Professional Documents
Culture Documents
1.0 Safety
1.1. List First Aid equipment and describe industrial first aid procedures including:
1.1.1. shock mitigation
1.1.2. cut and abrasion treatment
1.1.3. blunt force treatment
1.2. Identify fire hazards and how to handle different classes of fires in the workplace
1.3. List basic rules associated with workplace safety including:
1.3.1. identifying surrounding conditions and possible safety issues
1.3.2. explaining the safe procedures while working in confined spaces
1.3.3. explaining industrial electrical safety rules described in electrical codes (e.g. NEC,
National Electrical Code; CEC, Canadian Electrical Code {CSA C22.1})
1.3.4. explaining safe lifting procedures
1.3.5. climbing and safety rules that OSHA (Occupational Safety and Health Administration of
the U.S. Dept. of Labor) and ANSI A14 dictates for workers at heights (American National
Standards Institute)
1.3.6. identifying potential environmental hazards in the workplace including:
1.3.6.1. atmosphere monitoring including low explosive limits (LEL),
1.3.6.2. flammability,
1.3.6.3. HAZMAT reactions (hazardous materials)
1.3.7. summarizing the use of material safety data sheets (MSDS)
1.4. Describe what types of Personal Protection Equipment (PPE) should be worn for work
environments where there is danger of:
1.4.1. Arc Flash and Arc Blast
1.4.2. eye injury
1.4.3. ear injury
1.4.4. head injury
1.4.5. lung injury
1.4.6. other injuries and the required work apparel
1.5. Describe safety procedures required working with and around industrial equipment including:
1.5.1. Lockout / Tag Out
1.5.2. tools and machines
1.5.3. products
1.5.4. test equipment
®
IND Competencies 1 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 2 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 3 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
4.7.11. Explain how ohms law correlates to these devices and the components contained
within them
4.8. Describe the use of iso-couplers
4.9. Describe the use of optical isolators
4.10. Recognize operational amplifier system level applications and characteristics of:
4.10.1. low noise
4.10.2. high input impedance
4.10.3. low output impedance
4.10.4. very high gain
4.10.5. sensors including difference detection
4.10.6. signal reduction/cancellation
4.10.7. Explain the circuit function application for amplifiers
4.11. Explain requirements for distribution system line amplifiers
4.12. Describe integrated circuit and semiconductor use in systems including:
4.12.1. differences/tolerances of supply voltages for CMOS versus TTL
4.12.2. designs using combinational logic:
4.12.2.1. decoders to activate an output action
4.12.3. Multiplexer/data selector
4.12.4. Demultiplexer/data distributor
®
IND Competencies 5 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 6 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 7 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
SPECIALTY AREAS:
Industrial Technologies Service Specialist should be knowledgeable in the following additional
technical Specialty areas in addition to the prior Core areas:
Specialty 1:
11.0 Industrial Communications
11.1. Define industrial communications information transmission methods
11.2. Identify the differences in modes of data transmission
11.3. Identify the structures of network digital communications
11.4. Describe how an Input Output (I/O) communication bus works
11.5. Explain Highway Addressable Remote Transducer automation protocol (HART ) communications
11.6. Identify the difference between physical and logical network topologies
11.7. Explain addressing in a digital network
®
IND Competencies 8 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
12.0 Networks
12.1. Describe network bus classifications and the devices with which they connect
12.2. Explain fieldbus protocols associated with a process bus network
12.3. Describe common basic network terminology
12.4. Explain how the TIA 606B standard is used to label cabling systems
12.5. Identify the basis of an industrial wireless communication system
12.6. Explain the difference between single channel radio and spread spectrum wireless
communication
12.7. Identify the transmission protocols used for wireless communications
12.8. Identify the wireless protocol standards
12.9. Identify the advantages/disadvantages wireless networks have over wired networks
12.10. Explain network cybersecurity systems
12.11. Identify wireless cybersecurity encryption methods
12.12. Describe how a Supervisory Control and Data Acquisition (SCADA) system manages a
network
Specialty 2:
13.0 Fluid Power
13.1. Describe Pascal’s law calculations (principle of transmission of fluid-pressure)
13.2. Identify compressor types and how they work
13.3. Identify the types of prime movers used with pumps
13.4. Describe hydraulic pump types and identify the terms:
13.4.1. accumulator
13.4.2. cavitation
13.5. Explain filter dryer methods
13.6. Identify pneumatic system components and their function
13.7. Identify pneumatic valve types
13.7.1. Describe valve actuation methods
13.8. Describe the function of linear cylinders/actuator types
13.9. Identify pneumatic plumbing methods
13.9.1. Describe an air distribution systems design
Specialty 3:
14.0 Instrumentation
14.1. Specify items typically regulated by process control
14.2. List types of final elements used in process control
®
IND Competencies 9 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
Specialty 4:
15.0 PLCs (Programmable Logic Controllers)
15.1. Explain the information derived from a PLC nomenclature tag
15.2. Identify PLC output types
15.3. Describe the process and methods used to input / program a PLC including:
15.3.1. PLC schematic symbols
15.3.2. PLC ladder diagrams functions including:
15.3.2.1. logic
15.3.2.2. math
15.3.2.3. compare
15.3.3. PLC expansion addressing
15.4. Describe methods used for networking PLCs
15.5. Describe the following types of discrete controller modules:
15.5.1. DC and AC
15.5.2. analog
15.5.3. microcontrollers
15.5.4. specialty (such as communications; coprocessors; encoders; motion)
15.5.5. signal conditioning
15.6. Describe open source protocols and devices that use them to include:
15.6.1. Arduinos
15.6.2. PIC microcontrollers and DSCs
15.6.3. Raspberry Pi
®
IND Competencies 10 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
15.6.4. LocNet
15.6.5. DeviceNet
15.6.6. BacNet, etc.
15.7. Explain the advances of hardware and software interfacing including optical couplers
15.8. Describe the application to automation operation of and a production process for:
15.8.1. ladder logic instructions
15.8.2. timer instructions
15.8.3. counter instructions
15.8.4. sequencer instructions
15.8.5. discrete control functions
15.8.6. math comparisons
15.9. Explain how the following functions affect the process control cycle:
15.9.1. loop
15.9.2. data comparison
15.9.3. branch
15.9.4. add/subtract
15.9.5. multiply/divide
15.10. Describe physical requirements/best practices in installation of:
15.10.1. PLC panel layout
15.10.2. enclosure environmental control
15.10.3. maintenance
15.10.4. surge protection
Specialty 5:
16.0 Robotics
16.1. Explain robot design that is created to perform one or more of the “three D’s” (dull, dirty, or
dangerous)
16.2. Describe the characteristic robot types to include:
16.2.1. autonomous
16.2.1.1. programmable
16.2.2. guided
16.2.3. remote control
16.2.3.1. ROVs types
16.3. Explain the term “End of Arm Tooling”
16.4. List the six axis of movement in a typical robotic arm
16.5. Define a robotic work-cell to include:
16.5.1. subsystems
16.6. Identify robot power sources
16.7. List robot feedback devices
16.8. Describe the sources of robot hazards as listed in OSHA Instruction PUB 8-1.3 SEP 21, 1987
Office of Science and Technology Assessment
16.9. Describe the purpose of ISO 9283 as it relates to robotics
16.10. Explain how the ANSI/RIA R-15.06-2012 standard will affect the robotics industry
®
IND Competencies 11 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 12 © Copyright 2020, ETA International, All Rights Reserved
®
ETA International – Certified Industrial Electronics
®
IND Competencies 13 © Copyright 2020, ETA International, All Rights Reserved