Professional Documents
Culture Documents
The vents are driven on the basis of a ventilation temperature to be reached. The basis for
this ventilation temperature is the set 24-hour cycle of I120 Ventilation strategy divided
across a maximum of 6 periods.
The calculated vent position for the lee side and the wind side may vary between the
maximum and the minimum vent position, which is adjustable per maximum of 6 periods
(again).
1 Period
Adjustable period for the vent settings based on time settings.
2 Activated
Indication the vent period is active.
3 Period
Option whether the vent period is to be included in the 24 hour division.
4 Start time
Start time of the vent period.
The calculated maximum vent position can vary from the maximum vent position specified
here through limits such as rain, wind speed and humidity.
The calculated minimum vent position is composed of a set minimum vent position and a
humidity-dependent minimum vent. The minimum vent position can be decreased due to
weather conditions.
The calculated maximum vent position can vary from the maximum vent position specified
here through limits such as rain, wind speed and humidity.
9 P band lee
The P band is a temperature range from the calculated ventilation temperature, within
which the vents move from closed (0%) to open (100%). The smaller the P band, the faster
the vents react to a change in the measured greenhouse temperature. See also Ventilation .
When P band has been set at 0.0 °C, the applicable P band is 0.5 °C.
The calculated ventilation temperature for the lee side can be seen in M120
Overview ventilation .
The following applies when outside temperatures are low (to 8 °C for example):
Max P band lee.
The following applies when outside temperatures are high (from 16 °C for
example): Min P band lee.
An intermediate P band is calculated for temperatures in between.
11 P band wind
The P band is a temperature range from the calculated ventilation temperature, within
which the vents move from closed (0 %) to open (100 %). The smaller the P band, the
faster the vents react to a change in the measured greenhouse temperature.
When P band has been set at 0.0 °C, the applicable P band is 0.5 °C.
The calculated ventilation temperature for the wind side can be seen in M120
Overview ventilation .
The following applies when outside temperatures are low (to 8 °C for example):
Max lagging wind.
The following applies when outside temperatures are high (from 16 °C for
example): Min P band wind.
An intermediate P band is calculated for temperatures in between.
11 Max P band wind
The P band is a temperature range from the calculated ventilation temperature, within
which the vents move from closed (0 %) to open (100 %).
If the lagging wind is set to less than 0°C, the lee side will lag behind the wind side: vents
on the wind side will open first.
The calculated lagging varies between the set Min lagging wind and the set Max lagging
wind based on the weather influences (I125.2).
If Max lagging wind is set to a value lower than 0°C, then Min lagging wind must
also be set less than or equal to 0°C.
When the vents have been controlled open, for example to discharge humidity, the
measured temperature may fall. As a result the water temperature can be increased. This
extra heat will be loss through the open vent. By closing the vents a little instead of
increasing the minimum water temperature, the temperature in the greenhouse will not fall
any further or will even increase slightly.
By entering the setup table you can prevent the measured temperature from falling below
the heating temperature. You can enter:
Same as Dev. temp : adjustment min vent lee, but for the wind side. You can enter:
In Priva Office Direct, you can see which Extra influence has been set in the
window of the setting table.
NONE The calculated maximum vent positions on the lee and the wind side are not
decreased depending on the humidity.
INSIDE The maximum vent position on the lee side and the wind side is decreased by
the humidity measured inside.
OUTSIDE The maximum vent positions on the lee and the wind side are decreased by the
humidity and/or wind direction measured outside.
BOTH The maximum vent positions on the lee and the wind side are decreased by the
humidity and/or wind direction measured inside and/or outside.
The humidity influence on the calculated maximum vent position can be set in
I125.3.
The influence of the wind direction on the calculated maximum vent positions can
be set in I125.2.
24 Weather influence min vent
For each period, you can set whether the weather conditions should influence the calculated
minimum vent positions.
The size of this weather influence appears in I125.2: Calculated weather influence. This
selection determines how this weather influence to be processed:
NO no weather influence
SET weather influence on the set min vent (lines 6 and 8)
HUMIDITY weather influence on the humidity-dependent set min vent (lines 15 and 16)
SUM weather influence on both the set min vent and the humidity-dependent set
min vent
If Air inlet F&P cooling is MOD or NONE, then the minimum vent positions can be
limited if the following conditions apply:
1 VENT CONTROL
Number of the vent control.
One application of this, for instance, is drying after a rain shower. The opening of the vents
can be delayed, so that excessive opening can be prevented and an equilibrium situation is
achieved more quickly.
The time can be adjusted to the measured outside radiation. The greater the amount of
radiation, the shorter the time per 10% adjustment.
If the wind direction is between the ridge direction and Range infl. wind dir.
on lagging start (dealer setting), the calculated lagging is equal to the
minimum lagging.
If the angle between the wind direction and the ridge direction is greater than
Range infl. wind dir. on lagging end (dealer setting), the calculated lagging is
equal to the calculated lagging without the influence wind direction.
Between these positions, the calculated lagging increases proportionally.
Lagging based on wind direction is only possible when a modulating wind direction
sensor is used.
Old situation (before wind shift over the New situation (after wind shift over the ridge
ridge direction) direction)
Vent position on the wind side less than The vents on both sides move immediately to
Limitation vent lee switch over wind the new desired positions.
Vent position on the wind side greater The vent on the (old) lee side is closed first to
than Limitation vent lee switch over wind below Limitation vent lee switch over wind.
Before selecting YES here, check that the wash robot is no longer on the vents of
the section concerned.
NONE means that the calculated vent adjustment is controlled without delay.
The Storm condition (I120) displays the storm limit to which this vent control is connected.
The storm limits can be set in I4 Weather settings and/or I4.1 Weather extra limits .
In I4.4 Weather allocate extra limits you can determine which storm limit is
connected to the vent control.
The rain quantity never decreases the maximum vent position when rain any further
than the set maximum vent position when rain with maximum wind speed.
The rain quantity never decreases the maximum vent position when rain any further
than the set maximum vent position when rain with maximum wind speed.