Professional Documents
Culture Documents
RL177: All functional information must be included in 3D model. Tolerance of form, orientation, location and run-out.
IMPLEMENT CLOSE
PMP OPEN SELECT DO PRODUCE RL121: No created dimension on drawing.
process RL116: No over-write dimensions. Tolerance zone parameter Examples Other possible
A B C D E+F RL174: All the nonfunctional dimensions use the general Tolerance
EMA Meaning Symbole Position Tolerance zone Expression Interpretation notations
feature
process
Pre-Study
the technical
Study the tolerances standard. General tolerances standard must be
solution
solution indicated on an additional document: “General Tolerances and 0,05
LIGNE ∅ 0,05
ELM 5-Define sub Specifications”. (generator or Without
Activities assemblies & Straightness Datum t
components edge) 0,05/100
0,05
Functional Dimensioning Distance between 2 straight // lines
FORM
ELM Work Process Datum 0,1
or/and the geometric tolerance and the “Tolerance Manager” name. Distance between 2 // planes
Create new part with CAD document RL180: Geometrical tolerance values are defined by dimension
0,1
Create CAD document Symphony chains analysis. Define only Geometrical tolerances level Safety / 0,1
LIGNE t
CODA Working / Performance severity and weight > 2%. Other Without
Roundness (N sections
geometrical tolerances are not selected and not shown on the Datum
of a cylinder
Define functional dimensionning drawing. or cone) Distance between 2 concentric circles
Process of robust design. t
0,2
Representation Without
Functional Dimensioning Cylindricity CYLINDER Datum 0,1/100
TM
Distance between 2 coaxial cylinders 0,2
Use standard
0,3
ISO 8015 Line Profile With
t 0.3
LIGNE
ISO128-30 or Without 0,3 A B
Datum
ISO129-1 Pro/Eng.
ISO1101
0,5
ISO5458 Use Standard Surface With 0.5
ISO5459
SURFACE or Without 0,5 A B
Profile
Datum
ISO1302 ISO 8015 t
ORIENTATION
Pro/Eng. dimensional or geometrical requirement on a drawing shall be met Datum t PL2
Additional note Parallelism Surface
independantly… unless a particular relationship is specified. » required
0,5 A-B
Part information notification : Consequently: « If a particular relationship of size and form, or size B
Dat B
and orientation, size and location, is required,” (by functional 0,2
requirement)“ it shall be specified on the drawing »… Datum t Øt
0,2 C ∅ 0,2 C
Perpendi- Ligne
Create New Part with CAD Document RL120: To apply the ISO8015, Apply geometrical tolerances
cularity Surface required
according to RL180. Apply general tolerances standard to C 0,2 C
Create CAD Document nonfunctional surfaces. Functional surfaces are used in dimension Dat C
PL1
¨See FTD00031 for CAD numbering explanations chains to satisfy Functional Condition. PL2
0,5
Ligne
0,5 A ∅ 0,5 A
Angularity Datum
Surface t
Symphony gives non-significant numbers. required
0,5 A-B
RL166: Create CAD document in Symphony before creating new A 38°
E01 Dat A
object in Pro/E launched via Pro/Intralink workspace, to avoid L01 t1 1 E 1 Ø1 A B C
renaming afterwards.
Point
RL110: Create an additional document for General Tolerances and Position Ligne
Datum Øt 4 holes Ø 0.1
Specification (GT&S). required
LOCATION
Surface t2 Ø 0.1
This document content: ISO8015 principle, general tolerances t E Ø1 A B C
Dat E
class, general geometric tolerances class, general surface texture ISO 128-30 Øt ∅ 0,1
tolerance and all important specifications to define the part. First angle for the view projection, the line thickness, letter height. Concentricity Ø 0.1 D M
ou Point Datum
Ligne required c e
Coaxiality en Øt ∅ 0,1 D Réf D Ø 0.1 A-B
fér D
ré
Define Functional Dimensioning
t 0,2 F Dat F
Process of Robust Design t
Symmetry Ligne Datum 0 ,2 0.1 A-B
Surface required
F Common datum
référence
t 0,1
t
Ligne
RUN-OUT
Forbidden use:
ISO 1101 ISO 5459
RL089: The width of the tolerance zone applies normal to the Datums and Datum-systems for geometrical tolerances ISO 5459
specified geometry unless otherwise indicated. Datums Establishment of Datums Datum-system established by two or more features
Datum-Centre point: Three-plane datum-system
Note : The orientation alone of the leader line does not influence Centre-point of a sphere Usually only one or two datums are required for orientation
the definition of the tolerance. tolerances, positional relationships, however, often require a three-
plane datum-system in which the three planes are mutually
perpendicular. It may be necessary to decide the order of
precedence according a functional approach.
Standardized Representation
for Technical Drawing
Datum-line: Axis of a hole
Quick Reference Guide
ISO 5458
Datum-plane:
Surface of a part
Positional tolerancing
Datum targets
- a point : it is indicated by a
Bidirectional position: cross.
- A line : it is indicated by two
crosses, connected by a
thin continuous line
- An area : it is indicated by a
hatched area.
Complementary Rules
Common datum established
by two features Additional Note:
RL112: - Add revision level balloon near the evolution : we keep
only the balloons related to the last evolution.