POLYSTAR UG-23 is an ortho type unsaturated polyester gel-coat resin intended for use in producing fishing boats and general fiberglass reinforced plastic products. It has good weather resistance, pigment dispersion, impact strength, and sprayability. When cured it has tensile and flexural strengths between 6.3-7.3 kg/mm2 and 11.5-12.7 kg/mm2 respectively. Proper handling and safety precautions should be followed when using this product.
POLYSTAR UG-23 is an ortho type unsaturated polyester gel-coat resin intended for use in producing fishing boats and general fiberglass reinforced plastic products. It has good weather resistance, pigment dispersion, impact strength, and sprayability. When cured it has tensile and flexural strengths between 6.3-7.3 kg/mm2 and 11.5-12.7 kg/mm2 respectively. Proper handling and safety precautions should be followed when using this product.
POLYSTAR UG-23 is an ortho type unsaturated polyester gel-coat resin intended for use in producing fishing boats and general fiberglass reinforced plastic products. It has good weather resistance, pigment dispersion, impact strength, and sprayability. When cured it has tensile and flexural strengths between 6.3-7.3 kg/mm2 and 11.5-12.7 kg/mm2 respectively. Proper handling and safety precautions should be followed when using this product.
POLYSTAR UG-23 is Ortho type Unsaturated -3 month polyester Gel-coat resin. - Do not leave the Resin at the place of direct sunlight or heat. 2. Use POLYSTAR UG-23 is Ortho type Gel-coat for 7. Caution Rules at Hardening the production of Fishing Boat and General FRP - The Gel-time is a change working conditions products. (ex. temperature, humidity). Please adjust amount of hardener & promoter according to 3. Distinguishing Characteristics working conditions, before use. - Good Weather Resistance. - The hardener amount is appropriate 1% of resin for suitable hardening. - Good pigment Dispersion. - As hardening can be delayed according to - Excellent Impact Strength work temperature, you should use it in proper temperature. - Good Sprayabilyty.. 8.Caution Rules at Use 4. Typical Properties:Liquid Resins * - Keep it at the place that can cut off heat, Units Spec Remarks light. Please pay attention to firearms. Specific - As a hardener can explode, Please keep it at 25℃ 1.08-1.12 the place that can avoid the heat, a shock, A gravity direct sunlight. Viscosity Poise/25℃ 15 – 45 #4, 60 rpm - If hardener and promoter come directly in Thixotropic - 3.8 – 5.0 6/60 rpm contact, they can explode. You should not MEKPO 1.0 phr keep together at all it. Gel-time Min 6 - 18 at 25℃ - Put on gloves and a mask when you work. * Values are representative. - Ventilate a workplace at any time. Specification limits are available upon request. - After use, residual resin should seal. (Water, dust get into the resin or Styrene 5. Typical Properties: Cured Resin *1 monomer evaporates, and the resin can be Units Results Remarks degenerated.) Tensile Strength ㎏/㎟ 6.3-7.3 - Styrene uses below 3percents in order to ASTM D 638 adjust viscosity. Tensile Modulus ㎏/㎟ 330-370 - Please use the amount that use is possible Elongation % 2.0-3.0 only within work time. Flexural Strength ㎏/㎟ 11.5-12.7 - If the resin or a hardener get into worker’s ASTM D 790 Flexural Modulus eyes, Please wash eyes immediately more ㎏/㎟ 320-353 than 15 minutes with running water and get ASTM D 2583 Barcol Hardness - 38-42 from prescription of a doctor. ASTM D 648 HDT ℃ 70-82 ASTM D 570 Water absorption % 0.1 *1. Thickness : 3 mm Catalyst : 55% MEKPO 1.0 phr Post Cure : 25C 6hrs, 80C 4hrs 169, Taehwa-Dong, Daeduk-Gu, Taejon, R.O Korea TEL)042-625-2541 FAX)042-634-7543 . For more information regarding safe & health, please refer MSDS providing in our companies.
The company cannot accept liability for use the technical data for anything other than reference.