Professional Documents
Culture Documents
B0860ru K
B0860ru K
FERRET v6.4
Installation and Release Notes
*B0860RU* *K*
B0860RU, Rev K
November 2019
www.schneider-electric.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and furnished
for informational use only. No part of this guide may be reproduced or transmitted in
any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise), for any purpose, without the prior written permission of Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as is"
basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
FERRET v6.4 Installation and Release Notes
Table of Contents
Preface ...............................................................................................................5
Workstation Types............................................................................................5
Revision Information.........................................................................................5
Related Documents..........................................................................................5
Schneider Electric Products Mentioned in this Document ....................................6
Global Customer Support .................................................................................6
We Welcome Your Comments...........................................................................6
Chapter 1: Overview ........................................................................................7
Chapter 2: Enhancements ..............................................................................8
New Station Manager Screen for Remote Collection ...........................................8
FERRET Now Collects Master Timekeeper Information ......................................8
FERRET Now Collects Device Monitor Information .............................................8
Chapter 3: Installation Prerequisites..............................................................9
Systems with Security Enhanced I/A Series Software v8.5 to v8.7........................9
Systems with Security Enhanced I/A Series Software v8.5 to v8.7 and v8.8 or
Control Core Services v9.x................................................................................9
Choosing the FERRET Host Station ................................................................10
Standard Data and Equipment Information.......................................................10
Splitting a Station Collection............................................................................ 11
Chapter 4: Installing FERRET ......................................................................12
Initial Installation ............................................................................................12
FERRET Installation.......................................................................................12
Chapter 5: Installing Off-Platform FERRET ................................................14
Off-Platform Installation ..................................................................................14
Appendix A: Issues Resolved .......................................................................15
B0860RU, Rev K 3
n k
Bla
ef t
y L
all
io n
n t
Inte
ge
P a
h i s
T
Preface FERRET v6.4 Installation and Release Notes
Preface
This document is intended for use by Field Service representatives. It provides
specific information and procedures for installing FERRET on EcoStruxure™
Foxboro™ DCS Control Core Services (CCS) workstations.
Workstation Types
Foxboro DCS Any workstation installed with an EcoStruxure™ Foxboro DCS
software component, including EcoStruxure Foxboro Control
Core Services, Foxboro DCS Control Software, Wonderware
Historian, I/A Series™ software, FCS, or any combination thereof.
Control Core Any Foxboro DCS workstation installed with Control Core
Services Services or I/A Series software. This workstation is connected to
the EcoStruxure™ Foxboro Control Network.
Non-Control Any Foxboro DCS workstation that does not have Control Core
Core Services Services or I/A Series software installed. This type of workstation
is not connected to the Control Network, but can have Control
Software installed on it.
Control Any Foxboro DCS workstation installed with Control Software
Software components, including Control Editors, Control HMI,
Wonderware Historian, or other components installed as part of
the Control Software. This workstation may or may not also be a
Control Core Services workstation.
Revision Information
For this revision of the document, the following changes were made:
Related Documents
In addition to the information presented herein, you should be familiar with the
following Foxboro DCS and I/A Series documents:
• FERRET v6.4 (Windows® Platforms) and FERRET v6.3.2 (UNIX® Platforms)
User’s Guide (B0860BU)
• The Foxboro DCS Control Network Architecture Guide (B0700AZ)
• Switch Configurator Application Software Guide for the Control Network
(B0700CA)
• System Asset Viewer v3.4 User's Guide (B0860BV)
Find the latest version of these documents on the Global Customer Support (GCS)
website.
B0860RU, Rev K 5
FERRET v6.4 Installation and Release Notes Preface
6 B0860RU, Rev K
Chapter 1: Overview FERRET v6.4 Installation and Release Notes
Chapter 1: Overview
For sites (Windows-based) workstations, these points provide an overview of the
installation process.
You can install FERRET for Windows software, v6.4 (FERRET) once on a single
workstation.
When FERRET is run, the software will propagate to the other workstations, at the site
including all stations with I/A Series software v8.x or Control Core Services software
(CCS) v9.x.
FERRET v6.4 no longer supports stations older than I/A 8.2.
We recommend that the station with the latest version of I/A Series software or
Control Core Services software available at the site be used as the install station
(Host station). This station is usually the CSA station. If you prefer not to use the CSA
station, you can install FERRET on a workstation with the closest version of I/A Series
software or Control Core Services software to that of the CSA.
For systems with legacy nodes (with I/A Series software v6.x or v7.x) connected using
an ATS in Extender mode (also referred to as a bridge node), you must use the legacy
version of FERRET (v6.3.1). Install the legacy version of FERRET on either the bridge
node or a workstation on the legacy Nodebus node. Otherwise, FERRET will be
unable to collect data from the legacy node. This is necessary if a second Ethernet
(entered using the second IP address on the FERRET Station Exclude screen) is not
available for at least one workstation on the legacy node.
Installation Procedures Include:
• Executing the software installation
• Validating the connectivity to Legacy Nodes
• Testing the installation
NOTE: FERRET v6.4 no longer supports Nodebus or UNIX collections. To collect
these legacy stations you must run a legacy version of FERRET.
B0860RU, Rev K 7
FERRET v6.4 Installation and Release Notes Chapter 2: Enhancements
Chapter 2: Enhancements
New Station Manager Screen for Remote Collection
FERRET now uses a new Station Manager screen for all remote collections. This
screen allows you to remotely connect to other workstations at site, install FERRET,
perform a collection, and uninstall FERRET.
The Station screens and most run options are now handled by the new Station
Manager screen.
8 B0860RU, Rev K
Chapter 3: Installation Prerequisites FERRET v6.4 Installation and Release Notes
B0860RU, Rev K 9
FERRET v6.4 Installation and Release Notes Chapter 3: Installation Prerequisites
Standard I/A Series • The host station should be the Windows station with the latest version of
software v8.5 or Control Core Services software
earlier
I/A Series Security • Install FERRET on the Security Enhanced station with the latest version of
Enhanced stations I/A Series software
v8.5 to v8.7 only
• Log in to the station using an account in the “I/A Plant Maintenance”
domain group
Security Enhanced • FERRET must be run from a workstation with I/A Series v8.8 or Control
stations with both I/A Core Services software v9.x
Series software v8.5 • Log in to the station using an account in the “I/A Series Plant Admins”
to v8.8 and Control domain group
Core Services
software v9.x • To remotely collect v8.5-v8.7 Security Enhanced stations, you must enter
a username/password for those stations on the “Station List” screen. The
account entered must be part of the “I/A Plant Maintenance” domain
group.
NOTE: Remote collection of Windows XP stations from Windows 10/
Server 2016 stations is not supported.
10 B0860RU, Rev K
Chapter 3: Installation Prerequisites FERRET v6.4 Installation and Release Notes
B0860RU, Rev K 11
FERRET v6.4 Installation and Release Notes Chapter 4: Installing FERRET
Initial Installation
1. Log on to the Foxboro® station:
• For stations with Foxboro DCS Security Enhanced/Enterprise software v9.x,
log in using an account in the “I/A Plant Admins” domain group.
• For a station with I/A Security Enhanced software v8.5 thru v8.7, log on using
an account in the “I/A Plant Maintenance” domain group. IAInstaller is a user
account in the Administrators group.
• For all other stations, log on using the standard Fox account.
2. Insert the CD (Foxboro Part No. K0174MD-H) into the CD drive.
3. Right click the Start button and select Explore.
4. Navigate to the CD Drive. (For example, E:\).
5. Execute the file FERRET.msi to start the FERRET installation.
6. Follow the installation dialog boxes. Refer to the FERRET Installation, page 12.
FERRET Installation
1. On the Welcome screen of the installation, click Next.
2. On the Ready to Install FERRET screen, click Install.
12 B0860RU, Rev K
Chapter 4: Installing FERRET FERRET v6.4 Installation and Release Notes
B0860RU, Rev K 13
FERRET v6.4 Installation and Release Notes Chapter 5: Installing Off-Platform FERRET
Off-Platform Installation
1. Log on to the Windows station: For all stations use an account in the “Users”
group.
2. Insert the CD (Foxboro Part No K0174MD-H) into the CD drive.
3. Right click the Start button and select Explore.
4. Navigate to the CD Drive. (For example, E:\.)
5. Execute the file FERRET.msi to start the FERRET installation.
6. Follow the installation dialog boxes. (See Chapter 4: Installing FERRET, page
12.)
14 B0860RU, Rev K
Appendix A: Issues Resolved FERRET v6.4 Installation and Release Notes
B0860RU, Rev K 15
Schneider Electric Systems USA, Inc.
38 Neponset Avenue
Foxboro, Massachusetts 02035–2037
United States of America