Professional Documents
Culture Documents
Revision 08/07/18
2001-'02
Toyota Corolla
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
please call Crutchfield Technical Support at 1-800-955-9094.
Inside...
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without
warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle
production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your
vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.
*0000530033*
Page
2. Set parking brake and disconnect negative battery cable to prevent any electrical short.
3. Pry around all edges of receiver trimpanel to release six (6) plastic clips. Disconnect wiring harnesses and remove receiver trimpanel (Figure 1).
4. Remove four (4) phillips screws securing factory radio. Pull out radio, disconnect and remove (Figure 2).
FIGURE 1 FIGURE 2
Factory Radio
Receiver Trimpanel
1-800-955-9094
TECHNICAL SUPPORT Copyright 2018 Crutchfield Corporation 3
053 0033 NOTES:
Please read first
• Check to make sure the Crutchfield receiver wiring
Receiver Installation (factory-equipped with CD changer) adaptor plugs into the vehicle receiver harness.
If the Crutchfield adaptor is incorrect, please call our
Technical Support Department at 1-800-955-9094.
2. Remove four (4) phillips screws securing factory radio to side brackets
(two screws on each side of radio - Figure 1).
3. Remove DIN sleeve and trim ring from new receiver (Figure 2).
Note: The sleeve and trim ring will not be used in this application.
4. Place new receiver inside factory side brackets. Align mounting holes
on replacement receiver with holes in factory side brackets (Figure 3).
Secure receiver in the same manner as factory radio using screws
supplied with new receiver.
6. Remove four (4) phillips screws (two on each side) securing factory side
brackets to CD changer. Secure brackets to side of replacement
pocket in the same manner. Insert pocket into upper dash space and
secure with screws that secured factory changer.
Side Bracket
FIGURE 1 (right side shown)
7. Test receiver operation and reassemble dash
by reversing removal steps.
FIGURE 2 FIGURE 3
! SAFETY CHECK Mounting Holes
Return gear shift to park position.
1-800-955-9094
TECHNICAL SUPPORT
DIN Sleeve
Trim Ring
Copyright 2018 Crutchfield Corporation 4
053 0033 NOTES:
Please read first
• Check to make sure the Crutchfield receiver wiring
Receiver Installation (vehicle not factory-equipped with CD changer) adaptor plugs into the vehicle receiver harness.
If the Crutchfield adaptor is incorrect, please call our
Technical Support Department at 1-800-955-9094.
1. Make wiring connections following instructions supplied with the receiver wiring
adaptor.
2. Remove four (4) phillips screws securing factory radio to side brackets (two screws
on each side of radio - Figure 1).
3. Remove DIN sleeve and trim ring from new receiver (Figure 2). Note: Sleeve and
trim ring will not be used in this application.
4. Place new receiver inside factory side brackets. Align mounting holes on
replacement receiver with holes in factory side brackets (Figure 3). Secure receiver
in the same manner as factory radio using screws supplied with new receiver.
5. Connect receiver wiring adaptor to vehicle harness and plug antenna lead into rear
of receiver. Secure receiver assembly to dash with screws previously removed.
FIGURE 1 FIGURE 2
Trim Ring
DIN Sleeve
FIGURE 3 FIGURE 4
Screws
! SAFETY CHECK Factory Speaker (supplied with brackets)
Check that wires do not interfere with window operation.
Test door lock and release operation. Screws
FIGURE 8
(supplied with speakers)
! CAUTION:
Always be careful when drilling or cutting in a vehicle. WEAR
EYE PROTECTION. Be aware of things such as wiring,
1-800-955-9094 windows, fuel lines and safety devices. Check depth and
TECHNICAL SUPPORT location to avoid damage to vehicle appearance. 7
Copyright 2018 Crutchfield Corporation
053 0033 NOTES:
Please read first
Rear Deck Speakers • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
1. Pry off child seat belt anchor covers (3). Remove one (1) 12mm bolt from
each anchor and remove anchors (Figure 1).
FIGURE 1 Anchor (3)
2. Pry out two (2) retaining clips from front edge of rear deck panel
(Figure 2).
3. Push front edge of brake light assembly toward rear window to release
two (2) clips. Lift assembly, disconnect wiring harness and remove
(Figures 3 & 4).
Retaining Clip
(1 of 2 shown)
1-800-955-9094
TECHNICAL SUPPORT Copyright 2018 Crutchfield Corporation 8
053 0033
FIGURE 6 FIGURE 7
! SAFETY CHECK
Make sure seats and seat belts are secured to
1-800-955-9094 manufacturer’s specifications.
TECHNICAL SUPPORT Check third rear brake light connection and test operation.
Copyright 2018 Crutchfield Corporation 9
053 0033
Wire Splicing Guide These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available.
Wire color information (if available) can be found on the next page.
Factory harness is removed. Save New speaker wires are spliced into
CRIMP METHOD harness if it is to be reconnected in
the future by this method.
SOLDER METHOD factory wires behind harness.
1. Cut factory wires behind 2. Strip end of each 1. Carefully strip out a 1/2” 2. Twist wires from new
factory speaker harness. wire back 1/2”. section on each factory speaker to stripped
speaker wire behind the sections of factory wires
factory speaker harness. as shown making sure
polarity is correct.
Factory Wires
---
-- - ------
Negative Wires
Strip Out 1/2” New Wires
+
+
+ + + + + + + + + + + + +
Positive Wires
3. Twist each positive pair of 4. Squeeze middle of cap 3. Heat wires first with 4. Wrap wiring connections
wires together and insert for tight connection. soldering iron, then with electrical tape.
in crimp cap. Repeat touch solder to
step for negative wires. 5. Connect new wires to wires for solid 5. Connect new wires to
speaker with spade connections. speaker with spade
First
connectors. connectors.
Factory Wire ---
-- - --------
Last
+
+
+ + + + + + + + + + + + + + + + + + + + +
1-800-955-9094
TECHNICAL SUPPORT Copyright 2018 Crutchfield Corporation 10