Professional Documents
Culture Documents
STAAD Pro Subjective Test - 9159482 - 2023 - 06 - 23 - 01 - 37
STAAD Pro Subjective Test - 9159482 - 2023 - 06 - 23 - 01 - 37
a) .dwg b) .dxf
a) 1 b) 2 c) 3 d) 4
a) Bentley b) Autodesk
Q5. As per section 3.8 table 3 of IS 800, the slenderness ratio (l/r) of tension member shall not exceed
a) Triangle b) Rectangle
c) Square d) Hexagon
a) Shift + n b) Shift + b
c) Ctrl + b d) Ctrl + n
a) Steel b) Standard
a) True b) False
Q11. Loads will be distributed on surrounding beams based on one way distribution
a) Area b) Plate
a) Udl b) Uvl
a) Plate b) Surface
Q14. Which command is used to print the density of a member in the final output?
a) Pz=0.6vz.vz b) Pz=0.9vz.vz
Q16. In regular buildings the seismic dynamic analysis is considered for those greater than_____ meters in height for
zones iv and v.
a) 12 m b) 40 m
c) 90 m d) 60 m
c) Support d) Loading
Q18. The maximum diameter of steel in slabs should not exceed_____ the total thickness of slab
a) One-half b) One-fourth
c) One-eighth d) One-sixteenth
Q20. _____ is the Indian code of practice for ductile detailing of reinforced concrete structures subjected to seismic
forces.
a) IS 802 b) IS 800
Q23. The factor will be used for shear & reinforcement design of a foundation
c) Zero d) 20mm
a) True b) False
a) Aspect ratio
b) Modular ratio
c) Span/depth ratio
d) Water/cement ratio
Q31. The maximum strain in concrete at the outermost compression fiber in the limit state design of flexural member
is (as per IS: 456 – 1978)
a) 0.0020
b) 0.0035
c) 0.0065
d) 0.0050
a) 0.0035
b) 0.0015
c) 0.0025
d) 0.015
Q33. When assuming the strength of a structure as per the limit state of collapse, the value of partial safety factor for
steel is taken as
a) 2.0
b) 1.5
c) 1.15
d) 1.00
Q34. What should be the minimum grade of reinforced concrete in and around sea coast construction?
a) M 35
b) M 30
c) M 25
d) M 20
Q35. A reinforced concrete slab is 75mm thick. The maximum size of reinforcement bar that can be used is
a) 12 mm diameter
b) 10 mm diameter
c) 8 mm diameter
d) 6 mm diameter
Q36. As per IS: 456, side face reinforcement, not less than 0.05% of web area, is provided on each side when the depth
of web is not less than
a) 300 mm
b) 400 mm
c) 500 mm
d) 750 mm
Q37. What is the value of minimum reinforcement (in case of Fe 415) in slab?
a) 0.1%
b) 0.12%
c) 0.15%
d) 0.2%
Q38. When the effect of wind and earthquake load is considered in the design of rivets and bolts for steel structures,
by what percentage the permissible stresses may be exceeded?
a) 15%
b) 25%
c) 33.33%
d) 50%
Q39. What is the maximum slenderness ratio permitted as per IS: 800-1984 for design of a tie member subjected to
reversal of stress due to earthquake?
a) 180
b) 250
c) 300
d) 350
Q40. Purlins are provided, in industrial buildings, over roof trusses to carry dead loads, live loads and wind loads. As
per IS code, what are they assumed to be?
a) Simply supported
b) Cantilever
c) Continuous
d) Fixed
a) -1 and 0.5
b) -1 and -0.5
c) 1 and -0.5
d) 0 and 0.5
Q42. The renumber tool has ____ sorting criteria
a) 2 b) 3
c) 4 d) 5
a) Polyline
b) Spline
c) Arc
d) Both option 2 & 3
Q44. Merge selected member tool helps to join two member which are
a) *.grd b) *.gri
Q46. The inactivated members can be restored for further action with_______ command
a) Active member
b) Inactive member
c) Change
d) None of the above
Q47. To generate the plates automatically based on the existing beams, use_______ command
Q48. The bending moment coefficients for continuous RC slabs in IS: 456-1978 code is based on
a) Pigeaud,s method
b) Marcus,s method
c) Yield-line theory
d) Westergaard,s mathematical analysis
Q50. When HYSD bars are used in place of mild steel bars in a beam, the bond strength