Professional Documents
Culture Documents
Sonialvision Safire
Sonialvision Safire
O P E R A T I O N G U I D E
Notation
The following notation is used in this operation guide.
Notation Meaning
● Denotes the contents of the operation
1, 2, 3 … Denotes the contents of the operation step by step
Denotes the consequences of the operation
Caution Denotes a special notice of the operation
Note Denotes the information which helps operation
Denotes points and notices of the operation
System Overview........................... 4
Configuration................................................................ 4
Diagnostic table console .............................................. 5
1
X-ray high voltage generator console .......................... 6
Digital image processor main screen........................... 6
Operation flow chart..................................................... 7
Fluoroscopy/Radiography .......... 16
Setting radiography condition .................................... 16
Radiography............................................................... 17
4
· SPOT radiography/SERIAL radiography …… 17
· DSA radiography (Option) …………………… 18
· Digital tomography (Option) …………………… 19
M517-E077A
1 System Overview
Configuration
Diagnostic table
X-ray
Control cabinet tube unit
(Flat panel detector)
Control cabinet
(X-ray high voltage generator)
Control cabinet Automatic
(Diagnostic table) collimator
Image monitor
Exposure switch
Mouse
Diagnostic table console
Keyboard
Selector
(attached mouse,
monitor and keyboard)
PCU
Foot switch (FPD control)
Control cabinet
(Digital image processor)
4 M517-E077A
L1 - L4 R1 - R4 Exposure indicator
Selects the magnification Selects the APR.
size of FPD. Exposure switch
Adjusts the
brightness of image.
F1 - F5 Joystick
Sets up the Subdivisional Acquisition
for SPOT radiography.
Sets up the tomography parameter
for tomography (Option).
M517-E077A
5
Downloaded from www.Manualslib.com manuals search engine
1 System Overview
Power ON button
+5
Power OFF button
0
Hand switch
-5
Patient
information
Standard control
panel
Standard control
panel/thumbnail
display button
Expanded control
panel
6 M517-E077A
Fluoroscopy/Radiography P.17
∗ Repeat as required.
M517-E077A
7
Downloaded from www.Manualslib.com manuals search engine
2 System startup and shutdown
Startup
1 Verify
● Image monitor of digital image
processor and peripherals are turned
OFF.
2 Press
will be illuminated after approx.
2 seconds.
1
Stand-by indicator
2 3
-5
8 M517-E077A
Shutdown
Press OFF.
ON lamp is turned off, and then
+5
-5
After pressing the OFF button on the X-ray high voltage generator
Caution console, do not press the ON button for at least 10 seconds. If you
do, the system may not operate properly.
M517-E077A
9
Downloaded from www.Manualslib.com manuals search engine
2 System startup and shutdown
FPD calibration
This operation maintains the quality of fluoroscopy/radiography images. Be sure to perform
the FPD calibration once a day after system startup. Verify that no substance is located on
the diagnostic table during FPD calibration. Approx. 15 minutes is required to complete the
FPD calibration.
Auto FPD calibration on system startup
console
The diagnostic table moves to
calibration position.
Press [F5 : SET] to move Table to
[SET]
10 M517-E077A
3 Click [Start]
An FPD Calibration starts.
[Close] button appears when FPD
calibration is complete.
4 Click [Close]
M517-E077A
11
Downloaded from www.Manualslib.com manuals search engine
2 System startup and shutdown
1 Right-click
image area
on the main
12 M517-E077A
3 Enter study
3 Click [Open]
The Patient Information window is
closed, and then the study starts.
A patient’s information appears on
the upper left corner of main image
area.
M517-E077A
13
Downloaded from www.Manualslib.com manuals search engine
3 E n t e r s t u d y
• Sex: OTHER
14 M517-E077A
M517-E077A
15
Downloaded from www.Manualslib.com manuals search engine
4 Fluoroscopy/Radiography
4 Fluoroscopy/Radiography
R1 - R4
1 Select APR
Diagnostic table console
Press any key of R1 - R4 on the
console to select APR.
16 M517-E077A
Radiography
Set the radiography condition prior to radiography as necessary.
3 Fluoroscopy
1 Verify that the fluoroscopy selection Note
switch illuminates. Confirm the [IBS] and [Pulse
The X-ray is not exposed when the Fluoroscopy] are selected
fluoroscopy selection switch is on touch panel of X-ray high
not illuminated even if the foot switch voltage generator console
is pressed. Press the fluoroscopy ([IBS] lights up when ON).
selection switch to light.
2 Press down the foot switch.
The exposure indicator illuminates. IBS Pulse Fluoroscopy
The fluoroscopy image appears on the
main image area of digital image processor.
M517-E077A
17
Downloaded from www.Manualslib.com manuals search engine
4 Fluoroscopy/Radiography
3 Fluoroscopy
1 Confirm that the fluoroscopy selection switch illuminates.
The X-ray is not exposed when the fluoroscopy selection switch is
not illuminated even if the foot switch is pressed. Press the fluoroscopy
selection switch to light.
2 Press down the foot switch.
The exposure indicator illuminates.
The fluoroscopy image appears on the main image area of digital image
processor.
4 Prepare injector
5 ExposePress and hold down the hand switch.
Mask images followed by live images are acquired (automatically).
The DSA image appears on the main image area of digital image processor.
X-ray exposure terminates after images are acquired within preset time.
Releasing the exposure switch stops the image acquisition during
exposure.
18 M517-E077A
3 Set up parameters
1 To select a parameter,
press [F2: Select].
2 To change the value,
press [F3: Value] or [F4: Value].
The exposure time is automatically
determined when the diagnostic table
moves to the starting point of tomography.
TEST
RUN
5 Exposure
Press and hold down the hand switch.
The tomography image appears on the main image area after each exposure.
Hold down the hand switch until the table stops.
When the hand switch is released during the process, the images for which the
exposures have been completed are stored on the hard disk.
M517-E077A
19
Downloaded from www.Manualslib.com manuals search engine
5 Process images
5 Process Images
Printing images
Do one of the following to print images.
Click [Print Image] : Confirm the actual image displayed on the main image area and
print the image.
Select from right-click menu: Confirm the actual image on the main image area and
select/deselect to print the image.
Select from Patient List: Entire patient file or specific study can be printed.
1 Click
Note
Printed images are saved in the "Print ShotSave" folder.
20 M517-E077A
1 Right-click
image area
on the main
M517-E077A
21
Downloaded from www.Manualslib.com manuals search engine
5 Process images
1 Click on the
Standard control panel
The Patient List window appears.
2 Select
study
patient file or
Patient
Print Print
Study Patient
5 Click [OK]
All images are printed.
22 M517-E077A
For manual DICOM send, open the patient file including image and allow that image to be
displayed on the main image area.
1 Click on the
Standard control panel
The DICOM menu appears.
M517-E077A
23
Downloaded from www.Manualslib.com manuals search engine
6 C l o s e S t u d y
6 Close Study
1 Standard
Click on the
control panel
A confirmation dialog appears.
2 Click [OK]
The patient file is closed.
24 M517-E077A
7 Troubleshooting
Emergency stop/Recovery
M517-E077A
25
Downloaded from www.Manualslib.com manuals search engine
7 Troubleshooting
Error messages
• X-ray high voltage generator console
When the system detects a fault, an error message appears on X-ray high voltage
generator console.
Touch the key to close the message screen, and then take action described
below for the error message.
(fault indicator) on the console illuminates and one of the following error messages
appears.
The system cannot expose while these messages are displayed.
Message Meaning Procedure
Radiography tube current
Radio Over Current exceeded set value
+ 200 mA.
Abnormal connection to
H. V. T Not Connected
high-voltage transformer.
26 M517-E077A
Increase radiography
Emission characteristics out
Emission OVER tube voltage or reduce
of range.
radiography tube current.
M517-E077A
27
Downloaded from www.Manualslib.com manuals search engine
7 Troubleshooting
T h e fl u o r o f o o t s w i t c h
Fluo switch ERR
remains ON.
Other messages
(caution indicator) on the console illuminates and one of the following error
messages appears.
The system cannot expose while these messages are displayed.
Message Meaning Procedure
28 M517-E077A
M517-E077A
29
Downloaded from www.Manualslib.com manuals search engine
7 Troubleshooting
Note
Battery backup time by UPS is approx. 3 minutes.
It sounds beep from control cabinet while the power is being backed up by UPS.
If the power fails because backup time for UPS expires, call a Shimadzu service
representative.
30 M517-E077A
KYOTO OFFICE
1, Nishinokyo-Kuwabaracho, Nakagyo-ku, Kyoto
604-8511, Japan.
Cable Add.: SHIMADZU KYOTO
Overseas Telex No.: 05422-166 (SHMDS J)