Professional Documents
Culture Documents
New
■ Fire resistance F90 from below and from above with up to 3.5 m span width
■ Maximum spacing of ceiling profiles increased to 625 mm
Knauf Free-spanning Fireboard Ceiling A1 K219
Fire protection from below / from below and from above (Plenum)
Subceilings with sole fire rating
From below Fire resistance Knauf System
For fire exposure from below, the fire class
rating of the "subceiling solely" covers for fire exposure Cladding Sub- Insulation layer
the constructions above, such as structure (required for
ceiling or roof constructions.
Type/ Min.- Max. axial fire protection)
(e. g. trapezoid sheet metal roofs)
from from building thickness spacing
From above below above
Fire exposure from the ceiling plenum. material ceiling profiles
The ceiling or roof construction above class
b Min. Min.
has to be of the same fire rating.
Proof
thickness density
mm mm mm kg/m³
Fireboard 20
A1 + Mineral wool S
F90 F90 625 1
Z-PA-III 20 60 50
4.290 upper cover
Load bearing capacity (min.): 1) shear: 0.35 kN; 2) shear: 0.35 kN; extraction: 0.5 kN
Flex
Profile
30 mm
Fasten Fireboard covering strips using Drywall Screws
TN 3.5x25 mm at a spacing of 250 mm alternating
100 mm on double profiles
Knauf UW runner Knauf CW double profile with Fastening of Knauf Boards with Drywall Screws TN
Flex Profile Fireboard covering strips
Cladding on metal profiles Maximum
Connect Knauf CW double profile with UW runner on each flange (penetration 10 mm) spacing of
Thickness in mm metal gauge 0.7 mm fasteners
b C
D D B B
Room width in m
Knauf CW double profile Max. spacing of Fireboard Max. room width Knauf UW runner
as ceiling profile ceiling profiles perimeter support
Drywall Screw Knauf Fireboard 2x 20 mm Drywall Screw TN 3.5x35 Fibre Glass Joint Tape
TN 3.5x55 Fireboard Filler
b 625 mm 625 mm b
K219vu-B3 Front edge joint (B-B) K219vu-C3 Long edge joint (C-C)
Connect free-spanning Knauf CW double profile on each top flange with Knauf UW runner
Note by riveting, crimping or screwing with Metal Screws LB 3.5x9.5 (see page 3).
4
Knauf Free-spanning Fireboard Ceiling A1 K219
Fire resistance F90 ● solely from below
Details, scale 1:5
Knauf CW profile
Knauf UW runner as perimeter support Fireboard strips
(anchoring acc. to page 3) Drywall Screw TN
K219vu-A3 Constructional
partition (A-A)
connection to K219vu-A4 Constructional connection to wall
with shadow gap (A-A)
5
Knauf Free-spanning Fireboard Ceiling A1 K219
Fire resistance F90 ● solely from below and from above
A
C
D D B B
140 mm
K219vuvo-B3 Front edge joint (B-B) K219vuvo-C3 Long edge joint (C-C)
Note Connect free-spanning Knauf CW double profile on each flange with Knauf UW runner (see pagee 3).
6
Knauf Free-spanning Fireboard Ceiling A1 K219
Fire resistance F90 ● solely from below and from above
Details, scale 1:5
K219vuvo-A3 Constructional
partition (A-A)
connection to K219vuvo-A4 Constructional connection to
wall with shadow gap (A-A)
25 a 25 a
ca. 100 mm ca. 100 mm a 20 mm
625 mm 625 mm
400 mm 420 mm
Clearance
SO1 SO1
SO3 SO3
Clearance
600 mm
SO2 SO4
SO2 SO4
2x 20 mm Fireboard encasement Fold Knauf UW Profile and connect
Fold Knauf UW Profile and connect with double profile
with additional CW Profile Knauf CW double profile
Additional continuous Knauf CW Profile
Knauf CW double profile
Scheme drawing, top view Scheme drawing, top view
625 mm
400 mm Note Alutop Access Panel on request
40 625 mm 625 mm
Built-in lighting
10 kg max.
Built-in lighting
10 kg max.,
fastening acc. to
providers spec.
Additional continuous Access panel
Knauf CW Profile 600 mm
Clearance
SO3 SO3
SO1 SO1
Clearance
600 mm
SO2 SO4
SO2 SO4
Additional continuous Knauf CW Profile Circumferential 12.5 mm Fireboard strip
with 20 mm Fireboard strip on the Fold Knauf UW Profile and slide on
rear side double profile
Knauf CW double profile with covering strip Knauf CW double profile with covering strip
Scheme drawing, top view Scheme drawing, top view
Built-in lighting
10 kg max.,
fastening acc. to
providers spec.
Built-in lighting
10 kg max.
or
CW Profile 50x50x0.6; (up to 5.0 m long) -
CW Profile 75x50x0.6; (up tp 6.0 m long)
or
or
CW Profile 100x50x0.6; (up tp 6.0 m long) m 0.2 0.2
CW Profile 125x50x0.6; (custom.)
or
CW Profile 150x50x0.6; (custom.) -
Anchoring of CW Profiles as perimeter connection:
or Knauf Multi-purpose Screw FN 4.3 x 35 mm pcs
or Knauf Ceiling Steel Dowel; (package 100 pcs) as required as required
or Knauf Nailable Plug "L" 8/80; (package 50 pcs)
suitable, approved anchor
Substructure
Knauf CW double profiles as ceiling profile:
or
CW Profile 50x50x0.6; (up to 5.0 m long) -
CW Profile 75x50x0.6; (up tp 6.0 m long)
or
or
CW Profile 100x50x0.6; (up tp 6.0 m long) m 3.0 3.0
CW Profile 125x50x0.6; (custom.)
or
CW Profile 150x50x0.6; (custom.) -
Knauf CW double profiles, screw connected at web
Knauf Metal Screw LB 3.5 x 9.5 mm pcs 2.4 2.4
Connection of double profiles with supporting UW runners:
or e.g. blind metal rivets 2.6 -
pcs -
e.g. TN 3.5 x 25 mm 2.6
Insulation (observe fire protection requirements; see page 2) m² as required 1.0
Cladding
Knauf Fireboard; 20 mm m² 2.0 1.0
Knauf Drywall Screws; (fastening of Fireboard)
TN 3.5 x 35 mm 10 -
TN 3.5 x 45 mm pcs - 18
TN 3.5 x 55 mm 18 -
Fireboard covering strip, 120 mm wide:
Knauf Fireboard; 12.5 mm m² - 0.4
Knauf Drywall Screws; (fastening of covering strips)
TN 3.5 x 25 mm pcs - 15
additional layer (covering):
Knauf Fireboard; 20 mm m² - 1.0
additional layer (upgrading of partition):
Knauf Fireboard; 20 mm m² as required as required
Flex Profile - 0.8
Filling
Knauf Fireboard Filler; (5 kg/20kg bag) kg 0.12 0.06
Knauf Fibre Glass Joint Tape; (25 m roll) m 1.1 1.1
Trenn-Fix 65; (50 m roll) m 1.0 1.0
Edge Trim 23/13; (2.75 m long) m as required as required
10
Knauf Free-spanning Fireboard Ceiling A1 K219
Tender Specifications
Item Description No. of units Unit price Total price
Access panel,
........ fire resistance F90,
with aluminium frame, dimensions in mm .........................,
filling made of Knauf boards, thickness in mm ................. ,
for free-spanning ceiling.
Product: Knauf Access Panel D171 ........... pcs .......... € .......... €
11
K219 Knauf Free-spanning Fireboard Ceiling A1
Construction, Application, Filling / Coats and linings
Construction
Knauf Free-Spanning Fireboard Ceilings A1 are Joints (extensions) of free-spanning profiles are built-ins like lighting fixtures, with control joints that
solely anchored on the walls at perimeter. Knauf NOT allowed. Movement joints of the main struc- allow for movement, e. g. shadow gaps.
Fireboard (gypsum fleece boards of building ma- ture have to be taken over into the construction of Knauf profiles are delivered galvanized. The cor-
terial class A1) are fastened to a metal substruc- the Knauf Fireboard Ceilings. Use control joints in rosion protective coating is sufficient for indoor
ture made of Knauf CW double profiles. The appli- the case of ceiling areas over approx. 15 m length, application, including bathrooms and kitchens in
cation of additional loads like lighting fixtures with or for narrow ceiling spaces caused by a break of private housing. For other areas, e. g. under in-
max. 100 N (10 kg) per double profile (50 N per m² a wall. Separate connections of Knauf Fireboard to fluence of outdoor air, additional corrosion pro-
ceiling area) with suitable anchors directly to the components made of materials other than gypsum, tection is necessary (see DIN 18168-1 table 2).
metal substructure is permissible. especially columns, or thermally highly stressed
Application
If the free-spanning ceiling is connected (an- with Metal Screws LB 3.5 x 9,5 mm at a spacing at the board edges in order to avoid buckling.
chored) to a lightweight partition (F90), an addi- of 750 mm max. Firmly push Fireboard to substructure and fas-
tional, 20 mm thick Fireboard cladding layer is re- ■ Support length of CW double profiles in UW pe- ten with Drywall Screws TN at a spacing of 170
quired for the partition on the side of the support- rimeter runners has to be at least 30 mm. Con- mm alternating on the CW double profiles.
ing connection. nect both top flanges of CW double with the UW ■ In case of double layer cladding, the spacing of
Substructure runner by riveting /crimping or screwing with LB the screws can be increased for the first layer to
■ Supporting perimeter connection made of UW 3.5 x 9.5, if no covering strip is required. 500 mm if the second layer is applied immedi-
Profiles. Anchoring acc. to table on page 3. In ■ Only in case of fire protection solely from below ately afterwards (on the same day).
case of connection to a lightweight partition AND from above: Fasten Knauf Fireboard strips, ■ Only in case of fire protection solely from below
(F90) and fire protection from below AND from 12.5 mm thick, 120 mm wide, as covering strips AND from above: Apply covering layer of Knauf
above, apply Flex Profile underneath the addi- on top and bottom of the CW double profiles al- Fireboard 20 mm without fastening, tightly joint-
tional Fireboard layer on the partition for the an- ternating with Drywall Screws TN 3.5 x 25 mm ed.
choring of the supporting perimeter runner. at a spacing of 250 mm max. Connection of CW ■ Fastening of 20 mm thick Fireboard with Drywall
Spacing of anchors in this case: 312.5 mm double profiles with UW perimeter profiles acc. Screws TN 3.5 x 45 mm /
■ In case of sound protection requirements, seal to page 3. 2 x 20 mm with TN 3.5 x 45 mm + TN 3.5 x 55
up carefully with Acoustical Sealant according Cladding mm.
to DIN 4109, supplement 1, chapter 5.2; porous ■ Apply Knauf Fireboard parallely to CW double ■ Apply Knauf Trenn-Fix 65 on connections to ad-
sealant strips like Sealing Tape are usually not profiles. Place long edge joints on profiles. jacent components and fill connection joints with
suitable in this case. ■ Stagger front edge joints by 400 mm min. Fireboard Filler.
■ Connect CW Profiles as double profiles at web ■ Start fastening Fireboards in the board centre or
Knauf Direct Knauf Drywall and Floor Systems Am Bahnhof 7, 97346 Iphofen, Germany
Technical Advisory Service:
* A rate of 0.39 € per minute will be charged for calls from within the German landline network. Callers whose phone numbers are not registered in the address database
of Knauf Gips KG, i.e. private builders or non-patrons, will be charged a rate of 1.69 € per minute. Calls from mobile phones will be charged 1.48 € per minute.
Phone: +49 9001 31-1000 *
** 0.14 €/Min.
Fax: +49 1805 31-4000 **
All technical changes reserved. Only the current printed instructions are valid. Our warranty is expressly limited to our products in flawless condition. All application quantities and delivery amounts
are based on empirical data that are not easily transferable to other deviating areas. The stated information represents current state-of-the-art Knauf technology. The entire state of approved en-
gineering rules, appropriate standards, guidelines, and rules of craftsmanship are not included herewith. These and all application instructions have to be adhered to separately by the installer.
All rights reserved. All amendments, reprints and photocopies, including those of excerpts, require the express permission of Knauf Gips KG, Am Bahnhof 7, 97346 Iphofen, Germany. Delivery
www.knauf.de via professional building material distributors only, in accordance with our current business, delivery and payment terms.
The constructional and structural properties, and characteristic building physics of Knauf systems can solely be
K219/engl./D/02.05/FB/D
ensured with the exclusive use of Knauf system components, or other products expressly recommended by Knauf.