Professional Documents
Culture Documents
Purpose The purpose of the "Laser Beam Position Check and Adjustment" is:
Checking the laser beam position, to see, whether it is centered to the calibration
board.
Adjustment of the optic module this way that the laser beam position is centered
to the calibration board.
Use Case Perform the "Laser Beam Position Check and Adjustment" in following cases:
In case of sporadic or persistent errors 10761 or 10767 to identify the possible
root cause of an incorrect laser beam position
To solve errors 10761 or 10767, if an incorrect laser beam position is the root
cause
REQUIRED TOOLS:
3 mm
REQUIRED TIME:
Approximately 30 minutes
IMPORTANT:
This adjustment requires:
Calibration board version 2* and
Distributor board version 2* (see Figure 25) and
Software ≥ CRE_1511**
For digitizers with lower serial numbers, which do not fulfil the requirements, it can also
be performed with the Laser Beam Detection Toolkit, spare part number***:
CM+9 5175 2940 0
The Laser Beam Detection Toolkit has instructions for installation and adjustment
included.
* Installed in SN ≥ 6397 (Type 5175/100) and SN ≥ 5935 (Type 5175/110) and in all digitizers, where the
calibration board was exchanged after September 2009.
** Installed in SN ≥ 5570 (Type 5175/100) and SN ≥ 6377 (Type 5175/110).
*** The last digit in the spare part number indicates the spare part revision at release of
this document. When ordering, the actual revision of the spare part is delivered.
Distributor Board
Version 1
Distributor Board
Version 2
5175_enc900.cdr
The laser beam position check and adjustment is divided in following steps:
# Step Section
1 Performing the Laser Beam Position Check 2.5.1
2 Performing the Laser Beam Position Adjustment 2.5.2
3 Verifying the Laser Beam Position Check and 2.5.3
Adjustment
NOTE:
Short description of the laser beam position check:
The laser beam is switched on via service client.
By putting the switch on the distributor board to ON position the laser beam
position check functionality is activated: The yellow "LED 1" lights up.
If "LED 2" and "LED 3" on the distribution board are light up, the laser beam
position is OK.
Optic Module
Position Plate 2
Optic Module
Optic Module
Position Plate 1
EOL Sensor
Figure 26: Functional principle of the laser beam position check and adjustment
Figure 27
517536df.cdr
OFF ON
Figure 28
DANGER:
If the power cord is connected and the main switch is switched on the input
side of the power supply is connected to high voltage. Risk of live.
Do not touch the input side of the power supply by hand or with any tool.
LED 1
Figure 29
Figure 30
WARNING:
Laser light. Eye injuries possible.
Do not keep any tool in the laser beam while the laser is switched on.
(15) Select the button <On> to switch on the laser beam. See Figure 31.
The status message shows <Polygon is spinning. Laser ready>.
See Figure 32. The Polygon motor is audible.
Figure 31 Figure 32
NOTE:
The laser beam switches off automatically after 30 minutes.
LED 1
Switch
Figure 33
# Status Action
1 LED 1 ON LED 2 ON LED 3 ON No further action required. Laser beam
position OK. Continue with next step.
2 LED 1 ON LED 2 OFF LED 3 ON Laser beam position adjustment
required. Continue with section 2.5.2.
3 LED 1 ON LED 2 ON LED 3 OFF
4 LED 1 ON LED 2 OFF LED 3 OFF Check, whether laser beam is really
switched on: Look from the digitizer
right hand side, whether the red laser
line is visible. For more information
refer to the troubleshooting guide,
DD+DIS151.08E.
If laser beam is visible, the laser beam
position adjustment is required.
Continue with section 2.5.2.
5 LED 1 LED 2 OFF LED 3 OFF Set switch to ON position.
OFF
CAUTION:
If switch on distributor board stays in "ON" position during digitizer operation,
reduced image quality possible.
Set the switch on the distributor board to the OFF position before handing the digitizer
over to the customer.
Figure 34
NOTE:
Before starting the laser beam position adjustment, first perform the laser beam
position check. See steps (1) to (17) in section 2.5.1.
Figure 35
Figure 36
LED 1
Switch
Figure 37
Figure 38
Figure 39
CAUTION:
If switch on distributor board stays in "ON" position during digitizer operation,
reduced image quality possible.
Set the switch on the distributor board to the OFF position before handing the digitizer
over to the customer.
ME D IC A L EL E CT R IC A L
EQU IP ME NT
WI TH RE SP E CT T O
E L EC TR I C S HOC K , F RI E,
A ND MEC H A NI C AL
U
L
H AZ A RD S ON LY I N Made in Germany
AC C ORD A N C E WI TH
U L6 060 1-1 / C R US P eissenberg
C A N /C S A C 22. 2 N O.6 01. 1 MMMMM-Y YY Y
9F 03
Direction
Figure 40
CALIBRATION:
(1) Perform a shading calibration. Refer to section 3.1 of this chapter.
Verification If only the laser beam position check has been performed:
(1) Insert cassette with unexposed IP in the digitizer.
(2) At the workstation select examination type “System diagnosis – Flatfield”.
(3) Select “ID” to identify the image: Scanning starts.
(4) Confirm that the image arrives at the workstation.
(5) Reject the image.