Professional Documents
Culture Documents
Christmas Tree and Wellhead Function Components Difference Design Codes With PDF
Christmas Tree and Wellhead Function Components Difference Design Codes With PDF
The Christmas tree consists of an assembly of a gate valve that controls the flow of
hydrocarbons. It may consist of individual valves bolted together or it may feature a cast
or forged steel solid block into which the valve chests are machined. Occasionally it is a
combination of the two. In all cases, the valve seats and gates are removable for
replacement or repair.
What is a Wellhead?
A wellhead skid controls the operation of the Christmas tree and mudline safety
valves. The skid permits valves to be operated locally, remotely, or via an ESD system,
and timing, mechanisms provide a means of controlling the speed and sequence of valve
operation. This sequence would normally be close to the wing valve, master valve, and
mudline safety valve.
During an ESD operation, complete closure of the Christmas tree valves should be
effected within approximately 45 seconds according to API recommendations, the only
organization to provide guidance on this particular aspect.
Wellheads can be Dry or Subsea completion. Dry Completion means that the well is
onshore on the topside structure on an offshore installation. Sub-sea wellheads are
located underwater on a special sea bed template. The wellhead consists of the
1/6
pieces of equipment mounted at the opening of the well to regulate and monitor the
extraction of hydrocarbons from the underground formation. It also prevents the
leaking of oil or natural gas out of the well and prevents blowouts due to high-pressure
formations. Formations that are under high pressure typically require wellheads that can
withstand a great deal of upward pressure from the escaping gases and liquids.
These wellheads must be able to withstand very high pressures of the order of 140
MPa (1400 Bar). The wellhead consists of three components: the casing head, the
tubing head, and the ‘Christmas tree’.
Advertisements
A tree may also be used to control the injection of gas or water injection applications on a
producing or non-producing well in order to sustain economic “production” volumes of gas
from other wells (s) in the area (field).
The control system attached to the tree controls the downhole safety valve while the tree
acts as an attachment and conduit means of the control system to the downhole safety
valve.
2/6
At the bottom, we find the Casing Head and casing Hangers. The casing will be screwed,
bolted, or welded to the hanger. Several valves and plugs will normally be fitted to give
access to the casing. This will permit the casing to be opened, closed, bled down, and, in
some cases, allow the flowing well to be produced through the casing as well as the
tubing. The valve can be used to determine leaks in the casing, tubing, or packer, and will
also be used for lift gas injection into the casing.
The tubing
hanger (also called donut) is used to position the tubing correctly in the
well.
Sealing also allows Christmas tree removal with pressure in the casing.
There are wells drilled into the reservoir, and the central conductor along with the
surrounding jackets/annulus rises up to the Production Deck / Cellar deck of the platform.
On top of the wellhead, an assembly of valves is placed, which has the form of a cross.
This assembly of valves together with the flanges is called a Well Head Christmas tree.
The Christmas tree has many Manual valves and a number of Actuated valves. The
actuated valves usually found on the Christmas tree are as follows:
The Sub-Surface Safety valve is a hydraulic operated valve, the location of which is
below sea level, above the sea bed. The actuator of this valve needs to be very small, as
it gets enclosed within the Annulus of the conductor. The actuator is usually hydraulically
operated. The control line for the hydraulic supply for the SSSV runs within the conductor
and terminates at a connection on the Christmas tree.
This isolates the tree from the production tubing. The Christmas tree has two master
valves referred to as the upper and lower master valves. The lower master valves are
opened first and closed last. This ensures a minimal flow of hydrocarbon over the valve
seat, thus protecting it from abrasive particles and ensuring a good seal is maintained.
In most cases, the lower master valve is manually operated and the upper master valve is
operated via a hydraulic or pneumatic actuator and is connected to the emergency
shutdown system. The actuators are fail-safe in operation. The valve is held open by oil
or pressure against a compressed coil spring.
The master gate valve is a high-quality valve. It will provide a full opening, which means
that it opens to the same inside diameter as the tubing so that specialized tools may be
run through it. It must be capable of holding the full pressure of the well safely for all
anticipated purposes. This valve is usually left fully open and is not used to control flow.
A master valve is the first actuated valve on the Christmas tree, located above the
Mezzanine deck of the platform. The Actuator is bigger and can be pneumatic or
Hydraulic, based on the Christmas tree requirement
3/6
The pressure gauge:- The minimum instrumentation is a pressure gauge placed above
the master gate valve before the wing valve. In addition, other instruments such as
temperature will normally be fitted.
3. Wing Valve:-
The wing valve comes on the arm of the Christmas tree, on the line where the flow line
starts. The actuator is again hydraulic or pneumatic based on the requirement. The wing
valve can be a gate valve or a ball valve. When shutting in the well, the wing gate or valve
is normally used so that the tubing pressure can be easily read.
Christmas trees may be manufactured with one or two wing valves. One valve is
permanently connected to the hydrocarbon process system and is fitted with a hydraulic
or pneumatic actuator. The other valve is manual in operation and permits the injection of
chemicals or gases into the well without disturbing production pipework.
Both valves are offset from the vertical lines so that a clear entry into the well s
maintained through the swab valve for wireline work. The flow of gas from the well is
regulated by wing valve operation or by choking fitted above the wing valve.
Hydraulic tree wing valves are usually built to be fail-safe closed, meaning they require
active hydraulic pressure to stay open.
The right-hand valve is often called the flow wing valve or the production wing valve
because it is in the flow path the hydrocarbons take to production facilities.
The left-hand valve is often called the kill wing valve. It is primarily used for the injection
of fluids such as corrosion inhibitors or methanol to prevent hydrate formation.
The Well Service Valve may be present on some Christmas trees, where Diesel pumping
is required for initial start-up. It is on the other arm of the Christmas tree, and usually, the
size is lesser than that of the wing valve.
The valve at the top is called the swab valve and lies in the path used for good
interventions like wireline and coiled tubing. A ‘Choke’ is a device, either stationary or
adjustable, used to control the gas flow, also known as volume, or create downstream
pressure, also known as back pressure.
The Wellhead valves are all controlled by a Well Head Control panel, which gives the
hydraulic & pneumatic supply for opening/closing these valves. There is logically built in
the WHCP for allowing the safe closure of all these wellhead valves, in case of an
emergency, either due to process upset or due to emergency/fire. In addition to these
valves, the other instrumentation which is associated with the Christmas tree is the
Pressure gauges and Transmitters for monitoring the Annulus pressures, the Flowing
Tube Head Pressure, etc.
4/6
Christmas Tree vs Wellhead?
In the complicated but vital industry of drawing oil and gas out of the earth and getting it
to the surface, people often get confused about the difference between a Christmas
tree assembly and a wellhead. Although the terms are used interchangeably, a
wellhead and a Christmas tree are entirely separate pieces of equipment. Each has
valves and related equipment that help it control and guide the flow of this precious
resource. A wellhead must be present in order to utilize a Christmas tree and is used
without a Christmas tree during drilling operations. Producing surface wells that require
pumps (pump jacks, nodding donkeys, etc.) frequently do not utilize any tree due to no
pressure containment requirement.
Basically, The
Christmas tree and the wellhead work together to bring oil and gas to the
surface.
A tree often provides numerous additional functions including chemical injection points,
well intervention means, pressure relief means (such as annulus vent), well monitoring
points (such as pressure, temperature, corrosion, erosion, sand detection, flow rate, flow
composition, valve and choke position feedback, connection points for devices such as
downhole pressure and temperature transducer.
5/6
nomenclature of parts used in describing the Christmas Tree and wellhead.
6/6