Professional Documents
Culture Documents
SERIES
Cylinder stroke
Number of positions 2 positions
Number of ports 2, 3 ports 5 ports
Valve function Normally closed (NC) Single solenoid
Remark: For optional specifications and order codes, see p.91∼92.
t1 t2 t3 Time
Solenoid valve
Cylinder stop
Cushioning
Cylinders start
energized
impact
Specifications
Basic model Direct piping, To obtain the time required for the cylinder to
030E1 030-4E1
Item T, F, F01 type manifolds complete 1 stroke, add the cylinder’s delay time
t1 (time between energizing of the solenoid valve
Media Air
and actual starting of the cylinder), to the
Operation type Direct acting type Internal pilot type cylinder’s max. speed operating time t2.
1
(P)→2
(A)
0.6〔0.03〕 (
1 P)→4 (A) ,(2 B)0.6
〔0.03〕 When a cushion is used, add the cushioning time
Effective area〔Cv〕 mm2 t 3 , to the above calculations. The standard
2
(A)
→3(R)0.8〔0.04〕 (
4 A)→5(R1),(
2 B)→3(R2)0.8〔0.04〕
cushioning time t3 is approximately 0.2 seconds.
Port size Note M5×0.8
Lubrication Not required Measurement conditions
Operating pressure range MPa {kgf/cm2} [psi.] 0∼0.7 {0∼7.1} [0∼102] 0.15∼0.7 {1.5∼7.1} [22∼102] ●Air pressure: 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length:
Proof pressure MPa {kgf/cm2} [psi.] 1.05 {10.7} [152] φ2.5 [0.1in.]×1000mm [39in.]
Response time DC12V, DC24V 10/25 or below ●Fitting: Quick fitting
ms Valve side: TS4-M5
ON/OFF AC100V, AC200V 15/40 or below Cylinder side: TS4-M5 (φ10, φ16)
Maximum operating frequency Hz 5 TS4-01 (φ20)
Load
Operating temperature range (atmosphere and media) °C [°F] 5∼50 [41∼122] ●Load ratio= (%)
Cylinder theoretical thrust
Shock resistance m/s2{G} 117.7 {12.0} ●Cylinder stroke: 60mm [2.36in.] (φ10,φ16)
100mm [3.94in.] (φ20)
Mounting direction Any Load
Cylinder
Solenoid valve 030-4E1
0.5MPa
Fitting TS4-M5
Solenoid Specifications Fitting TS4-M5
or TS4-01
030E1 2(A)
0.5 0.7
3(R) ─ φ1.8
0.4 0.6
0.5 1(P)
0.3 Female thread M5×0.8
0.4 030-4E1 4(A), 2(B)
0.3
0.2 3(R2), 5(R1) ─ φ1.8
0.2
0.1 0.1
0 10 20 30 40 50
Flow rate R/min (ANR)
1MPa = 145psi., 1R/min = 0.0353ft.3/min.
Manifold Port Size
How to read the graph Manifold model Port Location of piping ports Port size
When the supply pressure is 0.5MPa
1(P) Manifold
[73psi.] and flow rate is 29R/min M5×0.8
[1.02ft.3 /min.] (ANR), the valve outlet YM□T 2(A) Valve
pressure becomes 0.4 MPa [58psi.]. 3(R) Manifold M6×1
1(P) Manifold
M5×0.8
YM□F 4(A), 2(B) Valve
3, 5(R) Manifold M6×1
1(P) Manifold Rc1/8
YM□F01 4(A), 2(B) Valve M5×0.8
3, 5(R) Manifold Rc1/8
90
EA SERIES SPECIFICATIONS
Specifications
Specifications
EA10□F1
Basic model For direct piping,
EA10□F2
F type manifold EA10□F5 EA10□F6
EA10□F3
EA10□F4
For base piping, EA10□A1
EA10□A2
A, AJ type EA10□A5 EA10□A6
Item EA10□A3
manifolds EA10□A4
Media Air
Operation type Internal pilot type
Flow rate charac- Sonic conductance C dm 3/(s・bar) Base piping (A, AJ type): 0.26
teristicsNote 1 Effective area S〔Cv〕 mm2 Direct piping (F type): 1.3〔0.07〕
Port sizeNote 2 M3×0.5
Lubrication Not required
Operating pressure range MPa {kgf/cm2 } [psi.] 0.2∼0.7 {2∼7.1} [29∼102]
Proof pressure MPa{kgf/cm2 } [psi.] 1.05 {10.7} [152]
Standard type 10/20 or below 12 or below
Response timeNote 3
ms Low current type (L) 10/50 or below 12 or below
ON/OFF
Quick response type (S) 6/7 or below 6 or below
Maximum Standard type 5
operating Low current type (L) 2
Hz
frequency Quick response type (S) 10
Minimum time to energize for self holdingNote 4 ms ― 50
Operating temperature range (atmosphere and media) °C [°F] 5∼50 [41∼122]
Shock resistance m/s2 {G} 1373.0 {140} (Axial direction 294.2 {30}) 1373.0 {140} (Axial direction 147.1 {15})
Mounting direction Any
Notes: 1. For details, see the flow rate characteristics on p.110.
2. For details, see the port size on p.110.
3. Values when air pressure is 0.5MPa [73psi.].
4. For double solenoid valves.
Solenoid Specifications
― ― 23 125
Low current type
109
Port Size
The test method for flow rate characteristics conforms to JIS B 8390:2000 (test method for pneumatic equipment — equipment for compressible fluids — flow rate
characteristics).
0.6 0.6
Valve outlet pressure
0.5 0.5
0.4 0.4
0.3 0.3
0.2 0.2
0.1 0.1
0 0
20 40 60 80 100 120 140 20 40 60 80 100
Flow rate R/min(ANR) Flow rate R/min(ANR)
● Graphs use flow rate calculations based on the discharge method. 1MPa = 145psi., 1R/min = 0.0353ft.3/min.
● Use the flow rate as a guide.
110
SOLENOID VALVES
SERIES
Specifications
Basic model Standard type Low current type
Item 050E1 050-4E1 050-4E2 050LE1 050-4LE1
Media Air Air
Operation type Direct acting type Direct acting type
Effective area〔Cv〕 mm2 1.5〔0.08〕 1.2〔0.07〕 1.5〔0.08〕 1.2〔0.07〕
Port size Note 1 M5×0.8 M5×0.8
Lubrication Not required Not required
Operating pressure range MPa {kgf/cm2} [psi.] 0∼0.7 {0∼7.1} [0∼102] 0.15∼0.7 {1.5∼7.1} [22∼102] 0∼0.7 {0∼7.1} [0∼102]
Proof pressure MPa {kgf/cm2} [psi.] 1.05 {10.7} [152] 1.05 {10.7} [152]
Response time Note2 DC24V 20/20 or below 20 or below 30/30 or below
ms
ON/OFF AC100V, AC200V 25/25 or below 20 or below ──
Maximum operating frequency Hz 5 5
Minimum time to energize for self holding ms ── 50 ──
Operating temperature range (atmosphere and media)°C [°F] 0∼50 [32∼122] 0∼50 [32∼122]
Lateral direction 1373.0 {140.0} 1373.0 {140.0}
Shock resistance m/s2{G}
Axial direction 294.2 {30.0} 147.1 {15.0} 294.2 {30.0}
Mounting direction Any Any
Notes: 1. For details, see the port size on p.136.
2. Values when air pressure is 0.5MPa {5.1 kgf/cm2} [73 psi.]. Values of the double solenoid valve are switching time from the opposite position.
Solenoid Specifications
Rated voltage Standard type Low current type
Item DC24V AC100V AC200V DC24V
Type DC type Flywheel type DC type
21.6∼26.4 90∼110 180∼220 21.6∼26.4
Operating voltage range V
(24 +− 10%) (100 +
− 10%) (200 +
− 10%) (24 +− 10%)
Frequency Hz ─ 50 60 50 60 ──
CurrentNote 1
(when rated voltage is applied) 240(5.8W) 74 71 48 46 100(2.4W)
EnergizingNote 2 mA(r.m.s)
〔252(6.0W)
〕 〔83〕 〔79〕 〔50〕 〔48〕 〔112(2.7W)
〕
Maximum allowable leakage current mA 20 10 5 10
Insulation resistance MΩ 10 10
Wiring type and Standard Grommet type: 300mm [11.8in.] Grommet type: 300mm [11.8in.]
lead wire length Optional With DIN connector With DIN connector
Red Red
Color of lead wire 〔Red(+), Blue(−)〕Note 1 Yellow, Black White, Black 〔Red
(+) (−)
, Blue 〕Note 1
Red(+), Black(−)Note 3 (+)
Red (−)Note 3
, Black
135
Solenoid Valve Port Size Solenoid Valve Mass g [oz.]
Basic model Port specification Port size Basic model Mass
Female 050E1 190 [6.70] (185 [6.53])
Standard M5×0.8
050E1Note, 050-4E1 thread 050-4E1 190 [6.70] (185 [6.53])
Cylinder Operating Speed To obtain the time required for the Flow Rate
cylinder to complete 1 stroke, add
the cylinder’s delay time t 1 (time
Cylinder stroke
Cushioning
Cylinder stop
Cylinder
0.6
Solenoid
0.5
0.3 0.4
1000
speed
Supply pressure
Valve outlet pressure
0 10 20 30 40 50 60 70
Load ratio %
136
JC SERIES SPECIFICATIONS
Specifications
Specifications
JC10□F1 JC10□F7
Basic model For direct piping,
JC10□F2
F type manifolds JC10□F5 JC10□F6 JC10□F8
JC10□F3
JC10□F4 JC10□F9
JC10□A1 JC10□A7
For base piping, JC10□A2
A type manifolds JC10□A5 JC10□A6 JC10□A8
Item JC10□A3
JC10□A4 JC10□A9
Media Air
Operation type Internal pilot type
Flow rate characteristicsNote 1
0.6
Sonic conductance C dm 3/(s・bar)
Port sizeNote 2 M5×0.8
Lubrication Not required
Operating pressure range MPa {kgf/cm2 }[psi.] 0.2∼0.7 {2∼7.1} [29∼102] 0.25∼0.7 {2.5∼7.1} [36∼102]
Proof pressure MPa {kgf/cm2 }[psi.] 1.05 {10.7} [152]
Standard type 10/20 or below 12 or below 10/30 or below
Response timeNote 3
ms Low current type (L) 10/50 or below 12 or below 10/60 or below
ON/OFF
Quick response type (S) 6/7 or below 6 or below 6/12 or below
Standard type 5
Maximum operating
frequency Hz Low current type (L) 2
Quick response type (S) 10
Minimum time to energize for self holdingNote 4 ms ― 50 ―
Operating temperature range (atmosphere and media) °C [°F] 5∼50 [41∼122]
Shock resistance m/s2 {G} 1373.0 {140} (Axial direction 294.2 {30}) 1373.0 {140} (Axial direction 147.1 {15}) 1373.0 {140} (Axial direction 195.0 {20})
Mounting direction Any
Notes: 1. For details, see the flow rate characteristics on p.236.
2. For details, see the port size on p.237.
3. Values when air pressure is 0.5MPa [73psi.]. The values for the 3-position valves are switching time from the neutral position.
4. For double solenoid valve.
Solenoid Specifications
235
Flow Rate Characteristics
The test method for flow rate characteristics conforms to JIS B 8390:2000 (test method for pneumatic equipment — equipment for compressible fluids — flow rate
characteristics).
Notes: 1. Quick fitting TSH6-M5Ms are mounted on connection ports 1(P), 2(B), and 4(A).
2. Quick fitting TSH6-M5Ms are mounted on connection ports 2(B) and 4(A).
3. Figures in effective area S are calculated based on sonic conductance C (S=5.0×C).
MPa 0.7
0.6
Valve outlet pressure
0.5
0.4
0.3
0.2
0.1
0
100 200 300 400
Flow rate R/min (ANR)
1MPa = 145psi., 1R/min = 0.0353ft3/min
● The graph uses flow rate calculations based on the discharge method.
● Use the flow rate as a guide.
236
Reliability & Versatile Applications
a confined space.
293
Twin Solenoid Valve
Ensures the functions of the
conventional double solenoid type,
but in a much shorter length, while
simple wiring enables correct
connections with a sequencer.
Moreover, it is capable of being
installed on a conventional manifold
to occupy space for two stations.
294
SOLENOID VALVES 062 SERIES
Direct acting 2-, 3-, 4-port
Symbols
Single solenoid (E1) type Double solenoid (E2) type Keep solenoid (SE2) type
2-port 3-port 4-port 2-port 3-port 4-port 2-port 3-port 4-port
NC NO NC NO NC/NO NC/NO NC/NO ――― NC/NO NC/NO ―――
S S S
R R R
R R R A P A R R A R R A
P A
P A P A P A P A P P A P B P A P B
B
062E1-2 062E1-2-11 062E1 062E1-11 062-4E1 062E2-2 062E2 062-4E2 062SE2-2 062SE2 062-4SE2
Item Model 062E1-2 062E1-2-11 062E1 062E1-11 062-4E1 062E2-2 062E2 062-4E2 062SE2-2 062SE2 062-4SE2
Number of positions 2
Number of ports 2 3 4 2 3 4 2 3 4
Single solenoid Double solenoid Keep solenoid
Valve function Normally closed Normally open Normally closed Normally open Normally closed (NC) Normally closed (NC)
――― ――― ―――
(NC, standard) (NO, optional) (NC, standard) (NO, optional) or Normally open (NO) or Normally open (NO)
Specifications
Item Model 062E1-2 062E1-2-11 062E1 062E1-11 062-4E1 062E2-2 062E2 062-4E2 062SE2-2 062SE2 062-4SE2
Media Air
Operation type Direct acting
Effective area〔Cv〕 mm2 〔0.12〕
2.5 1.8〔0.08〕 〔0.12〕
2.5 〔0.08〕
1.8 〔0.12〕
2.5 〔0.08〕
1.8
Port size Rc 1/4
Lubrication Not required
Operating pressure range MPa{kgf/cm2} [psi.] 0∼0.9 {0∼9.2} [0∼131]
Proof pressure MPa{kgf/cm2} [psi.] 1.35 {13.8} [196]
Response time ON 30
ms
ON/OFF OFF 30
Maximum operating frequency Hz 5
Minimum time to energize for self holding ms | 50
Operating temperature range (atmosphere and media) °C [°F] 0∼60 [32∼140]
Mounting direction Any
Mass kg [lb.] 0.3 [0.66] 0.5 [1.1] 0.4 [0.88]
Solenoid Specifications
Item Solenoid type Single solenoid (E1) Double solenoid (E2) Keep solenoid (SE2)
Voltage type V See the Voltage Types and Current.
Voltage range % Rated voltage ±10% Rated voltage +10%, −5%
Current mA See the Voltage Types and Current.
Energizing type Continuously energizing type Common type for momentarily and continuously energizing
Insulation type B type
Wiring type Grommet type
Lead wire length mm [in.] Approximately 300 [11.8]
887
Inner Construction, Major Parts and Materials Flow Rate
Silicon diode
De-energized Energized MPa
0.9 Supply pressure
MPa
Armature spring 0.8
Solenoid 0.7
0.9
Poppet stem
●4-port
setting screw
MPa
0.9
B R1 B R1 Supply pressure
0.8 MPa
Poppet A A 0.7
0.9
P P 0.7
0.5
0.6
●Although the Inner construction schematic diagram shows R1 and R2 separately, these are in fact 0.4 0.5
0.4
combined inside the body, with just the Rc1/4 female thread leading to the outside. 0.3
●For the keep solenoid (SE2) type and double solenoid (E2) type, see p.881. 0.3
0.2 0.2
0.1 0.1
0
Parts Materials 50 100 150 200 250
Body Aluminum alloy (anodized) Flow rate R/min (ANR)
Poppet stem Brass How to read the graph
Poppet When the supply pressure is 0.5MPa [73psi.] and
Synthetic rubber the flow rate is 85R/min [3.0ft.3/min.] (ANR), the
888
1503-1504_F55-012_cENG cENG 2nd
Solenoid Valves
5-Port
Q5-Port Direct Connection / Base Plumbing Solenoid Valves • M5 Type Q5-Port Base Plumbing Solenoid Valve • Arrangement and Selecting Order of Solenoid Valve Installation
Direct Connection / Single Solenoid Direct Connection / Double Solenoid • M5 Type • Rc1/8 Type
82 112
16.5 19 46.5 19 46.5 Number of Positions
1 2 3 •••••• Number of Positions
A B A B
B B 6 15 17 17 15 6 1 2 3 ••••••
11
11
15
10
15
A
10
A
6
2-Ø2.8 2-M5x0.8 2-Ø2.8
32.8
2-M5x0.8 11 11 SOL.a
(4.3)
SOL. a
(4.3)
4-Ø4.5
(31.8)
(31.8)
QJIS Symbol
27.5
27.5
20
16
68
60
• M5 Type • Rc1/8 Type
33.5
4-Ø4.5
4
MSSY MSMY
4
(Base for M5 Type + Solenoid Valve) (Base for Rc1/8 Type + Solenoid Valve)
29
Single Solenoid Single Solenoid 2-Ø3.2 2-Ø3.2
A B B A B A 20.5 11 50.5 11
MSSYB (Base for M5 Type) MSMYB (Base for Rc1/8 Type)
24.8
21.6 21.6 SOL.b SOL. b
3-M5x0.8 3-M5x0.8 21 17.5
L
R1 P R2 R 2 P R1 R2 P R1 5 L 5
K
Double Solenoid Double Solenoid R1 P R2 R1 P R2
A B B A B A 26 56 56 56
• M5 Type • Rc1/8 Type
Single Solenoid
Base Plumbing / Single Solenoid Base Plumbing / Double Solenoid 82 15
• Rc1/8 Type 82 112 16.6 2 x <Number of
R1 P R2 R2 P R1 R2 P R1 26 56 Positions> -Rc1/4
(4.3)
61.8 33.8
(4.3)
5-Rc1/8
16.5 19 5-Rc1/8
46.5 19 46.5
QFeatures 2-Ø3.1 14.5 25.5 2-Ø3.1 14.5 55.5
1011.6
1011.6
1516.6
1516.6
2x Number of Positions -Rc1/8
2.4
2.4
• Direct Connection Type can be directly connected to the pipes. • Direct Connection Type A B A B
56.5
R1
70.25
• Base Plumbing Type must be attached on the base unit (P.1504) for
1011
11
R1 P R2
10
A A
56.5
connection. Can not be directly connected to the solenoid valve. For R2 A A
2-Ø2.8 2-Ø2.8
P
28
20.5
38
27.5
36 14.8 36 44.8 R1 P R2
10
using this type, please purchase base unit separately. B B B B
7.5
(4.3)
(4.3)
• Base Plumbing Type
• External dimensions of this type are the same as those of Direct Connection Type.
95.6 125.6
14
17.9 17 17 17 19 17.5 17.5 17.5
17.6
QPrecautions for Use
I I I
(31.8)
16.516.5 2x3-Rc1/8 26.4 17 17 17
27.5
27.5 20 20
I I I
2x3-Rc1/4
(31.8)
• Use the solenoid valves at temperatures between 5 and 50 °C. Avoid any use and storage in a corrosive atmosphere.
(31.8)
27.5
27.5
• Do not use the solenoid valves in such locations as where water or oil splash and dusty area. 33.5 39 K
5
5
• Fluid Quality 60
• When compressed air is used as a fluid, remove drainage and dust through an air filter.
2-M3x0.5 Depth 5 13.5 26 2-M3x0.5 Depth 5 13.5 56
eThe solenoid valves of M5 Type are located
• Can be used without lubrication maintenance. Use turbine oil "ISO VG32" if any lubricant is to be added.
on the opposite of those of RC1/8 Type.
• Continuous Current 13.6 13.6
• If a valve is continuously energized for long periods, heat generation of the coil may result in reduced
1.6
performance and shorter service life. Please set the valve to make the nonenergized period longer.
M5 Type
Specify only for Base + Solenoid Valve Type Rc1/8 Type M5 Type Rc1/8 Type
15
• Installation Part Number Solenoid
• The valve must be installed by mounting the body and must not be supported by the plumbing.
R1 P R2 62.8 1 ~ 12 Position Base Base Base Additional Price for Solenoid Valve Base Additional Price for Solenoid Valve
• Maintenance Number Solenoid Solenoid Valve L Valve
K Mass L K Mass Mass (g) Unit Unit
• Before the maintenance, be sure that you have turned off the power, stopped the compressed air supply, and no residual pressure left.
Type of
(g) (g) Price S (Single) D (Double) Price S (Single) D (Double)
• Do not disassemble the solenoid valves. Positions Valve Type Voltage (V)
A Accessory: Base Plumbing Type only: Gaskets (NBR) / Mounting Screws (SS400 Nickel Plating)
Lead Wire: 500mm 1 30 42 140 32 42 217
2 47 59 203 49.5 59.5 303
Valve QBasic Specifications of Solenoid Valves
Part Number Unit Price 3 64 76 266 67 77 387
Connection Dia. M5 Rc1/8 (Base + Solenoid
Type Connection Dia. Solenoid Plumbing Method Voltage (V) M5 Type Rc1/8 Type Effective Sectional Area 3.8mm2 13mm2 Valve Type) 4 81 93 329 84.5 94.5 474 (M5)
S (Single Valve Type Pilot-Operated, 5-Port MSSY (M5) 5 98 110 392 102 112 558 Single 68
A (24VDC)
SY (M5) Solenoid) No Symbol (Direct Connection Type) Number of Ports 5 A (24VDC) Double 80
MD MY (Rc1/8) B (100VAC) Number of Positions 2 MSMY (Rc1/8) 6 S (Single)
B (100VAC)
115 127 455 119.5 129.5 640
D (Double M (Base Plumbing Type) Applicable Fluid 7 D (Double) C (200VAC) 132 144 518
C (200VAC) Air
(Base only) (Rc1/8)
Solenoid) Operating Pressure 0.15~0.7MPa 8 149 161 581 Single 68
Pressure Resistance 1.0MPa MSSYB (M5) 9 166 178 644 Double 87
Part Number Valve Voltage Response Time 30ms 19ms MSMYB (Rc1/8) 10 - - - -
- Operating Temp. Range 5 ~ 50°C 183 195 707
Type Connection Dia. Solenoid Plumbing Method (V) Rated Voltage 24VDC,100VAC,200VAC 11 200 212 770
Power Consumption 2.1/1.8VA(50/60Hz:AC), 1.6W(DC) 1.6/2.5VA(50/60Hz:AC), 1.2W(DC)
MD SY S - A Allowable Voltage Range ±10% 12 217 229 833
MD MY D M - C Insulation Class B Type F Type
QFlow Rate Characteristics Connection Dia.: M5 Part Number - 1 Position - 2 Positions - 3 Positions - 4 Positions - ••• - 12 Positions
Effective Sectional Area: 3.8mm2
0.8 MSSY12 - SA - DA - DC - SB - •••
- DB
0.7 MSMY3 - SA - DA - DC
Supply Pressure MSSYB6
Secondary Pressure [MPa]
0.6
0.7
0.5
0.6
0.4
0.5
0.3
0.4
0.2
0.2 0.3
QCross Section Structure Diagram * The figures below are for Direct Connection Type, but the components are in common with the Base Plumbing Type. 0.1
0 Number of Positions
Single Solenoid Double Solenoid 0 50 100 150 200 250 300 350 400
• M5 Type • Rc1/8 Type 1
Flow Rate Q [L/min(ANR)] 2 3 ••••••
8 7 1 6 3 4 5 2 9 10 7 1 6 3 4 5 2 9 10 Connection Dia.: Rc1/8 2
• For MSSY and MSMY, the base and the solenoid valve will be assembled before shipping. R1 P R2 R2 P R1 6 15 17 17 15 6
MSSYB and MSMYB are the base only, which are designed to be combined with the Base Plumbing Type of the solenoid valve on the left-hand page.
Effective Sectional Area: 13mm
0.8 • Plug Plug
Secondary Side Pressure [MPa]
0.7
Supply Pressure (Assembly is required by the customer.) SOL.a SOL.b SOL.a SOL.b
0.6 • For the Basic Specifications, the Flow Rate Characteristics and the Cross Section Structure Diagram, see the left-hand page.
0.7 A B B A
0.5
0.6 SOL.a
0.4
0.3
0.5 QConfiguration of Parts (MSSY, MSMY) QParts Material Table 4-Ø4.5
0.4
0.2
0.3
Part Number Name MMaterial Double Solenoid Double Solenoid
0.2 Base A6061
0.1 3 1
QComponent List
0 2 Gasket NBR A B B A
16
0 200 400 600 800 1000 1200 1400
60
Flow RateQ [L/min(ANR)] 3 Set Screw SS400
Part Number Name MMaterial Part Number Name MMaterial 2
33.5
4 Plug Nickel Plating
1 Main Body A6061 6 Spool Valve A6061 eCheck for the following when operating condition Single Solenoid
4 R1 P R2 Single Solenoid
2 Pilot Body PBT 7 Spool Valve Gasket NBR is poor.
3 Piston POM 8 End Cover PBT • Whether the operating pressure is 0.15 ~ 0.7MPa. 1 R1 P R2 R2 PSOL.b
R1
4 Piston Gasket NBR 9 Coil (Not operational at less than 0.15MPa.)
5 Push Button POM 0 Connector Cord • If operated within the range of rated voltage.
2 -1503 2L -1504
Single Solenoid Double Solenoid
82 112
26 56 56 56 15 15
(4.3)
(4.3)
(4.3)
(4.3)
2x Number of Positions -Rc1/8