina 4 di 4
top
Site Map (/sitemap.php) Terms & Conditions (/terms.php) Members Area (/membersarea.php)
Cookie Policy (/cookie_policy.php)
Office and Postal Address: BSSA, Regus, Blades Enterprise Centre, John Street, Sheffield S2 4SW
Registered Office: Pegasus House, 463A Glossop Road, Sheffield S10 2QD
This site uses cookies. Please read our cookie policy (/cookie_policy.php) for Close Message
information on what cookies are and how we use them on. By continuing to use
this website we assume you are happy to receive cookies from our website in
accordance with our cookie policy.
https://www.bssa.org.uk/topics.php?article=303 14/06/2018