Professional Documents
Culture Documents
D-FV-AM54_1 Field
Variable Area Flowmeters
Series AM54
2
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
For General Purpose Applications Only (for Hazardous Applications, See Page 8)
Gas Damping
Used for pulsating or unstable flows and to
avoid compression oscillations (float bounce)
when metering gases at low pressures.
Certifications
Pressure test
Welder, dye penetrant and process tests
Material Certificates EN 10204-3.1B
3
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
Design Feature:
Explosion-proof pressure tight housing designed
for hazardous environments. FM & CSA
approvals.
Alarm signal as a compact subassembly for later
upgrade
Indication of the alarm settings visible from the
outside.
Alarm settings made at the scale.
Ball bearing, decouple proof and hysteresis free
magnet follower system.
Difference between min. - and max. alarm
signals < 5%
Assembly and disassembly of the secondary
and the primary is possible without opening the
indicator housing.
Reproducibility +/-0.25% of maximum flowrate
capacity.
Round Indicator housing.
4
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
HART communication
1. via FSK modem in point-to-point or multidrop mode.
2. via ABB Automation Products HART multiplexer.
Transmission mode
FSK modulation to 4 - 20 mA current output to Bell
202 Standard, max. signal amplitude 1.2 m Ass.
Design Features: 32
5
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
Damping
Adjustable from 1 to 100 s, acc. to 5 t
Auxiliary power
Explosion Proof: 10 to 46 Vdc
Dust Ignition Proof: 10 to 46 Vdc
Non Incendive 10 to 28 Vdc
Intrinsically Safe 10 to 28 Vdc
Residual ripple: max. 5% or ± 1.5 Vss
Power consumption
<1W
Replacement of electronics
The electronics can be replaced in the event of a
fault. Settings are immediately updated when the
unit is switched on.
6
Funktionserde
32
RB 3. Min-Max alarm
The Min-Max alarm can be programmed as NC
42 or NO.
41
Ambient Temperature:
Fig. 7 - Loading diagram, current output The correlation between the temperature class,
Load over auxiliary power permissible ambient temperature and maximum
measurement material temperature is shown in
Programmable output diagrams on page 8.
Terminals 41/42 can be freely programmed.
The following options can be programmed by way of
the Prog Output software:
7
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
Safety data
Limit value contacts terminals 41/42, 51/52
Terminals 41, 51 are positive (+)
The permissible maximums of protection type
Technical data
Hazardous environments version AM 54331/32
FM Approval Report: 3008432
max. insulation =
CSA: File Number: 176935-1146812 flange diameter
Fig. 9
Model AM5433_ _ can only be used in temperature
classes T1 to T4.
AM54331-32/72-74, Insulated
max. fluid temperature (TM) ambient temperature (Tu)
Hazardous environments approval data
Terminals 31/41
Power Supply Ui = 28 V
Terminals 31/32 Ii = 110 mA
Pi = 770 mW
AM54372-74
Um = 60 V Ci = 4,2 nF
Ci/PA = 6 nF
AM54331-32
Li = 270 mH
Switching output Ui - 15 V
Terminals 41/42 Ii = 30 mA
Pi = 115 mW
Um = 60 V Ci = 3,6 nF
Ci/PA = 3,6 nF
Li = 133 mH
AM54331-32/72-74
max. fluid temperature (TM) ambient temperature (Tu)
Fig.10
AM54372-74
AM54331-32
Fluid temperature
Fig. 8
8
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
TUBE SIZE FLANGE LIQUIDS VIC GASES MIN. PSIA 'P [5] METER TUBE/FLOAT
& LENGTH SIZE GPM,LIQ.,SP. GR. [1] SCFM, AIR @STP [2] [3] [4] Inches
1.0 Water
1/2” - 250mm 1/2” & 1” 0.12 - 0.15 6 0.53 - 0.60 58 17 15 32 15-250-K 30
(with Orifice) 1/2” & 1” 0.17 - 0.19 6 0.70 - 0.81 58 17 15 32 40
1/2” & 1” 0.19 - 0.24 6 0.80 - 1.00 58 17 15 32 50
1/2” & 1” 0.24 - 0.29 6 1.05 - 1.20 58 17 15 32 60
1/2” - 250mm 1/2” & 1” 0.34 - 0.37 16 1.45 - 1.57 44 23 15 16 15-250-L 80
(with Tapered 1/2” & 1” 0.42 - 0.46 16 1.81 - 1.96 46 23 15 18 100
cone) 1/2” & 1” 0.51 - 0.55 16 2.17 - 2.36 51 23 15 20 120
1/2” & 1” 0.63 - 0.69 16 2.71 - 2.94 55 23 15 24 150
1/2” & 1” 0.83 - 0.93 16 3.54 - 3.99 58 23 15 24 15-250-S 200
1/2” & 1” 1.03 - 1.17 16 4.43 - 5.00 61 26 15 26 250
1/2” & 1” 1.24 - 1.40 16 5.31 - 5.99 64 26 15 28 300
1/2” & 1” 1.66 - 1.87 16 7.08 - 7.99 67 29 15 30 400
1/2” & 1” 2.07 - 2.33 16 8.86 - 9.99 70 31 15 30 500
1/2” & 1” 2.49 - 2.80 16 10.65 - 11.96 73 32 15 32 600
1/2” & 1” 3.30 - 3.74 16 14.13 - 16.02 78 35 15 34 800
1” - 250mm 1” 1.2 - 2.9 13 - 21 5.3 - 12.4 42 - 45 35 - 44 8 - 31 250-1.050 -S
1” 1.7 - 3.8 7-10 7.4 - 16.4 44 - 49 33 - 36 11 - 33 -N
1” 2.9 - 7.5 16 - 22 12.3 - 32.2 48 - 62 23 - 35 8 - 31 250-1.113 -S
1” 4.3 - 10.4 8 - 10 19.0 - 44.7 48 - 77 28 - 31 11 - 33 -N
1” 7.3 - 17.7 17 - 26 31.1 - 75.8 61 - 93 25 - 28 8 - 31 250-1.263 -S
1” 11.4 - 27.2 8 - 10 48.7 - 116.3 75 - 116 23 - 26 11 - 33 -N
2” - 250mm 1-1/2” & 2” 18.6 - 53.4 21 - 38 79.5 - 228.6 45 - 65 23 - 25 4 - 25 250-1.330 -S
1-1/2” & 2” 35.0 - 81.3 13 - 17 149.6 - 347.8 55 -90 26 - 32 10 - 30 -N
1-1/2” & 2” 51.8 - 106.6 3-4 221.6 - 456.5 64 - 109 29 - 38 11 - 29 -X
3” - 250mm 3” 30.8 - 92.5 22 - 54 131.9 - 395.9 49 - 78 20 - 29 2 - 19 250-1.315 -S
3” 79.7 - 154.2 18 - 25 340.9 - 659.4 70 - 107 23 - 46 10 - 26 -N
3” 117.8 - 236.9 4-5 504.1 - 1014.5 87 - 113 35 - 58 10 - 27 -X
4” – 250mm 4 110.0 - 220.0 60 – 81 471.1 - 942.2 58 – 87 12 - 30 250-1.310 -S
4 220.0 - 528.0 24 942.2 - 2261.0 102 - 130 17 - 38 250-1.310 -N
Notes:
The maximum flowrate can be adjusted between the values shown under either liquids or gases.
Flange sizes are for non-jacketed meters. Sizes greater than shown are possible upon request.
[1] Viscosity Immunity Ceiling (V.I.C.) must be greater than fluid viscosity (cps) times square root of the specific gravity. (V.I.C = CPS x ÖS.G.)V.I.C. is proportional
to the maximum flow rate.
[2] Minimum static pressure to avoid float bounce. Proportional to maximum flow rate.
[3] Minimum required pressure when using twisted guide rod. Size 1/2" only. Not available with Teflon lined meters.
[4] Minimum required pressure when using gas damping. Sizes 1/2" to 3" only. Proportional to maximum flowrate. Not available with Teflon lined meters.
[5] Pressure drop is proportional to maximum flow rate.
9
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
ORDERING INFORMATION
Armored VA Meter AM543 __ 2 F A 1 __ __ __________
10
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
Material Certification
Without ....................................................................................................... A
Material Certificate EN 10204-3.IB ............................................................. B
Other .......................................................................................................... Z
Float Design
Cylindrical Guide Rod w/o gas damping ............................................................ 1
Twisted Guide Road for gas damping (only 1/2" tube) ...................................... 2
Cylindrical guide rod with piston gas damping ................................................... 3
Float Material
Standard Meter, 316-Ti Stainless Steel .................................................................... A
316-Ti Stainless Steel w/Hastelloy-C head ............................................................... B
Teflon (PTFE) design w/Hastelloy-C head ................................................................ C
Teflon (PTFE) ........................................................................................................... D
Temperature Range
Standard Temperature ..................................................................................................... 1
Accuracy
± 2.5% max. flow - Teflon lined meters ................................................................................................. 1
± 1.6% max. flow - Unlined meters ........................................................................................................ 2
± 4% of max. range (viscosity effect calculation) (See Note 1) ............................................................ 3
Calibration, ± 1% max. flow, unlined meters ......................................................................................... 2
Instrument Tag
Adhesive ........................................................................................................................................................ B
Stainless Steel ............................................................................................................................................... E
11
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
Alarm Relays
AM54372 or AM54373 - SPDT - 110Vac, KFA5 - SR2 - Ex.1.W (163A012U01)
NOTES:
1. Viscosity calculations can be made for fluids up to 150 cps in unlined meters only
12
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
L D
k
Ansicht/V
iewX
R0.5
AnzahlderLöcher
N
NumberofBoltHoles
Gewindebuchse
ThreadedBushing
1/2”NPT
Schutzleiter
ProtectiveConductor
+1.0
-3.0
+1.0
-3.0
Kabeldurchführung
M20x1.5
145
H
CableConduit
A
X nur/only
AM54_32
Stopfen
Plug M25x1.5
B
94 C G
nur/only
AM54_71
Fig. 11 - Dimensions and Connections for Installation Length 250 mm (Standard Design)
H = Installation length with gas damping Comments: Installation length for PTFE lined flowmeters
1 / DN 25 PN 40 = 260 mm; 2 & 3 /
DN 50 + 80 PN 40 = 375 mm. Other upon request.
13
Variable Area Flowmeters
Armored Variable Area Flowmeters- Series AM54 D-FV-AM54_1
L D
k
Ansicht/V
iewX
R0.5
AnzahlderLöcher
N
NumberofBoltHoles
Gewindebuchse
ThreadedBushing
1/2”NPT
Schutzleiter
ProtectiveConductor
+1.0
-3.0
+1.0
-3.0
Kabeldurchführung
M20x1.5
145
H
CableConduit
A
X nur/only
AM54_32
Stopfen
Plug M25x1.5
B
94 C G
nur/only
AM54_71
Fig. 13
Meter Pressure
Size Rating
PN DN D k L N A B C G R
2” CL 150 1-1/2” 127.0 98.4 15.9 4 375.0 41.5 102 130 92.0
CL 300 1-1/2” 155.3 114.3 22.2 4 375.0 41.5 102 130 92.0
40 50 165.0 125.0 18.0 4 375.0 41.5 102 130 92.0
64 50 180.0 135.0 22.0 4 387.0 47.5 102 130 92.0
CL 150 2” 152.4 120.6 19.0 4 375.0 41.5 102 130 92.0
CL 300 2” 165.1 127.0 19.0 8 375.0 41.5 102 130 92.0
BS 10 Tbl. D 2” 152.4 114.3 17.5 4 375.0 41.5 102 130 92.0
3” 40 80 200.0 160.0 18.0 8 375.0 41.5 132 144 127.0
63 80 215.0 170.0 22.0 8 383.0 49.5 132 144 127.0
CL 150 3” 190.5 152.4 19.0 4 375.0 41.5 132 144 127.0
CL 300 3” 209.5 168.3 22.2 8 375.0 41.5 132 144 127.0
BS 10 Tbl. D 3” 184.0 146.0 17.5 4 375.0 41.5 132 144 127.0
ABB has Sales & Customer Support The Companys policy is one of continuous product
expertise in over 100 countries worldwide improvement and the right is reserved to modify the
information contained herein without notice.
www.abb.com
Printed in USA (05.13.03)
© ABB 2003
Warminster Cambridgeshire
PA 18974 PE19 8EU
USA UK
Tel: +1 215 674 6000 Tel: +44 (0)1480 475321
Fax: +1 215 674 7183 Fax: +44 (0)1480 217948
14