2022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
Clean And Clear: How To Measure Piston-
To-Valve Clearance
8 by JEFF SMITH JANUARY 13,2015
Text & Photos: Jeff Smith
a
Checking piston-to-valve (P to V) clearance isn’t
difficult, but necessary especially when building a
high performance engine with a big cam with lots
of lift. Building a custom engine means you must
make sure those valves will clear the pistons.
This is the golden age of horsepower and among big changes that are leading this charge are better
cylinder heads and more aggressive cam lobes. Big cams mean towering valve lift numbers. In the
most recent Engine Masters contest, all five top finalists ran no less than 0.750-inch lift and some
‘exceeded 0.850! Not too long ago, those might have been NHRA Pro Stock numbers.
Clearly, as cylinder heads improve flow capacity, valve lift will continue to escalate. As lift escalates
and combustion chambers get smaller, piston-to-valve (P to V) becomes tighter. The way to find out
that your valves don't clear the pistons is not when the engine locks up from a bent valve.
EMAIL ME
hitps:lwwu streetmusclemag,comech-slores/lean-clear-measure-piston-vave-clearancel a92002-00415 21:4 Clean And Clear: How To Measure Pston-To-Valve Clearance
Let's start with a quick run through of what's happening inside your engine. In the closing stage of
the exhaust stroke when the piston nears top dead center (TDC), the exhaust valve is closing while
the intake is just opening. This is commonly referred to as overlap. Think of this as the piston chasing
the exhaust valve closed while the intake valve opens into the piston.
So first we should establish what makes up minimum P to V clearance. In the past, the standard safe
clearance recommendation for most street engines was 0.100-inch for the intake valve and 0.140-
inch for the exhaust, The exhaust valve clearance is generally spec’d wider because if at high rpm
the exhaust valve bounces off its seat at closing, it's possible it could smack the piston. So added
clearance is necessary. If engine speeds are not high and the engine builder is confident that the
valve train can be controlled, then tighter clearances are possible down to perhaps 0.070-inch on the
intake and 0.100 on the exhaust. But as engine speeds increase, wider clearances can keep you out
of trouble.
Before measuring for P to V, it’s best
to know exactly where the cam is
positioned, which means you must
degree the cam so you know its
centerline position. Here, we are
using one of Comp’s professional
degree wheels, which is larger and
therefore more accurate.
hitps:lwwu streetmusclemag,comech-slores/clean-clear-measure-piston-vave-cearancel 2102002-00415 21:4 Clean And Clear: How To Measure Pston-To-Valve Clearance
According to the Reher & Morrison engine building and blueprinting book, it recommends a more
precise rule for calculating intake P to V is total deck clearance plus 0.010-inch. So with a steel
connecting rod total piston-to-head clearance of 0.040-inch, then 0.040 + 0.010 = 0.050-inch for the
intake valve. On the exhaust side R&M recommends 1.6 to 2 times the intake clearance. This makes
the exhaust side 0.100-inch or 0.080 if you're brave, These recommendations are more specific and
take into account aluminum connecting rods versus steel by using deck clearance. R&M
recommends a total deck clearance of 0.035 to 0,040 for steel rod engines and 0.055 to 0.070 for
aluminum rod applications. These are general recommendations and certainly will vary with more
specific builds, but these numbers are a great place to start for a strong street engine.
What to Do First
Before we begin to measure P to V clearance, we first must be certain of where the camshaft is in
relation to the pistons. Each cam manufacturer will recommend a specific position for the cam based
on the intake centerline. This position tends to be the most accurate way to locate the cam. For
‘example, the cam card will list the intake centerline as 108 degrees after top dead center (ATDC).
We won't go into the procedure for degreeing a camshaft as that subject has been well covered.
If you are considering changing the intake centerline by either advancing or retarding the cam, you
will need to perform the P to V measurements at all of the considered intake centerlines. Advancing
the cam moves all the valve events earlier, which would reduce the intake V to P clearance and
increase the exhaust. Retarding the cam will do the opposite.
The Clay Method
If your engine uses hydraulic
tappets, you will need to
substitute a mechanical lifter to
ensure accurate valve lift. You
can create a solid checking
lifter out of an old hydraulic
lifter (either flat or roller) by
removing the internal hydraulic
piston and shimming the
pushrod cup in place with
hitps:lwwu streetmusclemag,comech-slores/lean-clear-measure-piston-vave-clearancel ano2022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
small washers. This will create
an accurate lift curve for
measuring P to V.
Make sure you use a
compressed head gasket, or i
the gasket is new you will need
to fully torque the head in
place. With a used gasket, full
torque is not necessary, Retain
the head with at least five head
bolts torqued to 50 ft-lbs to
load the head properly.
If your engine uses hydraulic tappets, you will need to substitute a mechanical lifter to ensure
accurate valve lift. You can create a solid checking lifter out of an old hydraulic lifter (either flat or
roller) by removing the internal hydraulic piston and shimming the pushrod cup in place with small
washers. This will create an accurate lift curve for measuring P to V[/caption]
Let's start with the easiest method for determining P to V, but only if the heads are already off the
engine. Frankly, the only specialty tool needed is some modeling clay — which you can borrow from
your kid's toy box. Place roughly a 3/8-inch thick lump of clay in the piston intake and exhaust valve
reliefs.
Lightly coat the valve faces with oil to prevent the clay from sticking to the valves. Now assemble the
heads with a previously compressed head gasket. The most accurate test is to fully torque the entire
head, but we generally only torque the head bolts around the cylinder in question
If your engine is equipped with hydraulic lifters, these will compress under load, so the best
procedure is to substitute a set of mechanical lifters. Assemble the intake and exhaust pushrods and
rockers and then set the lash at zero if you're using a hydraulic cam. If the cam is mechanical, set
the lash at the adjusted hot setting as specified in the accompanying chart. Iron does not expand as
much as aluminum so these changes to cold lash are based on the thermal expansion rates of
aluminum versus iron, making the lash clearances a bit closer to the hot settings.
hitps:lwwu streetmusclemag,comech-slores/clean-clear-measure-piston-vave-cearancel anoClean And Clear: How To Measure Piston-To-Valva Clearance
With clay in place over the valve reliefs, rotate the engine several times, Note that
the valves have created a depression in the clay that we've cut in half with a razor.
In this case, the depth clearance was 0.220-inch for the intake but only about
0.090-inch for the exhaust. Also note that the radial clearance for the intake
appears to be tight - it is difficult to measure but appeared to be about 0.080-inch.
This may require more accurate measurement.
Once lash is set for both the intake and exhaust valves, you can now carefully roll the crankshaft
over at least four revolutions to allow the valves to run through their entire lift cycles. With that
complete, disassemble the valvetrain and remove the cylinder head and bring the piston up to TDC.
You will notice that the valves will have pushed into the clay, revealing the amount of clearance.
There are several ways to measure this, You can use a dial caliper to measure the depth or you can
cut the clay in half with a razor blade and then use a dial caliper to measure this depth
If you look carefully, the clay may also indicate the radial clearance between the valve pockets and
the valve although often this can be difficult to measure accurately. Most street piston manufacturers
will place more than adequate valve reliefs in their pistons so that machining is not required.
There are several limitations to this procedure. First, itis not highly accurate, although this is only
necessary when the clearances are very near the minimum. Most street engines end up with over a
0.250-inch of P to V clearance, which means accuracy isn't critical. As mentioned, radial clearance —
the clearance between the outside diameter of the valves and the piston reliefs is important. We
talked to engine builder Kurt Urban, and he prefers 0.060 just to be safe because engines with really
short skirt pistons can move around quite a bit. We will run through how you can measure for this
clearance in a moment using a homemade tool and a dial indicator.
hitps:lwwu streetmusclemag,comech-slores/clean-clear-measure-piston-vave-cearancel sno2022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
The Dial Indicator Method
If you do not want to remove the heads, you can still
check P to V by using a dial indicator, magnetic base, and
checking springs on both valves. Place the indicator
plunger on the valve spring retainer (Intake shown here).
Rotate the engine to place Number One piston at 10
degrees ATDC. Zero the dial indicator at this valve lift and
use the rocker to open the valve until it contacts the
piston. The amount of additional lift displayed on the dial
indicator is the intake P to V clearance. You may want to
rotate the crank 5 degrees on either side of 10 ATDC to
find the tightest spot.
If removing the heads from the engine is not practical, you can measure P to V with a couple of
checking springs and a dial indicator. First, remove all the spark plugs and install light checking
springs on Number One intake and exhaust. Next, determine exactly where TDC is with a degree
wheel because you will need to place the piston 10 degrees before and after TDC. Once this is
established, set up the dial indicator on the exhaust valve to measure valve lift from the spring
retainer, Slowly rotate the engine clockwise by hand until the piston is 10 degrees BTDC. The
exhaust valve will be on the closing side of its lift curve. Zero the dial indicator and then push down
on the valve end of the rocker and record the amount of travel before the exhaust valve contacts the
piston. This amount of movement is the P to V for the exhaust valve. Now rotate the engine to 10
degrees ATDC and move the dial indicator to the intake valve. Zero the dial indictor and then
depress the intake valve with the rocker until it too hits the piston. Record this value as the intake
clearance,
IfP to V clearance is close to or at the minimum, you may want to consider performing this test again
except with the intended valve spring package. High spring pressures will create deflection in the
valve train that can change the P to V. This test will also require some kind of lever tool to compress
the spring once it is in position.
hitps:lwwu streetmusclemag,comech-slores/lean-clear-measure-piston-vave-clearancel eno2022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
Checking Radial Clearance
If the outside diameter of the valve appears to be close to the edge of the piston valve relief, this will
require more accurate measurement. The important measurement is the valve centerline relative to
the valve relief in the piston. We found this trick in the Reher & Morrison Engine Building book where
David Reher recommends cutting the head off of a valve and having a machinist mill one end to a
point. Then with the piston at TDC and the head in place, use the valve stem to mark the valve
centerline in the piston. As an example, let's use an LS engine with 2.165-inch intake valves.
Dividing the valve diameter in half to establish the radius, this gives us a radius of 1.0825. Duplicate
this distance on a pair of dividers and then scribe a radius from the piston centerline. If there is less
than 0.050 to 0,060 inch between the scribed line and the vertical wall of the valve pocket, this will
require machining to increase the clearance. If the clearance is more than 0.050 — the clearance is
good and you're ready for assembly.
If the clay method indicates tight radial valve clearance,
you may want to perform a more accurate measurement.
Cut the head off a used valve (we used a cut-off wheel)
and have a machinist mill the stem to create a point. Or if
you have a set of transfer punches, we found they work
equally well. Set the piston at TDC and use the transfer
punch to lightly mark intake and exhaust centerlines.
Taking the time to measure P to V cannot be over-emphasized. It's also the kind of thing that all good
professional engine builders do as a matter of course. While these procedures may seem
intimidating at first, they are simple to perform and worth the time it takes — if nothing else just for
insurance against disaster
hitps:lwwu streetmusclemag,comech-slores/lean-clear-measure-piston-vave-clearancel 7H02022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
Using the valve centerline marked in the piston, set the valve radius (half of valve
diameter) with a set of dividers and scribe a radius around the valve relief. This
will indicate if you have sufficient radial clearance. If not, the pocket may need to
be machined.
Valve Lash Compensation Table
For accuracy with a cold engine and a solid lifter camshaft, this chart specifies compensation for heat
expansion with cold lash settings. With an iron block engine with aluminum heads, the chart
recommends subtracting 0.006-inch of lash from the recommended hot settings. This will increase
valve lift and decrease P to V by that amount.
Lash Compensation
Block Head (inches)
Iron Iron +0.002
Iron Aluminum — -0.006
Aluminum = Aluminum —-0,012
Parts List
Description PN Source Price
Checking Springs, pair 4758-2 Summit Racing $3.97
Professional degree wheel 4791 Summit Racing 190.97
hitps:lwwu streetmusclemag,comech-slores/clean-clear-measure-piston-vave-cearancel ano2022-09-16 21:24
Caliper, 6 inch
Dial Indicator magnetic base
Dial Indicator, 0-1" travel
Reher & Morrison Racing book
Sources
COMP Cams
(800)999-0853
compcams.com
Reher-Morrison Racing Engines
(817/467-7171
rehermorrison.com
Clean And Clear: How To Measure Piston-To-Valva Clearance
4908
4907
4909
Order Online
Summit Racing
‘Summit Racing
Summit Racing
Reher & Morrison
hitps:lwwu streetmusclemag,comech-slores/lean-clear-measure-piston-vave-clearancel
49.97
67.97
37.97
74.95
sno2022-09-16 21:24 Clean And Clear: How To Measure Piston-To-Valva Clearance
ABOUT THE AUTHOR
Jeff Smith
Jeff Smith, a 35-year veteran of automotive journalism, comes to Power Automedia afer serving as the
senior technical editor at Car Craft magazine. An lowa native, Smith served a variety of roles at Car Craft
before moving to the senior editor role at Hot Rod and Chevy High Performance, and ultimately returning to
Car Craft. An accomplished engine builder and technical expert, he will focus on the tech-heavy content
that is the foundation of EngineLabs.
READ MY ARTICLES
r0n0