Professional Documents
Culture Documents
Codel GCEM 40
Manufactured by:
Certification ranges:
CO 0 to 500ppm 0 to 1000ppm
NO 0 to 500ppm 0 to 1000ppm
SO2 0 to 500ppm 0 to 1000ppm
Page 1 of 8
Form 1335
Issue 10
Certificate Contents
Approved Site Application ........................................................................................................ 2
Basis of Certification ............................................................................................................... 2
Product Certified..................................................................................................................... 3
Certified Performance ............................................................................................................. 4
Description............................................................................................................................. 8
General Notes ........................................................................................................................ 8
Any potential user should ensure, in consultation with the manufacturer, that the monitoring system
is suitable for the intended application. For general guidance on monitoring techniques refer to the
Environment Agency Monitoring Technical Guidance Notes available at www.mcerts.net
On the basis of the assessment and the ranges required for compliance with EU Directives this instrument is
considered suitable for use on waste incineration and large coal-fired combustion plant applications. This CEM
has been proven suitable for its measuring task (parameter and composition of the flue gas) by use of the QAL
1 procedure specified in EN14181, for LCPD/IED Chapter III and IED Chapter IV applications for the ranges
specified. The lowest certified range for each determinant shall not be more than 1.5X the daily average
emission limit value (ELV) for IED Chapter IV applications, and not more than 2.5X the ELV for IED Chapter
III and other types of application.
The field test was carried out over a period of 4 months and 10 days in the exhaust gas of a coal
fired power plant upstream of desulphurization.
Basis of Certification
This certification is based on the following Test Report(s) and on Sira’s assessment and ongoing
surveillance of the product and the manufacturing process:
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 2 of 8
Product Certified
The Data Display Unit (or DDU) is the customer interface providing the flowing;
1. 5 x 4 to 20ma outputs
2. 5 x volt-free SPCO contacts
3. 1 x volt-free SPCO contact for Data Valid
4. 1 x RS485 Modbus output
5. 1 x 2 line display
1. 507-108A DDU
2. 507-066A Transceiver Head Slave
3. 507-067A Transceiver Head Master
4. 507-065A Controller Master
This certificate applies to all instruments with following Serial number onwards;
GCEM40 -1000
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 3 of 8
Certified Performance
The instrument was evaluated for use under the following conditions:
CO 0.0 <2.0%
NO 0.1 <2.0%
CO 0.2 <2.0%
NO 0.3 <2.0%
Lack-of-fit
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 4 of 8
Test Results expressed as % of the Other results MCERTS
certification range specification
<0.5 <1 <2 <5
Influence of ambient temperature zero
point
(-20°C to +50°C)
CO 0.2 <5.0%
NO 1.0 <5.0%
CO 1.8 <5.0%
NO 1.6 <5.0%
CO 0.37 <2.0%
NO -0.29 <2.0%
CO -0.2 <2.0%
NO 0.5 <2.0%
CO 0.4 <2.0%
NO -0.4 <2.0%
O2 0.8 <2.0%
CO 0.0
NO -0.1
SO2 0.1
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 5 of 8
Test Results expressed as % of the Other results MCERTS
certification range specification
<0.5 <1 <2 <5
Influence of vibration Span point
CO -1.1
NO -1.6
SO2 1.8
CO 0.0 <4.0%
NO 0.0 <4.0%
CO 1.4 <4.0%
NO -1.8 <4.0%
CO 0.91 >0.90
NO 0.94 >0.90
CO 182s <200s
NO 189s <200s
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 6 of 8
Test Results expressed as % of the Other results MCERTS
certification range specification
<0.5 <1 <2 <5
Lack of fit (field)
CO 1.2 <2.0%
NO -1.4 <2.0%
CO 1.4 <3.0%
NO 3.0 <3.0%
CO 3.0 <3.0%
NO 2.9 <3.0%
Availability
97.1% >95%
Reproducibility
CO 0.8 <3.3%
NO 1.6 <3.3%
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 7 of 8
Description
The AMS Codel GCEM 40 Series is an IR analyser; it uses an insitu probe set into the flue gas duct
or stack to measure the emission levels of the selected gases within the flue gas. The probe includes
a measurement cell that allows flue gas to diffuse into the optical measurement path of the analyser.
A transceiver unit mounted on the probe transmits a beam of infrared energy down the probe through
the measurement cell to a reflector that directs the beam back to the transceiver. Analysis of the
received energy beam by NDIR technology provides a continuous measurement of the levels of the
selected emissions within the flue gas.
General Notes
1. This certificate is based upon the equipment tested. The Manufacturer is responsible for
ensuring that on-going production complies with the standard(s) and performance criteria
defined in this certificate. The manufacturer is required to maintain an approved quality
management system controlling the manufacture of the certified product. Both the product
and the quality management system shall be subject to regular surveillance according to
‘Regulations Applicable to the Holders of CSA Group Testing UK Ltd Certificates’.
2. The design of the product certified is held and maintained by TUV Rheinland for certificate No.
Sira MC160296/01.
3. If a certified product is found not to comply, CSA Group should be notified immediately at the
address shown on this certificate.
4. The certification marks that can be applied to the product or used in publicity material are
defined in ‘Regulations Applicable to the Holders of CSA Group Testing UK Ltd Certificates’.
5. This document remains the property of CSA Group and shall be returned when requested by
CSA Group.
This certificate may only be reproduced in its entirety and without change
To authenticate the validity of this certificate please visit www.csagroupuk.org/mcerts
Page 8 of 8