Professional Documents
Culture Documents
SPRAY PRODUCTS
spray.com
THANK YOU FOR
YOUR INTEREST IN
OUR SPRAY PRODUCTS
Our high-quality spray products that can help you improve your car wash operations are available from most
OEMs or aftermarket suppliers.
TABLE OF CONTENTS
Introduction A2
Technical Reference A4
Spray Nozzles B1
Spray Guns C1
Air Nozzles D1
Accessories E1
Index i-1
A1
INTRODUCTION
• Lost customers as a result of a poor quality wash or • Additional power used by pump equipment to keep up with
excessive downtime higher flow rates or pressure losses
• Excessive wastewater and disposal costs • Unnecessary labor from increased maintenance
By optimizing your spray system, you can turn these unnecessary expenses into savings opportunities.
A2 spray.com | 1.630.665.5000
INTRODUCTION
Annual cost of wasted water and chemical: $24,314* Wasted chemical: 1,164 gal
Annual cost of wasted water and chemical: $12,157* *Based on US dollar and applications
spray.com | 1.630.665.5000 A3
TECHNICAL REFERENCE
Spray Page
Spray Pattern Application Nozzles
Angle Number
FULL CONE
Uniform, round and full Presoak and covering
15°
spray pattern with medium larger areas. B2
to 125°
to large drops. Good for
covering larger areas.
FullJet®
Chemical arches
FLAT SPRAY or anywhere spray
15°
Overlapping or aligning spray nozzles are aligned to
to 110° B11
patterns from adjacent sprays overlap to produce a
produces uniform distribution. uniform distribution.
VeeJet®
DEFLECTED NON-TAPERED
Rinse arches and presoak,
FLAT SPRAY
especially when recycled
Medium-sized drops at lower 15°
water is being used. Excellent for B16
pressures with narrower spray to 50°
any application in which adjacent
angles. High impact. Large free
spray patterns do not overlap.
passage reduces clogging. P FlatJet®
WashJet
SELF-ASPIRATING
Flat spray pattern, mixes surrounding
air with premixed liquid to generate
0°
foam. Medium to medium-fine foam Detergent application B22
to 80°
stays on vehicle longer. Keeps energy
costs down because compressed air
is not required. FoamJet®
A4 spray.com | 1.630.665.5000
TECHNICAL REFERENCE
Pressure: low
Flow Rate: high
VeeJet B11
Undercarriage Impact: medium
FlatJet® B16
Angle: medium
Drop Size: large
Pressure: high
Flow Rate: medium
Wash Impact: high WashJet® B4
Angle: narrow
Drop Size: large
Pressure: low
Flow Rate: high
VeeJet B11
Rinse Impact: medium
FlatJet B16
Angle: medium
Drop Size: large
Pressure: low
Flow Rate: low
Wax Impact: low VeeJet B11
Angle: medium
Drop Size: fine
Pressure: low
Flow Rate: low
VeeJet B11
Final Rinse Impact: low
FloodJet B18
Angle: medium to wide
Drop Size: fine
Pressure: high
Flow Rate: low to medium
Self-Serve Impact: high WashJet B4
Angle: narrow
Drop Size: medium to large
spray.com | 1.630.665.5000 A5
TECHNICAL REFERENCE
The cleaning effectiveness of a spray nozzle, impact, or the droplets, which have less mass and velocity, and therefore
total force of the spray as it hits the vehicle, are the main less cleaning impact. As a general rule of thumb, increasing
criterias to evaluate spray pressure and impact. The true flow rate is much more effective than increasing pressure.
measure of cleaning effectiveness is impact per square inch. Doubling the flow rate increases impact as much as 100%,
Maximizing the cleaning impact involves increasing both the while doubling pressure provides only 40% more impact.
mass of the spray and its velocity, which is accomplished by The downside of increasing flow rate is increased water
increasing flow rate in gallons (liters) per minute, droplet size consumption, and the biggest operating cost today for a
or psi (bar). car wash is water. At a time when sustainability, water
Most people only think about spray pressure when it conservation and lower operating costs are high priorities,
comes to impact, but increasing pressure can sometimes it is possible to increase pressure and maintain cleaning
be counterproductive. High pressure produces smaller effectiveness with premium, high-pressure nozzles.
I = K x Q x √P
I Total theoretical spray impact kg 0.95 gpm 0.95 gpm 1.9 gpm
Flow Rate
(3.6 lpm) (3.6 lpm) (7.2 lpm)
K Constant .0526
400 psi 800 psi 400 psi
Q Flow rate lpm Pressure
(28 bar) (55 bar) (28 bar)
P Liquid pressure bar Total
Theoretical
1.0 lbs 1.4 lbs 2.0 lbs
Spray Impact
(.07 bar) (.10 bar) (.14 bar)
UNIT IMPACT PER SQ. INCH OF A FLAT FAN
SPRAY PATTERN AT 12" FROM THE NOZZLE
40% 100%
15° 30%
25° 18%
35° 13%
40° 12%
50° 10%
65° 7%
80° 5%
A6 spray.com | 1.630.665.5000
TECHNICAL REFERENCE
SPRAY DISTANCE
Final Rinse
KNOW THE ANGLES, 40° to 110°
WASH STAGES AND
RECOMMENDED Wax
ANGLE RANGE 25° to 65°
Rinse
40° to 80°
Wash
50° to 110°
Undercarriage
50° to 110° Touchless
In-Bay Automatic Self-Serve
Presoak 5° to 15° 25° to 40°
50° to 110°
spray.com | 1.630.665.5000 A7
TECHNICAL REFERENCE
1. INCORPORATE NOZZLE INSPECTION INTO clogged, the spray pattern is destroyed. Streaks develop
YOUR REGULAR MAINTENANCE PROGRAM and the spray will be heavier or lighter throughout the
Damaged spray nozzles waste water and chemicals, pattern. The result is inadequate or inconsistent coverage
decrease cleaning coverage of the vehicles and increase of the vehicle. Customers will experience uneven cleaning
workload on your pumps. With thousands of dollars of profits or drying, so you’ll want to make sure your nozzles are
at stake, you’ll want to regularly monitor your spraying replaced before reaching this point. Customer satisfaction
system to reveal potential problems. Some nozzle problems, and retention depends on it
like corrosion or caking, are easy to detect with a visual • Flow rate change. If you have a centrifugal pump,
inspection, but a worn nozzle, the most common problem an increased flow rate indicates nozzle wear. System
for a car wash, is almost impossible to detect with the pressure will remain the same, enabling you to retain
human eye. some quality in your wash, but your system will be highly
Watch for these clues to indicate spray nozzle problems: inefficient, wasting costly water and chemicals
1 2 3
Spray a new nozzle Measure out Divide the amount
into the container the amount of water by the
for a measured of water into the collection time.
amount of time. measuring cup. This will give you
the gallons per
minute rate of the
new spray nozzle.
A8 spray.com | 1.630.665.5000
TECHNICAL REFERENCE
it should be done with materials that are much softer than for strength and corrosion resistance. The screen is critical
the nozzle orifice. Use toothbrushes, toothpicks or even to the operation of the strainer, and an extra screen should be
compressed air. Never use wire brushes, pocket knives or kept on hand for each strainer installed.
welder’s tip cleaning rasps. It is easy to damage the critical
orifice shape (or size) and end up with distorted spray
patterns or excess flow. If you are faced with a stubborn
clogging problem, soak the orifice in a non-corrosive
cleaning chemical to soften or dissolve the substance.
4 5
Take a baseline Repeat the test periodically on the same
measurement using nozzles and record the date or number
a new nozzle in of wash cycles since the previous test.
each section of As the nozzles begin to wear,
your car wash. the flow rate will increase.
Creating a log will help you
determine how quickly your
nozzles are wearing.
spray.com | 1.630.665.5000 A9
TECHNICAL REFERENCE
Unclogged Spray
APPROXIMATE ABRASION RESISTANCE RATIOS
ACCIDENTAL DAMAGE
Brass 1 Damage can occur if a spray nozzle
is dropped or scratched during
installation, operation or cleaning.
PVDF 3
This is a common occurrence in
self-service car washes, since many New
Stainless Steel 4–6 customers often let spray wands fall Damaged
onto, or scrape against, the concrete
floor of the bay.
Hardened Stainless Steel 10 – 15
New Corroded
Caked
IMPROPER ASSEMBLY
Some spray nozzles require careful re-assembly after WEAR LIFE: PUTTING NOZZLES
cleaning so that internal components such as gaskets, TO THE TEST
O-rings and vanes are properly aligned. Improper positioning
Most high-pressure nozzles are currently constructed of
or even over-tightening of nozzle caps can strip threads and
hardened stainless steel, however, not all manufacturers
can cause leaking and inefficient spray performance.
use the same hardening process, which can lessen the
Improper Assembly
durability of the material. To prove this point, we tested
our WashJet® nozzles, made of hardened stainless steel,
against a competitor’s similar nozzle. The competitor’s nozzle
reached a 10 percent wear point more than twice as fast as
the WashJet nozzle.
Nozzles with ceramic orifices are able to withstand harsh
cleaning chemicals and high temperatures. Nozzles
constructed of PVDF, a very tough plastic material, are good
Proper Assembly
choices for high-temperature wax sealing applications.
CAN I USE A STANDARD “FAN” NOZZLE FOR AFTER A CAR PASSES THE FOAM STICKS ON
THE HIGH-PRESSURE WASH PORTION OF MY MY CONVEYOR, THE FOAM DRIPS OUT THE
CAR WASH? BOTTOM HOLE AND ALL THAT CHEMICAL IS
A standard VeeJet® or UniJet® “fan” type nozzle is not the WASTED. HOW CAN I SOLVE THIS PROBLEM?
best choice for high-pressure applications. The orifice is Normally, we would recommend that every nozzle in your
designed to provide a great spray pattern at lower pressures. entire system has a check valve installed immediately behind
The WashJet® product line, however, was designed it. That way, after the car passes and the pressure in the
specifically to operate in high-pressure applications and arch drops, the check valve shuts off preventing all the water
will provide improved cleaning effectiveness and a better and chemical from draining out. An additional benefit is that
distribution of impact across the entire spray pattern. when the next car comes down the line, your arch is already
filled and the nozzles spray immediately. Unfortunately, it
is extremely difficult to use either an in-line or diaphragm
HOW OFTEN SHOULD I REPLACE MY
type check valve on pre-generated foam. It just does not
SPRAY NOZZLES?
work well. One alternative is to replace your foam sticks
Depending on your system, we would suggest cleaning with FoamJet® nozzles. These nozzles are self-aspirating
your spray nozzles every couple of months and replacing and generate the foam after the liquid passes the check
them every 6 to 12 months. Preferably, you want to replace valve. This gives you the added benefit of eliminating your
them right before the season in which your business picks compressed air requirement and allows you to control the
up. It is difficult to determine when your wash needs new foam’s capacity and spray angle.
nozzles because it depends on so many factors. How good
is your filtration or recycling system? How corrosive are
your chemicals? At what temperature and pressure are you I HAVE SEEN A LOT OF PLASTIC NOZZLE TIPS
spraying? All these factors affect how your nozzles wear. AVAILABLE, BUT I AM CONCERNED ABOUT
When you replace your nozzles, take note of the difference WHERE TO USE THEM. WHAT ARE THE BEST
in spray appearance, pressure reading for your system and APPLICATIONS FOR PLASTIC NOZZLES IN MY
the flow rate. You might be surprised at how much waste in CAR WASH?
water and chemical your car wash was operating with before Plastic nozzles are perfect solutions to low pressure
the replacement. applications with corrosive chemicals. Constructed of
molded PVDF, the plastic VeeJet spray nozzles are more
economical than metal nozzles, withstand a variety of
MY WATER BILL IS GOING UP AND MY
temperature ranges, and are resistant to acids, bases and
BOTTLE CHECK TESTS SHOW THAT MY FLOW
oxidizing agents. Additionally, they are rated up to 500 psi
RATE IS UP, BUT MY NOZZLES ARE FINE
(34.5 bar) and have a surprisingly high wear resistance. You
AND THE SPRAY PATTERN LOOKS NICE AND
can confidently use plastic nozzles in the presoak, rinse and
CLEAN. WHAT IS GOING ON?
wax sections of your wash.
Simply put, your nozzles are wearing normally. A nozzle can
be spraying up to 30% over capacity with no streaks or other
visual problems. Close monitoring and maintenance are
critical to understanding what happens to the nozzles in your
system over time. SPRAY TIP:
If your fluid system has a lot of
twists and turns, request nozzles
with stabilizer vane inserts to
reduce turbulence and deliver
more cleaning impact.
page
FullJet® Nozzles B2
WashJet® Nozzles B4
Foaming B22
Retainers B25
Valves/Stabilizers B26
Strainers B27
B1
FULL CONE
FULLJET ® NOZZLES
SPRAY
• Presoak
• Areas requiring
good coverage
GG GG-W HH
1/8" to 1/4" male conn. 1/8" to 1/4" male conn.Removable 1/8" to 1/4" male conn.
Removable cap and vane cap and vane One-piece body
MATERIAL OPTIONS
Material Code
Brass (none)
Mild Steel I
ORDERING INFORMATION
FULLJET GG, GG-W, HH AND HH-W
Example
Inlet Nozzle Material Capacity
Conn. Type – Code Size 1/4 GG – SS 10
BSPT connections require the addition of a “B” prior to the inlet connection.
B2 spray.com | 1.630.665.5000
FULL CONE
FULLJET ® NOZZLES
SPRAY
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Max. Free Flow Rate Capacity (liters per minute) Spray Angle (°)
Inlet Nozzle Type Orifice
Capacity Passage
Conn. Dia. Nom. 0.4 0.5 0.7 1.5 3 6 7 10 0.5 1.5 6
Size Dia.
(in.) GG HH (mm) bar bar bar bar bar bar bar bar bar bar bar
(mm)
l l 1 .79 .64 – – .38 .54 .74 1.0 1.1 1.3 – 58 53
l l 1.5 1.2 .64 .44 .49 .57 .80 1.1 1.5 1.6 1.9 52 65 59
l l 2 1.2 1.0 .59 .65 .76 1.1 1.5 2.0 2.2 2.6 43 50 46
l l 3 1.5 1.0 .88 .98 1.1 1.6 2.2 3.1 3.3 3.9 52 65 59
1/8
l l 3.5 1.6 1.3 1.0 1.1 1.3 1.9 2.6 3.6 3.8 4.5 43 50 46
3.9 2.0 1.0 1.1 1.3 1.5 2.1 2.9 4.0 4.3 5.1 77 84 79
l l 5 2.0 1.3 1.5 1.6 1.9 2.7 3.7 5.1 5.5 6.5 52 65 59
6.1 2.3 1.3 1.8 2.0 2.3 3.3 4.5 6.2 6.7 7.9 69 74 68
l l 6.5 2.4 1.6 1.9 2.1 2.5 3.5 4.8 6.7 7.1 8.4 45 50 46
1/4 l l 10 3.2 1.6 3.0 3.3 3.8 5.4 7.5 10.3 11.0 13.0 58 67 61
l 12.5 3.2 1.6 3.7 4.1 4.8 6.8 9.3 12.8 13.7 16.2 69 74 68
Maximum Free Passage Diameter is the maximum diameter as listed of foreign matter that can pass through the nozzle without clogging.
Highlighted column shows the rated pressure.
PERFORMANCE DATA:
WIDE ANGLE NOZZLES
Max. Free Flow Rate Capacity (liters per minute) Spray Angle (°)
Inlet Nozzle Type Orifice
Capacity Passage
Conn. Dia. Nom. 0.4 0.5 0.7 1 1.5 3 6 0.4 0.7 6
Size Dia.
(in.) GG-W HH-W (mm) bar bar bar bar bar bar bar bar bar bar
(mm)
l 1.5W 1.2 .64 – – .57 .67 .80 1.1 1.5 – 120 86
l l 2.8W 1.6 1.0 – – 1.1 1.2 1.5 2.0 2.7 – 120 102
1/8 l l 4.3W 2.0 1.0 – – 1.6 1.9 2.3 3.1 4.2 – 120 102
l 5.6W 2.4 1.0 – 1.8 2.1 2.5 3.0 4.0 5.5 – 120 102
l l 8W 2.4 1.3 – 2.6 3.0 3.6 4.3 6.0 8.2 – 120 103
l 10W 2.8 1.3 3.0 3.3 3.8 4.5 5.4 7.5 10.3 112 120 103
1/4 l 12W 3.2 1.3 3.5 3.9 4.6 5.4 6.5 8.9 12.3 114 120 103
l l 14W 3.6 1.6 4.2 4.6 5.3 6.2 7.5 10.2 13.8 114 120 103
Maximum Free Passage Diameter is the maximum diameter as listed of foreign matter that can pass through the nozzle without clogging.
Highlighted column shows the rated pressure.
Based on largest/heaviest version of each type. Based on largest/heaviest version of each type.
spray.com | 1.630.665.5000 D D B3
HIGH PRESSURE
WASHJET ® NOZZLES
FLAT SPRAY
• High pressure, high impact solid stream (0°) or flat fan spray pattern
WashJet Nozzles
• Spray angles of 5° to 80° at operating pressures from 300 to 5000 psi
As the liquid exits
(20 to 345 bar)
through the rounded
• Uniform distribution by using internal guide vane to stabilize U shape of the orifice,
it forms into a flat
liquid turbulence spray pattern. The
• Longer wear life and flow control accuracy with specially hardened distribution is even at
pressures above 300
stainless steel construction psi (20 bar).
• Patented design optimizes fluid dynamics to minimize turbulence and
maximize spray performance
ORDERING INFORMATION
WASHJET MEG, WEG AND IMEG WITH GUIDE VANE
Example
Inlet Nozzle Spray Capacity
Conn. Type – Angle Size 1/4 MEG – 15 04
BSPT connections require the addition of a “B” prior to the inlet connection.
Example
Inlet Nozzle Spray Capacity
Conn. Type – Angle Size 1/4 SAMEG – 15 04
BSPT connections require the addition of a “B” prior to the inlet connection.
B4 spray.com | 1.630.665.5000
HIGH PRESSURE
WASHJET ® NOZZLES
FLAT SPRAY
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
spray.com | 1.630.665.5000 B5
HIGH PRESSURE
WASHJET ® NOZZLES
FLAT SPRAY
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
l 15 15.3 20 24 31 34 40 45 48
l 16 16.3 22 26 33 36 43 48 52
l 20 20 27 32 41 46 54 59 64
l 30 31 40 48 61 68 81 89 97
B6 spray.com | 1.630.665.5000
HIGH PRESSURE
WASHJET ® NOZZLES
FLAT SPRAY
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Spray Angle
Inlet Nozzle Type Flow Rate Capacity (liters per minute)
at 3 bar Capacity
Conn.
Size 20 35 50 80 100 140 170 200 250 275
(in.) IMEG® 5° 10° 15° 25° 40° 50° 65° 80°
bar bar bar bar bar bar bar bar bar bar
l l l 02 2.0 2.7 3.2 4.1 4.6 5.4 5.9 6.4 7.1 7.4
l l l l l l l l l 03 3.1 4.0 4.8 6.1 6.8 8.1 8.9 9.7 10.8 11.3
l l l l l l l l l 035 3.6 4.7 5.6 7.1 8.0 9.4 10.4 11.3 12.6 13.2
l l l l l l l l l 04 4.1 5.4 6.4 8.2 9.1 10.8 11.9 12.9 14.4 15.1
l l l l l l l l l 045 4.6 6.1 7.3 9.2 10.3 12.1 13.4 14.5 16.2 17.0
l l l l l l l l l 05 5.1 6.7 8.1 10.2 11.4 13.5 14.9 16.1 18.0 18.9
1/8, 1/4
l l l l l l l l l 055 5.6 7.4 8.9 11.2 12.5 14.8 16.3 17.7 19.8 21
1/8 25.4 9/16 7.9 0.02 1/8 22.2 1/2 7.9 0.02
MEG IMEG
LL (M)
L LL
(M)
1/4 25.4 9/16 10.3 0.02
1/4 23.0 9/16 10.3 0.02
L
1/4 28.6 5/8 7.9 0.02
L L
c
| 1.630.665.5000
spray.com B7
HIGH PRESSURE
QUICK-CONNECT WASHJET ® NOZZLES
FLAT SPRAY
QCMEG QCIMEG
1/4" quick-connect 1/4" quick-connect
B8 spray.com | 1.630.665.5000
HIGH PRESSURE
QUICK-CONNECT WASHJET ® NOZZLES
FLAT SPRAY
ORDERING INFORMATION
QUICK-CONNECT WASHJET QCMEG AND QCIMEG WITH GUIDE VANE
Example
Nozzle Spray Capacity
Type – Angle Size QCMEG – 15 05
Example
Nozzle Spray Capacity
Type – Angle Size SAQCMEG – 15 05
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Spray Angle
Nozzle Type Flow Rate Capacity (liters per minute)
at 3 bar Capacity
0°* 15° 25° 40° Size 20 35 50 80 100 140 170 200 250 275
QCMEG
(Red) (Yellow) (Green) (White) bar bar bar bar bar bar bar bar bar bar
l l l 02 2.0 2.7 3.2 4.1 4.6 5.4 5.9 6.4 7.2 7.6
l l l l 03 3.1 4.0 4.8 6.1 6.8 8.1 8.9 9.7 10.8 11.3
l l l l l 035 3.6 4.7 5.6 7.1 8.0 9.4 10.4 11.3 12.6 13.2
l l l l l 04 4.1 5.4 6.4 8.2 9.1 10.8 11.9 12.9 14.4 15.1
l l l l l 045 4.6 6.1 7.3 9.2 10.3 12.1 13.4 14.5 16.2 17.0
l l l l l 05 5.1 6.7 8.1 10.2 11.4 13.5 14.9 16.1 18.0 18.9
l l l l l 055 5.6 7.4 8.9 11.2 12.5 14.8 16.3 17.7 19.8 21
l l l 15 15.3 20 24 31 34 40 45 48 54 57
spray.com | 1.630.665.5000 B9
HIGH PRESSURE
QUICK-CONNECT WASHJET ® NOZZLES
FLAT SPRAY
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Spray Angle
Nozzle Type Flow Rate Capacity (liters per minute)
at 3 bar Capacity
10° 15° 25° 40° Size 20 35 50 80 100 140 170 200 250 275
QCIMEG
(Orange) (Yellow) (Green) (White) bar bar bar bar bar bar bar bar bar bar
l l l 02 2.0 2.7 3.2 4.1 4.6 5.4 5.9 6.4 7.2 7.6
l l l l l 03 3.1 4.0 4.8 6.1 6.8 8.1 8.9 9.7 10.8 11.3
l l l l l 035 3.6 4.7 5.6 7.1 8.0 9.4 10.4 11.3 12.6 13.2
l l l l l 04 4.1 5.4 6.4 8.2 9.1 10.8 11.9 12.9 14.4 15.1
l l l l l 045 4.6 6.1 7.3 9.2 10.3 12.1 13.4 14.5 16.2 17.0
l l l l l 05 5.1 6.7 8.1 10.2 11.4 13.5 14.9 16.1 18.0 18.9
l l l l l 055 5.6 7.4 8.9 11.2 12.5 14.8 16.3 17.7 19.8 21
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Spray Angle
Nozzle Type Capacity (liters per minute)
at 3 bar Capacity
Size 20 35 60 80 100 140 170 200
QCEM 25° 50° 65°
bar bar bar bar bar bar bar bar
Net
Length Dia.
Nozzle Nozzle Type Weight
(mm) (mm)
(kg)
DD
QCMEG
LL 31.0 24.6 0.02
QCIMEG
L
VEEJET ® NOZZLES FLAT SPRAY
H-DT H-DU
1/8" to 1/4" female conn. 1/8" to 1/4" female conn.
Flow rates below 1 gpm at 40 psi Flow rates of 1 gpm and greater at 40 psi
(3.8 lpm at 2.8 bar) (3.8 lpm and greater at 2.8 bar)
ORDERING INFORMATION
VEEJET H-DT, H-DU, H-U, H-VV H-VVL
Example
Nozzle Inlet Nozzle Material Spray
Prefix Conn. Type – Code Angle
Capacity
Size H 1/4 VV – SS 110 10
BSPT connections require the addition of a “B” prior to the inlet connection.
VEEJET STRAINER
Example
Strainer Material Mesh
Type – Code – Size 12687 – SS – 100
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
• • 60 4.8 16.8 24 27 34 36 53 61
• • • 70 5.2 19.5 28 32 39 42 62 71
Most capacities may be available in the following spray angles: 0°, 15°, 25°, 40°, 50°, 65°, 80°, 95° and 110°
Highlighted column shows the rated pressure.
L
H-DT H-VV
L L LL
(F) (M)
1/4 19.8 5/8 0.02 1/4 23.0 9/16 0.02
L L
1/4 31.8 9/16 0.03
L
1/8 25.4 9/16 0.01
LL
H-U Based on largest/heaviest version of each type.
(M)
1/4 25.4 9/16 0.02
L
c
L L
L
c
ORDERING INFORMATION
H-VV
Example
Nozzle Inlet Nozzle Material Spray Capacity
Prefix Conn. Type – Code Angle Size H 1/4 VV – CKY 65 06
BSPT connections require the addition of a “B” prior to the inlet connection.
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
Nozzle
Spray Angle at 3 bar Capacity (liters per minute)
Type
Inlet Capacity
Conn. 80° 110° 120° Size
25° 40° 50° 65° 95° 0.4 0.7 1.5 2 3 4 6 7 15 20 35
(in.) H-VV Light Light Light
Green White Blue Purple Gray bar bar bar bar bar bar bar bar bar bar bar
Green Blue Purple
• • • • • • • • 02 .29 .38 .56 .64 .79 .91 1.1 1.2 1.8 2.0 2.7
• • 025 .36 .48 .70 .81 .99 1.1 1.4 1.5 2.2 2.5 3.4
• • • • • • • • • 03 .43 .57 .84 .97 1.2 1.4 1.7 1.8 2.6 3.1 4.0
• • • • • • • • 04 .58 .76 1.1 1.3 1.6 1.8 2.2 2.4 3.5 4.1 5.4
1/4 • • • • • • • • 05 .72 .95 1.4 1.6 2.0 2.3 2.8 3.0 4.4 5.1 6.7
• • • • • • • • • 06 .86 1.1 1.7 1.9 2.4 2.7 3.4 3.6 5.3 6.1 8.1
• • • • • 07 1.0 1.3 2.0 2.3 2.8 3.2 3.9 4.2 6.2 7.1 9.4
• • • • • • • • • 08 1.2 1.5 2.2 2.6 3.2 3.6 4.5 4.8 7.1 8.2 10.8
• • • • • 10 1.4 1.9 2.8 3.2 3.9 4.6 5.6 6.0 8.8 10.2 13.5
Highlighted column shows the rated pressure.
300
0
75 100 125 150 175 200 225 250 275 300
LIQUID TEMPERATURE (°F) Based on largest/heaviest version of each type.
IDEAL FOR:
• Rinse arches
• Presoak
• Use with recycled water
• Applications where adjacent
spray patterns do not overlap
MATERIAL OPTIONS
Material Code
P
1/4" to 1/2" male conn. Brass (none)
Mild Steel I
ORDERING INFORMATION
FLATJET P
Example
Inlet
Conn.
Nozzle
Type – Material
Code
Spray
Angle
Capacity
Size 3/8 P – SS 50 60
BSPT connections require the addition of a “B” prior to the inlet connection.
PERFORMANCE DATA:
NARROW ANGLE SPRAY
Angle
50 l l l 25 3.0 5.7 7.0 9.9 14.0 15.1 18.0 42 50 59 41.5 42 19.1 .09
l l 10 1.9 2.3 2.8 3.9 5.6 6.0 7.2 18 35 39 36.5 36 15.9 .06
IDEAL FOR:
• Presoak applications
• Final rinse applications
• Foam arches
MATERIAL OPTIONS
Material Code
Brass (none)
K
303 Stainless Steel SS
1/8" to 1/2" (M)
ORDERING INFORMATION
FLOODJET K
Example
Inlet
Conn.
Nozzle
Type – Material
Code
Capacity
Size 1/8 K – SS 2
BSPT connections require the addition of a “B” prior to the inlet connection.
PERFORMANCE DATA:
WIDE ANGLE SPRAY
Nozzle Type Inlet Conn. (in.) Equiv. Flow Rate Capacity (liters per minute) Spray Angle (°)
Capacity Orifice
Size Dia. 0.2 0.5 0.7 1.5 2 3 4 0.5 1.5 4
K 1/8 1/4 3/8 1/2 (mm) bar bar bar bar bar bar bar bar bar bar
l l l 2.5 1.3 – .81 .95 1.4 1.6 2.0 2.3 98 122 133
l l l 5 1.9 1.0 1.6 1.9 2.8 3.2 3.9 4.6 114 128 142
l l l 7.5 2.3 1.5 2.4 2.9 4.2 4.8 5.9 6.8 101 119 134
l l l 10 2.7 2.0 3.2 3.8 5.6 6.4 7.9 9.1 115 133 145
l l l 12 2.9 2.4 3.9 4.6 6.7 7.7 9.5 10.9 128 139 153
l l l 15 3.3 3.1 4.8 5.7 8.4 9.7 11.8 13.7 98 113 123
l l l 18 3.6 3.7 5.8 6.9 10.1 11.6 14.2 16.4 106 120 131
l l l 20 3.8 4.1 6.4 7.6 11.2 12.9 15.8 18.2 110 122 133
l l 22 3.9 4.5 7.1 8.4 12.3 14.2 17.4 20 113 125 136
l l 24 4.1 4.9 7.7 9.2 13.4 15.5 19.0 22 115 131 144
Inlet Net
Nozzle L Hex.
Nozzle Conn. Weight
Type (mm) (in.)
(in.) (kg)
• Rinse applications
Tip
Retainer
TPU
Spray Tip
T Body
MATERIAL OPTIONS
TPU Spray Tip
+ T Body Spray Tip Bodies
Material
Material
(TT) Use with Code
TPU T TT
screen strainer and
tip retainer
Brass (none) • • •
Nylon NYB • •
ORDERING INFORMATION
UNIJET TPU
BSPT connections require the addition of a “B” prior to the nozzle body inlet connection.
TIP ONLY
Example
Spray Capacity Material
Tip Type – Angle Size – Code
TPU – 110 10 – SS
UniJet nozzle assemblies include a pre-sized wire mesh strainer based on orifice diameter.
When ordering just a UniJet spray tip, the mesh is not included.
See page B27 for mesh selection guide.
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
T (F) + TPU
LL 1/4 40.9 13/16 0.06
TT (M) + TPU
FJ FJP-PP
• 0°, 40° or 80° spray angles • 20°, 40°, 65° or 80° spray angles
• Material: brass • Material: durable, chemically-resistant
polypropylene
• Color-coded insert for easy
capacity identification
FJP-VS QJFJP
• 40° or 80° spray angles • 40° or 80° spray angles
• Material: durable, • Easy installation and maintenance
chemically-resistant with quarter-turn automatic alignment
polypropylene
• Color-coded insert for easy
• With stainless steel orifice capacity identification
BODY OPTIONS
••• •••
•• •• QJ8355-NY-BL QJ8360-NY-BL
8360-1/4-NY-BL 8355-NY-BL Quick-connect Quick-connect
Quick-connect diaphragm check Diaphragm check diaphragm check diaphragm check
valve nozzle body valve nozzle body valve nozzle body valve nozzle body
Inlet: 1/4" (M) NPT/BSPT Inlet: 1/4" or 1/8" (F) NPT/BSPT Inlet: 1/4" (F) NPT/BSPT Inlet: 1/4" (M) NPT/BSPT
Outlet: 1/4" (F) NPT/BSPT Outlet: 11/16" – 16" thread Outlet: QuickJet Outlet: QuickJet
Max pressure: 300 psi (20 bar) Max pressure: 125 psi (9 bar) Max pressure: 300 psi (20 bar) Max pressure: 300 psi (20 bar)
Nylon Nylon Nylon Nylon
•• •• ••• •••
T TT QJ1/4T-NYB QJ1/4TT-NYB
Inlet: 1/4" (F) NPT/BSPT Inlet: 1/4" (M) NPT Quick-connect Quick-connect
Outlet: 11/16" – 16 thread Outlet: 11/16" – 16 thread diaphragm check diaphragm check
valve nozzle body valve nozzle body
Max pressure: 300 psi (20 bar) Max pressure: 300 psi (20 bar)
Inlet: 1/4" (M) NPT/BSPT Inlet: 1/4" (F) NPT/BSPT
Brass, 303 Stainless Steel, Nylon Brass, 303 Stainless Steel, Nylon
Outlet: QuickJet Outlet: QuickJet
Tip retainer choices determined Tip retainer choices determined
by material: For nylon, use by material: For nylon, use Max pressure: 300 psi (20 bar) Max pressure: 300 psi (20 bar)
CP18032-NYB or CP8027 CP18032-NYB or CP8027 Nylon Nylon
• •
QJ17560A-NY-BL QJ22187-
Quick-connect NYB
diaphragm check Quick-connect
valve nozzle body diaphragm side mounting
Fits 1/2", 3/4" or 1" pipe valve nozzle body
Outlet: QuickJet® Fits 1/2", 3/4" or 1" pipe
Max pressure: 300 psi (20 bar) Outlet: QuickJet
Nylon Nylon
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
FJ 45 0.03
L
FJP-PP 39.5 0.01
L
FJP-VS 38 0.01
QJFJP 53 0.02
ORDERING INFORMATION
FOAMJET TIP
Example
Spray
Tip – Spray
Angle
Capacity
Size – Material
Code FJP – 25 04 – PP
BSPT connections require the addition of a “B” prior to the inlet connection.
FOAMJET BODY ASSEMBLY
Example
Nozzle
Body Type – Material
Code
Check
Valve Size QJ8360 – NY – BL 2
BSPT connections require the addition of a “B” prior to the inlet connection.
TIP RETAINERS
CP1325 CP8027-NYB
Holds nozzle assembly together Holds nozzle assembly together
Inlet: 11/16"-16 female thread Inlet: 11/16"-16
Material: Brass, stainless steel female thread
For high pressure applications, Material: Nylon
use 7890 tip retainer
Order CP1325 when replacement
is needed
CP18032A-NYB
MATERIAL OPTIONS
Holds nozzle assembly together
Winged cap allows quick change Material Material Code
of spray tips with no tool required
Brass (none)
Inlet: 11/16"-16
female thread Stainless Steel SS
Material: Nylon
Nylon NYB
QUICK-CONNECT RETAINERS
114445-4-CELR CP114443-4-CELR
Holds nozzle assembly together Holds nozzle assembly together
Use with FJ and FJP FoamJet® Nozzles Use with FJP FoamJet Nozzles
Constructed of acetal (Celcon) for Provides automatic alignment
good strength and chemical resistance Constructed of acetal (Celcon) for
Max Pressure: 300 psi (20 bar) good strength and chemical resistance
Standard gasket constructed of EPDM. Max Pressure: 300 psi (20 bar)
Viton® is optional Standard gasket constructed of EPDM. Viton is optional
To order gasket separately use part number CP19438-VI or CP19438-EPR To order gasket separately use part number CP19438-VI or CP19438-EPR
ORDERING INFORMATION
RETAINERS
Example
Model Material
No. – Code CP1325 – SS
Stainless Steel SS
ORDERING INFORMATION
CHECK VALVE
Example
Model
No. – Opening
Pressure – Material
Code 21950 – 2 – NYB
JET STABILERS
Example
Stabilizer Material Conn.
Type – Code – Size 11370 – SS – 1/8 x 1/8
BSPT connections require the addition of a “B” prior to the inlet connection.
7630 4067
Disc design for use when space is extremely limited Cup design for use when space is limited
Material: 303 stainless steel Material: 303 stainless steel
Mesh: 30, 50, 100 and 200 Mesh: 30, 50, 100 and 200
Stainless Steel SS
Polypropylene PP
ORDERING INFORMATION
STRAINER 4193A
Example
Strainer
Type – Material
Code – Spring Opening
Pressure (psi) – Mesh
Size 4193A – SS – 5 – 50SS
STRAINER 4514
Example
Strainer
Type – Material
Code – Slot
Width 4514 – NY – 10
D
5053 18.4 15.1 0.050 D 4514 16.7 15.1 0.005
L
L
L D
4193A with
20.7 15.1 0.010
D check valve*
*Built-in check valve and stainless steel springs with opening pressures of 0.35, 0.7, 1.5 or 2.8 bar.
page
C1
SPRAY GUNS GUNJET ® AND TRIGGERJET ®
AA70 PW4000AS
Max. operating pressure: Max. operating pressure:
5000 psi (345 bar) 4000 psi (275 bar)
Max. temperature: 300°F (150°C) Max. temperature: 300°F (150°C)
Capacity: 10 gpm (38 lpm) Capacity: 10 gpm (38 lpm)
Material: Brass valve body with Material: Brass valve body with
nylon handle nylon handle
Trigger lock and guard Trigger lock and guard
Designed to withstand high impact Designed to withstand high impact
Ergonomic design with light trigger pull Ergonomic design with light trigger pull
Large grip area to accommodate Bottom trigger pivot and inlet swivel
work gloves rotate freely at high pressures
Vented handle remains comfortable during Handle remains comfortable during
hot spraying operations hot spraying operations
Optional weep feature prevents freezing
PW4000A AA60
Max. operating pressure: Max. operating pressure:
4000 psi (275 bar) 2500 psi (175 bar)
Max. temperature: 300°F (150°C) Max. temperature:
Capacity: 10 gpm (38 lpm) 300°F (150°C)
Material: Brass valve body with Capacity: 6 gpm (23 lpm)
nylon handle Material: Brass or stainless
Trigger lock and guard steel valve body with nylon handle
Designed to withstand high impact Trigger lock and guard
Ergonomic design with light Designed to withstand high impact
trigger pull Ergonomic design with light trigger pull
Handle remains comfortable during Front hose connection keeps grip cool
hot spraying operations
C2 spray.com | 1.630.665.5000
GUNJET ® AND TRIGGERJET ® SPRAY GUNS
AA30A AA30L-PP
Max. operating pressure: Max. operating pressure:
1500 psi (105 bar) 150 psi (10 bar)
Max. temperature: 200°F (93°C) Max. temperature:
Capacity: 5 gpm (19 lpm) 120°F (8.3°C )
Material: Brass valve body with Capacity: 5 gpm (19 lpm)
nylon handle Material: Brass or polypropylene
Trigger lock and guard valve body with nylon handle
Designed to withstand high impact Trigger lock and guard
Ergonomic design with Light trigger pull
light trigger pull Front hose connection
Front hose connection keeps keeps grip cool
grip cool
Optional weep feature prevents freezing
AA30L
Max. operating pressure:
250 psi (17 bar)
Max. temperature:
200°F (93°C)
Capacity: 5 gpm (19 lpm) MATERIAL OPTIONS
Material: Brass valve body with
nylon handle
Material Material Code
Trigger lock and guard
Light trigger pull
Brass (none)
Front hose connection
keeps grip cool
Polypropylene PP
ORDERING INFORMATION
COMPLETE SPRAY GUN ASSEMBLY
Example
GunJet
Type – Inlet
Conn. – Material
Code AA60 – 3/8 – SS
spray.com | 1.630.665.5000 C3
SPRAY GUNS GUNJET ® AND TRIGGERJET ®
SPECIFICATIONS
Max. Operating Max. Adapters/
Capacity Inlet Conn. Outlet Conn. Weight Spare Parts
Model Pressure Temperature Spray Tips Extensions Swivel
(lpm) (in.) (in.) (kg) Kits
(bar) (°C) Connectors
IMEG, MEG
3/8 NPT or 1/4 NPT
AA70 345 38 150 .71 QCIMEG, 20400-1/8F 15950 —
BSPT (F) or BSPT (F)
WashJet
IMEG, MEG,
15250, 20400-
1/4, 3/8 NPT 1/4, 3/8 NPT MEG-SSTC, 9765, 15950, AB-PW4000A-KIT,
PW4000A 275 38 150 .68 1/4M*, 20400-
or BSPT (F) or BSPT (F) QCMEG 21550 AB-PW4000AW-KIT
1/8F*
WashJet
IMEG, MEG,
3/8 NPT or 15250, 20400- AB-PW4000AS-KIT,
1/4, 3/8 NPT MEG-SSTC,
PW4000AS 275 38 150 BSPT (F) .68 1/4M*, 20400- 15950 AB-PW4000ASW-
or BSPT (F) QCMEG
swivel 1/8F* KIT
WashJet
AB60-KIT,
9004-SS, AB60-SS-KIT,
EG UniJet,
9702A, 9702C, AB60W-KIT,
3/8 NPT or 11/16–16 MEG, 14643-1/4,
AA60 175 23 150 .45 9702S, 20400- AB60-20250-KIT
BSPT (F) UniJet THD MEG-SSTC 15950-SS
1/4M*, 20400- AB60-21580-KIT,
WashJet®
1/8F* AB60-21580A-KIT,
AB36533-60-KIT
9004-SS, AB30A-KIT
1/4 NPT or 11/16–16 EG, TG 4676-SS-1/4,
AA30A 105 19 93 .43 9702A, 9702C, AB30AW-KIT
BSPT (F) UniJet® THD UniJet 9765, 11990
9702S, 13781S AB30A-50736-KIT
4673, 6671,
6960, 7715,
TB, TG, TK, AB30L-KIT
1/4 NPT or 11/16–16 9004-SS, 9527,
AA30L 17 19 93 .43 TN, TPU, TX 4676, 20897 AB30L-PP-KIT
BSPT (F) UniJet® THD 9702A, 9702C,
UniJet AB30L-VI-KIT
9702S, 12086,
13781S, 14975
4673, 6671,
6960, 7715,
TB, TG, TK, AB30L-KIT
1/4 NPT or 11/16–16 9004-SS, 9527,
AA30L-PP 10 19 8.3 .43 TN, TPU, TX 4676, 20897 AB30L-PP-KIT
BSPT (F) UniJet® THD 9702A, 9702C,
UniJet AB30L-VI-KIT
9702S, 12086,
13781S, 14975
C4 spray.com | 1.630.665.5000
GUNJET ® AND TRIGGERJET ® SPRAY GUNS
AA31 6466
Max. operating pressure: 500 psi (35 bar) Max. operating pressure: 250 psi (17 bar)
Max. temperature: Max. temperature: 140°F (60°C)
200°F (93°C) Capacity: 2 gpm (7.6 lpm)
Capacity: 5 gpm (19 lpm) Material: Brass or stainless
Material: Brass valve body steel valve body
Optional trigger lock Internal strainer with
choice of mesh sizes
Can be used with air
Extra long trigger
Positive trigger action
for drip-free shut off
4688 6590
Max. operating pressure: Max. operating pressure: 250 psi (17 bar)
250 psi (17 bar) Max. temperature: 140°F (60°C)
Max. temperature: Capacity: 2 gpm (7.6 lpm)
140°F (60°C)
Material: Brass or stainless
Capacity: 2 gpm (7.6 lpm) steel valve body
Material: Brass or Trigger lock
stainless steel valve body
Extra long trigger
Trigger lock
Quick acting “on-off” valve
Trigger designed for ease and
comfort in operation
spray.com | 1.630.665.5000 C5
SPRAY GUNS GUNJET ® AND TRIGGERJET ®
50800-PP-1/4 50800-15-PP-1/4
Max. operating pressure: 100 psi (7 bar) Max. operating pressure: 100 psi (6.9 bar)
Max. temperature: 120°F (50°C) Max. temperature: 120°F (50°C)
Capacity: 1.5 gpm (5.3 lpm) Capacity: 1.5 gpm (5.3 lpm)
Material: Polypropylene valve body Material: Polypropylene valve body
Trigger lock Trigger lock
Polypropylene strainer located Polypropylene strainer located
inside handle to prevent clogging. inside handle to prevent clogging.
22650-PP 22670-PP
Max. operating pressure: 150 psi (10 bar) Max. operating pressure: 150 psi (10 bar)
Max. temperature: 120°F (50°C) Max. temperature: 120°F (50°C)
Capacity: 2 gpm (7.6 lpm) Capacity: 2 gpm (7.6 lpm)
Material: Polypropylene valve body Available with 15” or 24” extensions
Trigger lock Material: Polypropylene valve body
Corrosion-resistant lightweight design Trigger lock
Choice of threaded Corrosion-resistant lightweight design
or hose inlet connection Choice of threaded
UniJet® strainer option or hose inlet connection
UniJet® strainer option
MATERIAL OPTIONS
Aluminum AL
Brass (none)
Polypropylene PP
Stainless steel SS
ORDERING INFORMATION
COMPLETE SPRAY GUN ASSEMBLY
Example
TriggerJet Material Inlet
Model – Code – Conn. 22650 – PP – 1/4
BSPT connections require the addition of a “B” in the prefix of the part number. Example: B22650-PP-1/4.
C6 spray.com | 1.630.665.5000
GUNJET ® AND TRIGGERJET ® SPRAY GUNS
SPECIFICATIONS
Max. Operating Max. Adapters/
Capacity Inlet Conn. Outlet Conn. Weight Spare Parts
Model Pressure Temperature Spray Tips Extensions Swivel
(lpm) (in.) (in.) (kg) Kits
(bar) (°C) Connectors
AB36-KIT,
1/4, 3/8 NPT 1/4, 3/8 NPT HH FullJet®, 20400-1/4M, 4272, 4725,
AA36 10 27 60 .32 AB36-SS-KIT,
or BSPT (F) or BSPT (F) VeeJet® 20400-1/8F 4754, 5820
AB36-21140-KIT
AB31-KIT,
6671-SS, 4676, 7599,
1/4 NPS (M) EG, TB, TG, TK, AB31-39430-
11/16–16 7715-SS, 8603, 8604,
AA31 35 19 93 or NPT or .35 TN, TP, TPU KIT,
UniJet THD 9004-SS, 9527, 11990, 14269,
BSPT (F) UniJet AB31-9525-KIT,
12086, 15699 14643
AB31-PGA-KIT
4673, 6671,
TB, TG, TK, 9004-SS, 9527,
1/4 NPT or 11/16–16 TN, 9702A, 9702C,
4688 17 7.6 60 .14 4676 AB4688-KIT
BSPT (F) UniJet THD TP, TPU, TX 9702S, 12086,
UniJet 13781S,
14975, 15699
FullJets, 20400-1/4M,
1/4 NPT or 1/4 NPT or
6104 17 7.6 60 .14 H-U, H-VV 20400-1/8F, 4676 AB6104-KIT
BSPT (F) BSPT (F)
VeeJet CP12087
4673, 6671,
TB, TG, TK, 9004-SS, 9527,
1/4 NPT or 11/16–16 TN, 9702A, 9702C,
6466 17 7.6 60 .14 4676 AB6466-KIT
BSPT (F) UniJet THD TP, TPU, TX 9702S, 12086,
UniJet 13781S,
14975, 15699
FullJets, 20400-1/4M,
1/4 NPT or 1/4 NPT or
6590 17 7.6 60 .16 H-U, H-VV 20400-1/8F, 4676 AB6590-KIT
BSPT (F) BSPT (F)
VeeJet CP12087
Do not exceed the maximum operating pressure of the lowest rated accessory item within the spray system. Contact your sales engineer for additional configuration options.
See Spraying Systems Co. Hydraulic Spray Products Catalog 75A for spray tip performance data.
spray.com | 1.630.665.5000 C7
SPRAY GUNS GUNJET ® SPRAY EXTENSIONS
203
457 Rubber insulated
11/16–16 11/16–16 (203 mm length
15699 69 Brass 610
UniJet THD UniJet THD not rubber
914 insulated)
1219
203
457
11/16–16 11/16–16 Curved, rubber
9527 69 Brass 610
UniJet THD UniJet THD insulated
914
1219
203
C8 spray.com | 1.630.665.5000
GUNJET ® SPRAY EXTENSIONS SPRAY GUNS
Max.
Extension Inlet Conn. Outlet Conn. Lengths Special
Extension Pressure Material
No. (in.) (in.) (mm) Features
(bar)
381
11/16–16 11/16–16
22665 10 Polyester
UniJet THD UniJet THD
610
203
457
Brass
11/16–16 11/16–16 (914 mm lengths 610
6671 8.6 Curved body
UniJet THD UniJet THD also available in 762
stainless steel)
914
1219
Do not exceed the maximum operating pressure of the lowest rated accessory item within the spray system. Contact your sales engineer for additional options.
MATERIAL OPTIONS
Aluminum AL
Brass (none)
Stainless steel SS
ORDERING INFORMATION
Example
Extension
Type – Extension
Length – Material
Code 7715 – 18 – SS
spray.com | 1.630.665.5000 C9
SPRAY GUNS GUNJET ® SWIVEL CONNECTORS AND ADAPTERS
Max.
Max. Pressure Inlet Conn. Outlet Conn.
Connector Type Temperature Material Special Features
(bar) (in.) (in.)
(°C)
Delrin® bearings
3/8 NPT or
21550-90NP 103 93 1/4, 3/8 NPT (M) and Ceiling-mount.
BSPT (F)
Buna-N O-ring
Max.
Max. Pressure Inlet Conn. Outlet Conn.
Connector Type Temperature Material Special Features
(bar) (in.) (in.)
(°C)
Nickel-plated
11/16–16 THD 1/8, 1/4" NPT
14643 275 – steel or
(F) or BSPT (F)
stainless steel
Do not exceed the maximum operating pressure of the lowest rated accessory item within the spray system. Contact your sales engineer for additional options.
MATERIAL OPTIONS
Brass (none)
Nickel-plated brass NP
Stainless steel SS
Nylon NYB
ORDERING INFORMATION
OUTLET ADAPTER
Example
Adapter Inlet Material
Type – Conn. – Code 4676 – 1/4 – SS
BSPT connections require the addition of a “B” in the prefix of the part number. Example: B15950.
Example
Swivel Material
Type – Code 15950 – SS
BSPT connections require the addition of a “B” in the prefix of the part number. Example: B15950.
Example
Swivel Inlet Outlet
Type – Conn. x Conn. 21550 – 1/4F x 1/4M
BSPT connections require the addition of a “B” in the prefix of the part number. Example: B15950.
11990 DIMENSIONS
page
D1
COMPRESSED
WINDJET ® AIR NOZZLES
AIR
IDEAL FOR:
D2 spray.com | 1.630.665.5000
COMPRESSED
WINDJET ® AIR NOZZLES
AIR
SPECIFICATIONS
At 7 bar
M 1/4 Polyphenylene sulfide (RY) 82
Aluminum (AL) 230
At 7 bar
AA727 M or F 1/4 ABS plastic
77
At 10.3 bar
M 1/4
Stainless steel (SS) 260
At 8.6 bar
Polyphenylene sulfide (RY) 204
PVDF (KY) 104
AA707 M 1/4
Aluminum (AL) 230
Stainless steel (SS) 230
ABS plastic 82
ORDERING INFORMATION
WINDJET AIR NOZZLES
Example
Nozzle
Type – Inlet
Conn. – Material – Capacity
Size AA707 – 1/4 – SS – 11
PERFORMANCE DATA:
STANDARD ANGLE SPRAY
spray.com | 1.630.665.5000 D3
COMPRESSED
WINDJET ® AIR NOZZLES
AIR
A B Net Weight
NozzleType Nozzle Type
(mm) (mm) (kg)
D4 spray.com | 1.630.665.5000
ACCESSORIES
page
Siphon Injectors E2
Check Valves E4
E1
ACCESSORIES SIPHON INJECTORS
SPECIFICATIONS
Max. Inlet Outlet Siphon Inlet Max. Approximate
Model
Pressure Connection Connection Connection Temperature Weight Material
Number
(bar) (in.) (in.) (in.) (°C) (kg)
ORDERING INFORMATION
50580 ADJUSTABLE SIPHON INJECTOR
Example
Model No. – Inlet/Outlet
Conn. – Capacity
Size 50580 – 3/8 – 5
Example
Model No. – Inlet/Outlet
Conn. – Capacity
Size – Siphon
Conn. 50580 – 1/2 – 20 – 1/4
Example
Model No. – Inlet/Outlet
Conn. – Siphon
Conn. – Metering
Orifice 13340 – 3/8 – 1 – 73
BSPT connections require the addition of a “B” prior to the inlet connection.
E2 spray.com | 1.630.665.5000
ADJUSTABLE BALL FITTINGS ACCESSORIES
SPECIFICATIONS
Inlet Outlet Total
Model L D (Dia.) Hex. Net Weight
Conn. Conn. Included Angle
Number (mm) (mm) (in.) (kg)
(in.) (in.) of Adjustment
ORDERING INFORMATION
36275 ADJUSTABLE BALL FITTING
Example
Type – Inlet
Conn. – Outlet
Conn. – Material 36275 – 1/2 – 1/2 – SS
BSPT connections require the addition of a “B” prior to the inlet connection.
spray.com | 1.630.665.5000 E3
ACCESSORIES CHECK VALVES
12328 Diaphragm
1/2”, 3/4” male inlet and
female outlet conn.
MATERIAL OPTIONS Max. flow rate: 15 gpm (57 lpm)
7 psi (0.5 bar) opening pressure
Material Code
Material: Nylon
Brass No code
SPECIFICATIONS
Maximum Maximum Opening Inlet Outlet
Check Spring
Pressure Flow Rate Pressure Connection Connection
Valve Rates
(bar) (l/min) (bar) (in.) (in.)
ORDERING INFORMATION
CV SERIES CHECK VALVE
Example
Inlet/ Opening
Outlet – Check
Valve – Material – Pressure 1/4 ABCV – SS 5
Conn. (psi)
BSPT connections require the addition of a “B” prior to the inlet connection.
Opening pressure is ordered in psi.
BSPT connections require the addition of a “B” prior to the inlet connection.
E4 spray.com | 1.630.665.5000
THROTTLING AND PRESSURE RELIEF/REGULATING VALVES ACCESSORIES
8460 9840
1/2”, 3/4” male inlet and female Diaphragm-style pressure relief valve
bypass conn. Fairprene® diaphragm seal prevents
Diaphragm-style pressure relief valve fluid from working parts and provides
Female pressure gauge port and plug responsive, chatter-free operation.
for use when pressure gauge not used Additional port for pressure
Fairprene® diaphragm seal prevents gauge installation.
fluid from working parts Materials: Aluminum and brass
Materials: Aluminum housing housing with nylon body
with nylon body
6815 110
1/2”, 3/4” male inlet and female 1”, 1-1/4”, 1-1/2” conn.
outlet conn. Piston-type pressure relief valve
Piston-type pressure relief valve Guide vane seat stabilizes flow for
Free-floating design improves speed vibration reduction
and sensitivity Free-floating design improves speed and sensitivity
Full flow with minimum pressure loss Full flow with minimum pressure loss due
due to extra large valve passage to extra-large valve passage
Materials: Aluminum, brass, hardened Removable valve bonnet: no disturbance of
stainless steel fluid line connections
Materials: Aluminum, brass, ductile iron,
hardened stainless steel
Nylon/Aluminum NY
Polypropylene PP
spray.com | 1.630.665.5000 E5
ACCESSORIES THROTTLING AND PRESSURE RELIEF/REGULATING VALVES
SPECIFICATIONS
Up to 20 •
1/4 20 to 48 •
48 to 70 •
Up to 20 •
3/8 20 to 48 •
48 to 70 •
3.5 • •
Up to 10.4 • •
1/2 Up to 20 • • •
20 to 48 • •
48 to 85 • •
Up to 3.5 • •
Up to 10.4 • •
3/4 Up to 20 • • •
20 to 48 • •
48 to 85 • •
ORDERING INFORMATION
PRESSURE RELIEF/REGULATING VALVE
Example
Inlet/ Pressure
Valve Material
Type – Outlet
Conn.
– Code – Rating
(psi) 6815 – 1/2 – AL – 50
BSPT connections require the addition of a “B” prior to the inlet connection.
Pressure rating is ordered in psi.
THROTTLING VALVE
Example
Inlet/
Valve Material
Type – Outlet
Conn.
– Code 23520 – 1/2 – PP
BSPT connections require the addition of a “B” prior to the inlet connection.
E6 spray.com | 1.630.665.5000
THROTTLING AND PRESSURE RELIEF/REGULATING VALVES ACCESSORIES
L
23520
B
3/4 114 – 35.8 57 0.08
W
L
23120
B
A 3/4 133.4 26 60.3 68.3 0.16
9840
L
8460
L 6815
B
3/4 168.3 48.4 69.9 63.5 0.59
spray.com | 1.630.665.5000 E7
TRADEMARK REGISTRATION AND OWNERSHIP
INDEX
HOW TO ORDER
The following is a current list of Spraying Systems Co.'s The following trademarks are registered to other entities
trademarks registered in the United States. Some marks in the US and may be registered in other countries
are registered in other countries as well. as well.
Spraying Systems Co. reserves the right to make changes in specifications or design of the products shown in the catalog
or to add improvements at anytime without notice or obligation.
HOW TO ORDER
In each product section, you’ll find ordering examples. Start by reviewing the example and then create the part number
by indicating the inlet connection, material and capacity size.
Example
GunJet Material Inlet
Model – Code – Conn. 22650 – PP – 1/4
For your convenience, there are multiple ways to place an order: phone, fax and online
In North America
Phone: 1.800.95.SPRAY | Fax: 1.888.95.SPRAY
Outside North America
Phone: 1.630.665.5000 | Fax: 1.630.260.0842
Online ordering with a credit card is also available. Visit spray.com/ispray. You’ll find helpful
selection tools and a Live Chat option for immediate assistance.
FINDING PRODUCTS
• Consult the Product Index on page i-3 if you know the name of the product
• Consult the Part Number Index on page i-4 if you have the part number. Part numbers are shown numerically
and alpha-numerically
Selection assistance is also available by calling 1.800.95.SPRAY. Representatives in your local sales office will help
you determine which products best meet your application requirements. (Call 1.630.665.5000 outside North America
or visit spray.com to find information for the sales office in your area.)
PRODUCT
BALL FITTINGS JET STABALIZERS 6104.................................................. C5, C7
36275....................................................... E3 11370.....................................................B26 6590.................................................. C5, C7
37235....................................................... E3 11950.....................................................B26 22650-PP.........................................C6 - C7
22670-PP.........................................C6 - C7
CHECK VALVES GUNJET SPRAY EXTENSIONS 50800-15-PP-1/4.............................C6 - C7
12328....................................................... E4 6671.........................................................C9 50800-PP-1/4................................... C5, C7
21950.....................................................B26 7715.........................................................C8 AA31................................................C6 - C7
AACV....................................................... E4 9527.........................................................C8 AA36................................................C6 - C7
ABCV....................................................... E4 12086.......................................................C8
BACV....................................................... E4 15699.......................................................C8 UNIJET ® STRAINERS
BBCV....................................................... E4 20400-1/4M.............................................C8 4067............................................ B27 - B28
20400-1/4F...............................................C8 4514............................................ B27 - B28
FLATJET ® NOZZLES 22665.......................................................C9 5053............................................ B27 - B28
P ................................................. B16 - B17 9004-SS...................................................C8 6051............................................ B27 - B28
7630............................................ B27 - B28
FLOODJET ® NOZZLES GUNJET SWIVEL 8079............................................ B27 - B28
K ................................................. B18 - B19 CONNECTORS & ADAPTERS 4193A ......................................... B27 - B28
4676.............................................C11 - C12
FOAMJET ® NOZZLES 9765.............................................. C10, C12 UNIJET NOZZLE
7421............................................ B23 - B24 11990............................................ C10, C12 TPU............................................. B20 - B21
25775.......................................... B23 - B24 13212...........................................C11 - C12
8355-NY-BL................................ B23 - B24 14269...........................................C11 - C12 VEEJET ® NOZZLES
8360-1/4-NY-BL......................... B23 - B24 14643...........................................C11 - C12 H-DT........................................... B11 - B13
8360-NY-BL................................ B23 - B24 15950............................................ C10, C12 H-DU........................................... B11 - B13
FJ..................................................B22, B24 21550............................................ C10, C12 H-U ............................................ B11 - B13
FJP-PP.........................................B22, B24 36560............................................ C10, C12 H-VV .......................................... B11 - B13
FJP-VS.........................................B22, B24 21550-90NP................................. C10, C12 H-VV-CKY Blue......................... B14 - B15
QJ1/4T-NYB............................... B23 - B24 8510 Strainer..............................C10 - C12 H-VV-CKY Green...................... B14 - B15
QJ1/4TT-NYB............................. B23 - B24 H-VV-CKY Grey......................... B14 - B15
QJ17560A-NY-BL ..................... B23 - B24 PRESSURE RELIEF VALVES H-VV-CKY Light Blue............... B14 - B15
QJ22187-NYB............................ B23 - B24 110................................................... E5 - E7 H-VV-CKY Light Green............. B14 - B15
QJ7421-NYB.............................. B23 - B24 6815................................................. E5 - E7 H-VV-CKY Light Purple............ B14 - B15
QJ8355-NY-BL........................... B23 - B24 8460................................................. E5 - E7 H-VV-CKY Purple...................... B14 - B15
QJ8360-NY-BL........................... B23 - B24 9840................................................. E5 - E7 H-VV-CKY White....................... B14 - B15
QJFJP...........................................B22, B24 23120............................................... E5 - E7 H-VVL ........................................ B11 - B13
T.................................................. B23 - B24
TT................................................ B23 - B24 SIPHON INJECTORS WASHJET ® NOZZLES
13340....................................................... E2 IMEG.............................................. B4 - B7
FULLJET ® NOZZLES 50580....................................................... E2 MEG................................................ B4 - B7
GG .................................................. B2 - B3 WEG............................................... B4 - B7
GG-W............................................. B2 - B3 THROTTLING RELIEF VALVES
HH................................................... B2 - B3 23520............................................... E5 - E7 WASHJET QUICK CONNECT
HH-W ............................................ B2 - B3 NOZZLES
RETAINERS QCIMEG....................................... B8 - B10
GUNJET ® SPRAY GUNS CP1325..................................................B25 QCMEG........................................ B8 - B10
AA30A.............................................C3 - C4 CP8027-NYB.........................................B25
AA30L..............................................C3 - C4 CP18032A-NYB....................................B25 WINDJET ® AIR NOZZLES
AA30L-PP.......................................C3 - C4 CP114444-4-CELR................................B25 AA707 ............................................ D2 - D4
AA60................................................. C2, C4 CP114447-4-CELR................................B25 AA727............................................. D2 - D4
AA70................................................. C2, C4
PW4000A......................................... C2, C4 TRIGGERJET ® SPRAY GUNS
PW4000AS....................................... C2, C4 4688.................................................. C5, C7
1 7 H
110................................................... E5 - E7 7421............................................ B23 - B24 H-DT........................................... B11 - B13
11370.....................................................B26 7630............................................ B27 - B28 H-DU........................................... B11 - B13
11950.....................................................B26 7715.........................................................C8 HH................................................... B2 - B3
11990............................................ C10, C12 HH-W ............................................ B2 - B3
12086.......................................................C8 8 H-U ............................................ B11 - B13
12328....................................................... E4 8079............................................ B27 - B28 H-VV .......................................... B11 - B13
13212...........................................C11 - C12 8460................................................. E5 - E7 H-VV-CKY Blue......................... B14 - B15
13340....................................................... E2 8355-NY-BL................................ B23 - B24 H-VV-CKY Green...................... B14 - B15
14269...........................................C11 - C12 8360-1/4-NY-BL......................... B23 - B24 H-VV-CKY Grey......................... B14 - B15
14643...........................................C11 - C12 8360-NY-BL................................ B23 - B24 H-VV-CKY Light Blue............... B14 - B15
15699.......................................................C8 8510 Strainer..............................C10 - C12 H-VV-CKY Light Green............. B14 - B15
15950............................................ C10, C12 H-VV-CKY Light Purple............ B14 - B15
9 H-VV-CKY Purple...................... B14 - B15
2 9004-SS...................................................C8 H-VV-CKY White....................... B14 - B15
20400.......................................................C8 9527.........................................................C8 H-VVL ........................................ B11 - B13
20400.......................................................C8 9765.............................................. C10, C12
21550............................................ C10, C12 9840................................................. E5 - E7 I
21550-90NP................................. C10, C12 IMEG.............................................. B4 - B7
21950.....................................................B26 A
22650-PP.........................................C6 - C7 AA30A.............................................C3 - C4 K
AA30L..............................................C3 - C4 K ................................................. B18 - B19
22665.......................................................C9
AA30L-PP.......................................C3 - C4
22670-PP.........................................C6 - C7
AA31................................................C6 - C7 M
23120............................................... E5 - E7
AA36................................................C6 - C7 MEG................................................ B4 - B7
23520............................................... E5 - E7
AA60................................................. C2, C4
25775.......................................... B23 - B24 P
AA70................................................. C2, C4
AA707 ............................................ D2 - D4 P ................................................. B16 - B17
3
AA727............................................. D2 - D4 PW4000A......................................... C2, C4
36275....................................................... E3
AACV....................................................... E4 PW4000AS....................................... C2, C4
36560............................................ C10, C12
37235....................................................... E3 ABCV....................................................... E4
Q
B QCIMEG....................................... B8 - B10
4
BACV....................................................... E4 QCMEG........................................ B8 - B10
4067............................................ B27 - B28
BBCV....................................................... E4 QJ1/4T-NYB............................... B23 - B24
4193A ......................................... B27 - B28
QJ1/4TT-NYB............................. B23 - B24
4514............................................ B27 - B28
C QJ17560A-NY-BL ..................... B23 - B24
4676.............................................C11 - C12
CP1325..................................................B25 QJ22187-NYB............................ B23 - B24
4688.................................................. C5, C7
CP8027-NYB.........................................B25 QJ7421-NYB.............................. B23 - B24
5 CP18032A-NYB....................................B25 QJ8355-NY-BL........................... B23 - B24
5053............................................ B27 - B28 CP114444-4-CELR................................B25 QJ8360-NY-BL........................... B23 - B24
50580....................................................... E2 CP114447-4-CELR................................B25 QJFJP...........................................B22, B24
50800-15-PP-1/4.............................C6 - C7
F T
50800-PP-1/4................................... C5, C7
FJ..................................................B22, B24 T.................................................. B23 - B24
6 FJP-PP.........................................B22, B24 TPU............................................. B20 - B21
6051............................................ B27 - B28 FJP-VS.........................................B22, B24 TT................................................ B23 - B24
6104.................................................. C5, C7
G W
6590.................................................. C5, C7
GG .................................................. B2 - B3 WEG............................................... B4 - B7
6671.........................................................C9
GG-W............................................. B2 - B3
6815................................................. E5 - E7
Catalog 25B-M
© 2016 Spraying Systems Co. All rights reserved. Full protection of law claimed under Universal Copyright and Berne Conventions
and other applicable national and international laws.