Professional Documents
Culture Documents
Albay-Legazpi Chapter
Legazpi City
1. At least ____ of free conductor shall be left at each outlet, junction and switch point for splices or the connection
of fixtures or devices.
a.) 200 mm c.) 150 mm
b.) 100 mm d.) 300 mm
2. Which of the following electrodes shall not be permitted?
I. Rod and pipe electrodes II. Plate electrodes III. Aluminum electrodes
a.) I and II c.) I and III
b.) II and III d.) III only
3. Knife switches rated at over ____ amperes at 250 volts or less, and not over 600 amperes at 251 to 600 volts,
shall be used only as isolating switches and shall not be opened under load.
a.) 1000 c.) 1500
b.) 1200 d.) 1600
4. System voltage in watercraft for both alternating current & direct current shall not exceed:
I. 500 V for cooking and heating equipment permanently connected to fixed wiring.
II. 250 V for lighting, heaters in cabins and public rooms, and other applications not mentioned above.
III. 55 V for emergency systems.
a.) I only c.) I & II only
b.) II only d.) I, II & III only
5. The rating of a silicon carbide-type surge arrester shall be not less than _____ percent of the maximum
continuous phase-to-ground voltage available at the point of application.
a.) 125 c.) 100
b.) 115 d.) 80
6. What shall be the minimum size of equipment grounding for a panelboard having 1000 AT mains?
a.) 80 mm2 copper conductor c.) 50 mm2 aluminum conductor
2
b.) 60 mm copper conductor d.) 80 mm2 aluminum conductor
7. For service-entrance phase conductors larger than 500 mm 2 copper or 850 mm2 aluminum, the grounded
conductor shall not be smaller than ____ of the area of the largest service -entrance phase conductor.
a.) 10 percent c.) 15 percent
b.) 12 ½ percent d.) 17 ½ percent
8. Direct burial cable shall be permitted to be spliced or tapped without the use ____, provided they are installed
using materials suitable for the application.
a.) junction box c.) pull box
b.) splice boxes d.) utility box
9. A reliable conductor used to ensure the required conductivity between metal parts which are to be electrically
connected is called which of the following:
a.) Connector c.) Insulated conductor
b.) Bonding jumper d.) Branch connector
10. Wireways shall not contain more than ____ current-carrying conductors at any cross-section.
a.) 15 c.) 25
b.) 20 d.) 30
11. Unless identified for use in the operating environment, no conductors or equipment shall be located in ______
having a deteriorating effect on the conductors or equipments.
I. Damp or wet locations II. where exposed to gases, fumes, vapors, liquids, etc.
a.) I only c.) both I and II
b.) II only d.) neither I nor II
12. It is the ratio of the maximum demand of a system, or part of a system, to the total connected load of a system
or the part of the system under consideration.
a.) Utilization factor c.) Diversity factor
b.) Demand factor d.) Average load factor
13. A 25 hp 460 V 3-phase motor bears the code letter F and specifies a temperature rise of 40 °C. Determine the
locked-rotor current required.
a.) 156.57 A c.) 125.20 A
b.) 197.37 A d.) 175.40 A
14. The rating of a time-delay fuse (dual-element) shall be permitted to be increased but shall in no case exceed
___ of the full-load current.
a.) 125% c.) 225%
b.) 150% d.) 400 %
15. Clearance in any direction to the water level, edge of water surface, base of diving platform, or permanently
anchored raft for insulated supply or service droop cables 0 up to 750 volts to ground…
a.) 3,700 mm c.) 4,300 mm
b.) 5,500 mm d.) 6,700 mm
FA
b.) F d.)
1. At least ____ of free conductor shall be left at each outlet, junction and switch point for splices or the connection
of fixtures or devices.
a.) 200 mm c.) 150 mm
b.) 100 mm d.) 300 mm
2. Which of the following electrodes shall not be permitted?
I. Rod and pipe electrodes II. Plate electrodes III. Aluminum electrodes
a.) I and II c.) I and III
b.) II and III d.) III only
3. Knife switches rated at over ____ amperes at 250 volts or less, and not over 600 amperes at 251 to 600 volts,
shall be used only as isolating switches and shall not be opened under load.
a.) 1000 c.) 1500
b.) 1200 d.) 1600
4. System voltage in watercraft for both alternating current & direct current shall not exceed:
I. 500 V for cooking and heating equipment permanently connected to fixed wiring.
II. 250 V for lighting, heaters in cabins and public rooms, and other applications not mentioned above.
III. 55 V for emergency systems.
a.) I only c.) I & II only
b.) II only d.) I, II & III only
5. The rating of a silicon carbide-type surge arrester shall be not less than _____ percent of the maximum
continuous phase-to-ground voltage available at the point of application.
a.) 125 c.) 100
b.) 115 d.) 80
6. What shall be the minimum size of equipment grounding for a panelboard having 1000 AT mains?
a.) 80 mm2 copper conductor c.) 50 mm2 aluminum conductor
2
b.) 60 mm copper conductor d.) 80 mm2 aluminum conductor
7. For service-entrance phase conductors larger than 500 mm 2 copper or 850 mm2 aluminum, the grounded
conductor shall not be smaller than ____ of the area of the largest service -entrance phase conductor.
a.) 10 percent c.) 15 percent
b.) 12 ½ percent d.) 17 ½ percent
8. Direct burial cable shall be permitted to be spliced or tapped without the use ____, provided they are installed
using materials suitable for the application.
a.) junction box c.) pull box
b.) splice boxes d.) utility box
9. A reliable conductor used to ensure the required conductivity between metal parts which are to be electrically
connected is called which of the following:
a.) Connector c.) Insulated conductor
b.) Bonding jumper d.) Branch connector
10. Wireways shall not contain more than ____ current-carrying conductors at any cross-section.
a.) 15 c.) 25
b.) 20 d.) 30
11. Unless identified for use in the operating environment, no conductors or equipment shall be located in ______
having a deteriorating effect on the conductors or equipments.
II. Damp or wet locations II. where exposed to gases, fumes, vapors, liquids, etc.
a.) I only c.) both I and II
b.) II only d.) neither I nor II
12. It is the ratio of the maximum demand of a system, or part of a system, to the total connected load of a system
or the part of the system under consideration.
a.) Utilization factor c.) Diversity factor
b.) Demand factor d.) Average load factor
13. A 25 hp 460 V 3-phase motor bears the code letter F and specifies a temperature rise of 40 °C. Determine the
locked-rotor current required.
a.) 156.57 A c.) 125.20 A
b.) 197.37 A d.) 175.40 A
14. The rating of a time-delay fuse (dual-element) shall be permitted to be increased but shall in no case exceed
___ of the full-load current.
a.) 125% c.) 225%
b.) 150% d.) 400 %
15. Clearance in any direction to the water level, edge of water surface, base of diving platform, or permanently
anchored raft for insulated supply or service droop cables 0 up to 750 volts to ground…
a.) 3,700 mm c.) 4,300 mm
b.) 5,500 mm d.) 6,700 mm
FA
b.) F d.)