Professional Documents
Culture Documents
3. The code requires that being panels be separated from outlet boxes that are
to be used for mounting fixtures not less than ___ inches.
(a) 12
(b) 8
(c) 6
(d) 10
4. At least ___ inches of free conductor shall be left at each outlet and switch
point.
(a) 4
(b) 6
(c) 8
(d) 12
7. Lamp tie wires, mounting screws, and decorative bands on glass lamps
space not less than ___ inches from lamp terminals shall be required to be
grounded.
(a) 1.25
(b) 1.5
(c) 2
(d) 4
9. Where conduit is threaded in the field, a standard conduit cutting due with
a ___ inch taper per foot shall be used.
(a) 0.5
(b) 0.75
(c) 1
(d) 1.25
12. The minimum feeder allowance for show window lighting expressed in
volts-amps per linear foot shall be ___ VA.
(a) 100
(b) 200
(c) 300
(d) 180
13. Angle pull dimensional requirements apply to junction boxes only when
the size of conductor is equal to or larger than ___.
(a) #0
(b) #4
(c) #3/0
(d) #6
17. Which of the following may be used as a feeder from the service
equipment to a mobile home?
(a) I only
(b) II only
(c) Either I or II
(d) Neither I nor II
18. Multispeed motors shall be marked with the code letter designating the
locked-rotor ___ per HP for the highest speed at which the motor can be
started.
(a) Amps
(b) FLC
(c) KVA
(d) WATSS
19. The length of a type S cord connecting a trash compactor must not exceed
___.
(a) 18”
(b) 4’
(c) 36”
(d) 2’
22. The space measures horizontally above a show window must have at least
one receptacle for each ___ linear feet.
(a) 12
(b) 10
(c) 8
(d) 6
24. The distance between a cable or conductor entry and it’s exist from the
box shall be not less than ___ times the outside diameter, over sheath, of
that cable or conductor, 1000 volts system.
(a) 6
(b) 18
(c) 38
(d) 48
25. A thermal barrier shall be required if the space between the resistors and
reactors and any combustible materials is less than ___ inches.
(a) 4
(b) 6
(c) 8
(d) 12
26. An attachment plug connecting to a receptacle shall ___ the equipment
grounding conductor.
(a) Have conductors the same size as
(b) Provides for first-make, last-break of
(c) Provide a twist-lock connection for
(d) None of these
27. When more than one calculated or tabulated ampacity could apply for a
given circuit length, the ___ value shall be used.
(a) Lowest
(b) Average
(c) Highest
(d) None of these
29. Electronically actuated fuses may or may not opera in current limiting
fashion, depending on the ___.
(a) Ambient temperature
(b) Type of control selected
(c) Listing
(d) Torque
30. Connection by means of wire binding screws or studs and nuts having
upturned lugs or equivalent shall be permitted for ___ or smaller
conductors.
(a) #10
(b) #8
(c) #6
(d) None of these
33. Pull-type canopy switches shall not be located more than ___ from the
center of the canopy
(a) 1.5”
(b) 2”
(c) 3”
(d) 3.5”
34. Means shall be provided to ensure that the ___ is energized when the first
heater ___ is energized.
(a) Ballast
(b) Fan circuit
(c) Coil
(d) Relay
35. A pool recirculating pump motor receptacle shall be permitted not less
than ___ feet to the inside walls of the pool.
(a) 5
(b) 8
(c) 10
(d) 15
36. Fixture shall be wired with conductors having insulation suitable for ___
to ___ the conductors will be subjected.
I. Environmental conditions
II. Current-voltage
III. Temperature
(a) II only
(b) III only
(c) I, II, and III
(d) II and III
37. What is the minimum working clearance on circuit 120 volts to ground,
exposed live parts on one side and no live or ground parts grounded parts
on the other side the working space?
(a) 3’
(b) 1.5’
(c) 4’
(d) 4’
38. The maximum weight of a light fixture that may be mounted on the
screw shell of a brass socket is ___ pound(s).
(a) 0.5
(b) 1
(c) 6
(d) None of these
39. The grounded service conductors shall not be smaller than the required
___.
(a) Grounding electrode conductor
(b) Largest phase conductor
(c) Ungrounded service conductor
(d) Largest equipment conductor
40. Type UF cable shall be permitted for interior wiring in ___ locations
I. Dry
II. Wet
III. Corrosive
(a) I only
(b) I or II
(c) I or III
(d) I, II or III
42. For feeder and service calculations a maximum of ___ of lighting track or
fraction thereof shall be considered 150VA
(a) 2’
(b) 4’
(c) 5’
(d) 8’
43. Under the optional method of calculation other load are permitted a
demand factor from table 220-30, the first 10 KVA of other load @ 100%
and the remainder ___ at load at 40%, other load could consist of which of
the following?
I. Electric heat
II. Electric range
III. Air conditioning
(a) I only
(b) II only
(c) III only
(d) I, II and III
44. Reasonable efficiency of operation can be provided when ___ is taken into
consideration in sizing the service-lateral conductors.
(a) Mechanical strength
(b) Ambient Temperature
(c) Voltage Drop
(d) None of these
45. Voltage shall not exceed 600 volts between conductors on branch circuits
supplying only ballast for electric-discharge lams in tunnels with a height of
not less than ___ feet.
(a) 12
(b) 16
(c) 18
(d) 22
47. The conductor a lighting arrester and the line for installations operating
at 100 volts or more must be at least ___.
(a) #14 copper
(b) #6 copper
(c) #8 copper
(d) None of these
48. What is the nominal battery voltage for an alkali type battery per cell?
(a) 2 volt6s
(b) 6 volts
(c) 1.5
(d) 1.2 volts
49. The conductors and equipment required or permitted by this code shall
be acceptable only if ___.
(a) Approved
(b) Identified
(c) Labeled
(d) Listed
50. Where multiple rod, pipe, or plate electrodes are installed they shall be
not less than ___ apart.
(a) 18”
(b) 6’
(c) 8’
(d) 10’